PDN-IF-EXT-CONFIG-MIB
Imported Objects
Objects
13 total| Object Name |
|---|
pdnIfXLinkConfigTableThis table contains configuration information
for interfaces that are capable of switch roles
at run-time. SEQUENCE OF PdnIfXLinkConfigEntry .1.3.6.1.4.1.1795.2.24.2.6.12.1.3 |
pdnIfXLinkConfigEntryAn entry in this table represents an interface
that is capable of being used as an uplink.
Typically, this table will contain entries only
for interfaces that are capable of switching roles. PdnIfXLinkConfigEntry .1.3.6.1.4.1.1795.2.24.2.6.12.1.3.1 |
pdnIfXLinkConfigRoleThis object allows users to configure the role
(e.g., uplink) intended for this interface.rw PdnLinkRole .1.3.6.1.4.1.1795.2.24.2.6.12.1.3.1.1 |
pdnIfExtEncapConfigThis Mib is created to facilitate
configuration of interface related objects. MODULE-IDENTITY .1.3.6.1.4.1.1795.2.24.2.6.12.3 |
pdnIfMultiprotocolEncapConfigTableThis table that contains additional
interface configuration information. SEQUENCE OF PdnIfMultiprotocolEncapConfigEntry .1.3.6.1.4.1.1795.2.24.2.6.12.3.1 |
pdnIfMultiprotocolEncapConfigEntryThere will be one of these rows for each interface that
supports RFC1483. PdnIfMultiprotocolEncapConfigEntry .1.3.6.1.4.1.1795.2.24.2.6.12.3.1.1 |
pdnIfMultiprotocolEncapConfigIPRoutedPDUsIn the upstream direction user can configure the IP
routed PDUs in the LLC SNAP encapsulation or VC Based
Multiplexing encapsulation (RFC1483). If neither is
configured 'none' is used. The direction is determined
by the transmit direction. Initialy this object was
developed for the endpoint use where the transmit direction
is upstream. This object could be used for CO type equipment
where the direction would be downstream.rw Enumeration .1.3.6.1.4.1.1795.2.24.2.6.12.3.1.1.1 |
pdnIfMultiprotocolEncapConfigBridgedPDUsIn the transmit direction user can configure the IP
routed PDUs in the LLC SNAP encapsulation or VC Based
Multiplexing encapsulation (RFC1483). If neither is
configured 'none' is used.rw Enumeration .1.3.6.1.4.1.1795.2.24.2.6.12.3.1.1.2 |
pdnIfMultiprotocolEncapMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.12.3.2 |
pdnIfMultiprotocolEncapMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.12.3.2.1 |
pdnIfMultiprotocolEncapCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.12.3.2.2 |
pdnIfXConfigMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.12.4 |
pdnIfXConfigMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.12.4.1 |
More MIBs from Pdyn
Browse all PdynMIBs →Standard SNMP MIB module defining data structures for PDN-HEADER-MIB.
Standard SNMP MIB module defining data structures for HOTWIRE-MSDSL-INTERFACE-MIB.
The PDN-DSL-ATM-BOND-MIB manages Paradyne Networks hardware to aggregate multiple DSL physical links into a single logical interface for transporting ATM streams, monitoring bonding session states and aggregate throughput metrics. This module provides vendor-specific visibility into multi-pair bonding configurations where standardized IETF or ATM Forum MIBs were unavailable, tracking the operational status and performance of the bonded ATM transport layer.
The PDN-CONTROL-MIB facilitates remote device reset operations and firmware or configuration file management on DSLAM hardware via SNMP. It provides the necessary control objects to execute system reboots and manage the storage and retrieval of critical operational binaries and settings.
SNMP MIB module
The PDN-ADSL-LINE-EXT-MIB extends standard ADSL-LINE-MIB definitions to monitor non-standard ADSL2 and ADSL2plus physical layer parameters and operational states on Paradyne DSLAM hardware. This module provides temporary vendor-specific visibility into line modulation modes, error counters, and signal quality metrics required for managing next-generation ADSL technologies before IETF standardization was completed.