PDN-ADSL-LINE-EXT-MIB
AI MIB Summary
The PDN-ADSL-LINE-EXT-MIB extends standard ADSL-LINE-MIB definitions to monitor non-standard ADSL2 and ADSL2plus physical layer parameters and operational states on Paradyne DSLAM hardware. This module provides temporary vendor-specific visibility into line modulation modes, error counters, and signal quality metrics required for managing next-generation ADSL technologies before IETF standardization was completed.
This MIB module is a supplement to the ADSL-LINE-MIB and to the ADSL-LINE-EXT-MIB, the `standard` MIBs, where additional objects are needed to support ADSL modes or flavors not covered in the `standard` MIBs. At the time this MIB was defined, the IETF ADSL MIB Working does not have any work on the 'standard' MIBs planned and/or has not produced a schedule to address ADSL2/ADSL2plus needs. As a result, these objects may be a `temporary' solution until MIBs/Objects are defined or extended to meet the needs of ADSL2/ADSL2plus. The following documents that should be referenced with respect to this MIB: [G.997.1] ITU-T G997.1 `Physical layer management for Digital Subscriber Line (DSL) transceivers', May 2003. [G.991.1 Am 1] ITU-T-G997.1 Amendment 1 `Physical layer management for Digital Subscriber Line (DSL) transceivers Amendment 1', December 2003. [OA 305] Telenor Networks Specification, Specification Number OA 305, `Requirements for equipment to be connected to the local sub-loop in the access network of Telenor. Equipment providing ADSL and PSTN or ISDN Basic Access Services, full unbundled access (service type EDF)', TN-NL-U-T/OA305/0101 2005, Edition 4.1, January 1, 2005. [WT-090] DSL Forum Working Text WT-090 `Protocol Independent Object Model for Managing Next Generation ADSL Technologies', Revision-1, September 2003. [WT-090-4] DSL Forum Working Text WT-090 `Protocol Independent Object Model for Managing Next Generation ADSL Technologies', Revision-4, June 2004. [RFC 2662] Bathrick, G., Ly, F. `ADSL-LINE-MIB', August 1999. [RFC 3440] Ly, F., Bathrick, G. `ADSL-LINE-EXT-MIB', December 2002. Generally the MIB objects are defined using G.997.1 and the MIB objects are arranged using WT-090. ===================================================================== == == == Copyright (C) 2004 Paradyne Corporation. == == == =====================================================================
Main OID:
pdnAdslLineExtMIB.1.3.6.1.4.1.1795.2.24.2.6.24
96
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
96 total| Object Name |
|---|
pdnAdslLineExtMIBThis MIB module is a supplement to the ADSL-LINE-MIB and to the ADSL-LINE-EXT-MIB, the `standard` MIBs, where additional objects are needed to support ADSL modes or flavors not covered in the `standard` MIBs. At the time this MIB was defined, the IETF ADSL MIB Working does not have any work on the 'standard' MIBs planned and/or has not produced a schedule to address ADSL2/ADSL2plus needs. As a result, these objects may be a `temporary' solution until MIBs/Objects are defined or extended to meet the needs of ADSL2/ADSL2plus. The following documents that should be referenced with respect to this MIB: [G.997.1] ITU-T G997.1 `Physical layer management for Digital Subscriber Line (DSL) transceivers', May 2003. [G.991.1 Am 1] ITU-T-G997.1 Amendment 1 `Physical layer management for Digital Subscriber Line (DSL) transceivers Amendment 1', December 2003. [OA 305] Telenor Networks Specification, Specification Number OA 305, `Requirements for equipment to be connected to the local sub-loop in the access network of Telenor. Equipment providing ADSL and PSTN or ISDN Basic Access Services, full unbundled access (service type EDF)', TN-NL-U-T/OA305/0101 2005, Edition 4.1, January 1, 2005. [WT-090] DSL Forum Working Text WT-090 `Protocol Independent Object Model for Managing Next Generation ADSL Technologies', Revision-1, September 2003. [WT-090-4] DSL Forum Working Text WT-090 `Protocol Independent Object Model for Managing Next Generation ADSL Technologies', Revision-4, June 2004. [RFC 2662] Bathrick, G., Ly, F. `ADSL-LINE-MIB', August 1999. [RFC 3440] Ly, F., Bathrick, G. `ADSL-LINE-EXT-MIB', December 2002. Generally the MIB objects are defined using G.997.1 and the MIB objects are arranged using WT-090. ===================================================================== == == == Copyright (C) 2004 Paradyne Corporation. == == == ===================================================================== MODULE-IDENTITY .1.3.6.1.4.1.1795.2.24.2.6.24 |
pdnAdslLineExtNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.0 |
pdnAdslLineExtObjects OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.1 |
pdnAdslLineExtTableThis table extends the adslLineTable in support of an ADSL Line object. The objects pdnAdslLineTransAtucCap, pdnAdslLineTrans- AtucConfig, and pdnAdslLineTransAtucActual exist along with their PdnAdslTransmissionModeType TC because the AdslTransmissionModeType defined in the ADSL-LINE-EXT-MIB does not include the ADSL2/ADSL2plus bits defined in ITU G.997.1 (05/2003) ATU Transmission System Enabling (ATSE) section. When using the objects defined in this MIB with a syntax of type PdnAdslTransmissionModeType, the interworking relationship between these objects and the objects defined in the ADSL-LINE- EXT-MIB defined with a syntax of type AdslTransmissionModeType must be considered and explained in an implementation-specific document such as an Operational Specification. Note that the PdnAdslTransmissionModeType is a super set of the AdslTransmis- sionModeType. One possible implementation could be as follows: 1. Both objects of syntax AdslTransmissionModeType defined in the ADSL-LINE-EXT-MIB and objects of syntax PdnAdsl- TransmissionModeType defined in this MIB are supported. By supporting both, a manager with the ADSL-LINE-EXT-MIB loaded could manage the device with the restriction of not being able to utilize ADSL2/ADSL2plus modes. 2. When the ADSL2/ADSL2plus capabilities are desired, a manager would have to use the objects defined in this MIB to configure the transmission modes, read capability, or read the actual transmission mode of the ATU-C. 3. The transmission mode that the ATU-C is currently configured for is based on the last object, adslLineTrans- AtucConfig or pdnAdslLineTransAtucConfig, that was written. SEQUENCE OF PdnAdslLineExtEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.1 |
pdnAdslLineExtEntryAn extended entry in the adslLineTable. PdnAdslLineExtEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1 |
pdnAdslLineTransAtucCapThe transmission modes, represented by a bitmask that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment.ro PdnAdslTransmissionModeType .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.1 |
pdnAdslLineTransAtucConfigThe transmission modes, represented by a bitmask, currently enabled by the ATU-C. The manager can only set those modes that are supported by the ATU-C. An ATU-C's supported modes are provided by pdnAdslLineTransAtucCap.rw PdnAdslTransmissionModeType .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.2 |
pdnAdslLineTransAtucActualThe actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit Remote terminal end (ATU-R) will determine the mode used for the link. This value will be limited a single transmission mode that is a subset of those modes enabled by the ATU-C and denoted by pdnAdslLineTransAtucConfig. After an initialization has occurred, its mode is saved as the `Current' mode and is persistent should the link go down. This object returns 0 (i.e. BITS with no mode bit set) if the mode is not known.ro PdnAdslTransmissionModeType .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.3 |
pdnAdslLinePowerManagementConfigThis object enables or disables power management functionality.rw Enumeration .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.4 |
pdnAdslLineSpectrumProfileThe value of this object identifies the row in the ADSL Line Spectrum Profile Table, pdnAdslLineSpectrumProfileTable, which applies for this ADSL line. If this object is not a zero-length string, it should default to the default profile whose name is `DEFVAL'.rw SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.5 |
pdnAdslLinePmModeThe line states the ATU-C or ATU-R may autonomously transition to on this line. It is coded in a bit-map representation (0 if not allowed, 1 if allowed) as follows: idleStateL3(0) - Bit 0 L3 state (Idle state) lowPwrStateL1L2(1) - Bit 1 L1/L2 state (Low power state)rw Bits .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.6 |
pdnAdslLineL0TimeThe minimum time, in seconds, between and Exit from the L2 state and the next Entry into the L2 state.rw Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.7 |
pdnAdslLineL2TimeThe minimum time, in seconds, between an Entry into the L2 state and the first Power Trim in the L2 state and between two con- secutive Power Trims in the L2 State.rw Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.8 |
pdnAdslLineL2AtprThe maximum aggregate transmit power reduction, in dB, that can be performed through a single Power Trim in the L2 state. At the time this MIB was produced, the upper limit for this object was not updated in the G.997.1 with respect to ADSL2plus. As such, the upper limit of this object should be defined in an implementation- specific document such as an Operational Specification.rw Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.9 |
pdnAdslLineLdsfDefines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line. ldsfMode0(1) - 0: Inhibits the near-end ATU from performing loop diagnostics mode procedures on the line. Loop diagnostic mode procedures may still be initiated by the far-end ATU. ldsModef1(2) - 1: Forces the near-end ATU to perform the loop diagnostics procedures. The line needs to be forced to the L3 state (idle state) before it can be forced to the loop diagnostics mode. Only while the line power management state is the L3 state, the line can be forced into the loop diagnostics mode procedures. The following are ways to force the line to the L3 state: (1) Set the ifAdminStatus to down. When the loop diagnostics mode procedures are completed successfully, this object shall reset to ldsf0 and the line shall return to and remain in the L3 idle state. The loop diagnostics data shall be available at least until the line is forced to the L0 state. If the loop diagnostics procedures can't be completed successfully, then an Initialization Failure occurs. As long as loop diagnostics procedures are not completed successfully, attempts shall be made to do so, until the loop diagnostics mode is no longer forced on the line through this configuration parameter.rw Enumeration .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.10 |
pdnAdslLineL2AtprtThis parameter represents the total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims.rw Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.11 |
pdnAdslLineSpectrumProfileTableThis table contains specific configuration of transmission spectrum and power spectral density related parameters that can be mapped to one of the ADSL lines. SEQUENCE OF PdnAdslLineSpectrumProfileEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.2 |
pdnAdslLineSpectrumProfileEntryEach entry contains a specific profile for transmission spectrum and power spectral density related parameters. A default profile with an index of `DEFVAL', will always exist and its parameters will be set to vendor or product specific values, unless otherwise specified in this document. PdnAdslLineSpectrumProfileEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1 |
pdnAdslLineSpectrumProfileNameThis object identifies a row in the pdnAdslLineSpectrumProfile- Table. The system will always provide a default profile whose name is `DEFVAL'. SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.1 |
pdnAdslLineSpectrumProfileRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `valid'. Before a profile can be deleted or taken out of service, by setting this object to `destroy' or `outOfService', the profile must be first unreferenced from all entries that referred to it (entries in the pdnAdslLineExtTable).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.2 |
pdnAdslLineSpectrumModeSpecificPsdProfileThe value of this object identifies the row(s) in the ADSL Mode-Specific PSD Configuration Table, pdnAdslModeSpecific- PsdConfTable, which applies for this Line Spectrum Profile. A particular ADSL line may need to support multiple mode- specific power spectral density related settings. For example, a ADSL line may need to support one set of settings for ADSL2 and another set of settings for ADSL2plus. See the pdnAdslMode- SpecificPsdConfTable for additional detail. The system will always provide a default profile whose name is `DEFVAL'rw SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.3 |
pdnAdslLineSpectrumAtucCarMaskProfileThis object identifies one or more rows in the pdnAdslCarMaskTable. The pdnAdslCarMaskTable is a table containing a list of subcarriers to be masked in the downstream or upstream direction; the profile in the pdAdslCarMaskTable that this object identifies will apply the masks in the downstream direction. This object defaults to an empty string meaning that no subcarriers are masked by an administrator.rw SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.4 |
pdnAdslLineSpectrumAturCarMaskProfileThis object identifies one or more rows in the pdnAdslCarMaskTable. The pdnAdslCarMaskTable is a table containing a list of subcarriers to be masked in the downstream or upstream direction; the profile in the pdAdslCarMaskTable that this object identifies will apply the masks in the upstream direction. This object defaults to an empty string meaning that no subcarriers are masked by an administrator.rw SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.2.1.5 |
pdnAdslModeSpecificPsdConfTableThis table binds an entry indexed by a specific ADSL type or flavor (e.g. ADSL2 or ADSL2+) and indexed by a profile name to a specific DSL PSD Configuration Profile. SEQUENCE OF PdnAdslModeSpecificPsdConfEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.3 |
pdnAdslModeSpecificPsdConfEntryAn entry in the table. For each particular ADSL mode or flavor supported (pdnAdslMOdeSpecificPsdConfAdslMode), there will be an entry that points to an entry in the ADSL PSD Configuration Table (pdnAdslPsdConfTable). For example, if ADSL2 and ADSL2plus ADSL modes are supported, this table will have the following two default entries: 1. An entry indexed by pdnAdslModeSpecificPsd- ConfProfileName = 'DEFVAL' and pdnAdslModeSpecific- PsdConfAdslMode = adsl2(1) and has pdnAdslModeSpecific- PsdConfAdslPsdConfProfile = DEFVAL_ADSL2 2. An entry indexed by pdnAdslModeSpecificPsd- ConfProfileName = 'DEFVAL' and pdnAdslModeSpecific- PsdConfAdslMode = adsl2plus(3) and has pdnAdslModeSpecific- PsdConfAdslPsdConfProfile = DEFVAL_ADSL2PLUS DEFVAL entries may be modified but not deleted. PdnAdslModeSpecificPsdConfEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1 |
pdnAdslModeSpecificPsdConfProfileNameThis object identifies a row in the pdnAdslModeSpecificPsdConfTable. The system will always provide a default profile whose name is 'DEFVAL'. SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.1 |
pdnAdslModeSpecificPsdConfAdslModeThis object identifies a row in the pdnAdslModeSpecificPsdConfTable containing parameters specific to a particular ADSL mode or flavor identified by this object. Enumeration .1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.2 |
pdnAdslModeSpecificPsdConfRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `valid'. Before a profile can be deleted or taken out of service, by setting this object to `destroy' or `outOfService', the profile must be first unreferenced from all entries that referred to it (entries in the pdnAdslLineSpectrumProfileTable).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.3 |
pdnAdslModeSpecificPsdConfAdslPsdConfProfileThis object identifies a row in the ADSL PSD Configuration Table, pdnAdslPsdConfTable.rw SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.3.1.4 |
pdnAdslPsdConfTableThis table contains power spectral density settings. SEQUENCE OF PdnAdslPsdConfEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.4 |
pdnAdslPsdConfEntryEach entry contains specific power spectral density settings for a particular profile. A default profile for each particular ADSL mode or flavor supporting PSD configuration will exist (See the pdnAdslModeSpecificPsdConfAdslMode object the the range of possible ADSL modes or flavors that are possible). For example, if only ADSL2 and ADSL2plus modes are supported, the indices would be 'DEFVAL_ADSL2' and 'DEFVAL_ADSL2PLUS'. The DEFVAL rows may be modified but not deleted. The DEFVAL rows will always exist and its parameters will be set to vendor or product specific values, unless otherwise specified in this document. PdnAdslPsdConfEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1 |
pdnAdslPsdConfProfileNameThis object identifies a row in the pdnAdslPsdConfTable. SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.1 |
pdnAdslPsdConfRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `valid'. Before a profile can be deleted or taken out of service, by setting this object to `destroy' or `outOfService', the profile must be first unreferenced from all entries that referred to it such as pdnAdslModeSpecificPsdConfAdslPsdConfProfile.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.2 |
pdnAdslPsdConfAtucMaxNomPsdRepresents the Maximum nominal transmit PSD for the ATU-C. The values range from -80 to -40 dBm/Hz in 0.1 dB steps.rw Integer32(-800..-400) UNITS "tenth dBm/Hz" .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.3 |
pdnAdslPsdConfAturMaxNomPsdRepresents the Maximum nominal transmit PSD for the ATU-R. The values range from -65 to -38 dBm/Hz in 0.1 dB steps.rw Integer32(-650..-380) UNITS "tenth dBm/Hz" .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.4 |
pdnAdslPsdConfAtucMaxNomAtpRepresents the Maximum nominal aggregate transmit power for the ATU-C. The values range from 0 to 25.5 dBm in 0.1 dB steps.rw Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.5 |
pdnAdslPsdConfAturMaxNomAtpRepresents the Maximum nominal aggregate transmit power for the ATU-R. The values range from 0 to 25.5 dBm in 0.1 dB steps.rw Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.6 |
pdnAdslPsdConfAtucMaxRxPwrRepresents the maximum upstream aggregate receive power over a set of subcarriers (in dBm). The ATU-C shall request an upstream power cutback such that the upstream aggregate receive power over that set of subcarriers is at or below the configured maximum value. It ranges from -25.5 to 25.5 dBm, with 0.1 dB steps. The value 2048 is a special value and indicates that no Upstream Maximum Aggregate Receive Power limit is to be applied (i.e., the maximum value is infinite).rw Integer32(-255..255 | 2048) UNITS "tenth dBm" .1.3.6.1.4.1.1795.2.24.2.6.24.1.4.1.7 |
pdnAdslCarMaskTableThis table contains a list of subcarriers that are to be masked (i.e. not transmitted). Subcarriers that are not entries in this table are not masked. SEQUENCE OF PdnAdslCarMaskEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.5 |
pdnAdslCarMaskEntryEach entry represents a specific subcarrier that is masked for a particular profile. PdnAdslCarMaskEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1 |
pdnAdslCarMaskProfileNameThis object identifies a row in the pdnAdslCarMaskTable based on a profile name. SnmpAdminString .1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.1 |
pdnAdslCarMaskSubCarrierIndexThis object identifies a row in the pdnAdslCarMaskTable based on subcarrier that is being masked. The subcarrier index ranges from 0 to (NSCds-1 or NSCus-1 (NSC is Number of Subcarriers) as specified in G.997.1 where NSCds is the higher subcarrier that can be transmitted in the downstream direction and NSCus is the higher subcarrier that can be transmitted in the upstream direction. Please refer to the corresponding ITU recommendation for specific values of NSCds and NSCus. The `ADSL Values for NSC' comment above lists those recommendations. Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.2 |
pdnAdslCarMaskRowStatusThis object is used to create a new row or delete an existing row in this table. A row is activated by setting this object to active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.3 |
pdnAdslCarMaskSubCarrierStatusThis object provides a clear indication that the subcarrier is masked.ro Enumeration .1.3.6.1.4.1.1795.2.24.2.6.24.1.5.1.4 |
pdnAdslLineStatusTableThis table contains current line status measurements. SEQUENCE OF PdnAdslLineStatusEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.6 |
pdnAdslLineStatusEntryEach entry represents an interface. i.e. a row in the ifTable. PdnAdslLineStatusEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1 |
pdnAdslLineStatusAtucLineAtnThe measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all subcarriers during diagnostics mode and initialization. The value 2048 is a special value and indicates the line attenuation is out of the range to be represented.ro Unsigned32(0..1270 | 2048) UNITS "tenth dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.1 |
pdnAdslLineStatusAturLineAtnThe measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all subcarriers during diagnostics mode and initialization. The value 2048 is a special value and indicates the line attenuation is out of the range to be represented.ro Unsigned32(0..1270 | 2048) UNITS "tenth dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.2 |
pdnAdslLineStatusAtucSignalAtnThe measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all subcarriers during showtime. The value 2048 is a special value and indicates the line attenuation is out of the range to be represented.ro Unsigned32(0..1270 | 2048) UNITS "tenth dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.3 |
pdnAdslLineStatusAturSignalAtnThe measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all subcarriers during showtime. The value 2048 is a special value and indicates the line attenuation is out of the range to be represented.ro Unsigned32(0..1270 | 2048) UNITS "tenth dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.4 |
pdnAdslLineStatusAtucSnrMgnThe upstream signal-to-noise ratio margin is the increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all upstream bearer channels. The value 2048 is a special value and indicates the parameter is out of range to be represented.ro Integer32(-640..630 | 2048) UNITS "tenth dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.5 |
pdnAdslLineStatusAturSnrMgnThe downstream signal-to-noise ratio margin is the increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all upstream bearer channels. The value 2048 is a special value and indicates the parameter is out of range to be represented.ro Integer32(-640..630 | 2048) UNITS "tenth dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.6 |
pdnAdslLineStatusAtucMaxAttainableLineRateThe maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver.ro Gauge32 UNITS "bps" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.7 |
pdnAdslLineStatusAturMaxAttainableLineRateThe maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver.ro Gauge32 UNITS "bps" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.8 |
pdnAdslLineStatusAtucActAtpThe total amount of transmit power delivered by the ATU-C at the U-R reference point, at the instant of the measurement. The value 2048 is a special value and indicates the parameter is out of range to be represented.ro Integer32(-310..310 | 2048) UNITS "tenth dBm" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.9 |
pdnAdslLineStatusAturActAtpThe total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of the measurement. The value 2048 is a special value and indicates the parameter is out of range to be represented.ro Integer32(-310..310 | 2048) UNITS "tenth dBm" .1.3.6.1.4.1.1795.2.24.2.6.24.1.6.1.10 |
pdnAdslLineSubCarStatusTableThis table contains current line status measurements. SEQUENCE OF PdnAdslLineSubCarStatusEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.7 |
pdnAdslLineSubCarStatusEntryEach entry represents an interface. i.e. a row in the ifTable. Some objects in this table are only valid if a loop diagnostic has successfully completed. Those objects will return a noSuchName for a Get or Get Next operation if no loop diagnostic has completed. PdnAdslLineSubCarStatusEntry .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1 |
pdnAdslLineCarrierIndexIdentifies a row in the table based on a subcarrier. The subcarrier index ranges from 0 to (NSCds-1 or NSCus-1 (NSC is Number of Subcarriers) as specified in G.997.1 where NSCds is the higher subcarrier that can be transmitted in the downstream direction and NSCus is the higher subcarrier that can be transmitted in the upstream direction. Please refer to the corresponding ITU recommendation for specific values of NSCds and NSCus. The `ADSL Values for NSC' comment above lists those recommendations. Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.1 |
pdnAdslLineSubCarAtucHlinPsThe downstream linear representation, Hlin(f), of the Channel Characteristics Function, H(f). This value is only available after a loop diagnostic procedure. The special value -32768 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of the range to be represented.ro Integer32(-32768 | -32767..32767) .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.2 |
pdnAdslLineSubCarAturHlinPsThe upstream linear representation, Hlin(f), of the Channel Characteristics Function, H(f). This value is only available after a loop diagnostic procedure. The special value -32768 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of the range to be represented.ro Integer32(-32768 | -32767..32767) .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.3 |
pdnAdslLineSubCarAtucHlogMtThe number of symbols used to measure downstream H(f) logarithmic measurement values. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to generate the associate parameter. It should correspond to the value specified in the recommendation (e.g. the number of symbols in 1 s. time interval for G.992.3).ro Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.4 |
pdnAdslLineSubCarAturHlogMtThe number of symbols used to measure downstream H(f) logarithmic measurement values. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to generate the associate parameter. It should correspond to the value specified in the recommendation (e.g. the number of symbols in 1 s. time interval for G.992.3).ro Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.5 |
pdnAdslLineSubCarAtucQlnPsDownstream Quiet Line Noise. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise power Spectral Density (PSD) is out of the range to be represented.ro Unsigned32(0..254 | 255) UNITS "dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.6 |
pdnAdslLineSubCarAturQlnPsUpstream Quiet Line Noise. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise power spectral density (PSD) is out of the range to be represented.ro Unsigned32(0..254 | 255) UNITS "dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.7 |
pdnAdslLineSubCarAtucSnrPsDownstream Signal-to-Noise Ratio. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise power spectral density (PSD) is out of the range to be represented.ro Unsigned32(0..254 | 255 ) UNITS "dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.8 |
pdnAdslLineSubCarAturSnrPsUpstream Signal-to-Noise Ratio. The special value 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise power spectral density (PSD) is out of the range to be represented.ro Unsigned32(0..254 | 255 ) UNITS "dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.9 |
pdnAdslLineSubCarAtucBitsPsDownstream bits allocation.ro Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.10 |
pdnAdslLineSubCarAturBitsPsUpstream bits allocation.ro Unsigned32 .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.11 |
pdnAdslLineSubCarAtucHlogPsThe downstream logarithmic representation, Hlog(f), of the Channel Characteristics function, H(f), providing magnitude values. The special value 1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of the range to be represented.ro Unsigned32(0..1022 | 1023) UNITS "dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.12 |
pdnAdslLineSubCarAturHlogPsThe upstream logarithmic representation, Hlog(f), of the Channel Characteristics function, H(f), providing magnitude values. The special value 1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of the range to be represented.ro Unsigned32(0..1022 | 1023) UNITS "dB" .1.3.6.1.4.1.1795.2.24.2.6.24.1.7.1.13 |
pdnAdslLineExtAFNs OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.2 |
pdnAdslLineExtConformance OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.3 |
pdnAdslLineExtCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.3.1 |
pdnAdslLineExtMIBComplianceThe compliance statement for pdnAdslLineMIB entities which implement the pdnAdslLineMIB. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.1.1 |
pdnAdslLineExtGroups OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.3.2 |
pdnAdslLineExtObjGroups OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1 |
pdnAdslLineExtGroupA collection of objects providing extended configuration information about an ADSL Line. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.1 |
pdnAdslLineSpectrumGroupA collection of objects providing transmission spectrum and power spectral density related profiles. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.2 |
pdnAdslModeSpecificPsdGroupA collection of objects providing a mapping from an entry into the ADSL Line Spectrum Table to a profile defining a specific set of power spectral density settings. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.3 |
pdnAdslPsdGroupA collection of objects providing specific power spectral density settings based on a named profile. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.4 |
pdnAdslCarMaskGroupA collection of objects providing the ability for an administrator to mask out specific subcarriers in the downstream or the upstream direction. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.5 |
pdnAdslLineL2AtprtGroupTotal maximum aggregate transmit power reduction in L2. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.6 |
pdnAdslLineStatusLineAtnGroupLine attenuation during diagnostic mode and initialization. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.7 |
pdnAdslLineStatusSignalAtnGroupLine attenuation during showtime. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.8 |
pdnAdslLineStatusSnrMgnGroupSNR margin ratio. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.9 |
pdnAdslLineStatusMaxattainableLineRateGroupCurrent maximum attainable net data rate. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.10 |
pdnAdslLineStatusActAtpGroupActual aggregate transmit power. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.11 |
pdnAdslLineSubCarStatusHlinGroupLinear representation of the Channel Characteristics function for a subcarrier on a line. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.12 |
pdnAdslLineSubCarStatusHlogMtGroupLogarithmic measurement time of the Channel Characteristics function for a subcarrier on a line. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.13 |
pdnAdslLineSubCarStatusQlnGroupQuiet Line Noise for a subcarrier on a line. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.14 |
pdnAdslLineSubCarStatusSnrGroupSignal-to-Noise Ratio for a subcarrier on a line. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.15 |
pdnAdslLineSubCarStatusBitsGroupBits allocation for a subcarrier on a line. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.16 |
pdnAdslLineSubCarStatusHlogGroupLogarithmic representation of the Channel Characteristics function for a subcarrier on a line. Unknown .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.1.17 |
pdnAdslLineExtAfnGroups OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.2 |
pdnAdslLineExtNtfyGroups OBJECT IDENTIFIER .1.3.6.1.4.1.1795.2.24.2.6.24.3.2.3 |