PAIRGAIN-APS-MIB
AI MIB Summary
The PAIRGAIN-APS-MIB facilitates the monitoring and management of PairGain Avidia System linear APS1+1 redundancy units, specifically tracking active/standby interface states, protection switching events, and hardware health metrics for T1/E1 line interfaces.
The module defines the PairGain Proprietary linear APS1+1 MIB used in the Avidia System
Main OID:
pgAps.1.3.6.1.4.1.927.1.9.12.1
31
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
31 total| Object Name |
|---|
pgApsThe module defines the PairGain Proprietary linear APS1+1 MIB
used in the Avidia System MODULE-IDENTITY .1.3.6.1.4.1.927.1.9.12.1 |
SNMPv2-SMIThe module defines the PairGain Proprietary linear APS1+1 MIB
used in the Avidia System Unknown .1.3.6.1.4.1.927.1.9.12.1 |
pgApsMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.927.1.9.12.1.0 |
pgApsTrapSwitchOverIf pgApsTrapEnable is enabled, then pgApsTrapSwitchOver is sent when
the APS switches from the working channel to the protection channel or
from the protection channel to the working channel. This occurs when
the value of pgApsWorkingNumSwitchOvers or pgApsProtNumSwitchOvers
increments. NOTIFICATION-TYPE .1.3.6.1.4.1.927.1.9.12.1.0.1 |
pgApsMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.927.1.9.12.1.1 |
pgApsConfigTableThis table provides the Automatic Protection Switch
Mode Configuration for Linear 1+1 mode APS SEQUENCE OF PgApsConfigEntry .1.3.6.1.4.1.927.1.9.12.1.1.1 |
pgApsConfigEntryEntries in the pgApsConfigTable table. PgApsConfigEntry .1.3.6.1.4.1.927.1.9.12.1.1.1.1 |
pgApsIndexAPS entries are slot based.
The index uses the slot number of the card.
pgApsIndex (slot number) identifies the APS 1+1 entry that
represents the two APS 1+1 channels.ro INTEGER .1.3.6.1.4.1.927.1.9.12.1.1.1.1.1 |
pgApsEnableEnable (1) or disables (2) the APS feature. The default is
disabled (2).rw Enumeration .1.3.6.1.4.1.927.1.9.12.1.1.1.1.2 |
pgApsTrapEnableEnables (1) or disables (2) the sending of the trap whenever an
APS switch occurs. The default is disabled (2).rw Enumeration .1.3.6.1.4.1.927.1.9.12.1.1.1.1.3 |
pgApsWorkChanIfIndexThe ifIndex of the 1+1 APS configuration working channel.ro Integer32 .1.3.6.1.4.1.927.1.9.12.1.1.1.1.4 |
pgApsProtChanIfIndexThe ifIndex of the 1+1 APS configuration protection channel.ro Integer32 .1.3.6.1.4.1.927.1.9.12.1.1.1.1.5 |
pgApsConfigModenonRevertive(1) : Default. non-Revertive mode as defined in
GR-253
nonRevertiveAuto(2) : PairGain proprietary mode that switches from
the working channel to the protection
channel upon a signal failure (SF) or signal
degradation (SD) condition. After the
proprietary PairGain wait to switch time has
elapsed, the channel can switch from the
protection channel to the working channel
upon an SF or SD condition. Thus the name
'non-revertive, auto switching'
revertive(3) : Revertive switching mode as defined in GR-253rw Enumeration .1.3.6.1.4.1.927.1.9.12.1.1.1.1.6 |
pgApsConfigSigDegradeThreshThe Bit Error Rate threshold at which the APS declares that the
currently selected signal has degraded.
The value is the minus power of 10. For example, a value of 7
represents 10e-7.ro INTEGER .1.3.6.1.4.1.927.1.9.12.1.1.1.1.7 |
pgApsConfigWaitToRevertThis object is only used during 'revertive' switching mode:
If the switch has occurred and the error condition has disappeared,
then number of seconds specified in this MIB object must elapse
before the APS will switch back to the normal mode.
The valid range is 300 to 720 seconds (5-12 minutes).
The default is 300 seconds (5 minutes).rw INTEGER .1.3.6.1.4.1.927.1.9.12.1.1.1.1.8 |
pgApsSwitchCommandSends a local switch command. For example,
a command could be Manual switch from normal to protection, or
Forced switch from normal to protection.
The command format is defined as follows:
The pgApsSwitchCommand consists of two 16-bit portions.
The high order word contains the command.
The low order word contains the destination channel
(either working or protection.)
The commands contained in the high order word are as follows:
Value Command
===== =======
0 Clear all switch commands for the specified channel.
1 Lockout the working channel from switching to the protection
channel.
2 Force switch from the working channel to the protection
channel.
3 Force switch from the protection channel to the working
channel.
4 Manual switch from the working to the protection. This
will not work if SD or SF is in effect on the protection
channel.
5 Manual switch from the protection to the working channel.
This will not work if SD or SF is active on the working
channel.rw Integer32 .1.3.6.1.4.1.927.1.9.12.1.1.1.1.9 |
pgApsStatusTableThis table provides the status for each 1+1 APS entry. SEQUENCE OF PgApsStatusEntry .1.3.6.1.4.1.927.1.9.12.1.1.2 |
pgApsStatusEntryStatus entry for each 1+1 APS. PgApsStatusEntry .1.3.6.1.4.1.927.1.9.12.1.1.2.1 |
pgApsStatusK1K2RxThe value of the K1 K2 SONET overhead bytes received.ro PgApsK1K2 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.1 |
pgApsStatusK1K2TxThe value of the K1 K2 SONET overhead bytes transmitted.ro PgApsK1K2 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.2 |
pgApsStatusCurrentThe current switch status.
0 means the working channel selected
1 means protection channel selected
The default is the working channel (0).ro Byte .1.3.6.1.4.1.927.1.9.12.1.1.2.1.3 |
pgApsWorkChanStatusBit 0 set means that this channel is locked out and will not be switched.
Bit 1 set means that the SD state is in effect on this channel
Bit 2 set means that the SF state is in effect on this channelro Bits .1.3.6.1.4.1.927.1.9.12.1.1.2.1.4 |
pgApsWorkChanLastSwitchTime stamp of the last time the working channel switched
to the protection channel.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.927.1.9.12.1.1.2.1.5 |
pgApsWorkChanSDsRunning count of the number of SD conditions for the working
channel that the driver detected.ro Counter32 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.6 |
pgApsWorkChanSFsRunning count of the number of SF conditions for the working
channel that the driver detected.ro Counter32 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.7 |
pgApsWorkNumSwitchOversThe number of times the working channel has switched to the protection channel.ro Counter32 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.8 |
pgApsProtChanStatusThe protection channel status:
Bit 0 set means that the protection channel is locked out and
will not be switched.
Bit 1 set means that the SD state is in effect on the protection
channel.
Bit 2 set means that the SF state is in effect on the protection
channel.ro Bits .1.3.6.1.4.1.927.1.9.12.1.1.2.1.9 |
pgApsProtChanLastSwitchTime stamp of the last time the Protection channel switched
to the working channel.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.927.1.9.12.1.1.2.1.10 |
pgApsProtChanSDsRunning count of the number of SD conditions for the protection
channel that the driver detected.ro Counter32 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.11 |
pgApsProtChanSFsRunning count of the number of SF conditions for the protection
channel that the driver detected.ro Counter32 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.12 |
pgApsProtNumSwitchOversThe number of times the protection channel switched to the
working channel.ro Counter32 .1.3.6.1.4.1.927.1.9.12.1.1.2.1.13 |