MITEL-LOGICAL-MIB
The MITEL Logical MIB module.
Main OID:
mitelRouterLogicalGroup.1.3.6.1.4.1.1027.4.8.1.4
41
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
41 total| Object Name |
|---|
mitel OBJECT IDENTIFIER .1.3.6.1.4.1.1027 |
mitelIdentification OBJECT IDENTIFIER .1.3.6.1.4.1.1027.1 |
mitelIdCallServers OBJECT IDENTIFIER .1.3.6.1.4.1.1027.1.2 |
mitelIdCsIpera1000 OBJECT IDENTIFIER .1.3.6.1.4.1.1027.1.2.4 |
mitelIpera1000NotificationsNotifications for Call Server IPera 1000. Unknown .1.3.6.1.4.1.1027.1.2.4.0 |
mitelWanRetryThresholdThe mitelWanRetryThreshold trap is generated by the router whenever the maximum number of retries have been exhausted when attempting to contact a remote site on a specific serial interface. The mitelLogicalTblIndex will provided in the variable bindings for this trap type. NOTIFICATION-TYPE .1.3.6.1.4.1.1027.1.2.4.0.403 |
mitelProprietary OBJECT IDENTIFIER .1.3.6.1.4.1.1027.4 |
mitelPropIpNetworking OBJECT IDENTIFIER .1.3.6.1.4.1.1027.4.8 |
mitelIpNetRouter OBJECT IDENTIFIER .1.3.6.1.4.1.1027.4.8.1 |
mitelRouterLogicalGroupThe MITEL Logical MIB module. MODULE-IDENTITY .1.3.6.1.4.1.1027.4.8.1.4 |
mitelLogGrpLogicalTableA table containing information about logical LAN destinations. SEQUENCE OF MitelLogGrpLogicalEntry .1.3.6.1.4.1.1027.4.8.1.4.1 |
mitelLogGrpLogicalEntryEach entry of this table contains information about a specific logical interface to a local area network. Each logical LAN can support routing functions, these are considered virtual interfaces. The logical LAN can be permanently attached to a physical port (LAN or WAN) or it can float among available physical resources (WAN's only). MitelLogGrpLogicalEntry .1.3.6.1.4.1.1027.4.8.1.4.1.1 |
mitelLogicalTblIndexThis object identifies the instance of this entry in the table.ro Integer32 .1.3.6.1.4.1.1027.4.8.1.4.1.1.1 |
mitelLogicalTblDestNameThe Ascii string associated with this logical destination LAN. Default is Net N (N is mitelLogicalTblIndex).rw DisplayString .1.3.6.1.4.1.1027.4.8.1.4.1.1.2 |
mitelLogicalTblTypeThis object determines whether this network interface is locally connected to a LAN or is connected to a LAN via a WAN. If this object is set to local(1) then this interface is associated with one of the physical LAN interfaces via the ifIndex. If this object indicates remote(2) then this network is reachable through a wide area network (WAN) as described in mitelLogGrpLogicalWanTable.ro Enumeration .1.3.6.1.4.1.1027.4.8.1.4.1.1.3 |
mitelLogicalTblAdminStatusThe current desired state of this sub-layer. Default is down.rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.1.1.4 |
mitelLogGrpLogicalWanTableA table containing configuration parameters for wide area network connections to logical LAN destinations that are accessible via interfaces. Each entry is logically tied to a logical LAN destination entry via mitelLogicalTblIndex. SEQUENCE OF MitelLogGrpLogicalWanEntry .1.3.6.1.4.1.1027.4.8.1.4.2 |
mitelLogGrpLogicalWanEntryEach entry of this table contains information about a specific logical interface to a REMOTELY connected local area network. The instance of mitelLogicalTblIndex used to index into this table is the same instance value used to index into the grLogicalTable. MitelLogGrpLogicalWanEntry .1.3.6.1.4.1.1027.4.8.1.4.2.1 |
mitelLogWanTblCmprsnThis object indicates whether or not this interface is to perform data compression. Default is none.rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.2.1.1 |
mitelLogWanTblCmprsnStatusThis object describes the type of compression used on this destination.ro Enumeration .1.3.6.1.4.1.1027.4.8.1.4.2.1.2 |
mitelLogWanTblEncryptnThis object describes whether or not PPP encryption is proposed to the peer. Default is disabled.rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.2.1.3 |
mitelLogWanTblBackupOvrflowThis object determines if this interface is to attempt to bring up another link to the same destination if the traffic over the primary link exceeds a pre-determined threshold, in the case of overflow(3). Otherwise, if backup(2) is selected the interface will bring up an alternate link to the same destination in the case that the primary link fails. Default is disabled(1).rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.2.1.4 |
mitelLogWanTblThshldThis object determines the transmit threshold which when exceeded will cause an attempt to bring up another path. The returned value of this object has no meaning when threshold overflow is not enabled. Default is 80.rw INTEGER .1.3.6.1.4.1.1027.4.8.1.4.2.1.5 |
mitelLogWanTblConnTimerWhen threshold overflow is enabled this object determines the amount of time in seconds that the average threshold must be exceeded (or below) before another link is established (or disconnected). Default is 30.rw INTEGER .1.3.6.1.4.1.1027.4.8.1.4.2.1.6 |
mitelLogWanTblDiscTimerThe time a non-permanent link will remain connected without traffic. Default is 30.rw INTEGER .1.3.6.1.4.1.1027.4.8.1.4.2.1.7 |
mitelLogWanTblProtocolTypeThe protocol type that this destination is over. Default is ppp.rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.2.1.8 |
mitelLogGrpLogicalWanPortTableThis configuration table identifies the characteristics of each potential transportation pipe to a remote site. Each entry in this table is associated with an entry in the grLogWanTable via its mitelLogicalTblIndex. Multiple entries can be associated with a single entry in the mitelLogGrpLogicalWanTable. SEQUENCE OF MitelLogGrpLogicalWanPortEntry .1.3.6.1.4.1.1027.4.8.1.4.3 |
mitelLogGrpLogicalWanPortEntryEach entry of this table contains information about a single WAN resource used by a logical interface to a remote local area network. The instance of mitelLogicalTblIndex used to index into this table is the same instance value used to index into the mitelLogicalTable. Multiple entries in this table having the same mitelLogicalTblIndex usually indicates backup or multi-linking functionality. MitelLogGrpLogicalWanPortEntry .1.3.6.1.4.1.1027.4.8.1.4.3.1 |
mitelLogWanPortTblIndexIdentifies the port index associated with this entry.ro Integer32 .1.3.6.1.4.1.1027.4.8.1.4.3.1.1 |
mitelLogWanPortTblWanTypeIndicates whether or not this link is to be used as a permanent or ondemand link. Default is ondemandrw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.3.1.2 |
mitelLogWanPortTblTransTypeThe transport type that this destination is over. Default is HDLC.rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.3.1.3 |
mitelLogWanPortTblRetryDetermines the retry count for dial up WAN circuits. Default is 10.rw INTEGER .1.3.6.1.4.1.1027.4.8.1.4.3.1.4 |
mitelLogWanPortTblRetryPeriodDetermines the retry period in seconds for dial up WAN circuits. Default is 10 seconds.rw INTEGER .1.3.6.1.4.1.1027.4.8.1.4.3.1.5 |
mitelLogWanPortTblPrependIndicates in most cases an Ascii string that will be prepended to the destination address. Default is NULL.rw OCTET STRING .1.3.6.1.4.1.1027.4.8.1.4.3.1.6 |
mitelLogWanPortTblDestAddrIndicates the destination address that this interface will call (ie: phone number). Default is NULL.rw DisplayString .1.3.6.1.4.1.1027.4.8.1.4.3.1.7 |
mitelLogWanPortTblNextDestAddrIndicates the next destination address that this interface will call (ie: phone number). Default is NULL.rw DisplayString .1.3.6.1.4.1.1027.4.8.1.4.3.1.8 |
mitelLogWanPortTblChIdThis object is a unique identifier for this network channel. e.g. DLCI for frame-relay. The value must be within the defined range or if not used the DEFAULT value should be 0.rw INTEGER .1.3.6.1.4.1.1027.4.8.1.4.3.1.9 |
mitelLogWanPortTblDialbackEnables/disables dialback option. If enabled the system will drop the link and then dial the user back using the configured dial string or a dial string reported from an authentication server. Default is disabled.rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.3.1.10 |
mitelLogWanPortTblAdminStatusThe current desired state of this sub-layer. Default is down.rw Enumeration .1.3.6.1.4.1.1027.4.8.1.4.3.1.11 |
mitelLogWanPortTblOperStatusThe current active state of this sub-layer.ro Enumeration .1.3.6.1.4.1.1027.4.8.1.4.3.1.12 |
mitelLogWanPortTblStatusThe current status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1027.4.8.1.4.3.1.13 |