LUM-WDM-MIB
AI MIB Summary
The LUM-WDM-MIB module facilitates the monitoring and management of WDM trunk interfaces, passive optical interfaces, and associated protection groups within optical transport networks. It provides granular visibility into interface status, signal parameters, and protection switching states to ensure the integrity of wavelength division multiplexing infrastructure.
The WDM trunk interface and protection group MIB.
- General
- WDM trunk interfaces
- WDM passive interfaces
- Protection groups
Main OID:
lumWdmMIBModule.1.3.6.1.4.1.8708.1.1.6
418
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
418 total| Object Name |
|---|
lumWdmMIBModuleThe WDM trunk interface and protection group MIB.
- General
- WDM trunk interfaces
- WDM passive interfaces
- Protection groups MODULE-IDENTITY .1.3.6.1.4.1.8708.1.1.6 |
lumWdmConfs OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.1 |
lumWdmGroups OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.1.1 |
lumWdmCompl OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.1.2 |
lumWdmMinimalGroups OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.1.3 |
lumWdmMinimalCompl OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.1.4 |
lumWdmMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2 |
wdmGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.1 |
wdmGeneralTestAndIncrProtection against simultaneous access from
multiple managers. See SNMPv2-TC.rw TestAndIncr (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.1.1 |
wdmGeneralMibSpecVersionThe MIB specification version.
tbd: persistent?rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.1.2 |
wdmGeneralMibImplVersionThe MIB implementation version.
tbd: persistent?rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.1.3 |
wdmGeneralLastChangeTimeThe time when the configuration of the MIB was
last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.1.4 |
wdmGeneralStateLastChangeTimeThe time when the state of the MIB was last
changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.1.5 |
wdmGeneralWdmIfTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.6 |
wdmGeneralWdmPassiveIfTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.7 |
wdmGeneralWdmProtTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.8 |
wdmGeneralWdmVc4TableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.9 |
wdmGeneralWdmRemoteProtTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.10 |
wdmGeneralWdmCtrlChannelTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.11 |
wdmGeneralWdmCtrlGroupTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.12 |
wdmGeneralWdmSubChannelTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.13 |
wdmGeneralWdmDelayCompPGTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.14 |
wdmGeneralWdmDelayCompLinkTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.15 |
wdmGeneralWdmMeanChannelPowerControlTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.16 |
wdmGeneralWdmMeanChannelPowerControlGlobalTableSizeSize of tablero Unsigned32 .1.3.6.1.4.1.8708.2.4.2.1.17 |
wdmIfList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.2 |
wdmIfTableThe interface list. SEQUENCE OF WdmIfEntry .1.3.6.1.4.1.8708.2.4.2.2.1 |
wdmIfEntryAn entry in the interface list. WdmIfEntry .1.3.6.1.4.1.8708.2.4.2.2.1.1 |
wdmIfIndexAn arbitrary index assigned to each if entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.1 |
wdmIfNameThe management name of the interface, for example
'wdm:1:2:1'.ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.2.1.1.2 |
wdmIfDescrUser configurable label.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.2.1.1.3 |
wdmIfSubrackThe number of the subrack where the interface
is located.ro SubrackNumber .1.3.6.1.4.1.8708.2.4.2.2.1.1.4 |
wdmIfSlotThe number of the slot where the interface is
located.ro SlotNumber .1.3.6.1.4.1.8708.2.4.2.2.1.1.5 |
wdmIfTxPortThe number of the port where the interface is
located.ro PortNumber .1.3.6.1.4.1.8708.2.4.2.2.1.1.6 |
wdmIfInvPhysIndexOrZeroThe row in the invPhysTable for this interface.
Set to 0 if not known.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.7 |
wdmIfTxLambdaThe transmitted frequency given in hundreds of
GHz (0.01 GHz).ro LambdaFrequency .1.3.6.1.4.1.8708.2.4.2.2.1.1.8 |
wdmIfHighSpeedMinThe minimum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n' then
the speed of the interface is somewhere in the
range of 'n-500,000' to 'n+499,999'.ro Gauge32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.9 |
wdmIfHighSpeedMaxThe maximum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n' then
the speed of the interface is somewhere in the
range of 'n-500,000' to 'n+499,999'.ro Gauge32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.10 |
wdmIfPowerLevelThe received power level in units of 0.1 dBm.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.11 |
wdmIfPowerLevelHighThresholdThe upper threshold for received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary.rw Integer32 (-380..-60) .1.3.6.1.4.1.8708.2.4.2.2.1.1.12 |
wdmIfPowerLevelLowThresholdThe lower threshold for received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary.rw Integer32 (-380..-60) .1.3.6.1.4.1.8708.2.4.2.2.1.1.13 |
wdmIfLaserTempThe pre-set laser temperature in units of
0.1 degrees centigrade.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.14 |
wdmIfLaserTempOffsetThe current offset from the pre-set temperature
in units of 0.1 degrees centigrade.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.15 |
wdmIfLaserTempOffsetThresholdThe absolute value of the offset for the LTL
and LTH alarms in units of 0.1 degrees centigrade.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.16 |
wdmIfLaserModeThe administrative state of the TX-side laser.
on - The laser is turned on.
als - Automatic Laser Shutdown/Turn-Off
when lossOfSignal is detected on the RX side of
the trunk interface.
Note, als is not available for MBA boards.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.17 |
wdmIfLaserStatusThe operational state of the TX-side laser.
off - The laser is turned off.
on - The laser is turned on.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.18 |
wdmIfAdminStatusThe administrative state for the interface.
down - The interface is de-activated.
service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-configuration. When service is concluded
adminStatus should be set to 'up' again. Note that
there is no difference between 'up' and 'service',
if no alarms can be raised from this object.
up - The interface will be activated when
available. Alarms are not suppressed.
This attribute can be written via SNMP.rw BoardOrInterfaceAdminStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.19 |
wdmIfOperStatusThe operational state for the interface.
notPresent - The interface is not available.
down - The interface is de-activated or there are
faults preventing its transition to the 'up' state.
up - The interface is active.ro BoardOrInterfaceOperStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.20 |
wdmIfLossOfSignalLoss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW indication.
D(e-activation): Inactive loss of signal HW
indication.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.21 |
wdmIfReceivedPowerHighReceived power level is too high.
Applicable for all signal formats.
A: The received power level exceeds the
the built-in overload threshold.
D: The received power level is 0.5 dB below the
overload threshold.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.22 |
wdmIfReceivedPowerLowReceived power level low threshold exceeded.
Applicable for all signal formats.
A: The received power level is below the
associated threshold.
D: The received power level is 0.5 dB above the
threshold.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.23 |
wdmIfLaserBiasHighLaser bias high threshold exceeded.
A: The laser bias current exceeds the associated
threshold.
D: The laser bias current is 0.5 mA below the
associated threshold.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.24 |
wdmIfErroredSecondsNote: This attribute is deprecated!
Errored seconds (ES) threshold exceeded.
A: The number of errored seconds during a period
exceeds the associated threshold.
D: At the start of a new period.rodeprecated FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.25 |
wdmIfSeverelyErroredSecondsNote: This attribute is deprecated!
Severely errored seconds (SES) threshold exceeded.
A: The number of severely errored seconds during
a period exceeds the associated threshold.
D: At the start of a new period.rodeprecated FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.26 |
wdmIfBackgroundBlockErrorsNote: This attribute is deprecated!
Background block errors (BBE) threshold exceeded.
A: The number of errors during a period
exceeds the associated threshold.
D: At the start of a new period.rodeprecated FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.27 |
wdmIfUnavailableSecondsNote: This attribute is deprecated!
Unavailable seconds (UAS) threshold exceeded.
A: The number of unavailable seconds during a
period exceeds the associated threshold.
D: At the start of a new period.rodeprecated FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.28 |
wdmIfForwardDefectIndicationForward defect indication.
Applicable for all signal formats; detected at
WDM level. This alarm suppresses the
corresponding SDH/Sonet alarm.
A: Forward defect indication (in wrapper) active.
D: Forward defect indication inactive.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.29 |
wdmIfBackwardDefectIndicationBackward defect indication.
Applicable for all signal formats; detected at
WDM level. This alarm suppresses the
corresponding SDH/Sonet alarm.
A: Backward defect indication (in wrapper) active.
D: Backward defect indication inactive.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.30 |
wdmIfLossOfFrameLoss of frame.
Applicable for SDH/Sonet signal formats.
A: SDH frame can not be located.
D: SDH frame is located.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.31 |
wdmIfAlarmIndicationSignalAlarm indication signal.
Applicable for SDH/Sonet signal formats.
For other proprietary formats, e.g. for
the tpDDGbE line signal, a similar
functionality is emulated.
A: An 'all ones' SDH/Sonet signal is detected.
D: SDH/Sonet signal recovered.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.32 |
wdmIfRemoteDefectIndicationRemote defect indication.
Applicable for SDH/Sonet signal formats.
A: RDI indication (in SDH/Sonet frame) active.
D: RDI indication inactive.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.33 |
wdmIfLossOfSyncLoss of sync (GbE).
Applicable for GbE signal formats.
A: GbE 'frame' can not be located.
D: GbE 'frame' is located.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.34 |
wdmIfLossOfForwardingErrorCorrectionLoss of forwarding error correction (FEC).
Applicable for all signal formats.
A: The interface is unable to perform forwarding
error correction.
D: The interface is able to perform FEC.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.35 |
wdmIfLaserTempHighLaser temperature high threshold exceeded.
A: The temperature exceeds the associated
threshold.
D: Temperature is 0.5 degrees centigrade below
the associated threshold.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.36 |
wdmIfLaserTempLowLaser temperatur low threshold exceeded.
The temperature exceeds the associated threshold.
A: The temperature exceeds the associated
threshold.
D: Temperature is 0.5 degrees centigrade above the
associated threshold.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.37 |
wdmIfRxPortThe number of the port where the interface is
located.ro PortNumber .1.3.6.1.4.1.8708.2.4.2.2.1.1.38 |
wdmIfBitrateMismatchBitrate mismatch (Other).
Applicable for other signal formats.
A: The interface is unable to lock to the
inserted signal.
D: The interface is able to lock to the inserted
signal.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.39 |
wdmIfLaserBiasMeasures laser bias current value in tenths of
mA (0.1 mA).ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.40 |
wdmIfLaserBiasThresholdSets the threshold for the laser bias alarm.
in percentage relative to the value set during
production. The preset value is 100%.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.41 |
wdmIfLossOfSignalThresholdThe upper threshold received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary.rw Integer32 (-380..-220) .1.3.6.1.4.1.8708.2.4.2.2.1.1.42 |
wdmIfJ0PathTraceThe received J0 path trace string.
Applicable for SDH/Sonet signal formats.rodeprecated OCTET STRING .1.3.6.1.4.1.8708.2.4.2.2.1.1.44 |
wdmIfInbandModeThe administrative state the in-band management
channel of the WDM interface.
down - The management channel is disabled.
up - The management channel is in use.rwdeprecated Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.45 |
wdmIfInbandStatusThe operational state the in-band management
channel of the WDM interface.
down - The management channel is disabled.
up - The management channel is in use.rodeprecated Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.46 |
wdmIfExpectedTxLambdaThe expected frequency or wavelength.
ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.
The semantic of this attribute is different depending
on the laser frequency type.
Fixed frequency: 'Unexpected frequency' is raised if
the expected frequency is not equal to actual
frequency.
Tunable frequency: The attribute is used to tune the
laser frequency. 'No frequency set' is raised if no
frequency has been selected.
This attribute can be written via SNMP.rw LambdaFrequency .1.3.6.1.4.1.8708.2.4.2.2.1.1.47 |
wdmIfForwardingErrorCorrectionModeThe administrative state of the forwarding error
correction function.
disabled - FEC is disabled.
enabled - FEC is activated.
auto - autonegotiation is used to enable or disable
FEC. Note, auto is not available for all
boards.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.48 |
wdmIfUnexpectedTxLambdaThe actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured frequency does not match the
actual frequency.
D: The configured frequency matches the actual
frequency.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.49 |
wdmIfTraceIntrusionModeIndicates whether the trace identifier should be
inserted in the transmitted signal.
disabled - The trace identifier is taken from
the received signal if possible.
enabled - The trace identifier set is inserted in
the transmitted signal.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.50 |
wdmIfTraceTransmittedThe trace identifier to be transmitted from this
interface.
The identifier length is by default 0 to 15. For
mxp8iiSonet boards the length is 0 to 62.
Set to empty string for default value:
<IP address>:<subrack>:<slot>:<port>
Note that only the last part of the address
is used.rw DisplayString .1.3.6.1.4.1.8708.2.4.2.2.1.1.51 |
wdmIfTraceReceivedThe received trace identifier for this interface.ro DisplayString .1.3.6.1.4.1.8708.2.4.2.2.1.1.52 |
wdmIfTraceExpectedTrace identifier used for matching against
the received trace identifier.
The identifier length is by default 0 to 15. For
mxp8iiSonet boards the length is 0 to 62.rw DisplayString .1.3.6.1.4.1.8708.2.4.2.2.1.1.53 |
wdmIfTraceAlarmModeControls if the trace identifier mismatch alarm
should be raised.
disabled - The alarm is disabled.
enabled - The alarm is raised if expected trace
identifier differs from the received trace
identifier.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.54 |
wdmIfTraceMismatchIndicates if the expected trace identifier
differs from the received trace identifier.
A: The received trace identifier differs from
the expected trace identifier.
D: The identifiers match.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.55 |
wdmIfLaserStatusLastChangeTimeThe time when the laser status was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.2.1.1.56 |
wdmIfSuppressRemoteAlarmsSuppress AIS, FDI and RDI in the alarm list. The
fault status on the port object can, however, be
seen.
disabled - alarms are not suppressed.
enabled - alarms are suppressed.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.57 |
wdmIfSerialNumberMismatchWrong HW unit installed. The link has not been
optimized for this individual, wrong serial number.
Action: The installation optimization procedure must
be run again.
A: The installed board does not match the
installation.
D: The installed board matches the installation.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.58 |
wdmIfOptimizeDecisionThresholdOptimize the threshold for distinguishing between
1s and 0s.
This attribute is of 'action type' - it will always
have the value 'normal'
normal - just a placeholder, is never set by the
user.
run - run the optimization procedure.ro CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.59 |
wdmIfThresholdOptimizationStateState of the optimization procedure
normal - no operation has been started
started - the operation is started
searchingFirstLow - Search for the first value of
the lower flank
searchingSecondLow - Search for the second value of
the lower flank
searchingThirdLow - Search for the third value of
the lower flank
searchingFirstHigh - Search for the first value of
the upper flank
searchingSecondHigh - Search for the second value of
the upper flank
searchingThirdHigh - Search for the third value of
the upper flank
finishedOk - the operation has been
successfully finished
finishedFailed - the operation failed
searchingFrameLow - Search for the frame at the
lower end
searchingFrameHigh - Search for the frame at the
upper end
foundFrame - frame has been found
waitOptimize - wait for HW-optimize procedurero Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.60 |
wdmIfUseHwDefaultDecisionThresholdUse the HW default decision threshold.
This attribute is of 'action type' - it will always
have the value 'normal'
normal - just a placeholder, is never set by the
user.
reset - reset to the default value stored in HW unit.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.61 |
wdmIfFecCorrectedZerosThe number of corrected zeros.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.62 |
wdmIfFecCorrectedOnesThe number of corrected ones.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.63 |
wdmIfOptimizedForSerialNumberThis field contains the serial number of
the transponder unit, for which the decision
threshold is optimized and stored.rw DisplayString .1.3.6.1.4.1.8708.2.4.2.2.1.1.64 |
wdmIfRelativeDecisionThresholdThe 1/0 decision threshold computed at installation.
The threshold is automatically optimized if the
'Continous optimization' functionality is enabled.
Press the 'Optimize' button to manually trigger
the optimization routine once.rw Integer32 (-1000000..1000000) .1.3.6.1.4.1.8708.2.4.2.2.1.1.65 |
wdmIfTrxCodeMismatchThe inserted transceiver does not have a legal
manufacturer code.
A: A transceiver with illegal code is inserted.
D: The transceiver with illegal code is removed.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.66 |
wdmIfTrxBitrateUnavailableThe inserted transceiver does not support the
requested bit rate.
A: A transceiver with other supported bit rate than
the requested bit rate is inserted.
D: The transceiver with the non-requested bit rate is
removed, or the object is reconfigured.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.67 |
wdmIfTrxMissingAn expected transceiver is missing.
A: An expected transceiver is missing.
D: The missing transceiver is inserted.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.68 |
wdmIfTrxClassString that describes the transceiver class.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.2.1.1.69 |
wdmIfLaserTempHighRelativeThresholdThreshold for the Laser Temp High alarm, expressed
as an offset from a pre-set nominal temperature,
in units of 0.1 degrees centigrade.rw Integer32 (-100..100) .1.3.6.1.4.1.8708.2.4.2.2.1.1.70 |
wdmIfLaserTempLowRelativeThresholdThreshold for the Laser Temp Low alarm, expressed
as an offset from a pre-set nominal temperature,
in units of 0.1 degrees centigrade.rw Integer32 (-100..100) .1.3.6.1.4.1.8708.2.4.2.2.1.1.71 |
wdmIfTransmitterFailedThe transceiver HW has detected a failure
in the transmitter part.
A: The transmitter has failed
D: The transmitter is OK againro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.72 |
wdmIfReceiverSensitivityThe lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.73 |
wdmIfPowerLevelLowRelativeThresholdThe lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity, or loss of signal threshold.
- For fixed transceivers it is measured with respect
to the loss threshold.
- For pluggable transceivers (SFP/XFP) it is
measured with respect to the receiver sensitivity.rw Integer32 (-50..100) .1.3.6.1.4.1.8708.2.4.2.2.1.1.74 |
wdmIfIllegalFrequencyThe frequency supported by the transceiver is not
recognized by the system.
A: Invalid or unknown frequency information is
detected in the (pluggable) transceiver or
board production data.
D: The (pluggable) transceiver or board is
replaced.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.75 |
wdmIfLaserForcedOnWhen enabled, the laser is on regardless of whether
there is a client signal or not.
disabled - the laser is only on when there is a
client signal.
enabled - the laser is always on. This is intended
to be used at installation to generate
light on the WDM-side for the QMR board
even if there are not client equipment
available.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.76 |
wdmIfTrafficCombinationSpecifies how different traffic formats can be
combined on different ports on gxp2500, gxp2500Sfp,
fhmxp10g, msMxp10G and msMxp. All combinations
can not be used on all boards.
undefined - no format selected yet
fcGbEx2 - 2 ports can carry either GbE
or Fc, or 1 port can carry 2G
Fc.
dvbEsconx8 - 8 ports can carry either DvB,
Escon, or Escon-LL.
esconx10 - 10 ports can carry Escon.
framedGbEx10 - 10 ports can carry a rate
limited GbE.
esconx6FcGbE - 6 ports can carry Escon,
combined with 1 port carrying
Fc or GbE.
dvbEsconx4FcGbE - 4 ports can carry DvB, Escon,
Escon-LL, combined with 1 port
carrying Fc or GbE.
mixed - All ports can be freely
combined, for experimental
use.
framedGbEx10Vc4 - Like framedGbEx10, but uses
VC4s instead of VC-3
fcx2VcatVc4 - 2 x FC over VCAT VC-4
fc2GVcatVc4 - 2G FC over VCAT VC-4
dvbEsconx8VcatVc4 - Like dvbEsconx8, but uses VCAT
VC-4 instead
mixedVcatVc4 - Like mixed but uses VCAT VC-4
instead
fcGbEx2VcatVc4 - Like fcGbEx2 but uses VCAT
VC-4 instead
gbEx3Stm4Oc12x1Stm1Oc3x3 - 3 ports carry GbE, 1 port can
carry Stm4/Oc12 or Stm1/Oc3, 3 ports
can carry only Stm1/Oc3 (MsMxp)
gbEx1Stm16Oc48x1Stm1Oc3x3 - 1 port carries GbE, 1 port
carries Stm16/Oc48, 3 ports carry
Stm1/Oc3 (MsMxp)
gbESyncEx3Stm4Oc12Stm1Oc3x1 - 3 ports carry synchron GbE, 1
port can carry Stm4/Oc12 or Stm1/Oc3
(MsMxp)
gbEx4Stm16Oc48x2 - 4 ports carry GbE, 2 ports
carry Stm16/Oc48 (MsMxp10GTCEr,
MsMxp10G)
stm16Oc48x4 - 4 ports carry Stm16/Oc48
(MsMxp10GTCEr, MsMxp10G)
gbEx4x2 - 2 x (4 ports carry GbE)
(MsMxpDQgbe)
gbEx2Fcx2x2 - 2 x (2 ports carry GbE, 2
ports carry 1G Fc or 1 port
carries 2G Fc) (MsMxpDQgbe)
gbEStm16Oc48Stm4Oc12Stm1Oc3 - 2 transponders carry GbE or
Stm16/Oc48, 2 transponders carry
Stm4/Oc12 or Stm1/Oc3 (MsMxpQMS2G5)
gbEStm16Oc48 - 4 transponders carry GbE or
Stm16/Oc48 (MsMxpQMS2G5)
syncEx14GLinex2 - 2 ports carry 4G MSMXP Lines
w. Protection, 1 port carry
Synchron GbE (MsMxp10G)
syncEx10 - 10 ports carry synchron GbE
(MsMxp10G)
gbEx3Stm4Oc12x1Stm1Oc3x3Basic - Like gbEx3Stm4Oc12x1Stm1Oc3x3,
with an alternative processing
of the STM client signal (MsMxp)
gbESyncEx3Stm4Oc12Stm1Oc3x1Basic - Like
gbESyncEx3Stm4Oc12Stm1Oc3x1,
with an alternative processing
of STM client signal (MsMxp)
cpri3x3syncEx2 - 3 ports carry cpri3 (2457.6 Mbps),
2 ports carry synchron GbE (fhmxp10g)
syncEx1Cpri4x3 - 3 ports carry cpri4 (3072.0 Mbps),
1 port carries synchron GbE (fhmxp10g)rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.77 |
wdmIfSelectTrafficCombinationSelect the traffic combination of the board.ro CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.78 |
wdmIfObjectPropertyProperty mask.ro ObjectProperty .1.3.6.1.4.1.8708.2.4.2.2.1.1.79 |
wdmIfTxPowerLevelThe transmitted power level in units of 0.1 dBm.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.80 |
wdmIfLaserTempActualThe actual laser temperature in units of
0.1 degrees centigrade.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.81 |
wdmIfTrxFailedA transceiver hardware failure is detected.
A: The transceiver fails.
D: The transceiver is replaced.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.82 |
wdmIfDisabledThe interface is disabled.
A: Interface disabled.
D: Interface enabled.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.83 |
wdmIfLoopbackThe interface is set in loopback mode.
A: Loopback enabled.
D: Loopback disabled.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.84 |
wdmIfContinousOptimizationContinuously run the optimization of the
decision threshold.
enabled - continous optimization enabled.
disabled - continous optimization disabled.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.85 |
wdmIfThresholdOptimizationResultCauseThis text descibes the cause why the latest
optimize command failed. The information
is only valid if the thresholdOptimizationState
is finishedFailed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.2.1.1.86 |
wdmIfDistributionRoleNote: This attribute is deprecated!
The distribution role of the line function
- terminal: normal point-to-point operation
- broadcastHub: broadcast on both lines.
- broadcastSatellite: drop-and-continuerw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.87 |
wdmIfConfigurationCommandNote: This attribute is deprecated!
Select the operation mode of the line.
- terminal: normal point-to-point operation
- broadcastHub: broadcast on both lines.
- broadcastSatellite: drop-and-continuero CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.88 |
wdmIfNoFrequencySetThe tunable laser frequency has not been set.
A: Tunable laser frequency is not set.
D: Tunable laser frequency is set.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.89 |
wdmIfFormatThe signal format
FecLan10GbE1A: iWDM 10G framing format type 1A (TPD10GBE-BU, GBE9/MXP10GFEC)
FecLan10GbE1B: iWDM 10G framing format type 1B (TPQ10GFEC, MS-MXP/10G,TPQ10GFECI)
Iwdm40Gb: iWDM 40G framing format (MS-TP/40G, MS-MXP/40G)rw SignalFormat .1.3.6.1.4.1.8708.2.4.2.2.1.1.90 |
wdmIfConfigurationFormatCommandCommand to change the signal format.
OTU-2 can be selected.ro CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.91 |
wdmIfOHTransparencyNote: This attribute is deprecated!
The 'OH Transparency' setting shall be set to 'off'
for standard SDH/SONET mode. Does not work when
client wrapper is enabled.
When set to 'on', the following tributary OH-bytes
are transparently transported: E1, E2, F1, D1-D3,
D4-D12, K1, K2, J0
The following are always terminated:
B1, B2, M1 and S1.rwdeprecated Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.92 |
wdmIfLinkDownNote: This attribute is deprecated!
A: Failure to negotiate a connection with the
other party.
D: A connection is negotiated.rodeprecated FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.93 |
wdmIfAutoNegotiationModeNote: This attribute is deprecated!
The wanted auto negotiation mode.
off - auto negotiation process is disabled
on - auto negotiation process is enabledrwdeprecated Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.94 |
wdmIfAutoNegotiationStatusNote: This attribute is deprecated!
The result of the auto negotiation procedure
incomplete - the result is still pending
half - half duplex
full - full duplexrodeprecated Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.95 |
wdmIfFlowControlModeNote: This attribute is deprecated!
The mode for handling of pause messages between
the peers.
noPause - PAUSE frame reception and
transmission is disabled
rxPause - PAUSE frame reception is enabled
(asymmetric)
txPause - PAUSE frame transmission is enabled
(asymetric)
bothPause - send and accept pause messages
(symmetric).rwdeprecated Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.96 |
wdmIfGroupLineModeIndicates whether the interface is grouped
into a ROADM-Line-group.
disabled - The interface is not grouped into
a ROADM-Line-group.
enabled - The interface is grouped into a
ROADM-Line-group.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.97 |
wdmIfFecTypeSet type of FEC.
enhancedFec - 2nd generation Enhanced FEC
(rate compatible with G.709
but > 2 dB additional coding
gain)
g709 - 1st generation FEC according to
ITU-T G.709 (near 6 dB coding gain).rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.98 |
wdmIfFarEndLoopbackLoop the wdm RX signal back to the wdm TX.
This is also called Facility loopback.
disabled - the signal is not looped
enabled - the signal is looped.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.99 |
wdmIfFarEndLoopbackTimeoutTimeout for far end loopback (a.k.a. facility
loopback) to make sure connection to node is
not lost if ppp link is broken.
The unit is hour. 0.1 means 6 minutes.rw Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.100 |
wdmIfFarEndLoopbackEnabledFar end loopback (a.k.a. facility loopback)
is enabled.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.101 |
wdmIfChangeLoopbackCommandCommand to change Loopback and loopbacktimeoutro CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.102 |
wdmIfFecFailureToo many errors to get valid FEC statistics. It is not
possible to run control loops based on FEC statistics.
A: Too many errors to get valid FEC statistics.
D: The FEC statistics is valid.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.103 |
wdmIfTxSignalStatusThe operational state for outgoing (TX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The signal quality is impaired.
up - The signal is OK.
notApplicable (2147483647) - Attribute is not used on board.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.104 |
wdmIfRxSignalStatusThe operational state for incoming (RX) signal
of the interface.
down - A major fault has occurred
degraded - The signal quality is impaired.
up - The signal is OK.
notApplicable (2147483647) - Attribute is not used on boardro Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.105 |
wdmIfNearEndLoopbackLoop the wdm TX signal back to the wdm RX.
This is also called Terminal loopback.
disabled - the signal is not looped
enabled - the signal is looped.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.106 |
wdmIfNearEndLoopbackTimeoutTimeout for near end loopback (a.k.a. terminal
loopback) to make sure connection to node is
not lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes.rw Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.107 |
wdmIfNearEndLoopbackEnabledNear end loopback (a.k.a. terminal loopback)
is enabled.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.108 |
wdmIfChangeNearEndLoopbackCommandCommand to change near end loopback (a.k.a.
terminal loopback) and loopbacktimeoutro CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.109 |
wdmIfSignalDegradedToo many error corrected.
If more errors are corrected
it might effect the client signal
in a negative way.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.110 |
wdmIfHubProtectionModeChoose if the line should be used in
hub protection. (needs to be setup in mba)
disabled - Port is not in hub protection (default)
enabled - Hub protection is enabledrw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.111 |
wdmIfActualFormatThe actual signal format.ro SignalFormat .1.3.6.1.4.1.8708.2.4.2.2.1.1.112 |
wdmIfTdcDispersionShows current dispersion value in the unit.rw Integer32 (-800..800) .1.3.6.1.4.1.8708.2.4.2.2.1.1.113 |
wdmIfTdcDispersionCommandSets state and dispersion in the unit.ro CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.114 |
wdmIfTdcDispersionModeStates the current mode of the TDC dispersion.
Mode:
auto - The TDC is in auto optimising state.
startValue - Starts with the desired value,
then it goes to auto afterward.
manula - The TDC is in manual/forced mode.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.115 |
wdmIfLineControlLoopCurrentStateThe current state of the unit. The unit
is ready if state=Automatic fine-tuning.
The states could be one of the followings:
Init DPSK.
DPSK Tx Locked.
Init EDFA.
Coarse-tune DPSK.
Coarse-tune TDC, first step.
Coarse-tune TDC, second step.
Fine-tune TDC.
Fine-tune DPSK.
TDC in manual/forced mode.
Automatic fine-tuning.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.2.1.1.116 |
wdmIfSignalDegradeThresholdThreshold for signal degraded alarm,
based on BER value.
The threshold is settable on the first
line port, affecting all line ports.
Predefined BER levels
rxBerLevel1 = 1E-12
rxBerLevel2 = 1E-13
rxBerLevel3 = 1E-15rw BerLevel .1.3.6.1.4.1.8708.2.4.2.2.1.1.117 |
wdmIfTrxThresholdOptimizationStateThreshold Optimization State.
Idle - No regulation done
Searching - Rough threshold regulation
is being performed
Optimizing - Fine threshold regulation
is being performed
Steady State - Regulation at steady state
Failed(trafficLoss) - Failure due to traffic loss
(FEC failure, Loss of sync,
LOF, Bitrate Mismatch)
Failed(LOS) - Failure due to loss of singalro Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.118 |
wdmIfTrxDecisionThresholdThe threshold is automatically optimized if the
'Continous optimization' functionality is enabled.
Press the 'Optimize' button to manually trigger
the optimization routine once.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.2.1.1.119 |
wdmIfSwControlledLaserShutdownenabled - the laser is turned off for a specified time, until the timer expires
disabled - normal statero Enumeration .1.3.6.1.4.1.8708.2.4.2.2.1.1.120 |
wdmIfChangeSwControlledLaserShutdownCommandCommand to shut the laser down for a user-defined period of time.
This setting will over-ride other laser control functions like ALS and protection.
The timer can be selected in minutes: [1..30] minutes.
When the timer expires, the normal laser control functions will take over
the control of the laser.
When in the shut-down state, the same command can be issued to cancel the
operation prematurely.ro CommandString .1.3.6.1.4.1.8708.2.4.2.2.1.1.121 |
wdmIfControlledLaserShutdownEnabledSoftware controlled laser shutdown is enabled.
Activation - When the command is successfully applied.
De-activation - When the timer expires, or the operation is manually cancelled.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.2.1.1.122 |
wdmIfAidThe access identifier (AID) of the interface.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.2.1.1.123 |
wdmIfPhysicalLocationThe physical location of the if.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.2.1.1.124 |
wdmIfTrxTunableThe transceiver is of tunable type.ro TruthValueWithNA .1.3.6.1.4.1.8708.2.4.2.2.1.1.125 |
wdmProtList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.3 |
wdmProtTableThe protection group table. SEQUENCE OF WdmProtEntry .1.3.6.1.4.1.8708.2.4.2.3.1 |
wdmProtEntryAn entry in the protection group table. WdmProtEntry .1.3.6.1.4.1.8708.2.4.2.3.1.1 |
wdmProtIndexAn arbitrary index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.3.1.1.1 |
wdmProtNameThe name of the object, for example
'pg:1:2:1-2:1:3:1-2', where the numbers indicate the
subrack, slot and TX-RX port number for the left and
right interface of the group.
The interface is either a client interface
or a line interface. This depends on the
protection type, which in turn depends on
the type of board that is involved.ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.3.1.1.2 |
wdmProtDescrUser configurable label.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.3.1.1.3 |
wdmProtRightSubrackThe subrack number for this protected
interface.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.4 |
wdmProtRightSlotThe slot number for this protected
interface.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.5 |
wdmProtRightPortThe port number for the TX side of this
protected interface. Not necessary for boards
with only one interface.rw PortNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.6 |
wdmProtLeftSubrackThe subrack number for the other protected
interface.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.7 |
wdmProtLeftSlotThe slot number for the other protected
interface.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.8 |
wdmProtLeftPortThe port number for the TX side of the other
protected interface. Not necessary for boards
with only one interface.rw PortNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.9 |
wdmProtLastChangeTimeThe time the operational state of the protection
group was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.3.1.1.10 |
wdmProtAdminStatusThe administrative state for the protection
group.
down - The protection group is inactive.
leftForced - The left side is forced active.
rightForced - The right side is forced active.
auto - The application choses which side should
be active. This should be the normal mode of
operation.
toggle - Switch the active side of the protection
group. Only applicable in 'auto' state.
After setting adminStatus to 'toggle' it again
receives the 'auto' value.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.11 |
wdmProtOperStatusNote: This object is deprecated.
The operational state for the protection group.
bothDown - both sides down
leftDownRightUp - left side down, right side up
leftDownRightStandby - left side down (forced),
right side standby
leftStandbyRightDown - left side standby, right
side down (forced)
leftStandbyRightUp - left side standby, right
side up
leftUpRightDown - left side up, right side down
leftUpRightStandby - left side up, right side
standbyrodeprecated Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.12 |
wdmProtRowStatusManages creation and deletion of conceptual rows.
See also SNMPv2-TC.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.3.1.1.13 |
wdmProtServiceDegradedProtection service degraded.
A: One of the sides of the protection group has
signal failure or one side is forced active.
D: Both sides of the protection group are
available (The signal is recovered or the
forced active side is released).ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.3.1.1.14 |
wdmProtServiceFailureProtection service failure.
A: Both sides of the protection group has
signal failure or the side that is forced
active has signal failure.
D: One of the sides of the protection group
is available (The signal is recovered or the
forced active side is released).ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.3.1.1.15 |
wdmProtActiveSideThe operational state for the protection group.
none - no side is active.
left - the left side is active.
right - the right side is active.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.16 |
wdmProtLeftStatusThe operational state for the left side of the
protection group.
down - this side is out of service.
up - this side is active.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.17 |
wdmProtRightStatusThe operational state for the right side of
the protection group.
down - this side is out of service.
up - this side is active.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.18 |
wdmProtProtectionTypeDifferent types of protection realisation
and modelling. The information is intended
for the TNM.
eqAndFiberProtection - multiple boards,
e.g. two tpMr2500 or tpMr25v2
fiberProtectionI - single board,
e.g. FPU
fiberProtectionII - single board,
e.g. QMR
fiberProtectionIII - single board,
e.g. tpDDGbE
fiberProtectionIIII - single board,
e.g. tpD10GbE
singleEndedBiDirLineProtection - single ended bidirection line protection,
e.g. fhau1ro Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.19 |
wdmProtObjectPropertyProperty mask.ro ObjectProperty .1.3.6.1.4.1.8708.2.4.2.3.1.1.20 |
wdmProtWrapperModeDefines how the wrapper will operate
in correlation with the traffic switch.
followTraffic - use the same interface
as the traffic is selected from.
fixedToDefaultInterface - wrapper is fixed
to the predefined interface. This is the
interface over which the PPP-link is defined.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.21 |
wdmProtWrapperStateShows which interface that currently
is used for wrapper communication.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.22 |
wdmProtLeftCommSubrackThe subrack number of the left communication link
for this protection group.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.23 |
wdmProtLeftCommSlotThe slot number of the left communication link for
this protection group.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.24 |
wdmProtLeftCommPortThe port number of the left communication link for
this protection grouprw PortNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.25 |
wdmProtRightCommSubrackThe subrack number of the right communication link
for this protection group.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.26 |
wdmProtRightCommSlotThe slot number of the right communication link for
this protection group.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.27 |
wdmProtRightCommPortThe port number of the right communication link for
this protection grouprw PortNumber .1.3.6.1.4.1.8708.2.4.2.3.1.1.28 |
wdmProtLeftCommInterfaceThe interface used for the left communication link
for this protection group.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.3.1.1.29 |
wdmProtRightCommInterfaceThe interface used for the right communication link
for this protection group.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.3.1.1.30 |
wdmProtCommunicationFailureProtection group communication failure
A: There are several underlying criterias for this:
- Loss of signal on the communication link
- Errors on the communication link
- Supervision failures
- Missing status messages for the protection group
D: Status messages are coming in as they should and
the link supervision works.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.3.1.1.31 |
wdmProtHubTrafficConfigMismatchTraffic configuration received over the two lines differ.
A: The traffic configuration received
over the two lines do not match.
D: Both lines have the same traffic configurationro FaultStatus .1.3.6.1.4.1.8708.2.4.2.3.1.1.32 |
wdmProtSignalDegradeProtectionInclude signal degraded alarm as a protection
switch criteria.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.33 |
wdmProtRevertiveSwitchWtrTimerWhen revertive mode is enabled and traffic is running on
secondary path, this timer decides when to switch back to
primary path (when the primary path is up and working again).
Please note! To make sure that the desired timer value is used,
always change this separatly from other settings.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.3.1.1.34 |
wdmProtRevertiveSwitchIf revertive protection switch is enabled, the primary
path will automaticly be chosen as working path
if it is operational. A switch back to the primary
path will however be delayed with the period of time
given by the user.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.35 |
wdmProtRevertiveSwitchPrimaryPathThe interface in the protection group that should be used
as prefered working path.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.36 |
wdmProtRevertiveSwitchSecondaryPathThe interface in the protection group that is used as
prefered protection path. This is set automatically when
choosing the primary working path.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.3.1.1.37 |
wdmProtSecondaryPathUsedAlarm indicating that the alternative secondary path is currently used,
when revertive switching is enabled.
A: Secondary path is used as working path.
D: Primary path is used as working path.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.3.1.1.38 |
lumentisWdmNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.4 |
wdmNotifyPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.4.0 |
wdmProtOperStatusBothDownSent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.1 |
wdmProtOperStatusLeftDownRightUpSent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.2 |
wdmProtOperStatusLeftDownRightStandbySent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.3 |
wdmProtOperStatusLeftStandbyRightDownSent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.4 |
wdmProtOperStatusLeftStandbyRightUpSent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.5 |
wdmProtOperStatusLeftUpRightDownSent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.6 |
wdmProtOperStatusLeftUpRightStandbySent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.7 |
wdmIfLaserStatusOnSent when the laser of the interface is turned
on. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.8 |
wdmIfLaserStatusOffSent when the laser of the interface is turned
off. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.9 |
wdmProtStatusChangedSent when the protection group changes
operational status. NOTIFICATION-TYPE .1.3.6.1.4.1.8708.2.4.2.4.0.10 |
wdmPassiveIfList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.5 |
wdmPassiveIfTableThe interface list. SEQUENCE OF WdmPassiveIfEntry .1.3.6.1.4.1.8708.2.4.2.5.1 |
wdmPassiveIfEntryAn entry in the interface list.
Each interface consists of a uni- or
bi-directional port. WdmPassiveIfEntry .1.3.6.1.4.1.8708.2.4.2.5.1.1 |
wdmPassiveIfIndexAn arbitrary index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.5.1.1.1 |
wdmPassiveIfNameThe management name of the interface, for
example 'wdmi:1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number.ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.5.1.1.2 |
wdmPassiveIfDescrUser configurable label.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.5.1.1.3 |
wdmPassiveIfSubrackThe number of the subrack where the interface
is located.ro SubrackNumber .1.3.6.1.4.1.8708.2.4.2.5.1.1.5 |
wdmPassiveIfSlotThe number of the slot where the interface is
located.ro SlotNumber .1.3.6.1.4.1.8708.2.4.2.5.1.1.6 |
wdmPassiveIfPortThe number of the port where the interface
is located.ro PortNumber .1.3.6.1.4.1.8708.2.4.2.5.1.1.7 |
wdmPassiveIfInvPhysIndexOrZeroThe row in the invPhysTable for this interface.
Set to 0 if not known.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.5.1.1.8 |
wdmPassiveIfDirectionThe type of signal the interface expects.
rx - Only ingoing signal.
LambdaType, LambdaMin and LambdaMax indicates the
frequency properties for the ingoing signal.
tx - Only outgoing signal.
LambdaType, LambdaMin and LambdaMax indicates the
frequency properties for the outgoing signal.
biDi - Ingoing and outgoing signal on the same
port. LambdaType, LambdaMin and LambdaMax
indicates the frequency properties for the
bi-directional signal.ro PortType .1.3.6.1.4.1.8708.2.4.2.5.1.1.9 |
wdmPassiveIfLambdaTypeThe type of wavelengths the port of the
interface can accomodate.
fixed - The port received or transmits a fixed
frequency.
range - The port can handle a range of
frequencies. Not used.
transparent - There are no frequency properties
associated with the port.ro LambdaType .1.3.6.1.4.1.8708.2.4.2.5.1.1.10 |
wdmPassiveIfLambdaThe frequency given in hundreds of GHz
(0.01 GHz). Set to 0 for transparent ports.ro LambdaFrequency .1.3.6.1.4.1.8708.2.4.2.5.1.1.11 |
wdmPassiveIfLambdaMaxThe maximum frequency (for the 'wavelength')
in GHz.ro LambdaFrequency .1.3.6.1.4.1.8708.2.4.2.5.1.1.12 |
wdmPassiveIfLastChangeTimeThe time when the state of the interface entry
was last changed.rodeprecated DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.5.1.1.13 |
wdmPassiveIfExpectedLambdaThe frequency of the 'wavelength' given in
hundreds of GHz (0.01 GHz).
This attribute can be written via SNMP.rw LambdaFrequency .1.3.6.1.4.1.8708.2.4.2.5.1.1.14 |
wdmPassiveIfUnexpectedLambdaThe actual frequency does not match the
hundreds of GHz (0.01 GHz).
The actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured frequency does not match the
actual frequency.
D: The configured frequency matches the actual
frequency.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.5.1.1.15 |
wdmPassiveIfAdminStatusThe administrative state for the
port.
down - The alarm are inhibited
up - Alarms are reportedrw Enumeration .1.3.6.1.4.1.8708.2.4.2.5.1.1.16 |
wdmPassiveIfOperStatusThe operational state for the
port.
notPresent - The board is missing
down - Admin down
up - The board is present and admin upro BoardOrInterfaceOperStatus .1.3.6.1.4.1.8708.2.4.2.5.1.1.17 |
wdmPassiveIfObjectPropertyProperty mask.ro ObjectProperty .1.3.6.1.4.1.8708.2.4.2.5.1.1.18 |
wdmPassiveIfExpectedLambdaMaxThe Max frequency of the 'wavelength' range
given in hundreds of GHz (0.01 GHz).
This attribute can be written via SNMP.rw LambdaFrequency .1.3.6.1.4.1.8708.2.4.2.5.1.1.19 |
wdmPassiveIfAidThe access identifier (AID) of the interface.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.5.1.1.20 |
wdmPassiveIfPhysicalLocationThe physical location of the if.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.5.1.1.21 |
wdmPassiveIfIfNoThe number of the port where the interface
is located.ro PortNumber .1.3.6.1.4.1.8708.2.4.2.5.1.1.22 |
wdmVc4List OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.6 |
wdmVc4TableThe interface list. SEQUENCE OF WdmVc4Entry .1.3.6.1.4.1.8708.2.4.2.6.1 |
wdmVc4EntryAn entry in the interface list. WdmVc4Entry .1.3.6.1.4.1.8708.2.4.2.6.1.1 |
wdmVc4IndexAn arbitrary index assigned to each if entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.6.1.1.1 |
wdmVc4NameThe management name of the vc4/vc3/STS-1,
e.g. vc4:1:2:1-2:8 where the first number
indicates sub-rack, the second slot number and
the third/forth are the port numbers. The last
number is the vc4/vc3/STS-1 id within the STM16/STS-48 frame.ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.6.1.1.2 |
wdmVc4DescrUser configurable label.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.6.1.1.3 |
wdmVc4SubrackThe number of the subrack where the vc4/vc3/STS-1 is
located.ro SubrackNumber .1.3.6.1.4.1.8708.2.4.2.6.1.1.4 |
wdmVc4SlotThe number of the slot where the vc4/vc3/STS-1 is
located.ro SlotNumber .1.3.6.1.4.1.8708.2.4.2.6.1.1.5 |
wdmVc4TxPortThe number of the port where the TX-side of the
vc4/vc3/STS-1 is located.ro PortNumber .1.3.6.1.4.1.8708.2.4.2.6.1.1.6 |
wdmVc4RxPortThe number of the port where the RX-side of the
vc4/vc3/STS-1 is located.ro PortNumber .1.3.6.1.4.1.8708.2.4.2.6.1.1.7 |
wdmVc4Vc4The id of the vc4 within the STM64/STM16 frame. When
Sonet, the id of the STS3 within the OC192/OC48 frame.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.6.1.1.8 |
wdmVc4ObjectPropertyProperty mask.ro ObjectProperty .1.3.6.1.4.1.8708.2.4.2.6.1.1.9 |
wdmVc4AuAlarmIndicationSignalAlarm indication signal (AIS).
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH/Sonet signal is detected.
D: SDH/Sonet signal recovered.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.6.1.1.10 |
wdmVc4AuLossOfPointerLoss of pointer detected.
Applicable for SDH/Sonet signal formats.
A: A loss of pointer is detected.
D: SDH/Sonet signal recovered.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.6.1.1.11 |
wdmVc4RxSignalStatusThe operational state for incoming (RX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The signal quality is impaired.
up - The signal is OK.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.6.1.1.12 |
wdmVc4ConcatenationStatusDescribes if and how the VC4s are concatenated.
In case of sonet how the STS3s are concatenated.
on - Concatenation is used.
off - No concatenation is used.
can be vc3 (STS-1),
vc4 (STS-3, STM1/OC3),
vc4x4c (STM4/OC12),
vc4x16c (STS-48, STM16/OC48),
vc4x64c (STS-128, STM64/OC192),
sts1 (STS-1),
sts3c (STS-3 concatenated),
sts12c (STS-12 concatenated).ro Enumeration .1.3.6.1.4.1.8708.2.4.2.6.1.1.13 |
wdmVc4PayloadStatusDescribes if the VC4/STS3 contains payload.
equipped - VC4/STS3 contains payload.
unequipped - No payload in VC4/STS3.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.6.1.1.14 |
wdmVc4ConnectionStatusShows the name of the client port and
possible subchannel/vc4 that it is connected to
or Unconnected if not connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.6.1.1.15 |
wdmVc4ConnectedForeignIndexShows the index of the connected interface.
Or 0 if unconnected.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.6.1.1.16 |
wdmVc4AdminStatusThe administrative state for the vc4/vc3/STS-1.
down - The vc3/vc4/STS-1 should not be used. This
vc4/vc3 will not affect rxSignalStatus.
up - The vc4/vc3/STS-1 should be used. This
vc4/vc3/STS-1 will affect rxSignalStatus.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.6.1.1.17 |
wdmRemoteProtList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.7 |
wdmRemoteProtTableThe protection group table. SEQUENCE OF WdmRemoteProtEntry .1.3.6.1.4.1.8708.2.4.2.7.1 |
wdmRemoteProtEntryAn entry in the protection group table. WdmRemoteProtEntry .1.3.6.1.4.1.8708.2.4.2.7.1.1 |
wdmRemoteProtIndexAn arbitrary index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.7.1.1.1 |
wdmRemoteProtNameThe name of the object, for example
'rpg:1:2:1', where the numbers indicate the
subrack, slot and TX port number for the local
interface of the group.
The interface is either a client interface
or a line interface. This depends on the
protection type, which in turn depends on
the type of board that is involved.ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.7.1.1.2 |
wdmRemoteProtDescrUser configurable label.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.7.1.1.3 |
wdmRemoteProtLocalSubrackThe subrack number for this protected
interface.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.7.1.1.4 |
wdmRemoteProtLocalSlotThe slot number for this protected
interface.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.7.1.1.5 |
wdmRemoteProtLocalPortThe port number for the TX side of this
protected interface.rw PortNumber .1.3.6.1.4.1.8708.2.4.2.7.1.1.6 |
wdmRemoteProtCommSubrackThe subrack number of the communication link for
this protection group.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.7.1.1.7 |
wdmRemoteProtCommSlotThe slot number of the communication link for
this protection group.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.7.1.1.8 |
wdmRemoteProtCommPortThe port number of the communication link for
this protection grouprw PortNumber .1.3.6.1.4.1.8708.2.4.2.7.1.1.9 |
wdmRemoteProtCommInterfaceThe port number of the communication link for
this protection groupro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.7.1.1.10 |
wdmRemoteProtLastChangeTimeThe time the operational state of the protection
group was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.7.1.1.11 |
wdmRemoteProtIpAddressThe IP-address of the remote node.rw IpAddress .1.3.6.1.4.1.8708.2.4.2.7.1.1.12 |
wdmRemoteProtIdentifierThe identifier (name) of the protection group
that is understod by both the local and the remote
node.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.7.1.1.13 |
wdmRemoteProtRoleThe role of the node in this protection group.
master - the manager should read info from this node.
slave - the manager should read from the other noderw Enumeration .1.3.6.1.4.1.8708.2.4.2.7.1.1.14 |
wdmRemoteProtAdminStatusThe administrative state for the protection
group.
down - The protection group is inactive.
localForced - The local side is forced active.
remoteForced - The remote side is forced active.
auto - The application choses which side should
be active. This should be the normal mode of
operation.
toggle - Switch the active side of the protection
group. Only applicable in 'auto' state.
After setting adminStatus to 'toggle' it again
receives the 'auto' value.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.7.1.1.15 |
wdmRemoteProtRowStatusManages creation and deletion of conceptual rows.
See also SNMPv2-TC.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.7.1.1.16 |
wdmRemoteProtActiveSideThe operational state for the protection group.
none - no side is active.
local - the local side is active.
remote - the remote side is active.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.7.1.1.17 |
wdmRemoteProtLocalStatusThe operational state for the local side of the
protection group.
down - this side is out of service.
up - this side is working.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.7.1.1.18 |
wdmRemoteProtRemoteStatusThe operational state for the remote side of
the protection group.
down - this side is out of service.
up - this side is working.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.7.1.1.19 |
wdmRemoteProtObjectPropertyProperty mask.ro ObjectProperty .1.3.6.1.4.1.8708.2.4.2.7.1.1.20 |
wdmRemoteProtServiceDegradedProtection service degraded.
A: One of the sides of the protection group has
signal failure or one side is forced active.
D: Both sides of the protection group are
available (The signal is recovered or the
forced active side is released).ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.7.1.1.21 |
wdmRemoteProtServiceFailureProtection service failure.
A: Both sides of the protection group has
signal failure or the side that is forced
active has signal failure.
D: One of the sides of the protection group
is available (The signal is recovered or the
forced active side is released).ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.7.1.1.22 |
wdmRemoteProtSetupProcedure to setup the protection group.
- Communication Interface
Select from a list of available interfaces
- Remote IP-address
Select from a list of discovered addresses or
enter a value
- Identifier
Select from a list of identifiers that have been
published by the node with the IP-address
selected above, or enter a unique value.
The identifier must be unique both in the local
node and in the remote node.
- Role
Select whether the local end of the protection
group shall be master or slave.ro CommandString .1.3.6.1.4.1.8708.2.4.2.7.1.1.23 |
wdmRemoteProtSetupFailureProtection group setup failure.
A: The defined remote IP-address and/or protection
group identifier can not be resolved with the
peer node.
D: The protection group can be resolvedro FaultStatus .1.3.6.1.4.1.8708.2.4.2.7.1.1.24 |
wdmRemoteProtRoleConflictProtection group master/slave conflict.
A: The protection group is resolved, but the two
peers have the same role defined - both master,
or both slave
D: Their respective roles differro FaultStatus .1.3.6.1.4.1.8708.2.4.2.7.1.1.25 |
wdmRemoteProtCommunicationFailureProtection group communication failure
A: There are several underlying criterias for this:
- Loss of signal on the communication link
- Errors on the communication link
- Supervision failures
- Missing status messages for the protection group
D: Status messages are coming in as they should and the
link supervision works.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.7.1.1.26 |
wdmCtrlChannelList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.8 |
wdmCtrlChannelTableThe interface list. SEQUENCE OF WdmCtrlChannelEntry .1.3.6.1.4.1.8708.2.4.2.8.1 |
wdmCtrlChannelEntryAn entry in the interface list. WdmCtrlChannelEntry .1.3.6.1.4.1.8708.2.4.2.8.1.1 |
wdmCtrlChannelIndexAn index assigned to each entry. The index contains information
about subrack, slot and port for controlled channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.1 |
wdmCtrlChannelNameThe management name of the channel, for example
'ch:1:2:1:959'
(ch:[subrack]:[slot]:[port]:[channel]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.8.1.1.2 |
wdmCtrlChannelSubrackThe subrack number of the unit where the controlled
channel is attenuated.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.8.1.1.3 |
wdmCtrlChannelSlotThe slot number of the unit where the controlled
channel is attenuated.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.8.1.1.4 |
wdmCtrlChannelTxPortThe port number of the controlled channel in the unit where
the channel is attenuated.ro PortNumber .1.3.6.1.4.1.8708.2.4.2.8.1.1.5 |
wdmCtrlChannelChannelThe frequency of the 'wavelength' given in
hundreds of GHz (0.01 GHz).rw LambdaFrequency .1.3.6.1.4.1.8708.2.4.2.8.1.1.6 |
wdmCtrlChannelGroupNumberThe number of the group to which the controlled
channel belongs.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.7 |
wdmCtrlChannelAdminStatusThe administrative state for the channel control.
down - The channel control is inactive. Channel
attenuation is set to its maximum value.
service - The channel control is activated but
alarms are suppressed. Intended for use during
service or re-configuration. When service is
concluded adminStatus should be set to 'up' again.
up - The channel control is active. Alarms are
not suppressed.rw BoardOrInterfaceAdminStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.8 |
wdmCtrlChannelWantedOutputPowerThe wanted output power.rw Integer32 (-260..120) .1.3.6.1.4.1.8708.2.4.2.8.1.1.9 |
wdmCtrlChannelCurrentOutputPowerThe actual output power.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.10 |
wdmCtrlChannelCurrentAttenuationThe current attenuation.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.11 |
wdmCtrlChannelForceRegulationCommandStarts a regulation manuallyro CommandString .1.3.6.1.4.1.8708.2.4.2.8.1.1.12 |
wdmCtrlChannelOuputPowerControlFailureAlarm raised when the wanted output power
can not be obtained. That is
a) The wanted power has not been obtained after the
maximum number of consequent control cycles.
b) Failure to read the current output power.
c) Failure to set attenuation when regulating
channel.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.13 |
wdmCtrlChannelCurrentPowerOutOfRangeAlarm raised when the current output power
is outside the 'regulation range' for the group.
At this point, no regulation will be performed on
the channel. The operator must change the
wantedOutputPower or the regulationRange.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.14 |
wdmCtrlChannelAttenuationOutOfRangeAlarm raised when the attenuation is at the maximum
or minimum values for the controlled device and the
wantedOutputPower cannot be obtained.
At this point, no regulation will be performed on
the channel.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.15 |
wdmCtrlChannelStatusThe regulation status of the channel.
initial - No regulation has been performed yet.
searching - The system is trying to detect the channel.
regulating - The system is regulating the output
power of the channel to the wanted
level.
ok - The output power of the channel is at the
wanted level.
notFound - Channel could not be detected in monitor.
error - Regulation of channel output power failed.
waiting - Channel is in queue for regulation startup
and will be started when ongoing
regulations and prior elements in the
startup queue have been processed.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.8.1.1.16 |
wdmCtrlChannelStartupChannelInitiates a safe startup procedure for the channel
when set to 'start'.
If the administrative status of the channel is
'down' or the channel is not detected by the monitor
unit, the system attempts to detect the channel as
follows:
1) The attenuation is set to its maximum value.
2) The attenuation is decreased until the channel is
detected by the monitor.
When the channel is detected, regulation of the
channel is started, ignoring the regulation range.
If the channel cannot be detected, channelStatus is
set to notFound. If regulation in fails,
channelStatus is set to error and an alarm is
raised.
When the startup sequence is finished, the
administrative status of the channel is set to 'up'.
If a regulation is ongoing when the startup
procedure is initiated, the channel is put on a
waiting queue until the ongoing regulation is
finished. The startup queue has a limited length. If
the queue is filled up with waiting channels,
further startup commands will be blocked until all
the queued channels have been started.
At times when it is not allowed to start the
channel, e.g. in commissioning mode or when the
queue is full, this attribute is set to 'blocked'
and cannot be set to start.
NOTE: The 'blocked' state is handled entirely by the
system and cannot be set or reset by the user.
The state of this attribute immediately returns to
'normal' when the startup procedure has been
initiated or the channel is put on the startup
queue.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.8.1.1.17 |
wdmCtrlChannelMonitorIndexShows the index of the connected monitor interface.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.18 |
wdmCtrlChannelStartupCommandInitiates a safe startup sequence for the
channel. If the administrative status of the channel
is 'down' or the channel is not detected by the
monitor unit, the system attempts to detect the
channel as follows:
1) The attenuation is set to its maximum value.
2) The attenuation is decreased until the channel is
detected by the monitor.
When the channel is detected, regulation of the
channel is started, ignoring the regulation range.
If the channel cannot be detected, channelStatus is
set to notFound. If regulation fails, channelStatus
is set to 'error' and an alarm is raised.
When the startup sequence is finished, the
administrative status of the channel is set to 'up'.
If a regulation is ongoing when the startup
procedure is initiated, the channel is put on a
waiting queue until the ongoing regulation is
finished. The startup queue has a limited length. If
the queue is filled up with waiting channels,
further startup commands will be blocked until all
the queued channels have been started.ro CommandString .1.3.6.1.4.1.8708.2.4.2.8.1.1.19 |
wdmCtrlChannelSfpMissingAn expected SFP is missing.
A(ctivation): An expected SFP is missing.
D(e-activation): The missing SFP is inserted.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.20 |
wdmCtrlChannelSfpMediaMismatchThe type of the SFP used for the channel port
is not the expected.
A(ctivation): Invalid or mismatching SFP media is
detected.
D(e-activation): The correct SFP is used.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.21 |
wdmCtrlChannelLossOfSignalLoss of signal at the channel port.
A(ctivation): Active loss of signal HW
indication.
D(e-activation): Inactive loss of signal HW
indication.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.22 |
wdmCtrlChannelDescrUser configurable label.
This attribute can be written via SNMP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.8.1.1.23 |
wdmCtrlChannelMaxAttenuationThe max attenuation limit on channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.24 |
wdmCtrlChannelMinAttenuationThe min attenuation limit on channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.25 |
wdmCtrlChannelAttenControlOffsetThe threshold offset to max/min attenuation on the channel.
If the threshold is reached, AttenControlDegraded alarm will be raised.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.8.1.1.26 |
wdmCtrlChannelAttenControlDegradedAlarm is raised when channel attenuation
is crossing threshold to max/min attenuation.
A(ctivation): Active the alarm indication.
D(e-activation): Inactive the alarm indication.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.27 |
wdmCtrlChannelNotFoundChannel not found.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.8.1.1.28 |
wdmCtrlGroupList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.9 |
wdmCtrlGroupTableThe interface list. SEQUENCE OF WdmCtrlGroupEntry .1.3.6.1.4.1.8708.2.4.2.9.1 |
wdmCtrlGroupEntryAn entry in the interface list. WdmCtrlGroupEntry .1.3.6.1.4.1.8708.2.4.2.9.1.1 |
wdmCtrlGroupIndexAn index assigned to each entry. Index contains
information about group number, subrack, slot and
port.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.9.1.1.1 |
wdmCtrlGroupNameThe management name of the group,
for example 'group:1' (group:[groupNumber]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.9.1.1.2 |
wdmCtrlGroupDescrUser configurable label.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.9.1.1.3 |
wdmCtrlGroupGroupNumberA unique number identifying the group.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.9.1.1.4 |
wdmCtrlGroupSubrackThe number of the subrack where the monitor unit is
located.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.9.1.1.5 |
wdmCtrlGroupSlotThe number of the slot where the monitor is located.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.9.1.1.6 |
wdmCtrlGroupPortThe monitor port where the group is connected.
Each character represents a port number, as shown:
a->1, b->2, c->3, d->4, e->5, f->6, g->7, h->8.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.9.1.1.7 |
wdmCtrlGroupMonitorNameThe management name of the monitor port,
for example 'ocm:1:2:1-A'
([monitortype]:[subrack]:[slot]:[port]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.9.1.1.8 |
wdmCtrlGroupAdminStatusThe administrative state for the group.
down - The group is de-activated. No regulations
will be performed.
service - The group is activated but alarms
are suppressed. Intended for use during service
or re-configuration. When service is concluded
adminStatus should be set to 'up' again.
up - The group is active. Regulations will be
performed regularly and on user orders.
Alarms are not suppressed.rw BoardOrInterfaceAdminStatus .1.3.6.1.4.1.8708.2.4.2.9.1.1.9 |
wdmCtrlGroupControlModeThe current control group mode.
normal - regulation is performed at the interval
defined in General -> Regulation interval
commissioning - the regulation is performed
continuously. After 15 minutes it will change back to
normal mode.
Note! When control group is in commissioning mode
the corresponding monitor port will still be in
'normal' mode.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.9.1.1.10 |
wdmCtrlGroupConfigurationCommandSelect which control mode to use:
normal - regulation is performed at the interval
defined in General -> Regulation interval
commissioning - the regulation is performed
continuously. After 15 minutes it will change back to
normal mode.ro CommandString .1.3.6.1.4.1.8708.2.4.2.9.1.1.11 |
wdmCtrlGroupForceRegulationCommandStarts a regulation manuallyro CommandString .1.3.6.1.4.1.8708.2.4.2.9.1.1.12 |
wdmCtrlGroupLockedRangeTo avoid frequent changes of attenuation, a range
can be defined around the wanted output power. A
control loop will not try to adjust power values
within the range.rw Integer32 .1.3.6.1.4.1.8708.2.4.2.9.1.1.13 |
wdmCtrlGroupRegulationRangeAn offset below the wanted output power
at which the 'Current Power Out Of Range'
alarm shall be raised.
When the current output power is so
far below the wanted output power,
the regulation stops and the alarm
is raised.
Applicable for normal mode.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.9.1.1.14 |
wdmCtrlGroupRegulationLastChangeTimeThe time when the group was last regulated.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.9.1.1.15 |
wdmCtrlGroupCommissioningModeAlarm raised when the group is put in commissioning
mode.
A: Commissioning mode is used
D: Normal modero FaultStatus .1.3.6.1.4.1.8708.2.4.2.9.1.1.16 |
wdmCtrlGroupAssociateChannelCreates one or several control channel objects and
associates them to the selected group.
User needs to specify:
- The board where the added channels are attenuated.
- The port(s) or channel(s) of that board to add.
- The wanted output power of the channel.ro CommandString .1.3.6.1.4.1.8708.2.4.2.9.1.1.17 |
wdmCtrlGroupNoOfChannelsThe current number of channels associated with this
group.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.9.1.1.18 |
wdmCtrlGroupStatusThe regulation status for the group
starting - the system is starting up
noRegulation - the group contains no channels to
regulate
reading - the control loop is reading the power from
the monitor
regulating - the control loop is calculating and
setting new attenuations
idle - the control loop is inactive until next
regulationro Enumeration .1.3.6.1.4.1.8708.2.4.2.9.1.1.19 |
wdmCtrlGroupTimeLeftThe remaining time (in seconds) to next regulation.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.9.1.1.20 |
wdmCtrlGroupOutputPowerMismatchThe total output power of the OCM differs by
more than 1.4dB from the monitor port
insertion loss value of the OA.
A: The total output power of the OCM differs from
the monitor port insertion loss by more than
1.4dB
D: Output power of OCM is within 1.4dB of the
monitor port insertion loss value againro FaultStatus .1.3.6.1.4.1.8708.2.4.2.9.1.1.21 |
wdmCtrlGroupTotalPowerTotal power of channels associated to
this group, based on OCM measurements.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.9.1.1.22 |
wdmCtrlGroupChannelStartupCommandInitiates a safe startup sequence for all the
channels of selected group. If the administrative
status of the channel is 'down' or the channel is
not detected by the monitor unit, the system attempts
to detect the channel as follows:
1) The attenuation is set to its maximum value.
2) The attenuation is decreased until the channel is
detected by the monitor.
When the channel is detected, regulation of the
channel is started, ignoring the regulation range.
If the channel cannot be detected, channelStatus is
set to notFound. If regulation fails, channelStatus
is set to 'error' and an alarm is raised.
When the startup sequence is finished, the
administrative status of the channel is set to 'up'.
If a regulation is ongoing when the startup
procedure is initiated, the channel is put on a
waiting queue until the ongoing regulation is
finished. The startup queue has a limited length. If
the queue is filled up with waiting channels,
further startup commands will be blocked until all
the queued channels have been started.ro CommandString .1.3.6.1.4.1.8708.2.4.2.9.1.1.23 |
wdmSubChannelList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.10 |
wdmSubChannelTableThe interface list. SEQUENCE OF WdmSubChannelEntry .1.3.6.1.4.1.8708.2.4.2.10.1 |
wdmSubChannelEntryAn entry in the interface list. WdmSubChannelEntry .1.3.6.1.4.1.8708.2.4.2.10.1.1 |
wdmSubChannelIndexAn index assigned to each entry. The index contains
information about subrack, slot and port for
controlled channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.10.1.1.1 |
wdmSubChannelNameThe management name of the interface, for example
'channel:1:2:1-2:19'
(channel:[subrack]:[slot]:[port]:[channel]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.10.1.1.2 |
wdmSubChannelIdThe channelId within the line signal.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.10.1.1.3 |
wdmSubChannelTypeShows what format(s) this channel is used for.
(e1t1, fe or gbeFe)ro Enumeration .1.3.6.1.4.1.8708.2.4.2.10.1.1.4 |
wdmSubChannelUnequippedShows whether the remote node has
inserted payload into this channel.
A: No payload is received on this channel
D: Payload is received againro FaultStatus .1.3.6.1.4.1.8708.2.4.2.10.1.1.5 |
wdmSubChannelConnectionStatusShows the name of the client port and
possible subchannel that it is connected to
or Unconnected if not connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.10.1.1.6 |
wdmSubChannelConnectedForeignIndexShows the index of the connected interface.
Or 0 if unconnected.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.10.1.1.7 |
wdmSubChannelCrossConnectConnect a subchannel to a specific client and
subchannelro CommandString .1.3.6.1.4.1.8708.2.4.2.10.1.1.8 |
wdmSubChannelDisconnectDisconnect existing crossConnectionsro CommandString .1.3.6.1.4.1.8708.2.4.2.10.1.1.9 |
wdmSubChannelRemoteAccessInterfaceShows the name of the client port in the remote
access node that terminated the sub channel.
For sub channels that are not terminated in the
remote node, 'Not Terminated' is shown.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.10.1.1.10 |
wdmSubChannelProtectedChannelIndexShows the index of the protected chanel.
Or 0 if not active protection.
updates when protection state is changed.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.10.1.1.11 |
wdmCtrlGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.11 |
wdmCtrlGlobalRegulationIntervalThe time interval between regulations in normal
mode.
interval5min - 5 minutes interval
interval30min - 30 minutes intervalrw Enumeration .1.3.6.1.4.1.8708.2.4.2.11.1 |
wdmCtrlGlobalRegulationStatusThe current status of the control loop.
initial - No regulation has been performed yet.
searching - Trying to detect channels.
reading - Reading power values from monitor unit.
regulating - Adjusting power levels.
idle - No regulation is ongoing.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.11.2 |
wdmCtrlGlobalLastRegulationThe date and time of the last regulation.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.11.3 |
wdmCtrlGlobalTimeLeftTime left to next scheduled regulation.
Unit: seconds.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.11.4 |
wdmDelayCompPGList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.12 |
wdmDelayCompPGTableDelay compensation for protection groups table. SEQUENCE OF WdmDelayCompPGEntry .1.3.6.1.4.1.8708.2.4.2.12.1 |
wdmDelayCompPGEntryAn entry in the table. WdmDelayCompPGEntry .1.3.6.1.4.1.8708.2.4.2.12.1.1 |
wdmDelayCompPGIndexAn index assigned to each entry. The index contains
information about subrack, slot and port for
controlled channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.12.1.1.1 |
wdmDelayCompPGNameThe management name of the entry, for example
'dcpg:1:3:17-18:1:3:19-20'
(dcpg:[subrack]:[slot]:[leftporttx]-[leftportrx]:[subrack]:[slot]:[rightporttx]-[rightportrx]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.12.1.1.2 |
wdmDelayCompPGUpIdThe UpId within the table.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.12.1.1.3 |
wdmDelayCompPGAdminStatusThe administrative state for the object.
service - The object is activated but alarms
are suppressed. Intended for use during service
or re-configuration. When service is concluded
adminStatus should be set to 'up' again.
up - The object is active. Regulations will be
performed regularly and on user orders.
Alarms are not suppressed.rw AdminStatusWithNA .1.3.6.1.4.1.8708.2.4.2.12.1.1.4 |
wdmDelayCompPGOperStatusThe operational state for the object.
notPresent - The object is not available.
down - The object is de-activated or there are
faults preventing its transition to the 'up' state.
up - The object is active.ro OperStatusWithNA .1.3.6.1.4.1.8708.2.4.2.12.1.1.5 |
wdmDelayCompPGAutoCompensationModeThe automatic delay compensation mode.rw EnabledDisabledWithNA .1.3.6.1.4.1.8708.2.4.2.12.1.1.6 |
wdmDelayCompPGAutoCompensationStateThe automatic delay compensation state.ro Enumeration .1.3.6.1.4.1.8708.2.4.2.12.1.1.7 |
wdmDelayCompPGDelayDifferenceThe current delay difference in nanoseconds, after compensation.
The difference is calculated as (right line current delay) - (left line current delay).ro Signed32WithNA .1.3.6.1.4.1.8708.2.4.2.12.1.1.8 |
wdmDelayCompPGDelayCompensationOORDelay compensation out-of-range.
alarm: The delay compensation is out-of-range.
ok: The delay compensation is in range.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.12.1.1.9 |
wdmDelayCompPGFiberLengthDifferenceOORFiber length difference out-of-range.
alarm: The fiber length difference is out-of-range.
ok: The fiber length difference is in range.ro FaultStatus .1.3.6.1.4.1.8708.2.4.2.12.1.1.10 |
wdmDelayCompPGDelayCompensationResetResets the automatic delay compensation.
After a successful reset the default value
(normal) is restored in this attribute.ro ResetWithNA .1.3.6.1.4.1.8708.2.4.2.12.1.1.11 |
wdmDelayCompLinkList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.13 |
wdmDelayCompLinkTableDelay compensation for protection group links table. SEQUENCE OF WdmDelayCompLinkEntry .1.3.6.1.4.1.8708.2.4.2.13.1 |
wdmDelayCompLinkEntryAn entry in the table. WdmDelayCompLinkEntry .1.3.6.1.4.1.8708.2.4.2.13.1.1 |
wdmDelayCompLinkIndexAn index assigned to each entry. The index contains
information about subrack, slot and port for
controlled channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.13.1.1.1 |
wdmDelayCompLinkNameThe management name of the entry, for example
'dclink:1:3:17-18'
(dclink:[subrack]:[slot]:[porttx]-[portrx]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.13.1.1.2 |
wdmDelayCompLinkUpIdThe UpId within the table.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.13.1.1.3 |
wdmDelayCompLinkCurrentDelayCompensationThe current delay compensation in nanoseconds.
Note, the granularity of this value is determined
by the hardware capabilities.ro Signed32WithNA .1.3.6.1.4.1.8708.2.4.2.13.1.1.4 |
wdmDelayCompLinkWantedDelayCompensationThe wanted delay compensation in nanoseconds.
Note, this value is only used by the system when
automatic delay compensation mode is disabled.rw Signed32WithNA .1.3.6.1.4.1.8708.2.4.2.13.1.1.5 |
wdmMeanChannelPowerControlGlobalList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.14 |
wdmMeanChannelPowerControlGlobalTableBogus table to hold one entry with a dialog attribute to create
entries in another table. SEQUENCE OF WdmMeanChannelPowerControlGlobalEntry .1.3.6.1.4.1.8708.2.4.2.14.1 |
wdmMeanChannelPowerControlGlobalEntryA list of links where the channel power will be adjusted WdmMeanChannelPowerControlGlobalEntry .1.3.6.1.4.1.8708.2.4.2.14.1.1 |
wdmMeanChannelPowerControlGlobalIndexAn index assigned to each entry. The index contains information
about subrack, slot and port for controlled channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.14.1.1.1 |
wdmMeanChannelPowerControlGlobalNameThe management name of this bogus entry, that only
exists to create other entries.
'bogus'ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.14.1.1.2 |
wdmMeanChannelPowerControlGlobalEntryCreateCreates a wdmMeanChannelPowerControl entry in another tablero CommandString .1.3.6.1.4.1.8708.2.4.2.14.1.1.3 |
wdmMeanChannelPowerControlList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.4.2.15 |
wdmMeanChannelPowerControlTableThe list of local links to balance channel power on SEQUENCE OF WdmMeanChannelPowerControlEntry .1.3.6.1.4.1.8708.2.4.2.15.1 |
wdmMeanChannelPowerControlEntryA list of links where the channel power will be adjusted WdmMeanChannelPowerControlEntry .1.3.6.1.4.1.8708.2.4.2.15.1.1 |
wdmMeanChannelPowerControlIndexAn index assigned to each entry. The index contains information
about subrack, slot and port for controlled channel.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.1 |
wdmMeanChannelPowerControlNameThe management name of the local link adjustment
entry 'meanChannelPowerControl:1:2:1'
(meanChannelPowerControl[oa subrack]:[oa slot]:[oa port]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.15.1.1.2 |
wdmMeanChannelPowerControlDescrUser configurable label.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.15.1.1.3 |
wdmMeanChannelPowerControlOcmSubrackThe subrack number of the ocm reading the oa
monitor port.rw SubrackNumber .1.3.6.1.4.1.8708.2.4.2.15.1.1.4 |
wdmMeanChannelPowerControlOcmSlotThe slot number of the ocm reading the oa
monitor port.
channel is attenuated.rw SlotNumber .1.3.6.1.4.1.8708.2.4.2.15.1.1.5 |
wdmMeanChannelPowerControlOcmPortThe monitor port of this local link
adjustment loop.rw Enumeration .1.3.6.1.4.1.8708.2.4.2.15.1.1.6 |
wdmMeanChannelPowerControlOaSubrackThe subrack number of the oa that is being
controlled by this local link adjustment
entryro SubrackNumber .1.3.6.1.4.1.8708.2.4.2.15.1.1.7 |
wdmMeanChannelPowerControlOaSlotThe slot number of the oa that is being
controlled by this local link adjustment
entryro SlotNumber .1.3.6.1.4.1.8708.2.4.2.15.1.1.8 |
wdmMeanChannelPowerControlOaPortThe port number of the oa that is being
controlled by this local link adjustment
entryro PortNumber .1.3.6.1.4.1.8708.2.4.2.15.1.1.9 |
wdmMeanChannelPowerControlMonitorNameThe management name of the monitor port,
for example 'ocm:1:2:1-A'
([monitortype]:[subrack]:[slot]:[port]).ro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.15.1.1.10 |
wdmMeanChannelPowerControlAdminStatusThe administrative state for the local link
adjustment entry.
down - The link adjustment is disabled
service - The link is adjusting the channel
power but alarms are suppressed.
Intended for use during service or
re-configuration. When service is concluded
adminStatus should be set to 'up' again.
up - The link adjustment is active.
Regulations will be performed regularly and
on user orders. Alarms are not suppressed.rw AdminStatusWithNA .1.3.6.1.4.1.8708.2.4.2.15.1.1.11 |
wdmMeanChannelPowerControlOperStatusThe operational state for the control group
down - The control group cannot operate due
to missing resources or other complications
up - The control group is activero BoardOrInterfaceOperStatus .1.3.6.1.4.1.8708.2.4.2.15.1.1.12 |
wdmMeanChannelPowerControlStartRegulationStarts a regulation manuallyro CommandString .1.3.6.1.4.1.8708.2.4.2.15.1.1.13 |
wdmMeanChannelPowerControlRegulationRangeAn offset below the wanted output power
at which the 'Current Power Out Of Range'
alarm shall be raised.
When the current output power is so
far below the wanted output power,
the regulation stops and the alarm
is raised.
Applicable for normal mode.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.14 |
wdmMeanChannelPowerControlLatestRegulationThe time when the link was last regulated.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.15.1.1.15 |
wdmMeanChannelPowerControlLatestChangeThe time when the link was latest adjustedro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.4.2.15.1.1.16 |
wdmMeanChannelPowerControlMonitorOffsetCalibrationFailedAlarm raised when calibration of the OCM port fails.
A: calibration of OCM port failed
D: Normal modero FaultStatus .1.3.6.1.4.1.8708.2.4.2.15.1.1.17 |
wdmMeanChannelPowerControlRegulationStateThe regulation status for the link
starting - the local link adjustment loop is
reading the power from the
monitor
regulating - the local link adjustment loop
is calculating and setting new
attenuation / wanted gain
idle - the local link adjustment loop is
inactive until next regulationro Enumeration .1.3.6.1.4.1.8708.2.4.2.15.1.1.18 |
wdmMeanChannelPowerControlTimeToNextRegulationThe remaining time (in minutes) to next regulation.ro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.19 |
wdmMeanChannelPowerControlWantedChannelPowerThe wanted output power.rw Integer32 (-150..100) .1.3.6.1.4.1.8708.2.4.2.15.1.1.20 |
wdmMeanChannelPowerControlCurrentChannelPowerThe actual output power.ro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.21 |
wdmMeanChannelPowerControlCurrentGainOA signal gain set by the local link
adjustment loopro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.22 |
wdmMeanChannelPowerControlTotalChannelOutputPowerTotal channel output powerro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.23 |
wdmMeanChannelPowerControlNumberOfChannelsNumber of channels read from OCMro Unsigned32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.24 |
wdmMeanChannelPowerControlAbsolutePowerOffsetAbsolute power offsetro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.25 |
wdmMeanChannelPowerControlRemainingPowerOffsetRemaining power offsetro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.26 |
wdmMeanChannelPowerControlMonitorOffsetTooLargeAlarm raised when the OCM monitor port offset is too large
A: OCM port offset too large
D: Normal modero FaultStatus .1.3.6.1.4.1.8708.2.4.2.15.1.1.27 |
wdmMeanChannelPowerControlChannelPowerOutOfRangeAlarm raised when the incomming channelpower is
too high or too low to regulate to the wanted
mean channel power
A: channel power out of range
D: Normal modero FaultStatus .1.3.6.1.4.1.8708.2.4.2.15.1.1.28 |
wdmMeanChannelPowerControlRegulationIntervalMinimum time between two regulations, a random
wait time of up to 15 seconds is added to this
value when calculating when the next regulation
should occurr.rw Unsigned32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.29 |
wdmMeanChannelPowerControlAmplifierOutputPortThe management name of the OA port controlled by
this control loopro MgmtNameString .1.3.6.1.4.1.8708.2.4.2.15.1.1.30 |
wdmMeanChannelPowerControlLatestAmplifierRxPowerThe latest amplifier input powerro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.31 |
wdmMeanChannelPowerControlLatestAmplifierTxPowerThe latest amplifier output powerro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.32 |
wdmMeanChannelPowerControlLocalIdStore the local ID since it will be needed when reading backupro Integer32 .1.3.6.1.4.1.8708.2.4.2.15.1.1.33 |