LUM-IFPHYSICAL-MIB
AI MIB Summary
The LUM-IFPHYSICAL-MIB module enables monitoring and configuration of optical transport physical layer interfaces compliant with ITU-T G.709, specifically tracking transceiver parameters, cage status, and interface timestamps. It provides granular visibility into hardware-level attributes for optical transceivers and their physical cages to facilitate fault isolation and performance verification in carrier-grade networks.
The MIB module for management of physical port objects.
This module describes the physical layer in ITU-T Recommendation G.709.
The tables contained in this MIB are:
(1) The General group contains some general attributes as time stamps and tables sizes.
(2) The Trx group contains information and configuration for all transceiver objects.
(3) The Cage group contains information and configuration for all cage objects.
Main OID:
lumIfPhysicalMIBModule.1.3.6.1.4.1.8708.1.1.47
59
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
59 total| Object Name |
|---|
lumIfPhysicalMIBModuleThe MIB module for management of physical port objects.
This module describes the physical layer in ITU-T Recommendation
G.709.
The tables contained in this MIB are:
(1) The General group contains some general attributes as time stamps
and tables sizes.
(2) The Trx group contains information and configuration for all
transceiver objects.
(3) The Cage group contains information and configuration for all
cage objects. MODULE-IDENTITY .1.3.6.1.4.1.8708.1.1.47 |
lumIfPhysicalConfs OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.47.1 |
lumIfPhysicalGroups OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.47.1.1 |
lumIfPhysicalCompl OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.47.1.2 |
lumIfPhysicalMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.47.2 |
ifPhysicalGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.47.2.1 |
ifPhysicalGeneralConfigLastChangeTimeThe time when the configuration of the MIB was
last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.1.1 |
ifPhysicalGeneralStateLastChangeTimeThe time when the state and/or configuration of
the MIB was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.1.2 |
ifPhysicalGeneralIfPhysicalTrxTableSizeSize of transceiver tablero Unsigned32 .1.3.6.1.4.1.8708.2.47.2.1.3 |
ifPhysicalGeneralIfPhysicalTrxConfigLastChangeTimeThe time when the configuration of the table was
last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.1.4 |
ifPhysicalGeneralIfPhysicalTrxStateLastChangeTimeThe time when the state and/or configuration of the
MIB was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.1.5 |
ifPhysicalGeneralIfPhysicalCageTableSizeSize of transceiver tablero Unsigned32 .1.3.6.1.4.1.8708.2.47.2.1.6 |
ifPhysicalGeneralIfPhysicalCageConfigLastChangeTimeThe time when the configuration of the table was
last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.1.7 |
ifPhysicalGeneralIfPhysicalCageStateLastChangeTimeThe time when the state and/or configuration of the
MIB was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.1.8 |
ifPhysicalTrxList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.47.2.2 |
ifPhysicalTrxTableThe if physical trx interface list. SEQUENCE OF IfPhysicalTrxEntry .1.3.6.1.4.1.8708.2.47.2.2.1 |
ifPhysicalTrxEntryAn entry in the ifPhysical trx list. IfPhysicalTrxEntry .1.3.6.1.4.1.8708.2.47.2.2.1.1 |
ifPhysicalTrxIndexAn index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.47.2.2.1.1.1 |
ifPhysicalTrxNameThe management name of the transceiver, for example
'trx:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.ro MgmtNameString .1.3.6.1.4.1.8708.2.47.2.2.1.1.2 |
ifPhysicalTrxConnIfBasicIfIndexAn index describing to which index in ifBasicIf table
this object is related to.ro Unsigned32WithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.3 |
ifPhysicalTrxLaserBiasMeasures laser bias current value in tenth of
mA (0.1 mA).ro Unsigned32WithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.4 |
ifPhysicalTrxLaserTempThe actual laser temperature in units of
0.1 degrees Centigrades.ro Integer32WithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.5 |
ifPhysicalTrxTrxClassString that describes the transceiver class.ro DisplayStringWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.6 |
ifPhysicalTrxTrxMediaDefines the transceiver media.
For example 'optical' or 'electrical'.rw TrxMediaWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.7 |
ifPhysicalTrxActualTrxMediaDefines the media and capability of the TRX.ro TrxMediaWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.8 |
ifPhysicalTrxTxSignalStatusThe state for outgoing (TX) signal
of the interface.
down - A major fault has occurred.
degraded - The signal quality is impaired.
up - The signal is OK.ro SignalStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.9 |
ifPhysicalTrxRxSignalStatusThe state for incoming (RX) signal
of the interface.
down - A major fault has occurred.
degraded - The signal quality is impaired.
up - The signal is OK.ro SignalStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.10 |
ifPhysicalTrxTransmitterFailedTransmitter failed.
The transceiver hardware has detected a failure
in the transmitter part.
Alarm - The transmitter has failed
Ok - The transmitter is OK againro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.11 |
ifPhysicalTrxNonQualifiedTrxNon-qualified transceiver.
The inserted transceiver does not have a legal
manufacturer code.
Alarm - A non-qualified transceiver is inserted.
Ok - The transceiver is qualified.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.12 |
ifPhysicalTrxTrxMissingTransceiver missing.
An expected transceiver is missing.
Alarm - An expected transceiver is missing.
Ok - The missing transceiver is inserted.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.13 |
ifPhysicalTrxTrxMediaMismatchTransceiver media mismatch.
The TRX media does not match the expected one.
Alarm - Invalid or mismatching trx media is
detected.
Ok - The (pluggable) transceiver or board is
replaced, or the configuration is changed.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.14 |
ifPhysicalTrxTrxRxStateThe current Rx state of the transciever, in case it is
a coherent CFP. The unit is ready if state=Ready.
The states could be one of the followings:
Rx State: Init started.
Rx State: Init ready.
Rx State: Frequency ready.
Rx State: Input signal received.
Rx State: A/D Converter ready.
Rx State: Dispersion compensated.
Rx State: Ready.ro DisplayStringWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.15 |
ifPhysicalTrxTrxTxStateThe current Tx state of the transciever, in case it is
a coherent CFP. The unit is ready if state=Ready.
The states could be one of the followings:
Tx State: Init started.
Tx State: Init ready.
Tx State: Data path locked.
Tx State: Laser ready off.
Tx State: Laser ready.
Tx State: Laser bias ready.
Tx State: Ready.ro DisplayStringWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.16 |
ifPhysicalTrxOpticalLayerMappingMismatchThe inserted transceiver does not support the
configuration of the optical layer mapping.
alarm: A transceiver with other supported optical layer
mapping than the requested mapping is inserted.
ok: The transceiver with the non-requested optical
layer mapping is removed, or the object is reconfigured.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.17 |
ifPhysicalTrxPowerCycleResetWhen the attribute is set to reset the trx power cycle
is re-initialised, meaning the trx is cold started. Then the attribute is set to normal again
automatically.
Note: This function is only to be used as a last resort to resolve a TRX deadlock. Please read I&C manual for further details before usage.
reset - Re-initialises the trx power cycle
normal - The trx power cycle is in normal statero ResetWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.18 |
ifPhysicalTrxUIdAn index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.47.2.2.1.1.19 |
ifPhysicalTrxAidThe access identifier (AID) of the trx.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.2.1.1.20 |
ifPhysicalTrxPhysicalLocationThe physical location of the trx.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.2.1.1.21 |
ifPhysicalTrxPowerOutOfRangeThe power classification of the transceiver exceeds the design limit of the board.
alarm: A transceiver with a power classification that exceeds
the design limit of the board is inserted.
ok: The transceiver with a power classification that exceeds
the design limit of the board is removed.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.22 |
ifPhysicalTrxLowTempThe temperature of the transceiver is below its designed limit.
alarm: The temperature of the transceiver is below its designed limit.
ok: The temperature of the transceiver is within designed limits.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.23 |
ifPhysicalTrxCommunicationFailureThe board is unable to communicate with the transceiver.
alarm: Protocol errors detected on the transceiver control link.
ok: No communication errors detected on the transceiver control link.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.24 |
ifPhysicalTrxSignalFormatNotSupportedThe signal format is not supported on this transceiver.
alarm: Signal format not supported.
ok: Signal format supported.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.25 |
ifPhysicalTrxTunableThe transceiver is of tunable type.ro TruthValueWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.26 |
ifPhysicalTrxEncrCommunicationFailureThe board is unable to communicate with the transceiver for
encryption related configuration.
alarm: Protocol errors detected on the transceiver encryption control link.
ok: No communication errors detected on the transceiver encryption control link.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.27 |
ifPhysicalTrxDoesNotSupportEncryptionNon-Encryption capable TRX installed.
alarm: Non-Encryption capable TRX installed.
ok: Encryption capable TRX installed.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.28 |
ifPhysicalTrxSelfTestDataCorruptionTRX self-test data corruption.
alarm: TRX self-test data is corrupted.
ok: TRX self-test data is okay.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.47.2.2.1.1.29 |
ifPhysicalTrxAutoLambdaCapabilityThe Auto Lambda capability of the TRX.
none - Inserted TRX does not support auto lambda
notApplicable - Interface does not support auto lambda or TRX is not inserted
dualEndedPeer - TRX for dual ended peer auto lambdaro AutoLambdaCapability .1.3.6.1.4.1.8708.2.47.2.2.1.1.30 |
ifPhysicalCageList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.47.2.3 |
ifPhysicalCageTableThe if physical cage list. SEQUENCE OF IfPhysicalCageEntry .1.3.6.1.4.1.8708.2.47.2.3.1 |
ifPhysicalCageEntryAn entry in the ifPhysical cage list. IfPhysicalCageEntry .1.3.6.1.4.1.8708.2.47.2.3.1.1 |
ifPhysicalCageIndexAn index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.47.2.3.1.1.1 |
ifPhysicalCageNameThe management name of the cage, for example
'cage:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.ro MgmtNameString .1.3.6.1.4.1.8708.2.47.2.3.1.1.2 |
ifPhysicalCageConnIfBasicIfIndexAn index describing to which index in ifBasicIf table
this object is related to.ro Unsigned32WithNA .1.3.6.1.4.1.8708.2.47.2.3.1.1.3 |
ifPhysicalCageSubrackThe number of the subrack in which the cage
module is present.ro SubrackNumber .1.3.6.1.4.1.8708.2.47.2.3.1.1.4 |
ifPhysicalCageSlotThe number of the slot in which the cage
module is present.ro Unsigned32 .1.3.6.1.4.1.8708.2.47.2.3.1.1.5 |
ifPhysicalCageAidThe access identifier (AID) of the cage.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.3.1.1.6 |
ifPhysicalCagePhysicalLocationThe physical location of the cage.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.47.2.3.1.1.7 |
ifPhysicalCageEquippedIs the entity equipped.ro TruthValueWithNA .1.3.6.1.4.1.8708.2.47.2.3.1.1.8 |
ifPhysicalCageUIdAn index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.47.2.3.1.1.9 |