LUM-IFBASIC-MIB
AI MIB Summary
The LUM-IFBASIC-MIB module manages basic interface attributes on LUM devices, exposing general system timestamps, GUI port naming conventions, and administrative or signal-level configuration parameters for all available network interfaces.
The MIB module for management of basic port objects.
The tables contained in this MIB are:
(1) The General group contains some general attributes as time stamps and tables sizes.
(2) The If group contains information about the name of the port that is used in GUI.
(2) The Admin group contains information and configuration for all interfaces available for If Basic Admin objects.
(3) The Signal group contains information and configuration for all interfaces available for If Basic Signal objects.
Main OID:
lumIfBasicMIBModule.1.3.6.1.4.1.8708.1.1.46
75
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
75 total| Object Name |
|---|
lumIfBasicMIBModuleThe MIB module for management of basic port objects.
The tables contained in this MIB are:
(1) The General group contains some general attributes as time stamps
and tables sizes.
(2) The If group contains information about the name of the port that
is used in GUI.
(2) The Admin group contains information and configuration for all
interfaces available for If Basic Admin objects.
(3) The Signal group contains information and configuration for all
interfaces available for If Basic Signal objects. MODULE-IDENTITY .1.3.6.1.4.1.8708.1.1.46 |
lumIfBasicConfs OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.1 |
lumIfBasicGroups OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.1.1 |
lumIfBasicCompl OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.1.2 |
lumIfBasicMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.2 |
ifBasicGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.2.1 |
ifBasicGeneralConfigLastChangeTimeThe time when the configuration of the MIB was
last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.1 |
ifBasicGeneralStateLastChangeTimeThe time when the state of the MIB was last
changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.2 |
ifBasicGeneralIfBasicIfTableSizeSize of if tablero Unsigned32 .1.3.6.1.4.1.8708.2.46.2.1.3 |
ifBasicGeneralIfBasicIfConfigLastChangeTimeThe time when the configuration of the
table was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.4 |
ifBasicGeneralIfBasicIfStateLastChangeTimeThe time when the state and/or configuration of
the table was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.5 |
ifBasicGeneralIfBasicAdminTableSizeSize of admin tablero Unsigned32 .1.3.6.1.4.1.8708.2.46.2.1.6 |
ifBasicGeneralIfBasicAdminConfigLastChangeTimeThe time when the configuration of the table was
last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.7 |
ifBasicGeneralIfBasicAdminStateLastChangeTimeThe time when the state and/or configuration of
the table was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.8 |
ifBasicGeneralIfBasicSignalTableSizeSize of signal tablero Unsigned32 .1.3.6.1.4.1.8708.2.46.2.1.9 |
ifBasicGeneralIfBasicSignalConfigLastChangeTimeThe time when the configuration of the table was
last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.10 |
ifBasicGeneralIfBasicSignalStateLastChangeTimeThe time when the state and/or configuration of
the table was last changed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.1.11 |
ifBasicIfList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.2.2 |
ifBasicIfTableThe if basic if interface list. SEQUENCE OF IfBasicIfEntry .1.3.6.1.4.1.8708.2.46.2.2.1 |
ifBasicIfEntryAn entry in the ifBasic if list. IfBasicIfEntry .1.3.6.1.4.1.8708.2.46.2.2.1.1 |
ifBasicIfIndexAn index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.46.2.2.1.1.1 |
ifBasicIfNameThe management name of the interface, for example
'client:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.ro MgmtNameString .1.3.6.1.4.1.8708.2.46.2.2.1.1.2 |
ifBasicIfTxSignalStatusThe state for outgoing (TX) signal
of the interface.
down - A major fault has occurred.
degraded - The signal quality is impaired.
up - The signal is OK.ro SignalStatusWithNA .1.3.6.1.4.1.8708.2.46.2.2.1.1.3 |
ifBasicIfRxSignalStatusThe state for incoming (RX) signal
of the interface.
down - A major fault has occurred.
degraded - The signal quality is impaired.
up - The signal is OK.ro SignalStatusWithNA .1.3.6.1.4.1.8708.2.46.2.2.1.1.4 |
ifBasicIfUpIdIdentity in the UP for the interface. The upId is used internally between CU and
TU to define a certain interface in the TU.ro Unsigned32 .1.3.6.1.4.1.8708.2.46.2.2.1.1.5 |
ifBasicIfAidThe access identifier (AID) of the interface.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.2.1.1.6 |
ifBasicIfPhysicalLocationThe physical location of the if.
The format is according to GR-833.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8708.2.46.2.2.1.1.7 |
ifBasicAdminList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.2.3 |
ifBasicAdminTableThe if basic admin interface list. SEQUENCE OF IfBasicAdminEntry .1.3.6.1.4.1.8708.2.46.2.3.1 |
ifBasicAdminEntryAn entry in the ifBasic admin list. IfBasicAdminEntry .1.3.6.1.4.1.8708.2.46.2.3.1.1 |
ifBasicAdminIndexAn index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.46.2.3.1.1.1 |
ifBasicAdminNameThe management name of the interface, for example
'admin:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.ro MgmtNameString .1.3.6.1.4.1.8708.2.46.2.3.1.1.2 |
ifBasicAdminDescrUser configurable label.rw DisplayStringWithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.3 |
ifBasicAdminSubrackThe subrack of the physical port that this interface is bound to.rw Unsigned32WithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.4 |
ifBasicAdminSlotThe slot of the physical port that this interface is bound to.rw Unsigned32WithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.5 |
ifBasicAdminTxPortThe transmitting physical port that this interface is bound to.rw Unsigned32WithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.6 |
ifBasicAdminRxPortThe receiving physical port that this interface is bound to.rw Unsigned32WithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.7 |
ifBasicAdminAdminStatusThe administrative state of the ifBasic interface.
down - The interface is de-activated.
service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-configuration. When service is concluded
adminStatus should be set to 'up' again. Note that
there is no difference between 'up' and 'service',
if no alarms can be raised from this object.
up - The interface will be activated when
available. Alarms are not suppressed.rw AdminStatusWithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.8 |
ifBasicAdminOperStatusThe operational state for the interface.
notPresent - The interface is not available.
down - The interface is de-activated or there are
faults preventing its transition to the 'up' state.
up - The interface is active.ro OperStatusWithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.9 |
ifBasicAdminAutoAlarmEnableStatusThe state of auto alarm enable for the interface.
suppressTrxAndSignal - Both signal alarms and trx alarms are suppressed
suppressSignal - Only signal alarms are suppressed
suppressNone - Neither trx nor signal alarms
are suppressedro AutoAlarmStatus .1.3.6.1.4.1.8708.2.46.2.3.1.1.10 |
ifBasicAdminAutoAlarmEnableResetWhen the attribute is set to reset the auto-alarm enable function
is re-initialised. Then the attribute is set to normal again
automatically.
reset - Re-initialises the auto-alarm enable function
normal - The auto-alarm enable function is in normal statero ResetWithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.11 |
ifBasicAdminInterfaceStatusThe status of the traffic interface.
outOfService - No PM and no alarms.
autoInService - No PM and no alarms. Changes to 'inService' when OK.
inService - Reports PM and alarms.
maintenance - Maintenance mode.ro InterfaceStatus .1.3.6.1.4.1.8708.2.46.2.3.1.1.12 |
ifBasicAdminIfNoThe physical interface number of the actual multi-connector port.rw Unsigned32WithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.13 |
ifBasicAdminIfTypeType of interface (Individual or bundled).rw InterfaceType .1.3.6.1.4.1.8708.2.46.2.3.1.1.14 |
ifBasicAdminNotAvailableForUseIs the interface not available for use.
The interface may be created in order to show some
physical properties but may otherwise be unavailable
for service depending on setup and available resources.ro TruthValueWithNA .1.3.6.1.4.1.8708.2.46.2.3.1.1.15 |
ifBasicSignalList OBJECT IDENTIFIER .1.3.6.1.4.1.8708.2.46.2.4 |
ifBasicSignalTableThe if basic signal interface list. SEQUENCE OF IfBasicSignalEntry .1.3.6.1.4.1.8708.2.46.2.4.1 |
ifBasicSignalEntryAn entry in the ifBasic signal list. IfBasicSignalEntry .1.3.6.1.4.1.8708.2.46.2.4.1.1 |
ifBasicSignalIndexAn index assigned to each entry.ro Unsigned32 .1.3.6.1.4.1.8708.2.46.2.4.1.1.1 |
ifBasicSignalNameThe management name of the interface, for example
'signal:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.ro MgmtNameString .1.3.6.1.4.1.8708.2.46.2.4.1.1.2 |
ifBasicSignalSignalStructureThe signal structure used. Bitfield 64 bit wide. For internal use.
Bit 0 tells if mib ifBasicPhysicalTrx is loaded,
bit 1 ifBasicOpticalTranssection, etc according to list below.
Add new items last.
ifPhysicalTrx
ifOpticalTranssection
ifOpticalChannel
ifOpticalDigitalSignalRate
ifEthPhysical
ifEthMac
ifOtnOdu
ifOtnOtu
ifOtnOpu
ifOtnMonSm
ifOtnMonPm
ifOtnMonTcm
ifOtnMonTrace
ifSdhRs
ifSdhMs
ifSonetSection
ifSonetLine
ifPerfFec
ifPerfAdmin
ifPerfG826
ifPerfL2Error
ifPerfL1
ifPerfL0
ifOpticalFec
ifFcPhysical
ifOtnTp
ifOpticalTransportLaneCarrier
ifOpticalTransportLaneCarrierGroup
ifPerfL2Stat
ifIwdmRs
ifIwdmMS
ifAmplifierAmplifier
ifAmplifierModule
ifAmplifierRaman
ifAmplifierEdfa
ifIwdmPath
ifFhCpri
ifFhObsai
ifPhysicalCage
ifEthRsFec
ifPerfDelay
ifOtdrro Counter64 .1.3.6.1.4.1.8708.2.46.2.4.1.1.3 |
ifBasicSignalSignalFormatThe signal format.rw SignalFormat .1.3.6.1.4.1.8708.2.46.2.4.1.1.4 |
ifBasicSignalFarEndLoopbackTerminatingLayerThe layer where the far end loopback (a.k.a.
terminal loopback for a client interface and
facility loopback for a line interface) is done.
This is coded in a bitmaskro Layer .1.3.6.1.4.1.8708.2.46.2.4.1.1.5 |
ifBasicSignalFarEndLoopbackThe far end loopback (a.k.a. terminal loopback for
a client interface and facility loopback for a line
interface) setting.
disabled - Far end loopback is not set. This is the
default setting.
enabled - Far end loopback is set.rw EnabledDisabledWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.6 |
ifBasicSignalFarEndLoopbackTimeoutTimeout for far end loopback (a.k.a. terminal
loopback for a client interface and facility
loopback for a line interfac) to make sure
connection to node is not lost if ppp link is
broken. The unit is minutes. The value 0 is used in
SNMP to indicate that the setting will last forever.
Note! This attribute is not saved in backup,
meaning the loopback will be set to disabled
when rebooting CU.rw Time7200min .1.3.6.1.4.1.8708.2.46.2.4.1.1.7 |
ifBasicSignalNearEndLoopbackTerminatingLayerThe layer where the near end loopback (a.k.a.
terminal loopback for a line interface and facility
loopback for a client interface) is done.
This is coded in a bitmask.ro Layer .1.3.6.1.4.1.8708.2.46.2.4.1.1.8 |
ifBasicSignalNearEndLoopbackThe near end loopback (a.k.a. terminal
loopback for a line interface and facility loopback
for a client interface) setting.
disabled - Near end loopback is not set. This is the
default setting.
enabled - Near end loopback is set.rw EnabledDisabledWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.9 |
ifBasicSignalNearEndLoopbackTimeoutTimeout for near end loopback (a.k.a. terminal
loopback for a line interface and facility loopback
for a client interface) to make sure connection to
node is not lost if ppp link is broken. The unit is
minutes. The value 0 is used in SNMP to indicate
that the setting will last forever.
Note! This attribute is not saved in backup,
meaning the loopback will be set to disabled
when rebooting CU.rw Time7200min .1.3.6.1.4.1.8708.2.46.2.4.1.1.10 |
ifBasicSignalFarEndLoopbackEnabledFar end end loopback (a.k.a. terminal loopback for
a client interface and facility loopback for a line
interface) is enabled.
alarm: Far end loopback is enabled.
ok: Far end loopback is disabled.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.11 |
ifBasicSignalNearEndLoopbackEnabledNear end end loopback (a.k.a. terminal loopback for
a line interface and facility loopback for a client
interface) is enabled.
alarm: Near end loopback is enabled.
ok: Near end loopback is disabled.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.12 |
ifBasicSignalOpticalLayerMappingThe optical layer mapping.rw OpticalLayerMappingType .1.3.6.1.4.1.8708.2.46.2.4.1.1.13 |
ifBasicSignalConfigurationMismatchThe inserted transceiver does not support the
configuration of the optical layer mapping.
alarm: A transceiver with other supported optical layer
mapping than the requested mapping is inserted.
ok: The transceiver with the non-requested optical
layer mapping is removed, or the object is reconfigured.rodeprecated FaultStatusWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.14 |
ifBasicSignalActualOpticalLayerMappingThe actual optical layer mapping.ro OpticalLayerMappingType .1.3.6.1.4.1.8708.2.46.2.4.1.1.15 |
ifBasicSignalSpeedThe expected signal bit rate in units of
10,000 bits (0.01 Mb) per second.rw Unsigned32WithNA (61440..1402500|2147483647) .1.3.6.1.4.1.8708.2.46.2.4.1.1.16 |
ifBasicSignalDirectionThe direction in which this object is
referred to.
rx - In bound direction. (1)
tx - out bound direction. (2)
biDir - the interface has one connector used for both rx and tx. (3)
txRx - the interface has two connectors one for tx and one for rx. (4)
Not Available - the direction is not available.ro SignalDirection .1.3.6.1.4.1.8708.2.46.2.4.1.1.17 |
ifBasicSignalFormatConfigurableThis atttribute indicates if the interface is format configurable or not
true - The interface is format configurable
false - The interface is not format configurablero Enumeration .1.3.6.1.4.1.8708.2.46.2.4.1.1.18 |
ifBasicSignalFormatConfigurationSharedWithInterfaceThis attribute specifies whether this object instances shares the format
configuration with another object instance.
value == 0: it is not shared
value != 0: it is shared with the interface object with index = value in IfBasicIfEntry
If it is shared, it means that updating the format (and optionally speed)
will affect the configuration of the other object instancero Unsigned32WithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.19 |
ifBasicSignalPhysicalLayerMappingThe expected physical layer mapping.rw PhysicalLayerMappingType .1.3.6.1.4.1.8708.2.46.2.4.1.1.20 |
ifBasicSignalFacilityLoopbackThe facility loopback setting. Rx is looped to Tx.
The purpose of facility loopback is to test
the line interface termination.
disabled - Facility loopback is not set. This is the
default setting.
enabled - Facility loopback is set.rw EnabledDisabledWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.21 |
ifBasicSignalFacilityLoopbackTimeoutTimeout for facility loopback to make sure
connection to node is not lost if ppp link is
broken. The unit is minutes.
Note! This attribute is not saved in backup,
meaning the loopback will be set to disabled
when rebooting CU.rw Time7200minNo0 .1.3.6.1.4.1.8708.2.46.2.4.1.1.22 |
ifBasicSignalFacilityLoopbackEnabledFacility loopback is enabled.
alarm: Facility loopback is enabled.
ok: Facility loopback is disabled.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.23 |
ifBasicSignalTerminalLoopbackThe terminal loopback setting. Tx is looped to Rx.
The purpose of a terminal loopback is to test
the path through the equipment (a cross-connect,
mux/demux stage, or similar) and execute the loop
close to the outgoing interface.
disabled - Terminal loopback is not set. This is the
default setting.
enabled - Terminal loopback is set.rw EnabledDisabledWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.24 |
ifBasicSignalTerminalLoopbackTimeoutTimeout for terminal loopback to make sure connection to
node is not lost if ppp link is broken. The unit is
minutes.
Note! This attribute is not saved in backup,
meaning the loopback will be set to disabled
when rebooting CU.rw Time7200minNo0 .1.3.6.1.4.1.8708.2.46.2.4.1.1.25 |
ifBasicSignalTerminalLoopbackEnabledTerminal loopback is enabled.
alarm: Terminal loopback is enabled.
ok: Terminal loopback is disabled.ro FaultStatusWithNA .1.3.6.1.4.1.8708.2.46.2.4.1.1.26 |
ifBasicSignalConnectorTypeThe connector type.ro ConnectorType .1.3.6.1.4.1.8708.2.46.2.4.1.1.27 |