LINK-BUNDLING-MIB
AI MIB Summary
The LINK-BUNDLING-MIB manages MPLS Traffic Engineering link bundling parameters, specifically monitoring aggregated link capacity, individual member link states, and bundle configuration attributes to optimize path selection and resource utilization. It enables the collection of metrics regarding bundle membership, administrative status, and operational state for interfaces participating in MPLS link aggregation.
This MIB contains managed object definitions for MPLS traffic engineering link bundling as defined in: Kompella, K., Rekhter, Y., Berger, L., Link Bundling in MPLS Traffic Engineering Internet Draft <draft-ietf-mpls-bundling-04.txt>, July 2002.
Main OID:
linkBundlingMIB.1.3.6.1.4.1.3727.20.20.3.1.1
71
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
71 total| Object Name |
|---|
linkBundlingMIBThis MIB contains managed object definitions for
MPLS traffic engineering link bundling as
defined in: Kompella, K., Rekhter, Y., Berger, L.,
Link Bundling in MPLS Traffic Engineering
Internet Draft <draft-ietf-mpls-bundling-04.txt>,
July 2002. MODULE-IDENTITY .1.3.6.1.4.1.3727.20.20.3.1.1 |
linkBundlingNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.1.0 |
linkBundleMismatchThis notification is generated when a mismatch is found on a
bundled link. Such mismatch can be detected for instance if one
of the traffic engineering parameters is not consistent across
all TE links within a bundled link (resource class,
OSPF link type, etc.). NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.1.0.1 |
linkBundlingObjects OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.1.1 |
teLinkTableThis table specifies the grouping of component links into
TE links and grouping of TE links into bundled links. SEQUENCE OF TeLinkEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.1 |
teLinkEntryAn entry in this table exists for each ifEntry with an
ifType of teLink(TBD), i.e. for every TE link. An ifEntry
in the ifTable must exist before a teLinkEntry is created with
the corresponding ifIndex. If a TE link entry in the ifTable is
destroyed, then so is the corresponding entry in the
teLinkTable. The administrative and operational status values
are controlled from the ifEntry. If the link is unnumbered,
ifIndex is also used as the outgoing interface identifier. TeLinkEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1 |
teLinkIpAddrTypeFor IPv4 and IPv6 numbered links, this object represents the
IP address type associated with the TE link. For
unnumbered links, a value of unknown(0) must be used.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.1 |
teLinkIpAddrFor IPv4 and IPv6 numbered links, this object represents the
IP address associated with the TE link.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.2 |
teLinkRemoteIpAddrThe remote IP address associated with the TE link (IPv4 and
IPv6 numbered links).rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.3 |
teLinkMetricThe traffic engineering metric for the TE link is
derived from its component links. All component links
within the TE link must have the same traffic
engineering metric.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.4 |
teLinkMuxCapabilityThis attribute specifies link multiplex capability of the
TE link, which is derived from its component links. All
component links within the same TE link must have the
same link multiplex capability.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.5 |
teLinkProtectionTypeThis attribute specifies link protection type of the
TE link.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.6 |
teLinkWorkingPriorityThis object represents a priority value such that a new
connection with a higher priority, i.e. numerically lower than
this value, is guaranteed to be setup on a primary link and
not on a secondary link.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.7 |
teLinkResourceClassThis attribute specifies the TE link resource class.
The resource class is a 32 bit bitfield. The resource class for
a link bundle is derived from the resource class of its
TE links. All TE links within a link bundle must have the
same resource class.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.8 |
teLinkIncomingIfIdFor unnumbered links, the incoming interface is set to the
outgoing interface identifier chosen by the neighboring LSR
for the reverse link corresponding to this TE link.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.9 |
teLinkOutgoingIfIdIf the link is unnumbered, the outgoing interface identifier is
set to the outgoing interface identifier chosen for the TE link
by the advertising LSR.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.10 |
teLinkFloodingThis object only has significance for link bundles which
encoding type is not clear. For these link bundles, this object
identifies the TE link on which to restrict flooding. If the
value is zero, then flooding must be done on all TE links
within the link bundle.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.11 |
teLinkRowStatusThis variable is used to create, modify, and/or
delete a row in this table. All read-create objects
can only be changed when teLinkRowStatus is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.12 |
teLinkStorageTypeThe storage type for this conceptual row in the
teLinkTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.1.1.13 |
teLinkDescriptorTableThis table specifies the link descriptors associated with the
TE links. SEQUENCE OF TeLinkDescriptorEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.2 |
teLinkDescriptorEntryAn entry in this table is created for every TE link descriptor.
An ifEntry in the ifTable must exist before a
teLinkDescriptorEntry using the same ifIndex is created.
If a TE link entry in the ifTable is destroyed, then so are all
entries in the teLinkDescriptorTable that use the ifIndex of
this TE link. TeLinkDescriptorEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1 |
teLinkDescriptorIdThis object specifies the link descriptor identifier. Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1.1 |
teLinkEncodingTypeThis attribute specifies the TE link encoding type.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1.2 |
teLinkDescrPriorityThis object specifies the lowest priority at which that link
encoding type is available.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1.3 |
teLinkMinReservableBandwidthThis attribute specifies the minimum reservable bandwidth on
the TE link. This is derived from the union of the
minimum reservable bandwidth of all the component links
associated with the TE link that can be used to carry
live traffic. This value is an estimate in units of 1,000 bits
per second.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1.4 |
teLinkMaxReservableBandwidthThis attribute specifies the maximum reservable bandwidth on
the TE link. This is the union of the maximum reservable
bandwidth of all the component links within the
TE link that can be used to carry live traffic. This value
is an estimate in units of 1,000 bits per second.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1.5 |
teLinkDescrRowStatusThis variable is used to create, modify, and/or
delete a row in this table. All read-create objects
can only be changed when teLinkDescrRowStatus is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1.6 |
teLinkDescrStorageTypeThe storage type for this conceptual row in the
teLinkDescriptorTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.2.1.7 |
teLinkOspfTeTableThis table specifies the OSPF traffic engineering information
associated with TE links. SEQUENCE OF TeLinkOspfTeEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.3 |
teLinkOspfTeEntryIf OSPF is enabled, an entry in this table is created for
every TE link. TeLinkOspfTeEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.3.1 |
teLinkOspfLinkTypeThis attribute specifies the OSPF link type for the TE link.
All TE links within the same bundle must have the same
link type.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.3.1.1 |
teLinkOspfLinkIdOn point-to-point link, the link identifier is the Router ID
of the neighbor. For bundled link, is derived from the link
identifier associated with its TE links.rw RouterID (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.1.1.3.1.2 |
teLinkSrlgTableThis table specifies the SRLGs associated with TE links. SEQUENCE OF TeLinkSrlgEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.4 |
teLinkSrlgEntryAn entry in this table contains information about a
SRLG associated with a TE link.
An ifEntry in the ifTable must exist before a
teLinkSrlgEntry using the same ifIndex is created.
If a TE link entry in the ifTable is destroyed, then so are all
entries in the teLinkSrlgTable that use the ifIndex of
this TE link. TeLinkSrlgEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.4.1 |
srlgThis identifies a SRLG supported by the TE link. Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.4.1.1 |
srlgRowStatusThis variable is used to create, modify, and/or
delete a row in this table. All read-create objects
can only be changed when srlgRowStatus is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.4.1.2 |
srlgStorageTypeThe storage type for this conceptual row in the
teLinkSrlgTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.4.1.3 |
teLinkBandwidthTableThis table specifies the priority-based bandwidth table
for TE links. SEQUENCE OF TeLinkBandwidthEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.5 |
teLinkBandwidthEntryAn entry in this table contains information about
the priority-based bandwidth of TE links. An ifEntry in the
ifTable must exist before a teLinkBandwidthEntry using the
same ifIndex is created. If a TE link entry in the ifTable
is destroyed, then so are all entries in the teLinkBandwidthTable
that use the ifIndex of this TE link. TeLinkBandwidthEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.5.1 |
teLinkPriorityThis attribute specifies the priority. It should be mapped
to a number between 0 and 7 Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.5.1.1 |
teLinkUnreservedBandwidthThis attribute specifies the TE link unreserved
bandwidth at priority p. It is the sum of the unreserved
bandwidths at priority p of all component links associated
with the TE link (excludes all links that are strictly
used as protecting links). This value is an estimate in units
of 1,000 bits per second.ro Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.5.1.2 |
teLinkMaximumLspBandwidthThis attribute specifies the TE link maximum
LSP bandwidth at priority p. It is the maximum of all
maximum LSP bandwidth at priority p of the component links
associated with the TE link (excludes all links that are
strictly used as protecting links). This value is an estimate
in units of 1,000 bits per second.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.5.1.3 |
teLinkBandwidthRowStatusThis variable is used to create, modify, and/or
delete a row in this table. All read-create objects
can only be changed when teLinkBandwidthRowStatus is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.5.1.4 |
teLinkBandwidthStorageTypeThe storage type for this conceptual row in the
teLinkBandwidthTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.5.1.5 |
componentLinkTableThis table specifies the component link parameters. SEQUENCE OF ComponentLinkEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.6 |
componentLinkEntryAn entry in this table exists for each ifEntry that represents
a component link. An ifEntry must exist in the ifTable
before a componentLinkEntry is created with the
corresponding ifIndex. If an entry representing a component
link is destroyed in the ifTable, then so is the
corresponding entry in the componentLinkTable. The
administrative and operational status values are controlled
from the ifEntry. ComponentLinkEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.6.1 |
componentLinkMuxCapabilityThis attribute specifies link multiplexing capabilities of the
component link.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.6.1.1 |
componentLinkPreferredProtectionThis attribute specifies whether this component link is
a primary or secondary entity.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.6.1.2 |
componentLinkCurrentProtectionThis attribute specifies whether this component link is
currently used as primary or secondary link.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.6.1.3 |
componentLinkRowStatusThis variable is used to create, modify, and/or
delete a row in this table. All read-create objects
can only be changed when componentLinkRowStatus is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.6.1.4 |
componentLinkStorageTypeThe storage type for this conceptual row in the
componentLinkTable. Conceptual rows having the value
'permanent' need not allow write-access to any
columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.6.1.5 |
componentLinkDescriptorTableThis table specifies the link descriptors associated with the
component links. SEQUENCE OF ComponentLinkDescriptorEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.7 |
componentLinkDescriptorEntryAn entry in this table is created for every component link
descriptor. An ifEntry in the ifTable must exist before a
componentLinkDescriptorEntry using the same ifIndex is created.
If a component link entry in the ifTable is destroyed,
then so are all entries in the componentLinkDescriptorTable
that use the ifIndex of this component link. ComponentLinkDescriptorEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1 |
componentLinkDescrIdThis object specifies the link descriptor identifier. Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1.1 |
componentLinkEncodingTypeThis attribute specifies the component link encoding type.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1.2 |
componentLinkDescrPriorityThis object specifies the lowest priority at which that link
encoding type is available for the component link.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1.3 |
componentLinkMinReservBandwidthThis attribute specifies the minimum reservable bandwidth on
the component link. This value is an estimate
in units of 1,000 bits per second.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1.4 |
componentLinkMaxReservBandwidthThis attribute specifies the maximum reservable bandwidth on
the component link. This value is an estimate
in units of 1,000 bits per second.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1.5 |
componentLinkDescrRowStatusThis variable is used to create, modify, and/or
delete a row in this table. All read-create objects
can only be changed when componentLinkDescrRowStatus
is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1.6 |
componentLinkDescrStorageTypeThe storage type for this conceptual row in the
componentLinkDescriptorTable. Conceptual rows
having the value 'permanent' need not allow write-access
to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.7.1.7 |
componentLinkBandwidthTableThis table specifies the priority-based bandwidth
for component links. SEQUENCE OF ComponentLinkBandwidthEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.8 |
componentLinkBandwidthEntryAn entry in this table contains information about
the priority-based bandwidth on component links.
An ifEntry in the ifTable must exist before a
componentLinkBandwidthEntry using the same ifIndex is
created. If a component link entry in the ifTable is
destroyed, then so are all entries in the
componentLinkBandwidthTable that use the ifIndex of
this component link. ComponentLinkBandwidthEntry .1.3.6.1.4.1.3727.20.20.3.1.1.1.8.1 |
componentLinkPriorityThis attribute specifies the priority. It should be mapped
to a number between 0 and 7. Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.8.1.1 |
componentLinkUnreservedBandwidthThis attribute specifies the component link unreserved
bandwidth at priority p. This value is an estimate
in units of 1,000 bits per second.ro Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.8.1.2 |
componentLinkMaximumLspBandwidthThis attribute specifies the component link maximum
LSP bandwidth at priority p. This value is an estimate
in units of 1,000 bits per second.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.1.1.8.1.3 |
componentLinkBandwidthRowStatusThis variable is used to create, modify, and/or
delete a row in this table. All read-create objects can only
be changed when componentLinkBandwidthRowStatus is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.8.1.4 |
componentLinkBwStorageTypeThe storage type for this conceptual row in the
componentLinkBandwidthTable. Conceptual rows
having the value 'permanent' need not allow write-access
to any columnar object in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.8.1.5 |
linkBundlingNotifEnableIf this object is true, then it enables the
generation of the link bundling notifications,
otherwise these notifications are not emitted.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.1.1.9 |
linkBundlingConformance OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.1.2 |
linkBundlingGroups OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.1.2.1 |
linkBundlingCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.1.2.2 |