JETDIRECT3-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
277
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
277 total| Object Name |
|---|
hp OBJECT IDENTIFIER .1.3.6.1.4.1.11 |
nm OBJECT IDENTIFIER .1.3.6.1.4.1.11.2 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3 |
sysDescrA textual description of the entity. This value
should include the full name and version
identification of the system's hardware type,
software operating-system, and networking
software. It is mandatory that this only contain
printable ASCII characters.ro DisplayString .1.3.6.1.4.1.11.2.3.1 |
sysObjectIDThe vendor's authoritative identification of the
network management subsystem contained in the
entity. This value is allocated within the SMI
enterprises subtree (1.3.6.1.4.1) and provides an
easy and unambiguous means for determining `what
kind of box' is being managed. The value for this
device is constructed by appending the peripheral
attribute class npNpiPaeClass to the sysObjId base:
.1.3.6.1.4.1.11.2.3.9. See description of npNpiPaeClass
below.ro OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.2 |
sysUpTimeThe time (in hundredths of a second) since the
network management portion of the system was last
re-initialized.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.3 |
sysContactThe textual identification of the contact person
for this managed node, together with information
on how to contact this person.rw DisplayString .1.3.6.1.4.1.11.2.3.4 |
sysNameAn administratively-assigned name for this
managed node. By convention, this is the node's
fully-qualified domain name.rw DisplayString .1.3.6.1.4.1.11.2.3.5 |
sysLocationThe physical location of this node (e.g.,
`telephone closet, 3rd floor'). This string
can be set using two different methods. The first
is through the tftp config file for the TCP solution.
The other is using SNMP over any of the protocols.
This value is saved in NVRAM. Using SNMP to set this
object will cause the tftp version to be overwritten.
If this object is set using SNMP then the tftp
version from the tftp config file will NOT cause an
overwrite at boot time.rw DisplayString .1.3.6.1.4.1.11.2.3.6 |
sysServicesA value which indicates the set of services that
this entity primarily offers.
The value is a sum. This sum initially takes the
value zero, Then, for each layer, L, in the range
1 through 7, that this node performs transactions
for, 2 raised to (L - 1) is added to the sum.ro INTEGER .1.3.6.1.4.1.11.2.3.7 |
net-peripheral OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9 |
net-printer OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.1 |
generalDeviceStatus OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.1.1 |
gdStatusBytesThe number of valid bytes in the gdStatusEntry
array.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.1 |
gdStatusEntryThe networked peripheral's 32 octet status
information that is shared between the peripheral
and the LAN card. OCTET STRING .1.3.6.1.4.1.11.2.3.9.1.1.2 |
gdStatusLineStateThis describes the line state of the peripheral.
When non-zero, the peripheral is off-line. When
zero the peripheral is on-line.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.1 |
gdStatusPaperStateThis describes the state of the paper on the peripheral.
When non-zero, the peripheral has a paper problem. When
zero, the peripheral does not have a paper problem.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.2 |
gdStatusInterventionStateThis describes the intervention state of the
peripheral. When non-zero, the peripheral requires
human intervention to continue working. When
zero, it requires no assistance.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.3 |
gdStatusNewModeThis indicates to which read channel state the
card should move. When non-zero, the card should
indicate that the read channel is idle. When zero,
the card should indicate that the read channel is
operating. This object is Lan Manager io channel
specific. It is kept here for backward compatibility.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.4 |
gdStatusConnectionTerminationAckThis indicates whether the peripheral is waiting for
the Connection termination ACK. When non-zero, it
is waiting. When zero, it is not waiting.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.5 |
gdStatusPeripheralErrorThis is the error code from the peripheral.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.6 |
gdStatusPaperOutThis indicates that the peripheral is out of paper.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER -- OFF(0), -- PAPER-OUT-OR-PAPER-MOUNT(1), -- MANUAL-PAPER-FEED-NEEDED(2) .1.3.6.1.4.1.11.2.3.9.1.1.2.8 |
gdStatusPaperJamThis indicates that the peripheral has a paper jam.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER -- OFF(0), -- PAPER-JAM(1) .1.3.6.1.4.1.11.2.3.9.1.1.2.9 |
gdStatusTonerLowThis indicates that the peripheral has a low toner condition.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER -- OFF(0), -- TONER-LOW(1), -- NO-TONER-CARTRIDGE(2) .1.3.6.1.4.1.11.2.3.9.1.1.2.10 |
gdStatusPagePuntThis indicates that the peripheral did not receive data fast
enough to keep up with the print engine when generating a page.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.11 |
gdStatusMemoryOutThis indicates that the peripheral did not have enough memory
to render an image on a page.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.12 |
gdStatusIoActiveThis indicates that the peripheral is processing data from
this I/O interface card.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.13 |
gdStatusBusyThis indicates that the peripheral is busy processing
print/plot data.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.14 |
gdStatusWaitThis indicates that the peripheral is waiting for print/plot
data to process.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.15 |
gdStatusInitializeThis indicates that the peripheral is initializing or
warming up.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER -- OFF(0), -- INITIALIZING(1), -- WARM-UP(2) .1.3.6.1.4.1.11.2.3.9.1.1.2.16 |
gdStatusDoorOpenThis indicates that the peripheral cover or door is open.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.17 |
gdStatusPrintingThis indicates that the peripheral is printing or otherwise
marking or moving paper.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER -- OFF(0), -- ORDINARY-PAGE(1), -- TEST-FONTS-CONFIG-OR-START-PAGE(2) .1.3.6.1.4.1.11.2.3.9.1.1.2.18 |
gdStatusPaperOutputThis indicates that the peripheral has a paper output problem
such as the output storage bin being full.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0).ro INTEGER -- OFF(0), -- OUTPUT-STORAGE-FULL(1) .1.3.6.1.4.1.11.2.3.9.1.1.2.19 |
gdStatusReservedThis is the reserved area that is not currently
used, but will allow for growth within the gdStatusEntry table.ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.1.1.2.20 |
gdStatusNovBusyThis indicates if this channel is active. If the
value is 0 then this channel is active or the peripheral
is idle. If this value is non-zero then another channel
is active. This is the Novell io channelro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.21 |
gdStatusLlcBusyThis indicates if this channel is active. If the
value is 0 then this channel is active or the peripheral
is idle. If this value is non-zero then another channel
is active. This is the LLC io channelro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.22 |
gdStatusTcpBusyThis indicates if this channel is active. If the
value is 0 then this channel is active or the peripheral
is idle. If this value is non-zero then another channel
is active. This is the TCP io channelro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.23 |
gdStatusAtBusyThis indicates if this channel is active. If the
value is 0 then this channel is active or the peripheral
is idle. If this value is non-zero then another channel
is active. This is the Apple talk io channelro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.2.24 |
gdStatusDisplayThe string diplayed on the peripheral front panel.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this is always a zero length string.ro DisplayString .1.3.6.1.4.1.11.2.3.9.1.1.3 |
gdStatusJobNameThe current job name set by the peripheral.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this is always a zero length string.ro DisplayString .1.3.6.1.4.1.11.2.3.9.1.1.4 |
gdStatusSourceA string indicating the name of the physical port or protocol
the printer is currently getting data from.ro DisplayString .1.3.6.1.4.1.11.2.3.9.1.1.5 |
gdStatusPapstatusA string indicating the Appletalk papstatus response.ro DisplayString .1.3.6.1.4.1.11.2.3.9.1.1.6 |
gdStatusIdA formatted string describing this peripheral.ro DisplayString .1.3.6.1.4.1.11.2.3.9.1.1.7 |
gdStatusDisplayCodeThis is the display code that the peripheral uses
to tell the card what type of display the front
panel of the printer is.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.8 |
gdStatusNlsCodeThis value is the representation of what native
language the printer is in currently.ro INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.9 |
gdStatusJobTimeoutThis value represents (in seconds) the maximum time of
inactivity which must elapse before the JetDirect card
switches from the current network protocol to another when
a normal end of job is not detected.rw INTEGER .1.3.6.1.4.1.11.2.3.9.1.1.10 |
gdStatusPjlUstatusThis object will enable/disable PJL ustatus.rw INTEGER -- DISABLED(0), -- ENABLED(1) .1.3.6.1.4.1.11.2.3.9.1.1.11 |
netPrinterType OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.1.2 |
netPML OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4 |
netPMLmgmt OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2 |
device OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1 |
destination-subsystem OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4 |
print-engine OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1 |
status-prt-eng OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2 |
interface OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4 |
ieee8023Mac OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.1 |
ieee8025Mac OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.2 |
npCard OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3 |
npSys OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.1 |
npConns OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.4 |
npCfg OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.5 |
npTcp OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.6 |
npCtl OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.7 |
npNpi OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.8 |
npElt OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.9 |
npIpx OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.10 |
npDm OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.11 |
llcconstategroup OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.12 |
npPort OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.13 |
npXip OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.14 |
npCRC OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.15 |
npDhcp OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.16 |
npScan OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.17 |
npWeb OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.4.3.18 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.13 |
trapDest OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.13.1 |
icf OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14 |
hpicfAdmin OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10 |
hpicfDomains OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.1 |
hpicfLLCDomain OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.10.1.1 |
hpicfObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11 |
hpicfCommon OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1 |
hpicfChain OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.1 |
hpicfNBPDomain OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.2 |
hpicfDownload OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.1.3 |
snmpAccess OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.15 |
community OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.15.1 |
hpWebMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.36 |
hpHttpMgMod OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.36.1 |
hpHttpMgObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.36.1.1 |
hpHttpMgDefaults OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.36.1.1.1 |
gdStatusLaaSupportThis value represents what protocols Locally Administered
addressing is supported over. This is currently 0 for
802.3 cards and 7 for 802.5 cards. LAA is not supported
on 802.3. The value is a mask of bits, 1 for each of the
protocols below.
+
| NA | NA | NA | NA | NA | TCP | LLC | NOV |
+
::={ generalDeviceStatus 12 }
gdPasswords OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
ACCESS read-write
STATUS optional
DESCRIPTIONrw INTEGER .1.3.6.1.4.1.11.2.36.1.1.1.1 |
mib-2 OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1 |
IMPORTS Unknown .1.3.6.1.4.1.3727.20.20.3.1 |
interfaces OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.2 |
ifNumberThe number of network interfaces (regardless of
their current state) present on this system.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.2.1 |
ifTableA list of interface entries. The number of
entries is given by the value of ifNumber. SEQUENCE OF IfEntry .1.3.6.1.4.1.3727.20.20.3.1.2.2 |
ifEntryAn interface entry containing objects at the
subnetwork layer and below for a particular
interface. IfEntry .1.3.6.1.4.1.3727.20.20.3.1.2.2.1 |
ifIndexA unique value for each interface. Its value
ranges between 1 and the value of ifNumber. The
value for each interface must remain constant at
least from one re-initialization of the entity's
network management system to the next re-
initialization.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.1 |
ifDescrA textual string containing information about the
interface. This string should include the name of
the manufacturer, the product name and the version
of the hardware interface.ro DisplayString .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.2 |
ifTypeThe type of interface, distinguished according to
the physical/link protocol(s) immediately `below'
the network layer in the protocol stack.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.3 |
ifMtuThe size of the largest datagram which can be
sent/received on the interface, specified in
octets. For interfaces that are used for
transmitting network datagrams, this is the size
of the largest network datagram that can be sent
on the interface.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.4 |
ifSpeedAn estimate of the interface's current bandwidth
in bits per second. For interfaces which do not
vary in bandwidth or for those where no accurate
estimation can be made, this object should contain
the nominal bandwidth.ro Gauge .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.5 |
ifPhysAddressThe interface's address at the protocol layer
immediately `below' the network layer in the
protocol stack. For interfaces which do not have
such an address (e.g., a serial line), this object
should contain an octet string of zero length.ro OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.6 |
ifAdminStatusThe desired state of the interface. The
testing(3) state indicates that no operational
packets can be passed.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.7 |
ifOperStatusThe current operational state of the interface.
The testing(3) state indicates that no operational
packets can be passed.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.8 |
ifLastChangeThe value of sysUpTime at the time the interface
entered its current operational state. If the
current state was entered prior to the last re-
initialization of the local network management
subsystem, then this object contains a zero
value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.9 |
ifInOctetsThe total number of octets received on the
interface, including framing characters.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.10 |
ifInUcastPktsThe number of subnetwork-unicast packets
delivered to a higher-layer protocol.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.11 |
ifInNUcastPktsThe number of non-unicast (i.e., subnetwork-
broadcast or subnetwork-multicast) packets
delivered to a higher-layer protocol.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.12 |
ifInDiscardsThe number of inbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being deliverable to a
higher-layer protocol. One possible reason for
discarding such a packet could be to free up
buffer space.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.13 |
ifInErrorsThe number of inbound packets that contained
errors preventing them from being deliverable to a
higher-layer protocol.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.14 |
ifInUnknownProtosThe number of packets received via the interface
which were discarded because of an unknown or
unsupported protocol.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.15 |
ifOutOctetsThe total number of octets transmitted out of the
interface, including framing characters.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.16 |
ifOutUcastPktsThe total number of packets that higher-level
protocols requested be transmitted to a
subnetwork-unicast address, including those that
were discarded or not sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.17 |
ifOutNUcastPktsThe total number of packets that higher-level
protocols requested be transmitted to a non-
unicast (i.e., a subnetwork-broadcast or
subnetwork-multicast) address, including those
that were discarded or not sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.18 |
ifOutDiscardsThe number of outbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being transmitted. One
possible reason for discarding such a packet could
be to free up buffer space.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.19 |
ifOutErrorsThe number of outbound packets that could not be
transmitted because of errors.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.20 |
ifOutQLenThe length of the output packet queue (in
packets).ro Gauge .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.21 |
ifSpecificA reference to MIB definitions specific to the
particular media being used to realize the
interface. For example, if the interface is
realized by an ethernet, then the value of this
object refers to a document defining objects
specific to ethernet. If this information is not
present, its value should be set to the OBJECT
IDENTIFIER { 0 0 }, which is a syntatically valid
object identifier, and any conformant
implementation of ASN.1 and BER must be able to
generate and recognize this value.ro OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.2.2.1.22 |
at OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.3 |
atTableThe Address Translation tables contain the
NetworkAddress to `physical' address equivalences.
Some interfaces do not use translation tables for
determining address equivalences (e.g., DDN-X.25
has an algorithmic method); if all interfaces are
of this type, then the Address Translation table
is empty, i.e., has zero entries.deprecated SEQUENCE OF AtEntry .1.3.6.1.4.1.3727.20.20.3.1.3.1 |
atEntryEach entry contains one NetworkAddress to
`physical' address equivalence.deprecated AtEntry .1.3.6.1.4.1.3727.20.20.3.1.3.1.1 |
atIfIndexThe interface on which this entry's equivalence
is effective. The interface identified by a
particular value of this index is the same
interface as identified by the same value of
ifIndex.rodeprecated INTEGER .1.3.6.1.4.1.3727.20.20.3.1.3.1.1.1 |
atPhysAddressThe media-dependent `physical' address.
Setting this object to a null string (one of zero
length) has the effect of invaliding the
corresponding entry in the atTable object. That
is, it effectively dissasociates the interface
identified with said entry from the mapping
identified with said entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.
Accordingly, management stations must be prepared
to receive tabular information from agents that
corresponds to entries not currently in use.
Proper interpretation of such entries requires
examination of the relevant atPhysAddress object.rodeprecated OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.3.1.1.2 |
atNetAddressThe NetworkAddress (e.g., the IP address)
corresponding to the media-dependent `physical'
address.rodeprecated IpAddress .1.3.6.1.4.1.3727.20.20.3.1.3.1.1.3 |
ip OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.4 |
ipForwardingThe indication of whether this entity is acting
as an IP gateway in respect to the forwarding of
datagrams received by, but not addressed to, this
entity. IP gateways forward datagrams. IP hosts
do not (except those source-routed via the host).
Note that for some managed nodes, this object may
take on only a subset of the values possible.
Accordingly, it is appropriate for an agent to
return a `badValue' response if a management
station attempts to change this object to an
inappropriate value.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.1 |
ipDefaultTTLThe default value inserted into the Time-To-Live
field of the IP header of datagrams originated at
this entity, whenever a TTL value is not supplied
by the transport layer protocol.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.2 |
ipInReceivesThe total number of input datagrams received from
interfaces, including those received in error.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.3 |
ipInHdrErrorsThe number of input datagrams discarded due to
errors in their IP headers, including bad
checksums, version number mismatch, other format
errors, time-to-live exceeded, errors discovered
in processing their IP options, etc.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.4 |
ipInAddrErrorsThe number of input datagrams discarded because
the IP address in their IP header's destination
field was not a valid address to be received at
this entity. This count includes invalid
addresses (e.g., 0.0.0.0) and addresses of
unsupported Classes (e.g., Class E). For entities
which are not IP Gateways and therefore do not
forward datagrams, this counter includes datagrams
discarded because the destination address was not
a local address.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.5 |
ipForwDatagramsThe number of input datagrams for which this
entity was not their final IP destination, as a
result of which an attempt was made to find a
route to forward them to that final destination.
In entities which do not act as IP Gateways, this
counter will include only those packets which were
Source-Routed via this entity, and the Source-
Route option processing was successful.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.6 |
ipInUnknownProtosThe number of locally-addressed datagrams
received successfully but discarded because of an
unknown or unsupported protocol.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.7 |
ipInDiscardsThe number of input IP datagrams for which no
problems were encountered to prevent their
continued processing, but which were discarded
(e.g., for lack of buffer space). Note that this
counter does not include any datagrams discarded
while awaiting re-assembly.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.8 |
ipInDeliversThe total number of input datagrams successfully
delivered to IP user-protocols (including ICMP).ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.9 |
ipOutRequestsThe total number of IP datagrams which local IP
user-protocols (including ICMP) supplied to IP in
requests for transmission. Note that this counter
does not include any datagrams counted in
ipForwDatagrams.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.10 |
ipOutDiscardsThe number of output IP datagrams for which no
problem was encountered to prevent their
transmission to their destination, but which were
discarded (e.g., for lack of buffer space). Note
that this counter would include datagrams counted
in ipForwDatagrams if any such packets met this
(discretionary) discard criterion.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.11 |
ipOutNoRoutesThe number of IP datagrams discarded because no
route could be found to transmit them to their
destination. Note that this counter includes any
packets counted in ipForwDatagrams which meet this
`no-route' criterion. Note that this includes any
datagarms which a host cannot route because all of
its default gateways are down.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.12 |
ipReasmTimeoutThe maximum number of seconds which received
fragments are held while they are awaiting
reassembly at this entity.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.13 |
ipReasmReqdsThe number of IP fragments received which needed
to be reassembled at this entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.14 |
ipReasmOKsThe number of IP datagrams successfully re-
assembled.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.15 |
ipReasmFailsThe number of failures detected by the IP re-
assembly algorithm (for whatever reason: timed
out, errors, etc). Note that this is not
necessarily a count of discarded IP fragments
since some algorithms (notably the algorithm in
RFC 815) can lose track of the number of fragments
by combining them as they are received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.16 |
ipFragOKsThe number of IP datagrams that have been
successfully fragmented at this entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.17 |
ipFragFailsThe number of IP datagrams that have been
discarded because they needed to be fragmented at
this entity but could not be, e.g., because their
Don't Fragment flag was set.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.18 |
ipFragCreatesThe number of IP datagram fragments that have
been generated as a result of fragmentation at
this entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.19 |
ipAddrTableThe table of addressing information relevant to
this entity's IP addresses. SEQUENCE OF IpAddrEntry .1.3.6.1.4.1.3727.20.20.3.1.4.20 |
ipAddrEntryThe addressing information for one of this
entity's IP addresses. IpAddrEntry .1.3.6.1.4.1.3727.20.20.3.1.4.20.1 |
ipAdEntAddrThe IP address to which this entry's addressing
information pertains.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.4.20.1.1 |
ipAdEntIfIndexThe index value which uniquely identifies the
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value of ifIndex.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.20.1.2 |
ipAdEntNetMaskThe subnet mask associated with the IP address of
this entry. The value of the mask is an IP
address with all the network bits set to 1 and all
the hosts bits set to 0.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.4.20.1.3 |
ipAdEntBcastAddrThe value of the least-significant bit in the IP
broadcast address used for sending datagrams on
the (logical) interface associated with the IP
address of this entry. For example, when the
Internet standard all-ones broadcast address is
used, the value will be 1. This value applies to
both the subnet and network broadcasts addresses
used by the entity on this (logical) interface.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.20.1.4 |
ipAdEntReasmMaxSizeThe size of the largest IP datagram which this
entity can re-assemble from incoming IP fragmented
datagrams received on this interface.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.20.1.5 |
ipRouteTableThis entity's IP Routing table. SEQUENCE OF IpRouteEntry .1.3.6.1.4.1.3727.20.20.3.1.4.21 |
ipRouteEntryA route to a particular destination. IpRouteEntry .1.3.6.1.4.1.3727.20.20.3.1.4.21.1 |
ipRouteDestThe destination IP address of this route. An
entry with a value of 0.0.0.0 is considered a
default route. Multiple routes to a single
destination can appear in the table, but access to
such multiple entries is dependent on the table-
access mechanisms defined by the network
management protocol in use.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.1 |
ipRouteIfIndexThe index value which uniquely identifies the
local interface through which the next hop of this
route should be reached. The interface identified
by a particular value of this index is the same
interface as identified by the same value of
ifIndex.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.2 |
ipRouteMetric1The primary routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
ipRouteProto value. If this metric is not used,
its value should be set to -1.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.3 |
ipRouteMetric2An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
ipRouteProto value. If this metric is not used,
its value should be set to -1.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.4 |
ipRouteMetric3An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
ipRouteProto value. If this metric is not used,
its value should be set to -1.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.5 |
ipRouteMetric4An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
ipRouteProto value. If this metric is not used,
its value should be set to -1.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.6 |
ipRouteNextHopThe IP address of the next hop of this route.
(In the case of a route bound to an interface
which is realized via a broadcast media, the value
of this field is the agent's IP address on that
interface.)ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.7 |
ipRouteTypeThe type of route. Note that the values
direct(3) and indirect(4) refer to the notion of
direct and indirect routing in the IP
architecture.
Setting this object to the value invalid(2) has
the effect of invalidating the corresponding entry
in the ipRouteTable object. That is, it
effectively dissasociates the destination
identified with said entry from the route
identified with said entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.
Accordingly, management stations must be prepared
to receive tabular information from agents that
corresponds to entries not currently in use.
Proper interpretation of such entries requires
examination of the relevant ipRouteType object.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.8 |
ipRouteProtoThe routing mechanism via which this route was
learned. Inclusion of values for gateway routing
protocols is not intended to imply that hosts
should support those protocols.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.9 |
ipRouteAgeThe number of seconds since this route was last
updated or otherwise determined to be correct.
Note that no semantics of `too old' can be implied
except through knowledge of the routing protocol
by which the route was learned.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.10 |
ipRouteMaskIndicate the mask to be logical-ANDed with the
destination address before being compared to the
value in the ipRouteDest field. For those systems
that do not support arbitrary subnet masks, an
agent constructs the value of the ipRouteMask by
determining whether the value of the correspondent
ipRouteDest field belong to a class-A, B, or C
network, and then using one of:
mask network
255.0.0.0 class-A
255.255.0.0 class-B
255.255.255.0 class-C
If the value of the ipRouteDest is 0.0.0.0 (a
default route), then the mask value is also
0.0.0.0. It should be noted that all IP routing
subsystems implicitly use this mechanism.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.11 |
ipRouteMetric5An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
ipRouteProto value. If this metric is not used,
its value should be set to -1.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.12 |
ipRouteInfoA reference to MIB definitions specific to the
particular routing protocol which is responsible
for this route, as determined by the value
specified in the route's ipRouteProto value. If
this information is not present, its value should
be set to the OBJECT IDENTIFIER { 0 0 }, which is
a syntatically valid object identifier, and any
conformant implementation of ASN.1 and BER must be
able to generate and recognize this value.ro OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.4.21.1.13 |
ipNetToMediaTableThe IP Address Translation table used for mapping
from IP addresses to physical addresses. SEQUENCE OF IpNetToMediaEntry .1.3.6.1.4.1.3727.20.20.3.1.4.22 |
ipNetToMediaEntryEach entry contains one IpAddress to `physical'
address equivalence. IpNetToMediaEntry .1.3.6.1.4.1.3727.20.20.3.1.4.22.1 |
ipNetToMediaIfIndexThe interface on which this entry's equivalence
is effective. The interface identified by a
particular value of this index is the same
interface as identified by the same value of
ifIndex.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.22.1.1 |
ipNetToMediaPhysAddressThe media-dependent `physical' address.ro OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.4.22.1.2 |
ipNetToMediaNetAddressThe IpAddress corresponding to the media-
dependent `physical' address.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.4.22.1.3 |
ipNetToMediaTypeThe type of mapping.
Setting this object to the value invalid(2) has
the effect of invalidating the corresponding entry
in the ipNetToMediaTable. That is, it effectively
dissasociates the interface identified with said
entry from the mapping identified with said entry.
It is an implementation-specific matter as to
whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive tabular information
from agents that corresponds to entries not
currently in use. Proper interpretation of such
entries requires examination of the relevant
ipNetToMediaType object.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.4.22.1.4 |
ipRoutingDiscardsThe number of routing entries which were chosen
to be discarded even though they are valid. One
possible reason for discarding such an entry could
be to free-up buffer space for other routing
entries.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.4.23 |
icmp OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.5 |
icmpInMsgsThe total number of ICMP messages which the
entity received. Note that this counter includes
all those counted by icmpInErrors.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.1 |
icmpInErrorsThe number of ICMP messages which the entity
received but determined as having ICMP-specific
errors (bad ICMP checksums, bad length, etc.).ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.2 |
icmpInDestUnreachsThe number of ICMP Destination Unreachable
messages received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.3 |
icmpInTimeExcdsThe number of ICMP Time Exceeded messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.4 |
icmpInParmProbsThe number of ICMP Parameter Problem messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.5 |
icmpInSrcQuenchsThe number of ICMP Source Quench messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.6 |
icmpInRedirectsThe number of ICMP Redirect messages received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.7 |
icmpInEchosThe number of ICMP Echo (request) messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.8 |
icmpInEchoRepsThe number of ICMP Echo Reply messages received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.9 |
icmpInTimestampsThe number of ICMP Timestamp (request) messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.10 |
icmpInTimestampRepsThe number of ICMP Timestamp Reply messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.11 |
icmpInAddrMasksThe number of ICMP Address Mask Request messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.12 |
icmpInAddrMaskRepsThe number of ICMP Address Mask Reply messages
received.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.13 |
icmpOutMsgsThe total number of ICMP messages which this
entity attempted to send. Note that this counter
includes all those counted by icmpOutErrors.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.14 |
icmpOutErrorsThe number of ICMP messages which this entity did
not send due to problems discovered within ICMP
such as a lack of buffers. This value should not
include errors discovered outside the ICMP layer
such as the inability of IP to route the resultant
datagram. In some implementations there may be no
types of error which contribute to this counter's
value.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.15 |
icmpOutDestUnreachsThe number of ICMP Destination Unreachable
messages sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.16 |
icmpOutTimeExcdsThe number of ICMP Time Exceeded messages sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.17 |
icmpOutParmProbsThe number of ICMP Parameter Problem messages
sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.18 |
icmpOutSrcQuenchsThe number of ICMP Source Quench messages sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.19 |
icmpOutRedirectsThe number of ICMP Redirect messages sent. For a
host, this object will always be zero, since hosts
do not send redirects.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.20 |
icmpOutEchosThe number of ICMP Echo (request) messages sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.21 |
icmpOutEchoRepsThe number of ICMP Echo Reply messages sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.22 |
icmpOutTimestampsThe number of ICMP Timestamp (request) messages
sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.23 |
icmpOutTimestampRepsThe number of ICMP Timestamp Reply messages
sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.24 |
icmpOutAddrMasksThe number of ICMP Address Mask Request messages
sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.25 |
icmpOutAddrMaskRepsThe number of ICMP Address Mask Reply messages
sent.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.5.26 |
tcp OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.6 |
tcpRtoAlgorithmThe algorithm used to determine the timeout value
used for retransmitting unacknowledged octets.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.6.1 |
tcpRtoMinThe minimum value permitted by a TCP
implementation for the retransmission timeout,
measured in milliseconds. More refined semantics
for objects of this type depend upon the algorithm
used to determine the retransmission timeout. In
particular, when the timeout algorithm is rsre(3),
an object of this type has the semantics of the
LBOUND quantity described in RFC 793.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.6.2 |
tcpRtoMaxThe maximum value permitted by a TCP
implementation for the retransmission timeout,
measured in milliseconds. More refined semantics
for objects of this type depend upon the algorithm
used to determine the retransmission timeout. In
particular, when the timeout algorithm is rsre(3),
an object of this type has the semantics of the
UBOUND quantity described in RFC 793.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.6.3 |
tcpMaxConnThe limit on the total number of TCP connections
the entity can support. In entities where the
maximum number of connections is dynamic, this
object should contain the value -1.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.6.4 |
tcpActiveOpensThe number of times TCP connections have made a
direct transition to the SYN-SENT state from the
CLOSED state.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.5 |
tcpPassiveOpensThe number of times TCP connections have made a
direct transition to the SYN-RCVD state from the
LISTEN state.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.6 |
tcpAttemptFailsThe number of times TCP connections have made a
direct transition to the CLOSED state from either
the SYN-SENT state or the SYN-RCVD state, plus the
number of times TCP connections have made a direct
transition to the LISTEN state from the SYN-RCVD
state.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.7 |
tcpEstabResetsThe number of times TCP connections have made a
direct transition to the CLOSED state from either
the ESTABLISHED state or the CLOSE-WAIT state.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.8 |
tcpCurrEstabThe number of TCP connections for which the
current state is either ESTABLISHED or CLOSE-
WAIT.ro Gauge .1.3.6.1.4.1.3727.20.20.3.1.6.9 |
tcpInSegsThe total number of segments received, including
those received in error. This count includes
segments received on currently established
connections.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.10 |
tcpOutSegsThe total number of segments sent, including
those on current connections but excluding those
containing only retransmitted octets.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.11 |
tcpRetransSegsThe total number of segments retransmitted - that
is, the number of TCP segments transmitted
containing one or more previously transmitted
octets.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.12 |
tcpConnTableA table containing TCP connection-specific
information. SEQUENCE OF TcpConnEntry .1.3.6.1.4.1.3727.20.20.3.1.6.13 |
tcpConnEntryInformation about a particular current TCP
connection. An object of this type is transient,
in that it ceases to exist when (or soon after)
the connection makes the transition to the CLOSED
state. TcpConnEntry .1.3.6.1.4.1.3727.20.20.3.1.6.13.1 |
tcpConnStateThe state of this TCP connection.
The only value which may be set by a management
station is deleteTCB(12). Accordingly, it is
appropriate for an agent to return a `badValue'
response if a management station attempts to set
this object to any other value.
If a management station sets this object to the
value deleteTCB(12), then this has the effect of
deleting the TCB (as defined in RFC 793) of the
corresponding connection on the managed node,
resulting in immediate termination of the
connection.
As an implementation-specific option, a RST
segment may be sent from the managed node to the
other TCP endpoint (note however that RST segments
are not sent reliably).ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.6.13.1.1 |
tcpConnLocalAddressThe local IP address for this TCP connection. In
the case of a connection in the listen state which
is willing to accept connections for any IP
interface associated with the node, the value
0.0.0.0 is used.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.6.13.1.2 |
tcpConnLocalPortThe local port number for this TCP connection.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.6.13.1.3 |
tcpConnRemAddressThe remote IP address for this TCP connection.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.6.13.1.4 |
tcpConnRemPortThe remote port number for this TCP connection.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.6.13.1.5 |
tcpInErrsThe total number of segments received in error
(e.g., bad TCP checksums).ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.14 |
tcpOutRstsThe number of TCP segments sent containing the
RST flag.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.6.15 |
udp OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.7 |
udpInDatagramsThe total number of UDP datagrams delivered to
UDP users.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.7.1 |
udpNoPortsThe total number of received UDP datagrams for
which there was no application at the destination
port.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.7.2 |
udpInErrorsThe number of received UDP datagrams that could
not be delivered for reasons other than the lack
of an application at the destination port.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.7.3 |
udpOutDatagramsThe total number of UDP datagrams sent from this
entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.7.4 |
udpTableA table containing UDP listener information. SEQUENCE OF UdpEntry .1.3.6.1.4.1.3727.20.20.3.1.7.5 |
udpEntryInformation about a particular current UDP
listener. UdpEntry .1.3.6.1.4.1.3727.20.20.3.1.7.5.1 |
udpLocalAddressThe local IP address for this UDP listener. In
the case of a UDP listener which is willing to
accept datagrams for any IP interface associated
with the node, the value 0.0.0.0 is used.ro IpAddress .1.3.6.1.4.1.3727.20.20.3.1.7.5.1.1 |
udpLocalPortThe local port number for this UDP listener.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.7.5.1.2 |
snmp OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.11 |
snmpInPktsThe total number of Messages delivered to the
SNMP entity from the transport service.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.1 |
snmpOutPktsThe total number of SNMP Messages which were
passed from the SNMP protocol entity to the
transport service.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.2 |
snmpInBadVersionsThe total number of SNMP Messages which were
delivered to the SNMP protocol entity and were for
an unsupported SNMP version.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.3 |
snmpInBadCommunityNamesThe total number of SNMP Messages delivered to
the SNMP protocol entity which used a SNMP
community name not known to said entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.4 |
snmpInBadCommunityUsesThe total number of SNMP Messages delivered to
the SNMP protocol entity which represented an SNMP
operation which was not allowed by the SNMP
community named in the Message.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.5 |
snmpInASNParseErrsThe total number of ASN.1 or BER errors
encountered by the SNMP protocol entity when
decoding received SNMP Messages.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.6 |
snmpInTooBigsThe total number of SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field is
`tooBig'.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.8 |
snmpInNoSuchNamesThe total number of SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field is
`noSuchName'.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.9 |
snmpInBadValuesThe total number of SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field is
`badValue'.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.10 |
snmpInReadOnlysThe total number valid SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field is
`readOnly'. It should be noted that it is a
protocol error to generate an SNMP PDU which
contains the value `readOnly' in the error-status
field, as such this object is provided as a means
of detecting incorrect implementations of the
SNMP.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.11 |
snmpInGenErrsThe total number of SNMP PDUs which were
delivered to the SNMP protocol entity and for
which the value of the error-status field is
`genErr'.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.12 |
snmpInTotalReqVarsThe total number of MIB objects which have been
retrieved successfully by the SNMP protocol entity
as the result of receiving valid SNMP Get-Request
and Get-Next PDUs.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.13 |
snmpInTotalSetVarsThe total number of MIB objects which have been
altered successfully by the SNMP protocol entity
as the result of receiving valid SNMP Set-Request
PDUs.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.14 |
snmpInGetRequestsThe total number of SNMP Get-Request PDUs which
have been accepted and processed by the SNMP
protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.15 |
snmpInGetNextsThe total number of SNMP Get-Next PDUs which have
been accepted and processed by the SNMP protocol
entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.16 |
snmpInSetRequestsThe total number of SNMP Set-Request PDUs which
have been accepted and processed by the SNMP
protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.17 |
snmpInGetResponsesThe total number of SNMP Get-Response PDUs which
have been accepted and processed by the SNMP
protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.18 |
snmpInTrapsThe total number of SNMP Trap PDUs which have
been accepted and processed by the SNMP protocol
entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.19 |
snmpOutTooBigsThe total number of SNMP PDUs which were
generated by the SNMP protocol entity and for
which the value of the error-status field is
`tooBig.'ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.20 |
snmpOutNoSuchNamesThe total number of SNMP PDUs which were
generated by the SNMP protocol entity and for
which the value of the error-status is
`noSuchName'.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.21 |
snmpOutBadValuesThe total number of SNMP PDUs which were
generated by the SNMP protocol entity and for
which the value of the error-status field is
`badValue'.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.22 |
snmpOutGenErrsThe total number of SNMP PDUs which were
generated by the SNMP protocol entity and for
which the value of the error-status field is
`genErr'.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.24 |
snmpOutGetRequestsThe total number of SNMP Get-Request PDUs which
have been generated by the SNMP protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.25 |
snmpOutGetNextsThe total number of SNMP Get-Next PDUs which have
been generated by the SNMP protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.26 |
snmpOutSetRequestsThe total number of SNMP Set-Request PDUs which
have been generated by the SNMP protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.27 |
snmpOutGetResponsesThe total number of SNMP Get-Response PDUs which
have been generated by the SNMP protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.28 |
snmpOutTrapsThe total number of SNMP Trap PDUs which have
been generated by the SNMP protocol entity.ro Counter .1.3.6.1.4.1.3727.20.20.3.1.11.29 |
snmpEnableAuthenTrapsIndicates whether the SNMP agent process is
permitted to generate authentication-failure
traps. The value of this object overrides any
configuration information; as such, it provides a
means whereby all authentication-failure traps may
be disabled.
Note that it is strongly recommended that this
object be stored in non-volatile memory so that it
remains constant between re-initializations of the
network management system.
For JetDirect, this object is only implemented for
agents which include a tcpip stack. This is generally
the case, but with the advent of NOVELL only products
this object will not be available.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.11.30 |
appletalk OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.13 |
atport OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.13.3 |
atportTableA list of AppleTalk ports for this entity. SEQUENCE OF AtportEntry .1.3.6.1.4.1.3727.20.20.3.1.13.3.1 |
atportEntryThe description of one of the AppleTalk
ports on this entity. AtportEntry .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1 |
atportIndexA unique value for each AppleTalk port.
Its value is between 1 and the total number of
AppleTalk ports. The value for each port must
remain constant at least from the
re-initialization of the entity's network
management system to the next
re-initialization.ro INTEGER .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.1 |
atportDescrA text string containing information about the
port. This string is intended for presentation
to a human; it must not contain anything but
printable ASCII characters.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.2 |
atportTypeThe type of port, distinguished by the protocol
immediately below DDP in the protocol stack.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.3 |
atportNetStartThe first AppleTalk network address in the range
configured for this port. This is a two octet
DDP network address in network byte order.rw OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.4 |
atportNetEndThe last AppleTalk network address in the range
configured for this port. This is a two octet
DDP network address in network byte order. If the
network to which this AppleTalk port is
connected is a Phase 1 network or a non-extended
network, the value for atportNetEnd shall be two
octets of zero.rw OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.5 |
atportNetAddressThe AppleTalk network address configured for this
port.rw DdpAddress .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.6 |
atportStatusThe configuration status of this port.
Setting this object to the value invalid(4)
has the effect of invalidating the corresponding
entry in the atportTable. That is, it
effectively disassociates the mapping identified
with said entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.
Accordingly, management stations must be
prepared to receive from agents tabular
information corresponding to entries not
currently in use. Proper interpretation of such
entries requires examination of the relevant
atportStatus object.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.7 |
atportNetConfigThe configuration status of this port.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.8 |
atportZoneConfigThe configuration status of the zone information
for this port.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.9 |
atportZoneThe zone name configured for this AppleTalk port.rw OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.10 |
atportIfIndexThe physical interface associated with this
AppleTalk port. The interface identified by a
particular value of this index is the same
interface as identified by the same value of
ifIndex.rw INTEGER .1.3.6.1.4.1.3727.20.20.3.1.13.3.1.1.11 |