OSPFV3-MIB
AI MIB Summary
The OSPFV3-MIB provides SNMP-based monitoring and management of OSPFv3 routing processes, exposing key metrics such as neighbor adjacency states, interface link-local addresses, LSDB synchronization status, and SPF calculation statistics for IPv6 networks.
The MIB module for OSPF version 3.
Copyright (c) 2009 IETF Trust and the persons identified as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
- Redistributions of source code must retain the above
copyright notice, this list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
- Neither the name of Internet Society, IETF or IETF
Trust, nor the names of specific contributors, may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This version of this MIB module is part of RFC 5643; see the RFC itself for full legal notices.
Main OID:
ospfv3MIB.1.3.6.1.4.1.3727.20.20.3.1.191
214
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
214 total| Object Name |
|---|
ospfv3MIBThe MIB module for OSPF version 3.
Copyright (c) 2009 IETF Trust and the persons
identified as authors of the code. All rights
reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that
the following conditions are met:
- Redistributions of source code must retain the above
copyright notice, this list of conditions and the
following disclaimer.
- Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or
other materials provided with the distribution.
- Neither the name of Internet Society, IETF or IETF
Trust, nor the names of specific contributors, may be
used to endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
This version of this MIB module is part of RFC 5643;
see the RFC itself for full legal notices. MODULE-IDENTITY .1.3.6.1.4.1.3727.20.20.3.1.191 |
ospfv3Notifications OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.191.0 |
ospfv3VirtIfStateChangeAn ospfv3VirtIfStateChange notification signifies that
there has been a change in the state of an OSPFv3 virtual
interface.
This notification should be generated when the interface
state regresses (e.g., goes from Point-to-Point to Down)
or progresses to a terminal state (i.e., Point-to-Point). NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.1 |
ospfv3NbrStateChangeAn ospfv3NbrStateChange notification signifies that
there has been a change in the state of a
non-virtual OSPFv3 neighbor. This notification should be
generated when the neighbor state regresses
(e.g., goes from Attempt or Full to 1-Way or
Down) or progresses to a terminal state (e.g.,
2-Way or Full). When a neighbor transitions
from or to Full on non-broadcast multi-access
and broadcast networks, the notification should be
generated by the Designated Router. A Designated
Router transitioning to Down will be noted by
ospfIfStateChange. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.2 |
ospfv3VirtNbrStateChangeAn ospfv3VirtNbrStateChange notification signifies
that there has been a change in the state of an OSPFv3
virtual neighbor. This notification should be generated
when the neighbor state regresses (e.g., goes
from Attempt or Full to 1-Way or Down) or
progresses to a terminal state (e.g., Full). NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.3 |
ospfv3IfConfigErrorAn ospfv3IfConfigError notification signifies that a
packet has been received on a non-virtual
interface from a router whose configuration
parameters conflict with this router's
configuration parameters. Note that the event
optionMismatch should cause a notification only if it
prevents an adjacency from forming. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.4 |
ospfv3VirtIfConfigErrorAn ospfv3VirtIfConfigError notification signifies that a
packet has been received on a virtual interface
from a router whose configuration parameters
conflict with this router's configuration
parameters. Note that the event optionMismatch
should cause a notification only if it prevents an
adjacency from forming. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.5 |
ospfv3IfRxBadPacketAn ospfv3IfRxBadPacket notification signifies that an
OSPFv3 packet that cannot be parsed has been received on a
non-virtual interface. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.6 |
ospfv3VirtIfRxBadPacketAn ospfv3VirtIfRxBadPacket notification signifies
that an OSPFv3 packet that cannot be parsed has been
received on a virtual interface. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.7 |
ospfv3LsdbOverflowAn ospfv3LsdbOverflow notification signifies that the
number of LSAs in the router's link state
database has exceeded ospfv3ExtAreaLsdbLimit. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.8 |
ospfv3LsdbApproachingOverflowAn ospfv3LsdbApproachingOverflow notification signifies
that the number of LSAs in the router's
link state database has exceeded ninety percent of
ospfv3ExtAreaLsdbLimit. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.9 |
ospfv3IfStateChangeAn ospfv3IfStateChange notification signifies that there
has been a change in the state of a non-virtual
OSPFv3 interface. This notification should be generated
when the interface state regresses (e.g., goes
from DR to Down) or progresses to a terminal
state (i.e., Point-to-Point, DR Other, DR, or
Backup). NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.10 |
ospfv3NssaTranslatorStatusChangeAn ospfv3NssaTranslatorStatusChange notification
indicates that there has been a change in the router's
ability to translate OSPFv3 NSSA LSAs into OSPFv3 External
LSAs. This notification should be generated when the
Translator Status transitions from or to any defined
status on a per-area basis. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.11 |
ospfv3RestartStatusChangeAn ospfv3RestartStatusChange notification signifies that
there has been a change in the graceful restart
state for the router. This notification should be
generated when the router restart status
changes. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.12 |
ospfv3NbrRestartHelperStatusChangeAn ospfv3NbrRestartHelperStatusChange notification
signifies that there has been a change in the
graceful restart helper state for the neighbor.
This notification should be generated when the
neighbor restart helper status transitions for a neighbor. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.13 |
ospfv3VirtNbrRestartHelperStatusChangeAn ospfv3VirtNbrRestartHelperStatusChange
notification signifies that there has been a
change in the graceful restart helper state for
the virtual neighbor. This notification should be
generated when the virtual neighbor restart helper status
transitions for a virtual neighbor. NOTIFICATION-TYPE .1.3.6.1.4.1.3727.20.20.3.1.191.0.14 |
ospfv3Objects OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.191.1 |
ospfv3GeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.191.1.1 |
ospfv3RouterIdA 32-bit unsigned integer uniquely identifying
the router in the Autonomous System. To ensure
uniqueness, this may default to the 32-bit
unsigned integer representation of one of
the router's IPv4 interface addresses (if IPv4
is configured on the router).
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.1 |
ospfv3AdminStatusThe administrative status of OSPFv3 in the
router. The value 'enabled' denotes that the
OSPFv3 Process is active on at least one
interface; 'disabled' disables it on all
interfaces.
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw Status (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.2 |
ospfv3VersionNumberThe version number of OSPF for IPv6 is 3.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.3 |
ospfv3AreaBdrRtrStatusA flag to denote whether this router is an area
border router. The value of this object is true (1)
when the router is an area border router.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.4 |
ospfv3ASBdrRtrStatusA flag to note whether this router is
configured as an Autonomous System border router.
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.5 |
ospfv3AsScopeLsaCountThe number of AS-scope (e.g., AS-External) link state
advertisements in the link state database.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.6 |
ospfv3AsScopeLsaCksumSumThe 32-bit unsigned sum of the LS checksums of
the AS-scoped link state advertisements
contained in the link state database. This sum
can be used to determine if there has been a
change in a router's link state database or
to compare the link state database of two
routers.ro Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.7 |
ospfv3OriginateNewLsasThe number of new link state advertisements
that have been originated. This number is
incremented each time the router originates a new
LSA.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.8 |
ospfv3RxNewLsasThe number of link state advertisements
received that are determined to be new
instantiations. This number does not include
newer instantiations of self-originated link state
advertisements.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.9 |
ospfv3ExtLsaCountThe number of External (LS type 0x4005) in the
link state database.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.10 |
ospfv3ExtAreaLsdbLimitThe maximum number of non-default
AS-external-LSA entries that can be stored in the
link state database. If the value is -1, then
there is no limit.
When the number of non-default AS-external-LSAs
in a router's link state database reaches
ospfv3ExtAreaLsdbLimit, the router enters Overflow
state. The router never holds more than
ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs
in its database. ospfv3ExtAreaLsdbLimit MUST be set
identically in all routers attached to the OSPFv3
backbone and/or any regular OSPFv3 area (i.e.,
OSPFv3 stub areas and not-so-stubby-areas (NSSAs)
are excluded).
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw Integer32 (-1..'7FFFFFFF'h) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.11 |
ospfv3ExitOverflowIntervalThe number of seconds that, after entering
Overflow state, a router will attempt to leave
Overflow state. This allows the router to again
originate non-default, AS-External-LSAs. When
set to 0, the router will not leave Overflow
state until restarted.
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.12 |
ospfv3DemandExtensionsThe router's support for demand circuits.
The value of this object is true (1) when
demand circuits are supported.
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.13 |
ospfv3ReferenceBandwidthReference bandwidth in kilobits per second for
calculating default interface metrics. The
default value is 100,000 KBPS (100 MBPS).
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.14 |
ospfv3RestartSupportThe router's support for OSPF graceful restart.
Options include no restart support, only planned
restarts, or both planned and unplanned restarts.
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.15 |
ospfv3RestartIntervalConfigured OSPF graceful restart timeout interval.
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.16 |
ospfv3RestartStrictLsaCheckingIndicates if strict LSA checking is enabled for
graceful restart. A value of true (1) indicates that
strict LSA checking is enabled.
This object is persistent, and when written,
the entity SHOULD save the change to non-volatile
storage.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.17 |
ospfv3RestartStatusThe current status of OSPF graceful restart capability.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.18 |
ospfv3RestartAgeRemaining time in the current OSPF graceful restart
interval.ro Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.19 |
ospfv3RestartExitReasonDescribes the outcome of the last attempt at a
graceful restart.
none: no restart has yet been attempted.
inProgress: a restart attempt is currently underway.
completed: the last restart completed successfully.
timedOut: the last restart timed out.
topologyChanged: the last restart was aborted due to
a topology change.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.20 |
ospfv3NotificationEnableThis object provides a coarse level of control
over the generation of OSPFv3 notifications.
If this object is set to true (1), then it enables
the generation of OSPFv3 notifications. If it is
set to false (2), these notifications are not
generated.
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.21 |
ospfv3StubRouterSupportThe router's support for stub router functionality. An
object value of true (1) indicates that stub router
functionality is supported.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.22 |
ospfv3StubRouterAdvertisementThis object controls the advertisement of
stub LSAs by the router. The value
doNotAdvertise (1) will result in the advertisement
of standard LSAs and is the default value.
This object is persistent, and when written,
the entity SHOULD save the change to non-volatile
storage.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.23 |
ospfv3DiscontinuityTimeThe value of sysUpTime on the most recent occasion
at which any one of this MIB's counters suffered
a discontinuity.
If no such discontinuities have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.24 |
ospfv3RestartTimeThe value of sysUpTime on the most recent occasion
at which the ospfv3RestartExitReason was updated.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.1.25 |
ospfv3AreaTableInformation describing the configured
parameters and cumulative statistics of the router's
attached areas. The interfaces and
virtual links are configured as part of these areas.
Area 0, by definition, is the backbone area. SEQUENCE OF Ospfv3AreaEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.2 |
ospfv3AreaEntryInformation describing the configured
parameters and cumulative statistics of one of the
router's attached areas.
The information in this table is persistent,
and when written, the entity SHOULD save the a
change to non-volatile storage. Ospfv3AreaEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1 |
ospfv3AreaIdA 32-bit unsigned integer uniquely identifying an area.
Area ID 0 is used for the OSPFv3 backbone. Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.1 |
ospfv3AreaImportAsExternIndicates whether an area is a stub area, NSSA, or
standard area. AS-scope LSAs are not imported into stub
areas or NSSAs. NSSAs import AS-External data as NSSA
LSAs that have Area-scope.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.2 |
ospfv3AreaSpfRunsThe number of times that the intra-area route
table has been calculated using this area's
link state database. This is typically done
using Dijkstra's algorithm.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.3 |
ospfv3AreaBdrRtrCountThe total number of area border routers
reachable within this area. This is initially zero,
and is calculated in each Shortest Path First (SPF)
pass.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.4 |
ospfv3AreaAsBdrRtrCountThe total number of Autonomous System border
routers reachable within this area. This is
initially zero, and is calculated in each SPF
pass.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.5 |
ospfv3AreaScopeLsaCountThe total number of Area-scope link state
advertisements in this area's link state
database.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.6 |
ospfv3AreaScopeLsaCksumSumThe 32-bit unsigned sum of the Area-scope link state
advertisements' LS checksums contained in this
area's link state database. The sum can be used
to determine if there has been a change in a
router's link state database or to compare the
link state database of two routers.ro Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.7 |
ospfv3AreaSummaryThe variable ospfv3AreaSummary controls the
import of Inter-Area LSAs into stub and
NSSA areas. It has no effect on other areas.
If it is noAreaSummary, the router will neither
originate nor propagate Inter-Area LSAs into the
stub or NSSA area. It will only advertise a
default route.
If it is sendAreaSummary, the router will both
summarize and propagate Inter-Area LSAs.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.8 |
ospfv3AreaRowStatusThis object permits management of the table by
facilitating actions such as row creation,
construction, and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.9 |
ospfv3AreaStubMetricThe metric value advertised for the default route
into stub and NSSA areas. By default, this equals the
least metric among the interfaces to other areas.rw BigMetric (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.10 |
ospfv3AreaNssaTranslatorRoleIndicates an NSSA border router's policy to
perform NSSA translation of NSSA-LSAs into
AS-External-LSAs.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.11 |
ospfv3AreaNssaTranslatorStateIndicates if and how an NSSA border router is
performing NSSA translation of NSSA-LSAs into
AS-External-LSAs. When this object is set to
'enabled', the NSSA border router's
ospfv3AreaNssaTranslatorRole has been set to 'always'.
When this object is set to 'elected', a candidate
NSSA border router is translating NSSA-LSAs into
AS-External-LSAs. When this object is set to
'disabled', a candidate NSSA Border router is NOT
translating NSSA-LSAs into AS-External-LSAs.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.12 |
ospfv3AreaNssaTranslatorStabIntervalThe stability interval defined as the number of
seconds after an elected translator determines its
services are no longer required that it should
continue to perform its translation duties.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.13 |
ospfv3AreaNssaTranslatorEventsIndicates the number of Translator state changes
that have occurred since the last start-up of the
OSPFv3 routing process.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.14 |
ospfv3AreaStubMetricTypeThis variable assigns the type of metric
advertised as a default route.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.15 |
ospfv3AreaTEEnabledIndicates whether or not traffic engineering
is enabled in the area. The object is set
to the value true (1) to enable traffic engineering.
Traffic engineering is disabled by default.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.2.1.16 |
ospfv3AsLsdbTableThe OSPFv3 Process's AS-scope link state database
(LSDB). The LSDB contains the AS-scope link state
advertisements from throughout the areas that the
device is attached to. SEQUENCE OF Ospfv3AsLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.3 |
ospfv3AsLsdbEntryA single AS-scope link state advertisement. Ospfv3AsLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1 |
ospfv3AsLsdbTypeThe type of the link state advertisement.
Each link state type has a separate
advertisement format. AS-scope LSAs not recognized
by the router may be stored in the database. Unsigned32(0..'FFFFFFFF'h) .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.1 |
ospfv3AsLsdbRouterIdThe 32-bit number that uniquely identifies the
originating router in the Autonomous System. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.2 |
ospfv3AsLsdbLsidThe Link State ID is an LS type-specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics. Ospfv3LsIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.3 |
ospfv3AsLsdbSequenceThe sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number, the more recent the
advertisement.ro Ospfv3LsaSequenceTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.4 |
ospfv3AsLsdbAgeThis field is the age of the link state
advertisement in seconds. The high-order bit
of the LS age field is considered the DoNotAge
bit for support of on-demand circuits.ro Ospfv3LsaAgeTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.5 |
ospfv3AsLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.6 |
ospfv3AsLsdbAdvertisementThe entire link state advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.7 |
ospfv3AsLsdbTypeKnownThe value true (1) indicates that the LSA type
is recognized by this router.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.3.1.8 |
ospfv3AreaLsdbTableThe OSPFv3 Process's Area-scope LSDB.
The LSDB contains the Area-scope link state
advertisements from throughout the area that the
device is attached to. SEQUENCE OF Ospfv3AreaLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.4 |
ospfv3AreaLsdbEntryA single Area-scope link state advertisement. Ospfv3AreaLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1 |
ospfv3AreaLsdbAreaIdThe 32-bit identifier of the Area from which the
LSA was received. Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.1 |
ospfv3AreaLsdbTypeThe type of the link state advertisement.
Each link state type has a separate
advertisement format. Area-scope LSAs unrecognized
by the router are also stored in this database. Unsigned32(0..'FFFFFFFF'h) .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.2 |
ospfv3AreaLsdbRouterIdThe 32-bit number that uniquely identifies the
originating router in the Autonomous System. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.3 |
ospfv3AreaLsdbLsidThe Link State ID is an LS type-specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics. Ospfv3LsIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.4 |
ospfv3AreaLsdbSequenceThe sequence number field is a signed 32-bit
integer. It is used to detect old and
duplicate link state advertisements. The space
of sequence numbers is linearly ordered. The
larger the sequence number, the more recent the
advertisement.ro Ospfv3LsaSequenceTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.5 |
ospfv3AreaLsdbAgeThis field is the age of the link state
advertisement in seconds. The high-order bit
of the LS age field is considered the DoNotAge
bit for support of on-demand circuits.ro Ospfv3LsaAgeTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.6 |
ospfv3AreaLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.7 |
ospfv3AreaLsdbAdvertisementThe entire link state advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.8 |
ospfv3AreaLsdbTypeKnownThe value true (1) indicates that the LSA type is
recognized by this router.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.4.1.9 |
ospfv3LinkLsdbTableThe OSPFv3 Process's Link-scope LSDB for non-virtual
interfaces. The LSDB contains the Link-scope link
state advertisements from the interfaces that the
device is attached to. SEQUENCE OF Ospfv3LinkLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.5 |
ospfv3LinkLsdbEntryA single Link-scope link state advertisement. Ospfv3LinkLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1 |
ospfv3LinkLsdbIfIndexThe identifier of the link from which the LSA
was received. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.1 |
ospfv3LinkLsdbIfInstIdThe identifier of the interface instance from
which the LSA was received. Ospfv3IfInstIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.2 |
ospfv3LinkLsdbTypeThe type of the link state advertisement.
Each link state type has a separate
advertisement format. Link-scope LSAs unrecognized
by the router are also stored in this database. Unsigned32(0..'FFFFFFFF'h) .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.3 |
ospfv3LinkLsdbRouterIdThe 32-bit number that uniquely identifies the
originating router in the Autonomous System. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.4 |
ospfv3LinkLsdbLsidThe Link State ID is an LS type-specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics. However, in OSPFv3
the Link State ID always contains the flooding
scope of the LSA. Ospfv3LsIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.5 |
ospfv3LinkLsdbSequenceThe sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number, the more recent the
advertisement.ro Ospfv3LsaSequenceTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.6 |
ospfv3LinkLsdbAgeThis field is the age of the link state
advertisement in seconds. The high-order bit
of the LS age field is considered the DoNotAge
bit for support of on-demand circuits.ro Ospfv3LsaAgeTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.7 |
ospfv3LinkLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.8 |
ospfv3LinkLsdbAdvertisementThe entire link state advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.9 |
ospfv3LinkLsdbTypeKnownThe value true (1) indicates that the LSA type is
recognized by this router.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.5.1.10 |
ospfv3HostTableThe Host/Metric Table indicates what hosts are
directly attached to the router and their
corresponding metrics. SEQUENCE OF Ospfv3HostEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.6 |
ospfv3HostEntryA metric to be advertised when a given host is
reachable.
The information in this table is persistent, and
when written, the entity SHOULD save the change
to non-volatile storage. Ospfv3HostEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.6.1 |
ospfv3HostAddressTypeThe address type of ospfv3HostAddress. Only IPv6
global address type is expected. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.6.1.1 |
ospfv3HostAddressThe IPv6 address of the host. Must be an
IPv6 global address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.6.1.2 |
ospfv3HostMetricThe metric to be advertised.rw Metric (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.6.1.3 |
ospfv3HostRowStatusThis object permits management of the table by
facilitating actions such as row creation,
construction, and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.6.1.4 |
ospfv3HostAreaIDThe Area the host entry is to be found within.
By default, the area for the subsuming OSPFv3
interface, or Area 0 if there is no subsuming
interface.rw Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.6.1.5 |
ospfv3IfTableThe OSPFv3 Interface Table describes the
interfaces from the viewpoint of OSPFv3. SEQUENCE OF Ospfv3IfEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.7 |
ospfv3IfEntryThe OSPFv3 Interface Entry describes one
interface from the viewpoint of OSPFv3.
The information in this table is persistent,
and when written, the entity SHOULD save the
change to non-volatile storage. Ospfv3IfEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1 |
ospfv3IfIndexThe interface index of this OSPFv3 interface.
It corresponds to the interface index of the
IPv6 interface on which OSPFv3 is configured. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.1 |
ospfv3IfInstIdEnables multiple interface instances of OSPFv3
to be run over a single link. Each interface
instance would be assigned a separate ID. This ID
has local link significance only. Ospfv3IfInstIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.2 |
ospfv3IfAreaIdA 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0 is used for the OSPFv3 backbone.rw Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.3 |
ospfv3IfTypeThe OSPFv3 interface type.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.4 |
ospfv3IfAdminStatusThe OSPFv3 interface's administrative status.
The value formed on the interface; the interface
will be advertised as an internal route to some
area. The value 'disabled' denotes that the
interface is external to OSPFv3.
Note that a value of 'disabled' for the object
ospfv3AdminStatus will override a value of
'enabled' for the interface.rw Status (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.5 |
ospfv3IfRtrPriorityThe priority of this interface. Used in
multi-access networks, this field is used in
the designated-router election algorithm. The
value 0 signifies that the router is not
eligible to become the Designated Router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker.rw DesignatedRouterPriority (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.6 |
ospfv3IfTransitDelayThe estimated number of seconds it takes to transmit
a Link State Update packet over this interface. LSAs
contained in the update packet must have their age
incremented by this amount before transmission. This
value should take into account the transmission and
propagation delays of the interface.rw Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.7 |
ospfv3IfRetransIntervalThe number of seconds between link state
advertisement retransmissions for adjacencies
belonging to this interface. This value is
also used when retransmitting database
description and Link State Request packets.rw Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.8 |
ospfv3IfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the
interface. This value must be the same for all
routers attached to a common network.rw HelloRange UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.9 |
ospfv3IfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before its
neighbors declare the router down on the interface.
This should be some multiple of the Hello interval.
This value must be the same for all routers attached
to a common network.rw Ospfv3DeadIntervalRangeTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.10 |
ospfv3IfPollIntervalThe larger time interval, in seconds, between
the Hello packets sent to an inactive,
non-broadcast multi-access neighbor.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.11 |
ospfv3IfStateThe OSPFv3 interface state. An interface may be
in standby state if there are multiple interfaces
on the link and another interface is active. The
interface may be in Down state if the underlying
IPv6 interface is down or if the admin status is
'disabled' either globally or for the interface.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.12 |
ospfv3IfDesignatedRouterThe Router ID of the Designated Router.ro Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.13 |
ospfv3IfBackupDesignatedRouterThe Router ID of the Backup Designated
Router.ro Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.14 |
ospfv3IfEventsThe number of times this OSPFv3 interface has
changed its state or an error has occurred.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.15 |
ospfv3IfRowStatusThis object permits management of the table by
facilitating actions such as row creation,
construction, and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.16 |
ospfv3IfDemandIndicates whether Demand OSPFv3 procedures
(Hello suppression to FULL neighbors and
setting the DoNotAge flag on propagated LSAs)
should be performed on this interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.17 |
ospfv3IfMetricValueThe metric assigned to this interface.
The default value of the metric is
'Reference Bandwidth / ifSpeed'. The value
of the reference bandwidth can be set
in the ospfv3ReferenceBandwidth object.rw Metric (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.18 |
ospfv3IfLinkScopeLsaCountThe total number of Link-scope link state
advertisements in this link's link state
database.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.19 |
ospfv3IfLinkLsaCksumSumThe 32-bit unsigned sum of the Link-scope link state
advertisements' LS checksums contained in this
link's link state database. The sum can be used
to determine if there has been a change in a
router's link state database or to compare the
link state database of two routers.ro Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.20 |
ospfv3IfDemandNbrProbeIndicates whether or not neighbor probing is
enabled to determine whether or not the neighbor
is inactive. Neighbor probing is disabled by
default.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.21 |
ospfv3IfDemandNbrProbeRetransLimitThe number of consecutive LSA retransmissions before
the neighbor is deemed inactive and the neighbor
adjacency is brought down.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.22 |
ospfv3IfDemandNbrProbeIntervalDefines how often the neighbor will be probed.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.23 |
ospfv3IfTEDisabledIndicates whether or not traffic engineering
is disabled on the interface when traffic
engineering is enabled in the area where the
interface is attached. The object is set
to the value true (1) to disable traffic engineering
on the interface. Traffic engineering is enabled
by default on the interface when traffic engineering
is enabled in the area where the interface is
attached.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.24 |
ospfv3IfLinkLSASuppressionSpecifies whether or not link LSA origination is
suppressed for broadcast or NBMA interface types.
The object is set to value true (1) to suppress
the origination.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.7.1.25 |
ospfv3VirtIfTableInformation about this router's virtual
interfaces that the OSPFv3 Process is configured
to carry on. SEQUENCE OF Ospfv3VirtIfEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.8 |
ospfv3VirtIfEntryInformation about a single virtual interface.
The information in this table is persistent,
and when written, the entity SHOULD save the
change to non-volatile storage. Ospfv3VirtIfEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1 |
ospfv3VirtIfAreaIdThe transit area that the virtual link
traverses. By definition, this is not
Area 0. Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.1 |
ospfv3VirtIfNeighborThe Router ID of the virtual neighbor. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.2 |
ospfv3VirtIfIndexThe local interface index assigned by the
OSPFv3 Process to this OSPFv3 virtual interface.
It is advertised in Hellos sent over the virtual
link and in the router's router-LSAs.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.3 |
ospfv3VirtIfInstIdThe local Interface Instance ID assigned by the
OSPFv3 Process to this OSPFv3 virtual interface.ro Ospfv3IfInstIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.4 |
ospfv3VirtIfTransitDelayThe estimated number of seconds it takes to
transmit a Link State Update packet over this
interface.rw Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.5 |
ospfv3VirtIfRetransIntervalThe number of seconds between link state
advertisement retransmissions for adjacencies
belonging to this interface. This value is
also used when retransmitting database
description and Link State Request packets. This
value should be well over the expected
round-trip time.rw Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.6 |
ospfv3VirtIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the
interface. This value must be the same for the
virtual neighbor.rw HelloRange UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.7 |
ospfv3VirtIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before its
neighbors declare the router down. This should
be some multiple of the Hello interval. This
value must be the same for the virtual
neighbor.rw Ospfv3DeadIntervalRangeTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.8 |
ospfv3VirtIfStateOSPF virtual interface states. The same encoding
as the ospfV3IfTable is used.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.9 |
ospfv3VirtIfEventsThe number of state changes or error events on
this virtual link.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.10 |
ospfv3VirtIfRowStatusThis object permits management of the table by
facilitating actions such as row creation,
construction, and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.11 |
ospfv3VirtIfLinkScopeLsaCountThe total number of Link-scope link state
advertisements in this virtual link's link state
database.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.12 |
ospfv3VirtIfLinkLsaCksumSumThe 32-bit unsigned sum of the Link-scope link state
advertisements' LS checksums contained in this
virtual link's link state database. The sum can be used
to determine if there has been a change in a
router's link state database or to compare the
link state database of two routers.ro Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.8.1.13 |
ospfv3NbrTableA table describing all neighbors in the
locality of the OSPFv3 router. SEQUENCE OF Ospfv3NbrEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.9 |
ospfv3NbrEntryThe information regarding a single neighbor. Ospfv3NbrEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1 |
ospfv3NbrIfIndexThe Local Link ID of the link over which the
neighbor can be reached. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.1 |
ospfv3NbrIfInstIdInterface instance over which the neighbor
can be reached. This ID has local link
significance only. Ospfv3IfInstIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.2 |
ospfv3NbrRtrIdA 32-bit unsigned integer uniquely identifying the
neighboring router in the Autonomous System. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.3 |
ospfv3NbrAddressTypeThe address type of ospfv3NbrAddress. Only IPv6
addresses without zone index are expected.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.4 |
ospfv3NbrAddressThe IPv6 address of the neighbor associated with
the local link.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.5 |
ospfv3NbrOptionsA bit mask corresponding to the neighbor's
options field.ro Integer32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.6 |
ospfv3NbrPriorityThe priority of this neighbor in the designated-
router election algorithm. The value 0 signifies
that the neighbor is not eligible to become the
Designated Router on this particular network.ro DesignatedRouterPriority (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.7 |
ospfv3NbrStateThe state of the relationship with this
neighbor.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.8 |
ospfv3NbrEventsThe number of times this neighbor relationship
has changed state or an error has occurred.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.9 |
ospfv3NbrLsRetransQLenThe current length of the retransmission
queue.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.10 |
ospfv3NbrHelloSuppressedIndicates whether Hellos are being suppressed
to the neighbor.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.11 |
ospfv3NbrIfIdThe Interface ID that the neighbor advertises
in its Hello packets on this link, that is, the
neighbor's local interface index.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.12 |
ospfv3NbrRestartHelperStatusIndicates whether the router is acting
as a graceful restart helper for the neighbor.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.13 |
ospfv3NbrRestartHelperAgeRemaining time in current OSPF graceful restart
interval, if the router is acting as a restart
helper for the neighbor.ro Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.14 |
ospfv3NbrRestartHelperExitReasonDescribes the outcome of the last attempt at acting
as a graceful restart helper for the neighbor.
none: no restart has yet been attempted.
inProgress: a restart attempt is currently underway.
completed: the last restart completed successfully.
timedOut: the last restart timed out.
topologyChanged: the last restart was aborted due to
a topology change.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.9.1.15 |
ospfv3CfgNbrTableA table describing all configured neighbors.
The Configured Neighbors table just gives
OSPFv3 information for sending OSPFv3 packets
to potential neighbors and is typically used
on NBMA and Point-to-Multipoint networks.
Once a Hello is received from a neighbor in
the Configured Neighbor table, an entry for
that neighbor is created in the Neighbor table
and adjacency state is maintained there.
Neighbors on multi-access or Point-to-Point
networks can use multicast addressing, so only
Neighbor table entries are created for them. SEQUENCE OF Ospfv3CfgNbrEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.10 |
ospfv3CfgNbrEntryThe information regarding a single configured
neighbor.
The information in this table is persistent,
and when written, the entity SHOULD save the
change to non-volatile storage. Ospfv3CfgNbrEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.10.1 |
ospfv3CfgNbrIfIndexThe Local Link ID of the link over which the
neighbor can be reached. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.10.1.1 |
ospfv3CfgNbrIfInstIdInterface instance over which the neighbor
can be reached. This ID has local link
significance only. Ospfv3IfInstIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.10.1.2 |
ospfv3CfgNbrAddressTypeThe address type of ospfv3NbrAddress. Only IPv6
addresses without zone index are expected. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.10.1.3 |
ospfv3CfgNbrAddressThe IPv6 address of the neighbor associated with
the local link. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.10.1.4 |
ospfv3CfgNbrPriorityThe priority of this neighbor in the designated-
router election algorithm. The value 0 signifies
that the neighbor is not eligible to become the
Designated Router on this particular network.rw DesignatedRouterPriority (OSPF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.10.1.5 |
ospfv3CfgNbrRowStatusThis object permits management of the table by
facilitating actions such as row creation,
construction, and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.10.1.6 |
ospfv3VirtNbrTableA table describing all virtual neighbors. SEQUENCE OF Ospfv3VirtNbrEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.11 |
ospfv3VirtNbrEntryVirtual neighbor information. Ospfv3VirtNbrEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1 |
ospfv3VirtNbrAreaThe transit area Identifier. Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.1 |
ospfv3VirtNbrRtrIdA 32-bit integer uniquely identifying the
neighboring router in the Autonomous System. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.2 |
ospfv3VirtNbrIfIndexThe local Interface ID for the virtual link over
which the neighbor can be reached.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.3 |
ospfv3VirtNbrIfInstIdThe interface instance for the virtual link over
which the neighbor can be reached.ro Ospfv3IfInstIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.4 |
ospfv3VirtNbrAddressTypeThe address type of ospfv3VirtNbrAddress. Only IPv6
addresses without zone index are expected.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.5 |
ospfv3VirtNbrAddressThe IPv6 address advertised by this virtual neighbor.
It must be a global scope address.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.6 |
ospfv3VirtNbrOptionsA bit mask corresponding to the neighbor's options
field.ro Integer32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.7 |
ospfv3VirtNbrStateThe state of the virtual neighbor relationship.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.8 |
ospfv3VirtNbrEventsThe number of times this virtual link has
changed its state or an error has occurred.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime.ro Counter32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.9 |
ospfv3VirtNbrLsRetransQLenThe current length of the retransmission
queue.ro Gauge32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.10 |
ospfv3VirtNbrHelloSuppressedIndicates whether Hellos are being suppressed
to the neighbor.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.11 |
ospfv3VirtNbrIfIdThe Interface ID that the neighbor advertises
in its Hello packets on this virtual link, that is,
the neighbor's local Interface ID.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.12 |
ospfv3VirtNbrRestartHelperStatusIndicates whether the router is acting
as a graceful restart helper for the neighbor.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.13 |
ospfv3VirtNbrRestartHelperAgeRemaining time in the current OSPF graceful restart
interval, if the router is acting as a restart
helper for the neighbor.ro Ospfv3UpToRefreshIntervalTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.14 |
ospfv3VirtNbrRestartHelperExitReasonDescribes the outcome of the last attempt at acting
as a graceful restart helper for the neighbor.
none: no restart has yet been attempted.
inProgress: a restart attempt is currently underway.
completed: the last restart completed successfully.
timedOut: the last restart timed out.
topologyChanged: the last restart was aborted due to
a topology change.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.11.1.15 |
ospfv3AreaAggregateTableThe Area Aggregate Table acts as an adjunct
to the Area Table. It describes those address
aggregates that are configured to be propagated
from an area. Its purpose is to reduce the amount
of information that is known beyond an area's
borders.
A range of IPv6 prefixes specified by a
prefix / prefix length pair. Note that if
ranges are configured such that one range
subsumes another range, the most specific
match is the preferred one. SEQUENCE OF Ospfv3AreaAggregateEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.12 |
ospfv3AreaAggregateEntryA single area aggregate entry.
Information in this table is persistent, and
when this object is written, the entity SHOULD
save the change to non-volatile storage. Ospfv3AreaAggregateEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1 |
ospfv3AreaAggregateAreaIDThe area the Address Aggregate is to be found
within. Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.1 |
ospfv3AreaAggregateAreaLsdbTypeThe type of the Address Aggregate. This field
specifies the Area LSDB type that this Address
Aggregate applies to. Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.2 |
ospfv3AreaAggregatePrefixTypeThe prefix type of ospfv3AreaAggregatePrefix. Only
IPv6 addresses are expected. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.3 |
ospfv3AreaAggregatePrefixThe IPv6 prefix. InetAddress .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.4 |
ospfv3AreaAggregatePrefixLengthThe length of the prefix (in bits). A prefix can
not be shorter than 3 bits. InetAddressPrefixLength .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.5 |
ospfv3AreaAggregateRowStatusThis object permits management of the table by
facilitating actions such as row creation,
construction, and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.6 |
ospfv3AreaAggregateEffectPrefixes subsumed by ranges will either trigger the
advertisement of the indicated aggregate
(advertiseMatching) or result in the prefix not
being advertised at all outside the area.rw Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.7 |
ospfv3AreaAggregateRouteTagThis tag is advertised only in the summarized
As-External LSA when summarizing from NSSA-LSAs to
AS-External-LSAs.rw Unsigned32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.12.1.8 |
ospfv3VirtLinkLsdbTableThe OSPFv3 Process's Link-scope LSDB for virtual
interfaces. The LSDB contains the Link-scope link
state advertisements from virtual interfaces. SEQUENCE OF Ospfv3VirtLinkLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.13 |
ospfv3VirtLinkLsdbEntryA single Link-scope link state advertisement
for a virtual interface. Ospfv3VirtLinkLsdbEntry .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1 |
ospfv3VirtLinkLsdbIfAreaIdThe transit area that the virtual link
traverses. By definition, this is not
Area 0. Ospfv3AreaIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.1 |
ospfv3VirtLinkLsdbIfNeighborThe Router ID of the virtual neighbor. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.2 |
ospfv3VirtLinkLsdbTypeThe type of the link state advertisement.
Each link state type has a separate
advertisement format. Link-scope LSAs unrecognized
by the router are also stored in this database. Unsigned32(0..'FFFFFFFF'h) .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.3 |
ospfv3VirtLinkLsdbRouterIdThe 32-bit number that uniquely identifies the
originating router in the Autonomous System. Ospfv3RouterIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.4 |
ospfv3VirtLinkLsdbLsidThe Link State ID is an LS type-specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics. Ospfv3LsIdTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.5 |
ospfv3VirtLinkLsdbSequenceThe sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number, the more recent the
advertisement.ro Ospfv3LsaSequenceTC .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.6 |
ospfv3VirtLinkLsdbAgeThis field is the age of the link state
advertisement in seconds. The high-order bit
of the LS age field is considered the DoNotAge
bit for support of on-demand circuits.ro Ospfv3LsaAgeTC UNITS "seconds" .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.7 |
ospfv3VirtLinkLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.8 |
ospfv3VirtLinkLsdbAdvertisementThe entire link state advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.9 |
ospfv3VirtLinkLsdbTypeKnownThe value true (1) indicates that the LSA type is
recognized by this router.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3727.20.20.3.1.191.1.13.1.10 |
ospfv3NotificationEntry OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.191.1.14 |
ospfv3ConfigErrorTypePotential types of configuration conflicts.
Used by the ospfv3ConfigError and
ospfv3ConfigVirtError notifications.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.14.1 |
ospfv3PacketTypeOSPFv3 packet types.ro Enumeration .1.3.6.1.4.1.3727.20.20.3.1.191.1.14.2 |
ospfv3PacketSrcThe IPv6 address of an inbound packet that cannot
be identified by a neighbor instance.
Only IPv6 addresses without zone index are expected.ro InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.3727.20.20.3.1.191.1.14.3 |
ospfv3Conformance OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.191.2 |
ospfv3Groups OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.191.2.1 |
ospfv3Compliances OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.191.2.2 |