INT-SERV-MIB

AI MIB Summary

INT-SERV-MIB provides the management interface for monitoring and configuring Integrated Services (IntServ) QoS parameters, specifically tracking RSVP reservation states, flow specifications, and admission control metrics across network devices. This module enables administrators to verify resource allocation for individual data flows and manage the signaling state of RSVP sessions to ensure strict bandwidth guarantees.

The MIB module to describe the Integrated Services Protocol

Objects

Active

Status

Dependencies

Imported Objects

Objects

48 total

Object Name	Syntax	OID
intSrv OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52`
RFC1155-SMI Unknown `.1.3.6.1.4.1.3727.20.20.3.1.52`	Unknown	`.1.3.6.1.4.1.3727.20.20.3.1.52`
intSrvObjects OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1`
intSrvIfAttribTableThe reservable attributes of the system's in- terfaces. SEQUENCE OF IntSrvIfAttribEntry `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1`	SEQUENCE OF IntSrvIfAttribEntry	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1`
intSrvIfAttribEntryThe reservable attributes of a given inter- face. IntSrvIfAttribEntry `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1`	IntSrvIfAttribEntry	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1`
intSrvIfAttribAllocatedBitsThe number of bits/second currently allocated to reserved sessions on the interface.ro BitRate -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.1`	BitRate -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.1`
intSrvIfAttribMaxAllocatedBitsThe maximum number of bits/second that may be allocated to reserved sessions on the inter- face.rw BitRate -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.2`	BitRate -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.2`
intSrvIfAttribAllocatedBufferThe amount of buffer space required to hold the simultaneous burst of all reserved flows on the interface.ro BurstSize -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.3`	BurstSize -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.3`
intSrvIfAttribFlowsThe number of reserved flows currently active on this interface. A flow can be created ei- ther from a reservation protocol (such as RSVP or ST-II) or via configuration information.ro Gauge `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.4`	Gauge	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.4`
intSrvIfAttribPropagationDelayThe amount of propagation delay that this in- terface introduces in addition to that intro- diced by bit propagation delays.rw INTEGER -- Units -- microseconds `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.5`	INTEGER -- Units -- microseconds	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.5`
intSrvIfAttribStatus'active' on interfaces that are configured for RSVP.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } `.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.6`	RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- }	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.1.1.6`
intSrvFlowTableInformation describing the reserved flows us- ing the system's interfaces. SEQUENCE OF IntSrvFlowEntry `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2`	SEQUENCE OF IntSrvFlowEntry	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2`
intSrvFlowEntryInformation describing the use of a given in- terface by a given flow. The counter intSrvFlowPoliced starts counting at the in- stallation of the flow. IntSrvFlowEntry `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1`	IntSrvFlowEntry	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1`
intSrvFlowNumberThe number of this flow. This is for SNMP In- dexing purposes only and has no relation to any protocol value. SessionNumber -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.1`	SessionNumber -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.1`
intSrvFlowTypeThe type of session (IP4, IP6, IP6 with flow information, etc).rw SessionType -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.2`	SessionType -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.2`
intSrvFlowOwnerThe process that installed this flow in the queue policy database.rw Enumeration `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.3`	Enumeration	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.3`
intSrvFlowDestAddrThe destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'ac- tive'.rw OCTET STRING `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.4`	OCTET STRING	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.4`
intSrvFlowSenderAddrThe source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'. This object may not be changed when the value of the RowStatus object is 'active'.rw OCTET STRING `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.5`	OCTET STRING	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.5`
intSrvFlowDestAddrLengthThe length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'active'.rw INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.6`	INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.6`
intSrvFlowSenderAddrLengthThe length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'active'.rw INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.7`	INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.7`
intSrvFlowProtocolThe IP Protocol used by a session. This ob- ject may not be changed when the value of the RowStatus object is 'active'.rw Protocol -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.8`	Protocol -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.8`
intSrvFlowDestPortThe UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by intSrvResvFwdProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A value of zero indicates that the IP protocol in use does not have ports. This ob- ject may not be changed when the value of the RowStatus object is 'active'.rw Port -- Rsyntax OCTET STRING `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.9`	Port -- Rsyntax OCTET STRING	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.9`
intSrvFlowPortThe UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by intSrvResvFwdProtocol is 50 (ESP) or 51 (AH), this represents a generalized port identifier (GPI). A value of zero indicates that the IP protocol in use does not have ports. This ob- ject may not be changed when the value of the RowStatus object is 'active'.rw Port -- Rsyntax OCTET STRING `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.10`	Port -- Rsyntax OCTET STRING	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.10`
intSrvFlowFlowIdThe flow ID that this sender is using, if this is an IPv6 session.ro INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.11`	INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.11`
intSrvFlowInterfaceThe ifIndex value of the interface on which this reservation exists.rw InterfaceIndex -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.12`	InterfaceIndex -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.12`
intSrvFlowIfAddrThe IP Address on the ifEntry on which this reservation exists. This is present primarily to support those interfaces which layer multi- ple IP Addresses on the interface.rw OCTET STRING `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.13`	OCTET STRING	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.13`
intSrvFlowRateThe Reserved Rate of the sender's data stream. If this is a Controlled Load service flow, this rate is derived from the Tspec rate parameter (r). If this is a Guaranteed service flow, this rate is derived from the Rspec clearing rate parameter (R).rw BitRate -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.14`	BitRate -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.14`
intSrvFlowBurstThe size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option.rw BurstSize -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.15`	BurstSize -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.15`
intSrvFlowWeightThe weight used to prioritize the traffic. Note that the interpretation of this object is implementation-specific, as implementations vary in their use of weighting procedures.rw INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.16`	INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.16`
intSrvFlowQueueThe number of the queue used by this traffic. Note that the interpretation of this object is implementation-specific, as implementations vary in their use of queue identifiers.rw INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.17`	INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.17`
intSrvFlowMinTUThe minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.rw MessageSize -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.18`	MessageSize -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.18`
intSrvFlowMaxTUThe maximum datagram size for this flow that will conform to the traffic specification. This value cannot exceed the MTU of the interface.rw MessageSize -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.19`	MessageSize -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.19`
intSrvFlowBestEffortThe number of packets that were remanded to best effort service.ro Counter `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.20`	Counter	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.20`
intSrvFlowPolicedThe number of packets policed since the incep- tion of the flow's service.ro Counter `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.21`	Counter	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.21`
intSrvFlowDiscardIf 'true', the flow is to incur loss when traffic is policed. If 'false', policed traff- ic is treated as best effort traffic.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.22`	TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- }	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.22`
intSrvFlowServiceThe QoS service being applied to this flow.ro QosService -- Rsyntax INTEGER { -- bestEffort(1), -- guaranteedDelay(2), -- controlledLoad(5) -- } `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.23`	QosService -- Rsyntax INTEGER { -- bestEffort(1), -- guaranteedDelay(2), -- controlledLoad(5) -- }	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.23`
intSrvFlowOrderIn the event of ambiguity, the order in which the classifier should make its comparisons. The row with intSrvFlowOrder=0 is tried first, and comparisons proceed in the order of in- creasing value. Non-serial implementations of the classifier should emulate this behavior.rw INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.24`	INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.24`
intSrvFlowStatus'active' for all active flows. This object may be used to install static classifier infor- mation, delete classifier information, or au- thorize such.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } `.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.25`	RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- }	`.1.3.6.1.4.1.3727.20.20.3.1.52.1.2.1.25`
intSrvGenObjects OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.2`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.2`
intSrvFlowNewIndexThis object is used to assign values to intSrvFlowNumber as described in 'Textual Con- ventions for SNMPv2'. The network manager reads the object, and then writes the value back in the SET that creates a new instance of intSrvFlowEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated; If the SET succeeds, then the ob- ject is incremented, and the new instance is created according to the manager's directions.rw TestAndIncr -- Rsyntax INTEGER `.1.3.6.1.4.1.3727.20.20.3.1.52.2.1`	TestAndIncr -- Rsyntax INTEGER	`.1.3.6.1.4.1.3727.20.20.3.1.52.2.1`
intSrvNotifications OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.3`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.3`
intSrvConformance OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.4`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.4`
intSrvGroups OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.4.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.4.1`
intSrvIfAttribGroup OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.4.1.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.4.1.1`
intSrvFlowsGroup OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.4.1.2`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.4.1.2`
intSrvGenObjectsGroup OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.4.1.3`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.4.1.3`
intSrvCompliances OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.4.2`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.4.2`
intSrvCompliance OBJECT IDENTIFIER `.1.3.6.1.4.1.3727.20.20.3.1.52.4.2.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.3727.20.20.3.1.52.4.2.1`