HUAWEI-L2MULTICAST-MIB
AI MIB Summary
The HUAWEI-L2MULTICAST-MIB module enables monitoring and management of IGMP Snooping states and multicast forwarding tables on Huawei Layer 2 switches. It tracks specific metrics including active multicast group memberships, learned MAC addresses, and interface-specific snooping counters to verify selective traffic delivery.
The MIB module for IGMP Snooping feature.
Internet Group Management Protocol (IGMP) is the protocol used by IPv4 end hosts to indicate their interest in receiving multicast traffic for certain multicast groups to neighboring multicast routers. IGMP Snooping is a switch protocol. A switch that implements IGMP Snooping listens to the IGMP messages exchanged between the hosts and router, then provides selective transmission of multicast traffic based on multicast mac destination address or multicast group address.
Main OID:
hwL2MultiCastMIB.1.3.6.1.4.1.2011.5.25.181
470
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
470 total| Object Name |
|---|
hwL2MultiCastMIBThe MIB module for IGMP Snooping feature.
Internet Group Management Protocol (IGMP) is the protocol used
by IPv4 end hosts to indicate their interest in receiving
multicast traffic for certain multicast groups to neighboring
multicast routers.
IGMP Snooping is a switch protocol. A switch that implements
IGMP Snooping listens to the IGMP messages exchanged between
the hosts and router, then provides selective transmission of
multicast traffic based on multicast mac destination address
or multicast group address. MODULE-IDENTITY .1.3.6.1.4.1.2011.5.25.181 |
hwIgspMibObject OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1 |
hwIgspSystemInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.1 |
hwIgmpSnoopingEnabledIGMP snooping is enabled or disabled in the global view:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.1.1 |
hwSendQueryEnabledThe sending of query packets is enabled or disabled:
1: enabled
2: disabled
The default value is 2.
Note: Ensure that you query and configure this object after hwIgmpSnoopingEnabled is configured.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.1.2 |
hwSendQuerySourceIpAddrThe source IP addresses of the Query messages sent by a device.
The value ranges from 1.0.0.0 to 223.255.255.255.
The default value is 192.168.0.1.rw IpAddress .1.3.6.1.4.1.2011.5.25.181.1.1.3 |
hwL2mcCacTrapIntervalThe CAC trap interval. The default is 300.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.1.4 |
hwL2mcPerformanceStatisticsIntervalThe Performance statistic interval. The default is 15 minute.rw Integer32(5 |15 | 30 | 60) .1.3.6.1.4.1.2011.5.25.181.1.1.5 |
hwL2mcCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.2 |
hwL2mcCfgTableThis table describes the configurations of IGMP snooping in a VLAN or a VSI. SEQUENCE OF HWL2mcCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.2.1 |
hwL2mcCfgEntryAn entry is created for each active VLAN or VSI in the device
and deleted when the VLAN or VSI becomes inactive. HWL2mcCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.2.1.1 |
hwL2mcVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.1 |
hwL2mcVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.2 |
hwL2mcEnabledWhether IGMP snooping is enabled in a VLAN or a VSI:
1:enabled
2:disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.3 |
hwL2mcRouterAgingTimeThe aging time of an interface on a router.
The value ranges from 1 to 1000, in seconds.
The default value is 180, which router port is created by Igmp Query message.
And when it is created by PIM hello messge, the default value is the time of Holdtime in the message.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.4 |
hwL2mcMaxQueryRespTimeThe maximum response time.
The value ranges from 1 to 25, in seconds.
The default value is 10, in seconds.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.5 |
hwL2mcLastMemQueryIntervalThe last member query interval.
The value ranges from 1 to 5, in seconds.
The default value is 1, in seconds.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.6 |
hwL2mcQueryIntervalThe query interval.
The value ranges from 1 to 65535, in seconds.
The default value is 60, in seconds.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.7 |
hwL2mcRobustCountThe robustness variable.
The value ranges from 2 to 5.
The default value is 2.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.8 |
hwL2mcCheckRouterAlertWhether to check the router-alert of a packet.
The default value is false.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.9 |
hwL2mcSendRouterAlertWhether to send the router-alert of a packet.
The default value is true.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.10 |
hwL2mcIgmpVersionThe version of the IGMP packets.
The value ranges from 1 to 3.
The default value is 2.rw Enumeration .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.11 |
hwL2mcFwdModeThe forwarding mode:
1: IP
2: MAC
The default value is 1.rw Enumeration .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.12 |
hwL2mcPromptLeaveEnableWhether the prompt leave is enabled:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.13 |
hwL2mcPromptLeaveAclNumWhether the prompt leave complies with the ACL rules. The ACL number can be set.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that no ACL number is set.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.14 |
hwL2mcRouterPortLearningEnableWhether interface learning is enabled or not in a VLAN:
1: enabled
2: disabled
The default value is 1.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.15 |
hwL2mcReportSuppressEnableWhether the suppression of the IGMP Report message (proxy) is enabled:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.16 |
hwL2mcIgmpQuerierEnableWhether the querier is enabled:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.17 |
hwL2mcIgmpSsmMappingEnableWhether Ssm-Mapping is enabled:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.18 |
hwL2mcSsmAclNumThat SSM complies with the ACL number.
The ACL number ranges from 2000 to 2999.
The default value is 0, indicating that no ACL number is set.rw Integer32(0|2000..2999) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.19 |
hwL2mcProxyRouterProtocolPassWhether protocol packets are allowed to pass a router port when proxy is enabled.
The default value is false.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.20 |
hwL2mcAsmSsmFlagThat restric study:
1: asm-ssm
2: asm-only
3: ssm-only
The default value is 1.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.21 |
hwL2mcSrcLifeTimeThat source aging time:
range from 60 to 1000
The default value is 210.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.22 |
hwL2mcPerformanceStatisticsThat performance statistic is enabled:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.23 |
hwL2mcQuerierElectionThat querier election is enabled:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.24 |
hwETrackEnableThe host explicity track is enabled:
1: enabled
2: disabled
The default value is 2.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.25 |
hwL2mcBackupQueryFwdThat IGMP query forward :
1: Do not forward;
2: Forward without replace source MAC address;
3: Forward with replace source MAC address;
The default value is 1.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.26 |
hwL2mcBackupReportFwdThat IGMP report forward :
1: Do not forward;
2: Forward without replace source MAC address;
3: Forward with replace source MAC address;
The default value is 1.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.27 |
hwL2mcQuerySuppressWhether supress IGMP query packet or time of suppress interval.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.28 |
hwL2mcRtLearnRingLinkageWhether responed to link state for SEP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.29 |
hwL2mcIgmpIpPolicyAclNumWhether the IGMP ip policy complies with the ACL rules. The ACL number can be set.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that no ACL number is set.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.30 |
hwL2mcIgmpSsmMappingPolicyThe policy name of SSM mapping.rw DisplayString .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.31 |
hwL2mcRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.2.1.1.100 |
hwL2mcStatisticsInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.3 |
hwL2mcStatisticsTableTable contains VLAN or VSI statistics information
for IGMP Snooping. SEQUENCE OF HWL2mcStatisticsEntry .1.3.6.1.4.1.2011.5.25.181.1.3.1 |
hwL2mcStatisticsEntryAn entry is created for each active VLAN or VSI in the device
and deleted when the VLAN or VSI becomes inactive. HWL2mcStatisticsEntry .1.3.6.1.4.1.2011.5.25.181.1.3.1.1 |
hwL2mcStatsVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.1 |
hwL2mcStatsVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.2 |
hwL2mcRecvIgmpV1ReportNumThe number of IGMPv1 Report messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.3 |
hwL2mcRecvIgmpV2ReportNumThe number of IGMPv2 Report messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.4 |
hwL2mcRecvIgmpV3ReportNumThe number of IGMPv3 Report messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.5 |
hwL2mcRecvIgmpLeaveNumThe number of IGMP Leave messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.6 |
hwL2mcRecvIgmpV1QueryNumThe number of IGMPv1 Query messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.7 |
hwL2mcRecvIgmpV2QueryNumThe number of IGMPv2 Query messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.8 |
hwL2mcRecvIgmpV3QueryNumThe number of IGMPv3 Query messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.9 |
hwL2mcRecvPimHelloNumThe number of PIM Hello messages received in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.10 |
hwL2mcSendQueryNumThe number of IGMP Query messages (the source address is 0) in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.11 |
hwL2mcSendQuerySourceNumThe number of IGMP Query messages (the source address is not 0) in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.12 |
hwL2mcProxyGenQueryNumThe number of Query messages sent by the proxy in a VLAN or a VSI.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.13 |
hwL2mcProxyGroupQueryNumThe number of Query messages sent by the proxy in a VLAN or a VSI to a specified group.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.14 |
hwL2mcProxyGroupSourceQueryNumThe number of Query messages sent by the proxy in a VLAN or a VSI to a specified source group.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.15 |
hwL2mcIgmpPacketClearStatsWhether to clear the statistics of IGMP snooping. If the value is 1, it indicates that the statistics need to be cleared.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.3.1.1.30 |
hwL2mcFwdInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.4 |
hwL2mcFwdTableTable contains l2 multicast forward information
for IGMP Snooping. SEQUENCE OF HWL2mcFwdEntry .1.3.6.1.4.1.2011.5.25.181.1.4.1 |
hwL2mcFwdEntryAn entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when
a forwarding table entry deleted. HWL2mcFwdEntry .1.3.6.1.4.1.2011.5.25.181.1.4.1.1 |
hwL2mcFwdVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.1 |
hwL2mcFwdVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.2 |
hwL2mcFwdGroupAddressThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.3 |
hwL2mcFwdSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.4 |
hwL2mcFwdPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.5 |
hwL2mcFwdPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.6 |
hwL2mcFwdPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.7 |
hwL2mcFwdPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.8 |
hwL2mcFwdPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.9 |
hwL2mcFwdVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.10 |
hwL2mcFwdAddressTypeThe address type of an entry:
1: IP
2: MAC
The default value is 1.ro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.11 |
hwL2mcFwdHostFlag1The mode to create an interface on the host:
1: static
2: dynamic
3: static and dynamic
4: invalidro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.18 |
hwL2mcFwdHostFlag2Whether an interface on the host is created through SSM-mapping:
1: non-mapping
2: mappingro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.19 |
hwL2mcFwdHostFlag3The type of an interface created on a router:
1: Interface connected to the host
2: Router interface that replicates multicast data flowsro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.20 |
hwL2mcFwdHostFlag4Indicates (S, G) table created :
1: from port;
2: from static;
3: from both
the default value is 1ro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.4.1.1.21 |
hwL2mcGroupInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.5 |
hwL2mcGroupInfoTableTable contains l2 multicast group information
for IGMP Snooping. SEQUENCE OF HWL2mcGroupInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.5.1 |
hwL2mcGroupInfoEntryAn entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when
a forwarding table entry deleted. HWL2mcGroupInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.5.1.1 |
hwL2mcGroupVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.1 |
hwL2mcGroupVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.2 |
hwL2mcGroupGroupAddressThe IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.3 |
hwL2mcGroupSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.4 |
hwL2mcPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.5 |
hwL2mcGroupPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.6 |
hwL2mcGroupPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.7 |
hwL2mcGroupPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.8 |
hwL2mcGroupPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.9 |
hwL2mcGroupVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.10 |
hwL2mcSourceUpTimeHow long the source group exists in the forwarding entry.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.14 |
hwL2mcSourceExpiresThe timeout period of the source group in the forwarding entry, that is, the aging time of the source group.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.15 |
hwL2mcGroupUpTimeHow long the group exists in the forwarding entry.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.16 |
hwL2mcGroupExpiresWhen the group expires in the forwarding entry, that is, the aging time of the source group.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.17 |
hwL2mcGroupFilterFlagThe filtering mode:
1: include
2: exclude
3: invalidro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.18 |
hwL2mcGroupHostFlag1The mode to create an interface on the host:
1: static
2: dynamic
3: static and dynamic
4: invalidro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.19 |
hwL2mcGroupHostFlag2Whether an interface on the host is created through SSM-mapping:
1: non-mapping
2: mappingro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.20 |
hwL2mcGroupRowStatusThe row status.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.5.1.1.100 |
hwL2mcGroupCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.6 |
hwL2mcGroupCfgTableTable contains l2 multicast static group information
for IGMP Snooping. SEQUENCE OF HWL2mcGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.6.1 |
hwL2mcGroupCfgEntryAn entry is created for each active VLAN or VSI in the device create a static group entry and delete when
a static group entry deleted. HWL2mcGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.6.1.1 |
hwGroupCfgPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.1 |
hwGroupCfgPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.2 |
hwGroupCfgPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.3 |
hwGroupCfgPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.4 |
hwGroupCfgPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.5 |
hwGroupCfgVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.6 |
hwGroupCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.7 |
hwGroupCfgVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.8 |
hwGroupCfgGroupAddressThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.9 |
hwGroupCfgSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.10 |
hwGroupCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.6.1.1.100 |
hwL2mcSsmSourceInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.7 |
hwL2mcSsmSourceTableThis table contains the configuration of the source address list of SSM-Mapping. SEQUENCE OF HWL2mcSsmSourceEntry .1.3.6.1.4.1.2011.5.25.181.1.7.1 |
hwL2mcSsmSourceEntryAn entry is created for each active VLAN or VSI in the device add an entry for SSM-Mapping. HWL2mcSsmSourceEntry .1.3.6.1.4.1.2011.5.25.181.1.7.1.1 |
hwL2mcSsmSourceVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.7.1.1.1 |
hwL2mcSsmSourceVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.7.1.1.2 |
hwL2mcSsmGroupAddressThe IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.7.1.1.3 |
hwL2mcSsmGroupLenThe mask length of a multicast group. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.7.1.1.4 |
hwL2mcSsmSourceAddressThe source address of SSM-Mapping, which serves as an index of this table. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.7.1.1.5 |
hwL2mcSsmSourceRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.7.1.1.100 |
hwL2mcPortGroupPolicyCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.8 |
hwL2mcPortGroupPolicyCfgTableIn this table, you can query or configure a group policy to filter entries on a port. SEQUENCE OF HWL2mcPortGroupPolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.8.1 |
hwL2mcPortGroupPolicyCfgEntryAn entry is created for each active VLAN or VSI in the device when a group policy added. HWL2mcPortGroupPolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.8.1.1 |
hwPortGroupPolicyPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
9: batch config qinq port ce VLAN ID
10: batch config dot1q termination port ce VLAN ID
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.1 |
hwPortGroupPolicyPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.2 |
hwPortGroupPolicyPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.3 |
hwPortGroupPolicyPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.4 |
hwPortGroupPolicyPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.5 |
hwPortGroupPolicyVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.6 |
hwPortGroupPolicyVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.7 |
hwPortGroupPolicyVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.8 |
hwPortGroupPolicyAclNumThe number of a basic ACL.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that the value is invalid.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.9 |
hwPortGroupPolicyIgmpVersionThe IGMP version.
The value ranges from 1 to 4.
The default is 4, indicating that no version is specified.rw Enumeration .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.10 |
hwPortGroupPolicyRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.8.1.1.100 |
hwL2mcChnlCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.9 |
hwL2mcChnlCfgTableThis table describes the configurations of a channel. SEQUENCE OF HWL2mcChnlCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.9.1 |
hwL2mcChnlCfgEntryAn entry of channel is created for each VLAN or VSI in the device create an channel. HWL2mcChnlCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.9.1.1 |
hwChnlCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN.
If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.9.1.1.1 |
hwChnlCfgVsiNameThe name of a VSI.
If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.9.1.1.2 |
hwChnlCfgChnlNameThe channel name. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.9.1.1.3 |
hwChnlCfgChnlTypeThe channel type:
1: SSM
2: ASMrw Enumeration .1.3.6.1.4.1.2011.5.25.181.1.9.1.1.9 |
hwChnlCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.9.1.1.100 |
hwL2mcLimitInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.10 |
hwL2mcLimitTableThis table describes the configurations of IGMP snooping CAC in a VLAN or a VSI. SEQUENCE OF HWL2mcLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.10.1 |
hwL2mcLimitEntryAn entry is created for each IGMP snooping CAC in a VLAN or a VSI. HWL2mcLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.10.1.1 |
hwL2mcLimitVlanIndexThe VLAN ID, which is the configuration index in a VLAN.
If a VSI is specified, the value is 4095. If both hwVlanLimitVlanIndex and hwVlanLimitVSIName are invalid, the configuration is global.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.1 |
hwL2mcLimitVsiNameThe name of a VSI. If a VLAN is specified, the value is 32.
If both hwVlanLimitVlanIndex and hwVlanLimitVSIName are invalid, the configuration is global. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.2 |
hwL2mcLimitChnlNameThe channel name. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.3 |
hwL2mcLimitMaxEntryThe maximum number of forwarding entries. The value 0 indicates that the number is invalid.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.4 |
hwL2mcLimitEntryCntThe number of current forwarding entries.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.5 |
hwL2mcLimitMaxBandWidthThe maximum bandwidth. The value 0 indicates that the bandwidth is invalid.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.6 |
hwL2mcLimitBandWidthThe current bandwidth.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.7 |
hwL2mcLimitAclThe number of ACL for the multicast groups that do not need to be configured with CAC limit.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that the number is invalid.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.8 |
hwL2mcLimitCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.10.1.1.100 |
hwL2mcPortLimitInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.11 |
hwL2mcPortLimitTableThis table describes the configurations of IGMP snooping CAC on an interface. SEQUENCE OF HWL2mcPortLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.11.1 |
hwL2mcPortLimitEntryAn entry is created for each IGMP snooping CAC on an interface. HWL2mcPortLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.11.1.1 |
hwPortLimitVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.1 |
hwPortLimitVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.2 |
hwPortLimitPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
9: batch config qinq port ce VLAN ID
10: batch config dot1q termination port ce VLAN ID HWPortType .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.3 |
hwPortLimitIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.4 |
hwPortLimitPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.5 |
hwPortLimitCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.6 |
hwPortLimitPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.7 |
hwPortLimitVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.8 |
hwPortLimitChnlNameThe channel name. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.9 |
hwPortLimitAclThe number of ACL for the multicast groups that do not need to be configured with CAC limit.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that the number is invalid.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.10 |
hwPortLimitMaxEntryThe maximum number of forwarding entries. The value 0 indicates that the number is invalid.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.11 |
hwPortLimitEntryCntThe number of current forwarding entries.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.12 |
hwPortLimitMaxBandWidthThe maximum bandwidth. The value 0 indicates that the bandwidth is invalid.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.13 |
hwPortLimitBandWidthThe current bandwidth.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.14 |
hwPortLimitCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.11.1.1.100 |
hwL2mcFastChnlCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.12 |
hwL2mcFastChnlCfgTableTable contains l2 multicast fast forward information for IGMP Snooping. SEQUENCE OF HWL2mcFastChnlCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.12.1 |
hwL2mcFastChnlCfgEntryAn entry is created for each IGMP snooping fast channel. HWL2mcFastChnlCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.12.1.1 |
hwL2mcFastChnlCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.12.1.1.1 |
hwL2mcFastChnlCfgVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.12.1.1.2 |
hwL2mcFastChnlCfgGroupAddressThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.12.1.1.3 |
hwL2mcFastChnlCfgGroupLenThe mask length of a multicast group address. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.12.1.1.4 |
hwL2mcFastChnlCfgSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.12.1.1.5 |
hwL2mcFastChnlCfgSourceLenThe mask length of a multicast source address. Integer32(0|16..32) .1.3.6.1.4.1.2011.5.25.181.1.12.1.1.6 |
hwL2mcFastChnlCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.12.1.1.100 |
hwL2mcRouterPortInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.13 |
hwL2mcRouterPortInfoTableTable contains l2 multicast router port information for IGMP Snooping. SEQUENCE OF HWL2mcRouterPortInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.13.1 |
hwL2mcRouterPortInfoEntryAn entry is created for each IGMP snooping router port on an interface. HWL2mcRouterPortInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.13.1.1 |
hwL2mcRouterPortVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.1 |
hwL2mcRouterPortVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.2 |
hwL2mcRouterPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.3 |
hwL2mcRouterPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.4 |
hwL2mcRouterPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.5 |
hwL2mcRouterPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.6 |
hwL2mcRouterPortPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.7 |
hwL2mcRouterPortVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.8 |
hwL2mcRouterPortGroupUpTimeHow long the group exists in the forwarding entry.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.16 |
hwL2mcRouterPortGroupExpiresThe timeout period of the router port, that is, the aging time of the router port.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.17 |
hwL2mcRouterPortGroupHostFlag1The mode to create an interface on the host:
1: static
2: dynamic
3: static and dynamicro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.13.1.1.19 |
hwL2mcRouterPortCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.14 |
hwL2mcRouterPortCfgTableTable contains l2 multicast configuration of router port for IGMP Snooping. SEQUENCE OF HWL2mcRouterPortCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.14.1 |
hwL2mcRouterPortCfgEntryAn entry is created for each IGMP snooping static router port on an interface. HWL2mcRouterPortCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.14.1.1 |
hwL2mcRouterPortCfgPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.1 |
hwL2mcRouterPortCfgPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.2 |
hwL2mcRouterPortCfgPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.3 |
hwL2mcRouterPortCfgPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.4 |
hwL2mcRouterPortCfgPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.5 |
hwL2mcRouterPortCfgVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.6 |
hwL2mcRouterPortCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.7 |
hwL2mcRouterPortCfgVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.8 |
hwL2mcRouterPortCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.14.1.1.100 |
hwL2mcChnlGroupCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.15 |
hwL2mcChnlGroupCfgTableThis table describes the group configurations of a channel. SEQUENCE OF HWL2mcChnlGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.15.1 |
hwL2mcChnlGroupCfgEntryAn entry of channel is created for each VLAN or VSI in the device create an channel. HWL2mcChnlGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.15.1.1 |
hwChnlGroupCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN.
If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.1 |
hwChnlGroupCfgVsiNameThe name of a VSI.
If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.2 |
hwChnlCfgGroupChnlNameThe channel name. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.3 |
hwChnlGroupCfgGroupAddressThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.4 |
hwChnlGroupCfgGroupLenThe mask length of a multicast group. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.5 |
hwChnlGroupCfgSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.6 |
hwChnlGroupCfgSourceLenThe mask length of a multicast source address. Integer32(0|8..32) .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.7 |
hwChnlGroupCfgPerBandThe bandwidth of a multicast group.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.9 |
hwChnlGroupCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.15.1.1.100 |
hwL2mcGroupPolicyCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.16 |
hwL2mcGroupPolicyCfgTableIn this table, you can query or configure a group policy to filter entries on a port. SEQUENCE OF HWL2mcGroupPolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.16.1 |
hwL2mcGroupPolicyCfgEntryAn entry is created for each active VLAN or VSI in the device when a group policy added. HWL2mcGroupPolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.16.1.1 |
hwGroupPolicyVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.16.1.1.1 |
hwGroupPolicyVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.16.1.1.2 |
hwGroupPolicyAclNumThe number of a basic ACL.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that the value is invalid.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.16.1.1.3 |
hwGroupPolicyIgmpVersionThe IGMP version.
The value ranges from 1 to 4.
The default is 4, indicating that no version is specified.rw Enumeration .1.3.6.1.4.1.2011.5.25.181.1.16.1.1.4 |
hwGroupPolicyRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.16.1.1.100 |
hwL2mcChnlDenyCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.17 |
hwL2mcChnlDenyCfgTableThis table describes the configurations of deny unspecified group for each VLAN or VSI, or in global. SEQUENCE OF HWL2mcChnlDenyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.17.1 |
hwL2mcChnlDenyCfgEntryAn entry of channel deny is created for each VLAN or VSI in the device create an channel. HWL2mcChnlDenyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.17.1.1 |
hwChnlDenyCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN.
If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.17.1.1.1 |
hwChnlDenyCfgVsiNameThe name of a VSI.
If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.17.1.1.2 |
hwChnlDenyCfgWhether discard unspecified channel:
1: not discard
2: discardrw Enumeration .1.3.6.1.4.1.2011.5.25.181.1.17.1.1.3 |
hwChnlDenyCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.17.1.1.100 |
hwL2mcQinQPortInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.18 |
hwL2mcQinQPortTableThis table describes the specific port statistic of QinQ table of protol. SEQUENCE OF HWL2mcQinQPortEntry .1.3.6.1.4.1.2011.5.25.181.1.18.1 |
hwL2mcQinQPortEntryAn entry of the specific port statistic of QinQ table of protol. HWL2mcQinQPortEntry .1.3.6.1.4.1.2011.5.25.181.1.18.1.1 |
hwQinQPortVlanIndexThe VLAN ID, which is the configuration index in a VLAN.
If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.1 |
hwQinQPortVsiNameThe name of a VSI.
If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.2 |
hwL2mcQinQPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.3 |
hwQinQPortGroupAddrThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.4 |
hwQinQPortSourceAddrThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.5 |
hwQinQPortPeThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.6 |
hwQinQPortCeThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.7 |
hwQinQPortTimeThe number of QinQ Port entry live time in second.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.20 |
hwQinQPortFlagThe port flag:
1 static
2 dynamic
3 static and dynamic
4 invalidro Integer32 .1.3.6.1.4.1.2011.5.25.181.1.18.1.1.21 |
hwL2mcETrackingInfoInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.19 |
hwL2mcETrackingInfoTableThis table describes the host explicit tracking. SEQUENCE OF HWL2mcETrackingInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.19.1 |
hwL2mcETrackingInfoEntryAn entry of the host explicit tracking. HWL2mcETrackingInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.19.1.1 |
hwETrackInfoSlotIndexThe slot index, which is interface board number. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.1 |
hwETrackInfoVlanIndexThe VLAN ID, which is the configuration index in a VLAN.
If a VSI is specified, the value is 4095. If both hwETrackInfoVlanIndex and hwETrackInfoVsiName are invalid, the configuration is global.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.2 |
hwETrackInfoVsiNameThe name of a VSI.
If a VLAN is specified, the value is 32. If both hwETrackInfoVlanIndex and hwETrackInfoVsiName are invalid, the configuration is global. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.3 |
hwETrackInfoGroupAddrThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.4 |
hwETrackInfoSourceAddrThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.5 |
hwETrackInfoPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.6 |
hwETrackInfoPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.7 |
hwETrackInfoPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.8 |
hwETrackInfoPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.9 |
hwETrackInfoPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.10 |
hwETrackInfoVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.11 |
hwETrackInfoBoardNumThe interface board number. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.12 |
hwETrackInfoReportAddrThe source IP address of a user. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.13 |
hwETrackInfoFlagThe port filter mode:
1 include
2 excludero Integer32 .1.3.6.1.4.1.2011.5.25.181.1.19.1.1.20 |
hwL2mcSourceGroupInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.22 |
hwL2mcSourceGroupTableTable contains VLAN or VSI performance statistics information
for IGMP Snooping. SEQUENCE OF HWL2mcSourceGroupEntry .1.3.6.1.4.1.2011.5.25.181.1.22.1 |
hwL2mcSourceGroupEntryAn entry is created for each active VLAN or VSI in the device
and deleted when the VLAN or VSI becomes inactive. HWL2mcSourceGroupEntry .1.3.6.1.4.1.2011.5.25.181.1.22.1.1 |
hwL2mcSourceGroupVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.22.1.1.1 |
hwL2mcSourceGroupVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.22.1.1.2 |
hwL2mcSourceGroupGroupAddressThe group address of a multicast group.
In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.22.1.1.3 |
hwL2mcSourceGroupSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.22.1.1.4 |
hwL2mcSourceGroupStatthe packet statistic of (S,G) group.ro Counter64 .1.3.6.1.4.1.2011.5.25.181.1.22.1.1.10 |
hwL2mcDTFwdInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.23 |
hwL2mcDTFwdTableTable contains l2 multicast forward information
for IGMP Snooping. SEQUENCE OF HWL2mcDTFwdEntry .1.3.6.1.4.1.2011.5.25.181.1.23.1 |
hwL2mcDTFwdEntryAn entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when
a forwarding table entry deleted. HWL2mcDTFwdEntry .1.3.6.1.4.1.2011.5.25.181.1.23.1.1 |
hwL2mcDTFwdSlotIndexThe slot index, which is interface board number. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.1 |
hwL2mcDTFwdVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.2 |
hwL2mcDTFwdVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.3 |
hwL2mcDTFwdGroupAddressThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.4 |
hwL2mcDTFwdSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.5 |
hwL2mcDTFwdPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.6 |
hwL2mcDTFwdPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.7 |
hwL2mcDTFwdPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.8 |
hwL2mcDTFwdPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.9 |
hwL2mcDTFwdPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.10 |
hwL2mcDTFwdVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.11 |
hwL2mcDTFwdBoardNumThe interface board number. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.12 |
hwL2mcDTFwdAddressTypeThe address type of an entry:
1: IP
2: MAC
The default value is 1.ro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.21 |
hwL2mcDTFwdHostFlag1The mode to create an interface on the host:
1: static
2: dynamic
3: static and dynamic
4: invalidro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.22 |
hwL2mcDTFwdHostFlag2Whether an interface on the host is created through SSM-mapping:
1: non-mapping
2: mappingro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.23 |
hwL2mcDTFwdHostFlag3The type of an interface created on a router:
1: Interface connected to the host
2: Router interface that replicates multicast data flowsro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.24 |
hwL2mcDTFwdHostFlag4Indicates (S, G) table created :
1: from port;
2: from static;
3: from both
the default falue is 1ro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.23.1.1.25 |
hwL2mcDTGroupInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.24 |
hwL2mcDTGroupInfoTableTable contains l2 multicast group information
for IGMP Snooping. SEQUENCE OF HWL2mcDTGroupInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.24.1 |
hwL2mcDTGroupInfoEntryAn entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when
a forwarding table entry deleted. HWL2mcDTGroupInfoEntry .1.3.6.1.4.1.2011.5.25.181.1.24.1.1 |
hwL2mcDTGroupSlotIndexThe slot index, which is interface board number. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.1 |
hwL2mcDTGroupVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.2 |
hwL2mcDTGroupVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.3 |
hwL2mcDTGroupGroupAddressThe IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.4 |
hwL2mcDTGroupSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.5 |
hwL2mcDTGroupFilterFlagThe filtering mode:
1: include
2: exclude
3: invalid Enumeration .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.6 |
hwL2mcDTPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.7 |
hwL2mcDTGroupPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.8 |
hwL2mcDTGroupPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.9 |
hwL2mcDTGroupPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.10 |
hwL2mcDTGroupPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.11 |
hwL2mcDTGroupVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.12 |
hwL2mcDTGroupBoardNumThe interface board number. Integer32 .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.13 |
hwL2mcDTSourceUpTimeHow long the source group exists in the forwarding entry.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.21 |
hwL2mcDTSourceExpiresThe timeout period of the source group in the forwarding entry, that is, the aging time of the source group.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.22 |
hwL2mcDTGroupUpTimeHow long the group exists in the forwarding entry.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.23 |
hwL2mcDTGroupExpiresWhen the group expires in the forwarding entry, that is, the aging time of the source group.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.24 |
hwL2mcDTGroupHostFlag1The mode to create an interface on the host:
1: static
2: dynamic
3: static and dynamic
4: invalidro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.26 |
hwL2mcDTGroupHostFlag2Whether an interface on the host is created through SSM-mapping:
1: non-mapping
2: mappingro Enumeration .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.27 |
hwL2mcDTGroupRowStatusThe row status.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.24.1.1.100 |
hwL2mcMulticastTrafficPolicyCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.25 |
hwL2mcMulticastTrafficPolicyCfgTableIn this table, you can query or configure whether to disable receive multicast traffic on a port. SEQUENCE OF HWL2mcMulticastTrafficPolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.25.1 |
hwL2mcMulticastTrafficPolicyCfgEntryAn entry is created for each active VLAN or VSI in the device when disable receive multicast traffic on a port. HWL2mcMulticastTrafficPolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.25.1.1 |
hwMulticastTrafficPolicyPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.1 |
hwMulticastTrafficPolicyPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.2 |
hwMulticastTrafficPolicyPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.3 |
hwMulticastTrafficPolicyPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.4 |
hwMulticastTrafficPolicyPortEndCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.5 |
hwMulticastTrafficPolicyPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.6 |
hwMulticastTrafficPolicyVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.7 |
hwMulticastTrafficPolicyVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.8 |
hwMulticastTrafficPolicyEndVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.9 |
hwMulticastTrafficPolicyVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.10 |
hwMulticastTrafficPolicyRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.25.1.1.100 |
hwL2mcRouteLearnDisablePolicyCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.26 |
hwL2mcRouteLearnDisablePolicyCfgTableIn this table, you can query or configure whether to disable router port learning on a port. SEQUENCE OF HWL2mcRouteLearnDisablePolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.26.1 |
hwL2mcRouteLearnDisablePolicyCfgEntryAn entry is created for each active VLAN or VSI in the device when disable router port learning on a port. HWL2mcRouteLearnDisablePolicyCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.26.1.1 |
hwRouteLearnDisablePolicyPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.1 |
hwRouteLearnDisablePolicyPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.2 |
hwRouteLearnDisablePolicyPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.3 |
hwRouteLearnDisablePolicyPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.4 |
hwRouteLearnDisablePolicyPortEndCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.5 |
hwRouteLearnDisablePolicyPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.6 |
hwRouteLearnDisablePolicyVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.7 |
hwRouteLearnDisablePolicyVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.8 |
hwRouteLearnDisablePolicyEndVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.9 |
hwRouteLearnDisablePolicyVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.10 |
hwRouteLearnDisablePolicyRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.26.1.1.100 |
hwL2mcTrackVRRPCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.27 |
hwL2mcTrackVRRPCfgTableIn this table, you can query or configure a port to track VRRP. SEQUENCE OF HWL2mcTrackVRRPCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.27.1 |
hwL2mcTrackVRRPCfgEntryAn entry is created for each active VLAN or VSI in the device when configure a port to track VRRP. HWL2mcTrackVRRPCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.27.1.1 |
hwTrackVRRPPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.1 |
hwTrackVRRPPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.2 |
hwTrackVRRPPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.3 |
hwTrackVRRPPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.4 |
hwTrackVRRPPortEndCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.5 |
hwTrackVRRPVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.6 |
hwTrackVRRPEndVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.7 |
hwTrackVRRPVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.8 |
hwTrackVRRPVridIfIndexThe interface index. The value 0 indicates that the interface index is invalid.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.9 |
hwTrackVRRPVridIDThe VRRP VRID.rw Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.10 |
hwTrackVRRPRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.27.1.1.100 |
hwL2mcMInstCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.28 |
hwL2mcMInstCfgTableThis table create or modified multicast Instance. SEQUENCE OF HWL2mcMInstCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.28.1 |
hwL2mcMInstCfgEntryAn entry of multicast-instance is created in the device. HWL2mcMInstCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.28.1.1 |
hwL2mcMInstIdL2 multicast instance ID Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.28.1.1.1 |
hwL2mcMInstVlanIndexMulticast-VLAN IDrw VlanIdOrAnyOrNone .1.3.6.1.4.1.2011.5.25.181.1.28.1.1.2 |
hwL2mcMInstVsiNameMulticast-VSI namerw DisplayString .1.3.6.1.4.1.2011.5.25.181.1.28.1.1.3 |
hwL2mcMInstProtectInstL2 multicast protect instance IDrw Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.28.1.1.4 |
hwL2mcMInstRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.28.1.1.100 |
hwL2mcMInstGroupCfgTableThist table configure multicast instance mulitcast group infomation. SEQUENCE OF HWL2mcMInstGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.28.2 |
hwL2mcMInstGroupCfgEntryAn entry of multicast-instance channel-group is created in the device. HWL2mcMInstGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.28.2.1 |
hwL2mcMInstGroupIdL2 multicast instance ID Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.28.2.1.1 |
hwL2mcMInstGroupAddressGroup address. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.28.2.1.2 |
hwL2mcMinstGroupAddressMaskGroup address. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.28.2.1.3 |
hwL2mcMInstGroupRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.28.2.1.100 |
hwL2mcMInstUserCfgTableUser instance in the multicast instance. SEQUENCE OF HWL2mcMInstUserCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.28.3 |
hwL2mcMInstUserCfgEntryAn entry of user-instance is created in the device. HWL2mcMInstUserCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.28.3.1 |
hwL2mcMInstUserMInstIdL2 multicast instance ID Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.28.3.1.1 |
hwL2mcMInstUserVLANIDUser VLAN ID. VlanIdOrAnyOrNone .1.3.6.1.4.1.2011.5.25.181.1.28.3.1.2 |
hwL2mcMInstUserEndVLANIDUser End VLAN ID. VlanIdOrAnyOrNone .1.3.6.1.4.1.2011.5.25.181.1.28.3.1.3 |
hwL2mcMInstUserVSINameVSI name. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.28.3.1.4 |
hwL2mcMInstUserRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.28.3.1.100 |
hwL2mcStaticGroupCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.29 |
hwL2mcStaticGroupCfgTableTable contains l2 multicast static group information
for IGMP Snooping. SEQUENCE OF HWL2mcStaticGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.29.1 |
hwL2mcStaticGroupCfgEntryAn entry is created for each active VLAN or VSI in the device create a static group entry and delete when
a static group entry deleted. HWL2mcStaticGroupCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.29.1.1 |
hwStaticGroupCfgPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.1 |
hwStaticGroupCfgPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.2 |
hwStaticGroupCfgPortPeIdThe begin of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.3 |
hwStaticGroupCfgPortPeIdEndThe end of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.4 |
hwStaticGroupCfgPortCeIdThe begin of a CE VID batch.
The value ranges from 1 to 4095.
The value 0 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.5 |
hwStaticGroupCfgPortCeIdEndThe end of a CE VID batch.
The value ranges from 1 to 4095.
The value 0 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.6 |
hwStaticGroupCfgPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.7 |
hwStaticGroupCfgVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.8 |
hwStaticGroupCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.9 |
hwStaticGroupCfgVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.10 |
hwStaticGroupCfgGroupAddressThe group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.11 |
hwStaticGroupCfgSourceAddressThe source IP address of a multicast group. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.12 |
hwStaticGroupCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.29.1.1.100 |
hwL2mcPortGroupPolicyBatchCfgInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.30 |
hwL2mcPortGroupPolicyBatchCfgTableIn this table, you can query or configure a group policy to filter entries on a port. SEQUENCE OF HWL2mcPortGroupPolicyBatchCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.30.1 |
hwL2mcPortGroupPolicyBatchCfgEntryAn entry is created for each active VLAN or VSI in the device when a group policy added. HWL2mcPortGroupPolicyBatchCfgEntry .1.3.6.1.4.1.2011.5.25.181.1.30.1.1 |
hwPortGroupPolicyCfgPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.1 |
hwPortGroupPolicyCfgPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.2 |
hwPortGroupPolicyCfgPortPeIdThe begin of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.3 |
hwPortGroupPolicyCfgPortPeIdEndThe end of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.4 |
hwPortGroupPolicyCfgPortCeIdThe begin of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.5 |
hwPortGroupPolicyCfgPortCeIdEndThe end of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.6 |
hwPortGroupPolicyCfgPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.7 |
hwPortGroupPolicyCfgVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.8 |
hwPortGroupPolicyCfgVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.9 |
hwPortGroupPolicyCfgVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.10 |
hwPortGroupPolicyCfgAclNumThe number of a basic ACL.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that the value is invalid.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.11 |
hwPortGroupPolicyCfgIgmpVersionThe IGMP version.
The value ranges from 0 to 3.
The default is 0, indicating that no version is specified.rw Enumeration .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.12 |
hwPortGroupPolicyCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.30.1.1.100 |
hwL2mcCACPortLimitInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.31 |
hwL2mcCACPortLimitTableThis table describes the configurations of IGMP snooping CAC on an interface. SEQUENCE OF HWL2mcCACPortLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.31.1 |
hwL2mcCACPortLimitEntryAn entry is created for each IGMP snooping CAC on an interface. HWL2mcCACPortLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.31.1.1 |
hwCACPortLimitVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.1 |
hwCACPortLimitVsiNameThe name of a VSI. If a VLAN is specified, the value is 32. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.2 |
hwCACPortLimitPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Port
11: Main-interface-bound-to-vsi HWPortType .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.3 |
hwCACPortLimitIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.4 |
hwCACPortLimitPeIdThe begin of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.5 |
hwCACPortLimitPeIdEndThe end of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.6 |
hwCACPortLimitCeIdThe begin of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.7 |
hwCACPortLimitCeIdEndThe end of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.8 |
hwCACPortLimitPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid. IpAddress .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.9 |
hwCACPortLimitVcOrSiteIdThe VC ID or SITE ID of a PW interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.10 |
hwCACPortLimitChnlNameThe channel name. DisplayString .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.11 |
hwCACPortLimitAclThe number of ACL for the multicast groups that do not need to be configured with CAC limit.
The ACL number ranges from 2000 to 3999.
The default value is 0, indicating that the number is invalid.rw Integer32(0|2000..3999) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.12 |
hwCACPortLimitMaxEntryThe maximum number of forwarding entries. The value 0 indicates that the number is invalid.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.13 |
hwCACPortLimitEntryCntThe number of current forwarding entries.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.14 |
hwCACPortLimitMaxBandWidthThe maximum bandwidth. The value 0 indicates that the bandwidth is invalid.rw Integer32 .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.15 |
hwCACPortLimitBandWidthThe current bandwidth.ro Counter32 .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.16 |
hwCACPortLimitCfgRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.31.1.1.100 |
hwL2mcQinqGroupSourceLimitInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.32 |
hwL2mcQinqGroupLimitTableThis table describes the configurations of IGMP snooping group limit on a QinQ interface. SEQUENCE OF HWL2mcQinqGroupLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.32.1 |
hwL2mcQinqGroupLimitEntryAn entry is created for each IGMP snooping group limit on a QinQ interface. HWL2mcQinqGroupLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.32.1.1 |
hwL2mcQinqGroupLimitPortTypeThe interface type:
1: Invalid
5: Termination sub-interface HWPortType .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.1 |
hwL2mcQinqGroupLimitIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.2 |
hwL2mcQinqGroupLimitPeVidThe begin of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.3 |
hwL2mcQinqGroupLimitPeVidEndThe end of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.4 |
hwL2mcQinqGroupLimitCeVidThe begin of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.5 |
hwL2mcQinqGroupLimitCeVidEndThe end of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.6 |
hwL2mcQinqGroupLimitNumThe group limit number of a QinQ interface.rw Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.10 |
hwL2mcQinqGroupLimitRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.32.1.1.100 |
hwL2mcQinqSourceLimitTableThis table describes the configurations of IGMP snooping source limit on a QinQ interface. SEQUENCE OF HWL2mcQinqSourceLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.32.2 |
hwL2mcQinqSourceLimitEntryAn entry is created for each IGMP snooping source limit on a QinQ interface. HWL2mcQinqSourceLimitEntry .1.3.6.1.4.1.2011.5.25.181.1.32.2.1 |
hwL2mcQinqSourceLimitPortTypeThe interface type:
1: Invalid
5: Termination sub-interface HWPortType .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.1 |
hwL2mcQinqSourceLimitIfIndexThe interface index. The value 0 indicates that the interface index is invalid. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.2 |
hwL2mcQinqSourceLimitPeVidThe begin of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.3 |
hwL2mcQinqSourceLimitPeVidEndThe end of a PE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.4 |
hwL2mcQinqSourceLimitCeVidThe begin of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.5 |
hwL2mcQinqSourceLimitCeVidEndThe end of a CE VID batch.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid. VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.6 |
hwL2mcQinqSourceLimitNumThe source number of a QinQ interface.rw Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.10 |
hwL2mcQinqSourceLimitRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.181.1.32.2.1.100 |
hwL2mcGeneralNotificationsObject OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.33 |
hwL2mcNotificationsPortVlanIndexThe VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095.
The value ranges from 1 to 4095.ro VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.33.1 |
hwL2mcNotificationsPortVsiNameThe name of a VSI. If a VLAN is specified, the value is 32.ro DisplayString .1.3.6.1.4.1.2011.5.25.181.1.33.2 |
hwL2mcNotificationsPortTypeThe interface type:
1: Invalid
2: PW interface
3: L2 interface
4: Encapsulation sub-interface
5: Termination sub-interface
6: Interface Board
7: Vlanif Portro HWPortType .1.3.6.1.4.1.2011.5.25.181.1.33.3 |
hwL2mcNotificationsPortIfIndexThe interface index. The value 0 indicates that the interface index is invalid.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.181.1.33.4 |
hwL2mcNotificationsPortPeIdThe PE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the PE VID is invalid.ro VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.33.5 |
hwL2mcNotificationsPortCeIdThe CE VID of an interface.
The value ranges from 1 to 4095.
The value 4095 indicates that the CE VID is invalid.ro VlanIdOrAny (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.181.1.33.6 |
hwL2mcNotificationsPortPeerAddressThe peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid.ro IpAddress .1.3.6.1.4.1.2011.5.25.181.1.33.7 |
hwL2mcNotificationsPortVcOrSiteIdThe VC ID or SITE ID of a PW interface.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.181.1.33.8 |
hwL2mcNotificationsPortIfNameThe name of the interface.ro DisplayString .1.3.6.1.4.1.2011.5.25.181.1.33.9 |
hwL2mcGeneralNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.1.34 |
hwL2mcPortOtherQuerierTimeoutA hwL2mcPortOtherQuerierTimeout notification signifies the timer of other querier of port is timeout.
This notification should be generated when the other querier timer expires, and the router
has no other querier on the same interface with the same IP version. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.181.1.34.1 |
hwL2mcMibConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.100 |
hwL2mcMibCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.100.1 |
hwL2mcMibGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.181.100.2 |