HUAWEI-L2IF-MIB
AI MIB Summary
The HUAWEI-L2IF-MIB enables monitoring and management of Layer 2 interface states, port operational modes, and configuration parameters for hybrid and trunk ports on Huawei network devices. It provides specific counters and status indicators for Ethernet interface traffic, error statistics, and VLAN tagging behavior to facilitate granular Layer 2 troubleshooting and policy enforcement.
information of layer2 interface and information of hybrid port and information of trunk port
Main OID:
hwL2IfMib.1.3.6.1.4.1.2011.5.25.42.1
117
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
117 total| Object Name |
|---|
hwL2Mgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.42 |
hwL2IfMibinformation of layer2 interface and information of hybrid port and
information of trunk port MODULE-IDENTITY .1.3.6.1.4.1.2011.5.25.42.1 |
hwL2IfObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.42.1.1 |
hwL2Interface OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.42.1.1.1 |
hwL2IfPortMaxMax ports that this device supports,BRIDGE-MIB have a resemble definition.ro Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.1 |
hwL2TopologyDetectWhether to enable layer2 topology detection.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.2 |
hwL2IfTableThis is a table of layer2 interface,so it displays some attribute of
layer2 interface. SEQUENCE OF HwL2IfEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.3 |
hwL2IfEntryEntries of extended Huawei private interface information table HwL2IfEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1 |
hwL2IfPortNumNumber of layer2 interface port, a unique value,
for each port.It is recommended that values are assigned
contiguously starting from 1. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.1 |
hwL2IfPortIfIndexA unique value, greater than zero, for each interface or interface
sub-layer in the managed system. The value is consistent with the
ifIndex in ifTable of IF-MIB.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.2 |
hwL2IfPortTypeLayer2 interface Port type, it contains invalid(0), trunk(1),
access(2), hybrid(3), fabric(4), qinq(5), desirable(6)
and auto(7).Do not support fabric(4) now.
invalid(0),which we read only,can't modify.rw Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.3 |
hwL2IfPVIDLayer2 interface Port VLAN IDrw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.4 |
hwL2IfIsSrcMacFilterWhether to filter source MAC address. We don't support it now.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.5 |
hwL2IfMacAddrLearnModeStatus indicates mac address learn mode of the interface.
IVL(1) means independent VLAN learning.SVL means shared VLAN learning.
We only support iVL now.ro Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.6 |
hwL2IfMacAddressLearnStatus indicates if the interface is allowed to learn mac
address, enable(1) can be setted, (enabled(1) means that
the interface can learn mac address), otherwise disabled(2)
can be setted. discard(3) means the interface will drop packets.rw Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.7 |
hwL2IfBcastRatioBroadcast-suppression ratio. Default is 100% . 100% indicates
that the broadcast isn't suppressed.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.8 |
hwL2IfMcastRatioMulticast-suppression ratio.Default is 100%, 100% indicates that
the multicast isn't suppressed.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.9 |
hwL2IfUcastRatioUnicastsuppression ratio. Default is 100% , 100% indicates that
the broadcast isn't suppressed.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.10 |
hwL2IfOutBcastRatioOutbound broadcast-suppression ratio. Default is 100% . 100% indicates
that the broadcast isn't suppressed.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.11 |
hwL2IfOutMcastRatioOutbound multicast-suppression ratio.Default is 100%, 100% indicates that
the multicast isn't suppressed.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.12 |
hwL2IfOutUcastRatioOutbound unicastsuppression ratio. Default is 100% , 100% indicates that
the broadcast isn't suppressed.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.13 |
hwL2IfDiscardBcastThe flag of droping the broadcast packets,
1:discard; 2:forward(default).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.14 |
hwL2IfDiscardUnknownMcastThe flag of droping the unknown mutilcast packets,
1:discard; 2:forward(default).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.15 |
hwL2IfDiscardUnknownUcastThe flag of droping the unknown unicast packets,
1:discard; 2:forward(default).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.16 |
hwL2IfBpduBpdu enable in port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.17 |
hwL2IfPortPriorityPort priority about interface.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.18 |
hwL2IfPortNameThe interface name.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.19 |
hwL2IfInInvalidVlanPktsThe number of invalid VLAN packets.ro Counter64 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.20 |
hwL2IfFlushEnableThe flush enable status of layer2 port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.21 |
hwL2IfFlushControlVlanThe control vlan of flush packet.rw Integer32 (1..4094 | 65535) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.22 |
hwL2IfCurrentInBcastPercentThe flag of qinq port trust default priority,
1:enable; 2:disable(default).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.23 |
hwL2IfCurrentOutBcastPercentThe flag of port offline status,
1:enable; 2:disable(default).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.24 |
hwL2IfQinqVlanTransEnableEnable QinQ VLAN translation,
1:enable; 2:disable(default).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.25 |
hwL2IfQinqVlanTransMissDropPackets are dropped when a VLAN translation miss occurs,
1:noDrop(default); 2:drop.rw Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.26 |
hwL2IfIpSubnetVlanEnableEnable VLAN assignment based on ip subnet,
1:enable(default); 2:disable.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.27 |
hwL2IfMacVlanEnableMac Vlan enable,
1:enable; 2:disable(default)rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.28 |
hwL2IfPolicyVlanEnablePolicy Vlan enable,
1:enable; 2:disable(default)rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.29 |
hwL2IfVlanPrecedenceDetermine the priorities for selecting VLAN (MAC-based, subnet-based VLANs),
0:MAC VLAN(default); 1:IPSUBNET VLAN.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.30 |
hwL2IfIsolateGroupEnableThe value enabled(1) indicates that the port is a member of the port-isolate group; disable(2) indicates that the port is not a member of the port-isolate group. The default value is disable(2).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.31 |
hwL2IfActivePortTypeLayer2 interface active port type, it contains invalid(0), trunk(1),
access(2), hybrid(3), fabric(4), qinq(5).Do not support fabric(4) now.ro Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.3.1.32 |
hwL2IfHybridPortTableHybrid-port configuration table SEQUENCE OF HwL2IfHybridPortEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.9 |
hwL2IfHybridPortEntryEntry of Hybrid-port configuration table HwL2IfHybridPortEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1 |
hwL2IfHybridPortIndexIndex of Hybrid-port Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.1 |
hwL2IfHybridTaggedVlanListLowThe lowest possible value of the tagged vlan list on the
Hybrid-port.rw VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.2 |
hwL2IfHybridTaggedVlanListHighThe highest possible value of the tagged vlan list on the
Hybrid-port.rw VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.3 |
hwL2IfHybridUnTaggedVlanListLowThe lowest possible value of the untagged vlan list on the
Hybrid-port.rw VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.4 |
hwL2IfHybridUnTaggedVlanListHighThe highest possible value of the untagged vlan list on the
Hybrid-port.rw VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.9.1.5 |
hwL2IfTrunkPortTableTrunk-port configuration table. Trunk-port is a logistic port. SEQUENCE OF HwL2IfTrunkPortEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.10 |
hwL2IfTrunkPortEntryEntry of Trunk-port configuration table HwL2IfTrunkPortEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1 |
hwL2IfTrunkPortIndexIndex of Trunk-port Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1.1 |
hwL2IfTrunkAllowPassVlanListLowThe lowest possible value of the Vlan list that port Trunk allows
to pass.rw VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1.2 |
hwL2IfTrunkAllowPassVlanListHighThe highest possible value of the Vlan list that port Trunk
allows to pass.rw VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.10.1.3 |
hwL2IfPortIsolateTablePort isolate in the same Service-instance table. The Service-instance
is used to communicate among different vlans. SEQUENCE OF HwL2IfPortIsolateEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.11 |
hwL2IfPortIsolateEntryEntry of port isolate configuration table. HwL2IfPortIsolateEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.11.1 |
hwL2IfPortIsolatePortIndexThe port index of L2 interface. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.11.1.1 |
hwL2IfPortIsolateSINameThe name of Service-instance.The Service-instance(S.I.)is used to
communicate among different vlans. OCTET STRING .1.3.6.1.4.1.2011.5.25.42.1.1.1.11.1.2 |
hwL2IfPortIsolateRowStatusThe RowStatus of hwL2IfPortIsolateTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.42.1.1.1.11.1.3 |
hwL2IfSuppressionTablePort suppression configuration table SEQUENCE OF HwL2IfSuppressionEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.12 |
hwL2IfSuppressionEntryEntry of port suppression configuration table HwL2IfSuppressionEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1 |
hwL2IfSuppressionPortIndexThe port index of L2 interface. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.1 |
hwL2IfSuppressionTypeType of port suppression command, a unique value from 1 to 3:
1 means broadcast suppression;
2 means multicast suppression;
3 means unicast suppression. Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.2 |
hwL2IfSuppressionCirCommitted Information Rate. Unit: kbps.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.3 |
hwL2IfSuppressionCbsCommitted Burst Size. Unit: byterw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.4 |
hwL2IfSuppressionRowStatusThe RowStatus of hwL2IfSuppressionTable
.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.42.1.1.1.12.1.5 |
hwL2IfVlanSuppressionTablePort and Vlan suppression configuration table SEQUENCE OF HwL2IfVlanSuppressionEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.13 |
hwL2IfVlanSuppressionEntryEntry of port and Vlan suppression configuration table HwL2IfVlanSuppressionEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1 |
hwL2IfVlanSuppressionPortIndexThe port index of L2 interface. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.1 |
hwL2IfVlanSuppressionStartVlanThe start vlan-id of port and vlan suppression. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.2 |
hwL2IfVlanSuppressionEndVlanThe end vlan-id of port and vlan suppression. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.3 |
hwL2IfVlanSuppressionCirCommitted Information Rate. Unit: kbps.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.4 |
hwL2IfVlanSuppressionCbsCommitted Burst Size. Unit: byterw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.5 |
hwL2IfVlanSuppressionRowStatusThe RowStatus of hwL2IfVlanSuppressionTable
.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.42.1.1.1.13.1.6 |
hwL2IfPortTcnTablePort TCN in the same Service-instance table. The Service-instance
is used to configure TCN. SEQUENCE OF HwL2IfPortTcnEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.14 |
hwL2IfPortTcnEntryEntry of port TCN configuration table. HwL2IfPortTcnEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1 |
hwL2IfTcnPortIndexThe port index of L2 interface. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.1 |
hwL2IfTcnStpStatus indicates if the interface is allowed to notify stp TCN message
, enable(1) can be setted, (enabled(1) means that
the interface can notify TCN), otherwise disabled(2)
can be setted.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.2 |
hwL2IfTcnSmartLinkStatus indicates if the interface is allowed to notify SmartLink TCN message,
enable(1) can be setted, (enabled(1) means that
the interface can notify TCN), otherwise disabled(2)
can be setted.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.3 |
hwL2IfTcnVlanListLowThe lowest possible value of the vlan list on the
Tcn-port.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.4 |
hwL2IfTcnVlanListHighThe highest possible value of the vlan list on the
Tcn-port.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.42.1.1.1.14.1.5 |
hwL2IfPortLoopDetectTableA table containing the port external loopback detection information for device.
It can protect the port from external loopback. SEQUENCE OF HwL2IfPortLoopDetectEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.15 |
hwL2IfPortLoopDetectEntryEntries of the port external loopback detection table. HwL2IfPortLoopDetectEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1 |
hwL2IfPortLoopDetectPortThe port number which will be configured port external loopback detection. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.1 |
hwL2IfPortLoopDetectEnabledWhen this object is set to 'enabled(1)' Port external loopback detection
is enabled on this port else disabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.2 |
hwL2IfPortLoopDetectIntervalThe detect period of port external loopback detection.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.3 |
hwL2IfPortLoopDetectActionThe port external loopback detection protect action of this entry.rw Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.4 |
hwL2IfPortLoopDetectStatusThe current status of port(block/shutdown/trap/normal).ro Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.5 |
hwL2IfPortLoopDetectProtocolThe ethernet type of the detecting packet to port external loopback detection.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.42.1.1.1.15.1.6 |
hwL2IfPortProtocolVlanDataTableThe entry of protocol vlan by port. SEQUENCE OF HwL2IfPortProtocolVlanDataEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.16 |
hwL2IfPortProtocolVlanDataEntryThe entry of protocol vlan by port. HwL2IfPortProtocolVlanDataEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.16.1 |
hwL2IfPortProtocolVlanDataPortIndexThe protocol vlan Index of port . Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.16.1.1 |
hwL2IfPortProtocolVlanDataVlanVLAN ID.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.16.1.2 |
hwL2IfPortProtocolVlanDataPriVLAN PRI.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.16.1.3 |
hwL2IfPortProtocolVlanDataRowStatusOperation status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.42.1.1.1.16.1.4 |
hwL2IfPwSuppressionTablePw suppression configuration table SEQUENCE OF HwL2IfPwSuppressionEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.17 |
hwL2IfPwSuppressionEntryThis object indicates the configuration table for PW-based unknown
traffic suppression. HwL2IfPwSuppressionEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1 |
hwL2IfPwSuppressionVsiNameThis object indicates the name of the VSI that is configured with PW-based
unknown traffic suppression. OCTET STRING .1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.1 |
hwL2IfPwSuppressionPwNameThis object indicates the name of the PW that is configured with PW-based
unknown traffic suppression. OCTET STRING .1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.2 |
hwL2IfPwSuppressionTypeThe value of this object identifies the type of PW-based unknown traffic suppression:
1: broadcast suppression
2: multicast suppression
3: unknown unicast suppression Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.3 |
hwL2IfPwSuppressionCirThis object indicates the Committed Information Rate. Unit: kbit/s.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.4 |
hwL2IfPwSuppressionCbsThis object indicates the Committed Burst Size. Unit: byte.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.5 |
hwL2IfPwSuppressionRowStatusThis object indicates the RowStatus of hwPwSuppressionTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.42.1.1.1.17.1.50 |
hwL2IfLoopDetectIntervalThe detect period of system external loopback detection.rw Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.18 |
hwL2IfDynamicPortVlanTableTable for dynamic relationship of port-vlan. SEQUENCE OF HwL2IfDynamicPortVlanEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.19 |
hwL2IfDynamicPortVlanEntryEntry of dynamic port-vlan relationship table. HwL2IfDynamicPortVlanEntry .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1 |
hwL2IfDynamicPortVlanPortIndexPort index of switch-port. Integer32 .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.1 |
hwL2IfDynamicPortVlanServiceTypeService type of dynamic port-vlan relationship table. Enumeration .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.2 |
hwL2IfDynamicPortVlanPvidThe Dynamic PVID of port-vlan table.ro VlanIdOrNone (Q-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.3 |
hwL2IfDynamicPortVlanUntaggedVlanListLowThe lowest possible value of the untagged vlan list of dynamic port-vlan table.ro VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.4 |
hwL2IfDynamicPortVlanUntaggedVlanListHighThe highest possible value of the untagged vlan list of Dynamic port-vlan table.ro VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.5 |
hwL2IfDynamicPortVlanTaggedVlanListLowThe lowest possible value of the tagged vlan list of Dynamic port-vlan table.ro VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.6 |
hwL2IfDynamicPortVlanTaggedVlanListHighThe highest possible value of the tagged vlan list of Dynamic port-vlan table.ro VlanList .1.3.6.1.4.1.2011.5.25.42.1.1.1.19.1.7 |
hwL2IfTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.42.1.1.2 |
hwL2IfInvalidVlanPacketAlarmWarning of receiving invalid VLAN packets in the interface. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.42.1.1.2.1 |
hwInBcastRisingThresholdPort status changed because loopback detect.(Normal/Block/Shutdown/Trap) NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.42.1.1.2.2 |
hwL2IfConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.42.1.2 |
hwL2IfCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.42.1.2.1 |
hwL2IfGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.42.1.2.2 |