HUAWEI-FLASH-MAN-MIB
AI MIB Summary
The HUAWEI-FLASH-MAN-MIB enables SNMP-based monitoring and control of Huawei device flash storage subsystems, specifically tracking flash card status, capacity utilization, and operation states. This module facilitates the management of flash card insertion, removal, and formatting operations to ensure reliable non-volatile storage availability.
The HUAWEI-FLASH-MIB contains objects to manage the device flash cards and flash card operations. There are no constraints on this MIB.
Main OID:
hwFlash.1.3.6.1.4.1.2011.6.9
101
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
101 total| Object Name |
|---|
hwFlashThe HUAWEI-FLASH-MIB contains objects to manage the device flash cards
and flash card operations. There are no constraints on this MIB. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.9 |
huaweiFlashManMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1 |
huaweiFlashDevice OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1.1 |
hwFlhSupportNumSpecifies the total number of flash which the
system supported.
The MIB should not be loaded if there is no flash
on the device, therefore the value of the object is at least 1.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.1 |
hwFlashTableThis table gives the properties of all the flashes on the device . SEQUENCE OF HwFlashEntry .1.3.6.1.4.1.2011.6.9.1.1.2 |
hwFlashEntryThe entries of hwFlashTable. HwFlashEntry .1.3.6.1.4.1.2011.6.9.1.1.2.1 |
hwFlhIndexThe index of hwFlashTable. It has the minimum value of 1, and
maximum value of the same as the value of hwFlhSupportNum.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.2.1.1 |
hwFlhSizeSpecifies the total size of the Flash device indexed by hwFlhIndex.
The value will be zero if the flash is removed for a removable
device.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.2011.6.9.1.1.2.1.2 |
hwFlhPosThe position of the flash device on the system.This object is
an index of entPhysicalTable in ENTITY-MIB . If the value of this object
is 0, the main processor is indicated.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.2.1.3 |
hwFlhNameThe flash device name used to refer to the
device within the system.ro DisplayString .1.3.6.1.4.1.2011.6.9.1.1.2.1.4 |
hwFlhChipNumThe chip numbers in the flash device.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.2.1.5 |
hwFlhDescrDescription of the purpose of the flash device on the system.ro DisplayString .1.3.6.1.4.1.2011.6.9.1.1.2.1.6 |
hwFlhInitTimeThe system time at which device was initialized.
For fixed devices, this will be the system's boot up time.
For removable devices, it will be the time at which
the device was inserted. It may be a later time if device was inserted later.
If a device can be partitioned and repartitioned,
it will be the time of repartitioning.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.1.2.1.8 |
hwFlhRemovableThe object indicates whether the flash indexed can be removed or not.
The true(1) value indicates the flash device CAN be removed .The false(2) value
indicates the flash device CANNOT be removed .ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.1.2.1.9 |
hwFlhPartitionBoolThe object indicates whether the flash indexed can be partitioned or not.
The true(1) value indicates the flash device CAN be partitioned. The false(2) value
indicates the flash device CANNOT be partitioned.The actual partition state depends
on the value of hwFlhDevicePartions.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.1.2.1.11 |
hwFlhMinPartitionSizeMinimum partition size the device supported.
If hwFlhDevicePartitionBool is false, the value
of this object is the same as hwFlhDeviceSize.ro Integer32 UNITS "bytes" .1.3.6.1.4.1.2011.6.9.1.1.2.1.12 |
hwFlhMaxPartitionsThe maximum count of partitions which the system supports
for this Flash device.If hwFlhPartitionBool is false,
the object value is 1.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.2.1.13 |
hwFlhPartitionNumThe actual number of partitions supported by the system for
this Flash device.If hwFlhPartitionBool is false,
the object value is 1.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.2.1.14 |
hwFlashChips OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1.1.3 |
hwFlhChipTableTable of Flash device chip properties for each
initialized Flash device.
This table is meant primarily for aiding error
diagnosis. SEQUENCE OF HwFlhChipEntry .1.3.6.1.4.1.2011.6.9.1.1.3.1 |
hwFlhChipEntryThe entry of hwFlhChipTable HwFlhChipEntry .1.3.6.1.4.1.2011.6.9.1.1.3.1.1 |
hwFlhChipSerialNoIndex of hwFlhChipTable. Integer32 .1.3.6.1.4.1.2011.6.9.1.1.3.1.1.1 |
hwFlhChipIDThe manufacturer and device code for a chip.
The device code is in the lower byte.And
The manufacturer code is in the Upper byte.
Unknown chip code is presented as 00:00.ro DisplayString .1.3.6.1.4.1.2011.6.9.1.1.3.1.1.2 |
hwFlhChipDescrThe description of the flash chip.
e.g. 'Intel 27F008SA'ro DisplayString .1.3.6.1.4.1.2011.6.9.1.1.3.1.1.3 |
hwFlhChipWriteTimesLimitThe maximum number of write retries done at any
single location before declaring a write failure.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.3.1.1.4 |
hwFlhChipWriteTimesThis object will provide a cumulative count
(since last system boot up or initialization) of
the number of write retries that were done in the chip.
If no writes have been done to Flash, the count
will be zero. Typically, a maximum of 25 retries are
done on a single location before flagging a write
error.
A management station is expected to get this object
for each chip in a partition after a write failure
in that partition. To keep a track of retries for
a given write operation, the management station would
have to retrieve the values for the concerned chips
before and after any write operation.
It is a cumulative count of write retries that were done in the chip.ro Counter32 .1.3.6.1.4.1.2011.6.9.1.1.3.1.1.5 |
hwFlhChipEraseTimesLimitThe maximum number of erase retries done within
an erase sector before declaring an erase failure.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.3.1.1.6 |
hwFlhChipEraseTimesThis object will provide a cumulative count
(since last system boot up or initialization) of
the number of erase retries that were done in the chip.
Typically, a maximum of 2000 retries are done in a
single erase zone (which may be a full chip or a
portion, depending on the chip technology) before
flagging an erase error.
A management station is expected to get this object
for each chip in a partition after an erase failure
in that partition. To keep a track of retries for
a given erase operation, the management station would
have to retrieve the values for the concerned chips
before and after any erase operation.
Note that erase may be done through an independent
command, or through a copy-to-flash command.ro Counter32 .1.3.6.1.4.1.2011.6.9.1.1.3.1.1.7 |
hwFlashPartitions OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1.1.4 |
hwFlhPartitionTableTable of flash device partition properties for each
initialized flash partition. Whenever there is no
explicit partitioning done, a single partition spanning
the entire device will be assumed to exist. There will
therefore always be at least one partition on a device. SEQUENCE OF HwFlhPartitionEntry .1.3.6.1.4.1.2011.6.9.1.1.4.1 |
hwFlhPartitionEntryAn entry in the table of flash partition properties
for each initialized flash partition. Each entry
will be indexed by a device number and a partition
number within the device. HwFlhPartitionEntry .1.3.6.1.4.1.2011.6.9.1.1.4.1.1 |
hwFlhPartIndexThe one of indexes which specifies a partition in system.
It is the sequence number of partitions. Integer32 .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.1 |
hwFlhPartFirstChipThe first chip's sequence number in the
partition, by which a chip can be indexed in
chip table.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.2 |
hwFlhPartLastChipThe last chip's sequence number in the
partition, by which a chip can be indexed in
chip table.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.3 |
hwFlhPartSpaceThe total space of the flash partition.
The following should be satisfied:
hwFlhPartSpace = n*hwFlhMinPartitionSizero Integer32 UNITS "bytes" .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.4 |
hwFlhPartSpaceFreeThe Flash partition's free space.ro Gauge32 UNITS "bytes" .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.5 |
hwFlhPartFileNumThe number of all the file in the flash
partition.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.6 |
hwFlhPartChecksumMethodThe Checksum algorithm identifier
checksum method which the
file system uses.ro Enumeration .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.7 |
hwFlhPartStatusThe flash partition status.
If device is not programmable the value of it will be 'readOnly(1)';
If the current image is running from this partition, the value of it
will be 'runFromFlash(2)';
If device is programmable the value of it will be 'readWrite(3) '.ro HwFlashPartitionStatus .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.8 |
hwFlhPartUpgradeModeThe upgrade method of Flash partition, ie., method by which
new files can be downloaded into the partition.
FLH stands for Flash Load Helper, a feature provided
on run-from-Flash systems for upgrading Flash. This
feature uses the bootstrap code in ROMs to help in
automatic download.
This object should be retrieved if the partition
status is runFromFlash(2).
If the partition status is readOnly(1), the upgrade
method would depend on the reason for the readOnly
status. For eg., it may simply be a matter of installing
the programming jumper, or it may require execution of a
later version of software that supports the Flash chips.
unknown(1) - the current system image does not know
how Flash can be programmed. A possible
method would be to reload the ROM image
and perform the upgrade manually.
rxbootFLH(2) - the Flash Load Helper is available to
download files to Flash. A copy-to-flash
command can be used and this system image
will automatically reload the Rxboot image
in ROM and direct it to carry out the
download request.
direct(3) - will be done directly by this image.ro HwFlashPartitionUpgradeMode .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.9 |
hwFlhPartNameThe name of flash partition.
It was referred by the system.ro DisplayString .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.10 |
hwFlhPartRequireEraseIndicates whether the partition of flash needed
to be erased or not before write operation on it.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.11 |
hwFlhPartFileNameLenThe maximum length of file name in the system.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.4.1.1.12 |
hwFlhFiles OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1.1.4.2 |
huaweiFlhFileTableTable of information for files in a Flash partition. SEQUENCE OF HuaweiFlhFileEntry .1.3.6.1.4.1.2011.6.9.1.1.4.2.1 |
huaweiFlhFileEntryAn entry in the table of Flash file properties
for each initialized Flash partition. Each entry
represents a file and gives details about the file.
An entry is indexed using the device number,
partition number within the device, and file
number within the partition. HuaweiFlhFileEntry .1.3.6.1.4.1.2011.6.9.1.1.4.2.1.1 |
hwFlhFileIndexThe index of the table . Integer32 .1.3.6.1.4.1.2011.6.9.1.1.4.2.1.1.1 |
hwFlhFileNameA valid file name supported by the file system.ro DisplayString .1.3.6.1.4.1.2011.6.9.1.1.4.2.1.1.2 |
hwFlhFileSizeThe file size in bytes, which doesn't include the file header of filesystem.
The minimum value of it will be 1.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.1.4.2.1.1.3 |
hwFlhFileStatusThe status maybe follows:
deleted(1):The file is in recycle.
checksumWrong(2):The checksum of file is invalid;
valid(3):A valid file.ro Enumeration .1.3.6.1.4.1.2011.6.9.1.1.4.2.1.1.4 |
hwFlhFileChecksumThe file checksum located in the header of file.ro OCTET STRING .1.3.6.1.4.1.2011.6.9.1.1.4.2.1.1.5 |
hwFlhFileTimeThe file checksum located in the header of file.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.1.4.2.1.1.6 |
huaweiFlashOperate OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1.2 |
huaweiFlhOpTableA table of Flash copy operation entries. Each
entry represents a Flash copy operation (to or
from Flash) that has been initiated. SEQUENCE OF HuaweiFlhOpEntry .1.3.6.1.4.1.2011.6.9.1.2.1 |
huaweiFlhOpEntryA Flash copy operation entry. Each entry consists
of a command, a source, and optional parameters such
as protocol to be used, a destination, a server address,
etc.
A management station wishing to create an entry should
first generate a pseudo-random serial number to be used
as the index to this sparse table. The station should
then create the associated instance of the row status
object. It must also, either in the same or in successive
PDUs, create the associated instance of the command and
parameter objects. It should also modify the default values
for any of the parameter objects if the defaults are not
appropriate.
Once the appropriate instances of all the command
objects have been created, either by an explicit SNMP
set request or by default, the row status should be set
to active to initiate the operation. Note that this entire
procedure may be initiated via a single set request which
specifies a row status of createAndGo as well as specifies
valid values for the non-defaulted parameter objects.
Once an operation has been activated, it cannot be
stopped.
Once the operation completes, the management station should
retrieve the value of the status object (and time if
desired), and delete the entry. In order to prevent old
entries from clogging the table, entries will be aged out,
but an entry will never be deleted within 5 minutes of
completing. HuaweiFlhOpEntry .1.3.6.1.4.1.2011.6.9.1.2.1.1 |
hwFlhOperIndexSpecifies the index of an entry. It is a
random value when creating an entry. Integer32 .1.3.6.1.4.1.2011.6.9.1.2.1.1.1 |
hwFlhOperTypeSpecifies the operation to be executed.
net2FlashWithErase Copy a file to flash; erase
flash before copy.
Use the FTP protocol or SFTP protocol.
net2FlashWithoutErase Same with net2FlashWithErase.
flash2Net Copy a file from flash using
the FTP protocol or SFTP protocol.
delete delete file or directory by source file name.rw Enumeration .1.3.6.1.4.1.2011.6.9.1.2.1.1.2 |
hwFlhOperProtocolSpecifies the protocol used to transfer file.
The default value of it is ftp. When hwFlhOperProtocol is specified as SFTP, only
password authentication-type is valid.rw Enumeration .1.3.6.1.4.1.2011.6.9.1.2.1.1.3 |
hwFlhOperServerAddressThe address of remote host acting as server for any operation.rw IpAddress .1.3.6.1.4.1.2011.6.9.1.2.1.1.4 |
hwFlhOperServerUserWhen use ftp or sftp to transfer files, the user name must be
specified by this node.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.1.1.5 |
hwFlhOperPasswordRemote user password for copy via ftp protocol. Optional.
This object will be ignored for protocols other than
ftp and sftp.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.1.1.6 |
hwFlhOperSourceFileSpecifies the Source file name to be transferred .
It may be located on flash or remote server.
It may include the file path if it is applicable.
It must be specified.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.1.1.7 |
hwFlhOperDestinationFileSpecifies the destination file name to be transferred .
It may be located on flash or remote server.
It may include the file path if it is applicable.
If it is not specified , the destination file name
is the same as source file name for application.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.1.1.8 |
hwFlhOperStatusThe status of operation.
The status of the specified operation can be one of the follows.
opInProgress(1) : the operation is in process.
opSuccess(2) : the operation has been completed successfully.
opInvalid(3) : the command is invalid or command-protocol-device
combination is unsupported by the system.
opInvalidProtocol(4) :invalid protocol is specified
opInvalidSourceName(5) :invalid source file name is specified.
opInvalidDestName(6) :invalid target name is specified.
opInvalidServerAddress(7) :invalid server address is specified
opDeviceBusy(8) :the device is in use and locked by another process
opDeviceOpenError(9) :invalid device name is specified.
opDeviceError(10) : device read, write or erase error
opDeviceNotProgrammable(11) :device is read-only but a write or erase operation was specified
opDeviceFull(12) : device is filled to capacity
opFileOpenError(13) :invalid file name; file not found in partition
opFileTransferError(14) :file transfer was unsuccessfull
opFileChecksumError(15) :file checksum in Flash si invalid
opNoMemory(16) :system is running in low on memory
opAuthFail(17) :authentication failure
opUnknownFailure(18) :failure which is unknown
opAbort(19) : transfer operation has been aborted
opInvalidSourceAddress(20) : invalid source IP is specified.
opInvalidSourceInterface(21) : invalid source interface is specified.
opCurrentVersionFileConfilt(22) : conflict between target file and system filero HwFlashOperationStatus .1.3.6.1.4.1.2011.6.9.1.2.1.1.9 |
hwFlhOperEndNotificationIf the value of it is specified 'true',a notification
will be generated at the end of the operation.
Otherwise no notification will be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.2.1.1.10 |
hwFlhOperProgressThe progress described as the time taken for
the operation.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.2011.6.9.1.2.1.1.11 |
hwFlhOperRowStatusThe status of this table entry.
When the status is active :
(1) In the situation that the specified transfer operation by
ftp/tftp is in progress, the transfer operation will be aborted
if the status is set to notInService.
(2) In any other situations, the specified operation will not be
aborted even if the status is set to notInService.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.2.1.1.12 |
hwFlhOperServerPortThis object specifies the SFTP/FTP server port that is used for file transfer
only if the value of hwFlhOperProtocol is sftp/ftp.
The default SFTP server port is 22 if no port is specified.
The default FTP server port is 21 if no port is specified.
If the value of hwFlhOperProtocol is not sftp/ftp, this object is ignored by the
implementation.rw Integer32 .1.3.6.1.4.1.2011.6.9.1.2.1.1.13 |
hwFlhOperSourceAddressThe source IP address. When hwFlhOperType is specified as net2FlashWithErase,
net2FlashWithoutErase or flash2Net, the source IP address
of the client may be specified or not. Default is 0.0.0.0 .
If the source type is set to both of IP address and interface,
the former has the priority.rw IpAddress .1.3.6.1.4.1.2011.6.9.1.2.1.1.14 |
hwFlhOperSourceInterfaceThe name of the source interface.When hwFlhOperType is specified as
net2FlashWithErase,net2FlashWithoutErase or flash2Net,the source interface
of the FTP/TFTP client may be specified or not. If the source
type is set to both of IP address and interface,the former has
the priority.rw OCTET STRING .1.3.6.1.4.1.2011.6.9.1.2.1.1.15 |
hwFlhOperMemSizeThis object specifies the reserved space (in KBs) guaranteed by a host.
The value 0 indicates that no space need be reserved. The default value is 0. This
object is optional when hwFlhOperType is specified as net2FlashWithErase or
net2FlashWithoutErase in the Set operation. This object is unavailable when
hwFlhOperType is specified as flash2Net or delete in the Set operation.rw Integer32 .1.3.6.1.4.1.2011.6.9.1.2.1.1.16 |
hwFlhOperVpnInstanceNameThe vpn instance name of the file server.rw OCTET STRING .1.3.6.1.4.1.2011.6.9.1.2.1.1.17 |
hwFlhOperTotalFileLengthThe total length of the file, in bytes.rw Integer32 .1.3.6.1.4.1.2011.6.9.1.2.1.1.18 |
hwFlhOperTransferProgressThe transfer progress of the file.ro Integer32 .1.3.6.1.4.1.2011.6.9.1.2.1.1.19 |
hwFlhOperErrorReasonThe failure reason of operation.ro DisplayString .1.3.6.1.4.1.2011.6.9.1.2.1.1.20 |
hwFlhSyncTableA table of Flash synchronize operate include copy/delete etc. SEQUENCE OF HwFlhSyncEntry .1.3.6.1.4.1.2011.6.9.1.2.2 |
hwFlhSyncEntryA Flash synchronize operation entry. Each entry consists
of a synchronize command, such as copy,delete etc. HwFlhSyncEntry .1.3.6.1.4.1.2011.6.9.1.2.2.1 |
hwFlhSyncIndexSpecifies the index of an entry.
It is a random value when creating an entry. Integer32 .1.3.6.1.4.1.2011.6.9.1.2.2.1.1 |
hwFlhSyncTypeSynchronize operation type to be executed.
net2FlashCopy Net operate copy a file from one board to another;rw Enumeration .1.3.6.1.4.1.2011.6.9.1.2.2.1.2 |
hwFlhSyncRangeSynchronize operation range to be executed.
designate Net designate a object to be handled as synchronize destination;
all Net make all chassis and all board as handled object;rw Enumeration .1.3.6.1.4.1.2011.6.9.1.2.2.1.3 |
hwFlhSyncSourcePathThe source board path to be transferred.
It must be specified.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.2.1.4 |
hwFlhSyncSourceFileThe source file name to be transferred .
It is located on the flash of the mainboard of a chassis.
It is combine with the hwFlhSyncSourcePath to specify the absolute file name.
It must be specified.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.2.1.5 |
hwFlhSyncDestinationPathThe destination board path to be transferred.
It must be specified.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.2.1.6 |
hwFlhSyncDestinationFileThe destination file name to be transferred .
It is combine with the hwFlhSyncDestinationPath to specify the absolute file name.
It must be specified.rw DisplayString .1.3.6.1.4.1.2011.6.9.1.2.2.1.7 |
hwFlhSyncRowStatusThe row status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.2.2.1.8 |
huaweiFlashNotification OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1.3 |
hwFlhOperNotificationA hwFlhOperNotification is sent only when hwFlhOperEndNotification is true. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.9.1.3.1 |
hwFlhSyncSuccessNotificationA hwFlhSyncSuccessNotification is sent when the file copy operation successful. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.9.1.3.2 |
hwFlhSyncFailNotificationA hwFlhSyncFailNotification is sent when the file copy operation failed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.9.1.3.3 |
huaweiStorageDevice OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.1.4 |
hwStorageTableThis table gives the properties of all the storage devices on the device . SEQUENCE OF HwStorageEntry .1.3.6.1.4.1.2011.6.9.1.4.2 |
hwStorageEntryThe entries of hwStorageTable. HwStorageEntry .1.3.6.1.4.1.2011.6.9.1.4.2.1 |
hwStorageIndexThe index of hwStorageTable. It has the minimum value of 1. Integer32 .1.3.6.1.4.1.2011.6.9.1.4.2.1.1 |
hwStorageTypeThe type of all the storage devices on the devicero Enumeration .1.3.6.1.4.1.2011.6.9.1.4.2.1.2 |
hwStorageSpaceSpecifies the total size of the storage devices indexed by hwStorageTable.ro Integer32 UNITS "kbytes" .1.3.6.1.4.1.2011.6.9.1.4.2.1.3 |
hwStorageSpaceFreeThe free space of the storage devices.ro Integer32 UNITS "kbytes" .1.3.6.1.4.1.2011.6.9.1.4.2.1.4 |
hwStorageNameThe storage devices name used to refer to the
device within the system.ro DisplayString .1.3.6.1.4.1.2011.6.9.1.4.2.1.5 |
hwStorageDescrDescription of the purpose of the storage devices on the system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2011.6.9.1.4.2.1.6 |
huaweiFlashMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.2 |
hwFlhMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.2.1 |
huaweiFlashMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.9.2.2 |