HUAWEI-ENT-VOICE-PORT-MIB
AI MIB Summary
The HUAWEI-ENT-VOICE-PORT-MIB module enables the monitoring and management of voice port interfaces on Huawei enterprise networking equipment, exposing specific metrics such as port status, traffic statistics, and call state information for VoIP services.
huawei VOICE PORT mib.
Main OID:
hwEntVoicePortMIB.1.3.6.1.4.1.2011.5.25.252
93
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
93 total| Object Name |
|---|
hwEntVoicePortMIBhuawei VOICE PORT mib. MODULE-IDENTITY .1.3.6.1.4.1.2011.5.25.252 |
hwEntFxsPortConfigTableIndicates the attribute configuration table of fxs ports. SEQUENCE OF HwEntFxsPortConfigEntry .1.3.6.1.4.1.2011.5.25.252.1 |
hwEntFxsPortConfigEntryIndicates the attribute configuration entry of fxs ports. HwEntFxsPortConfigEntry .1.3.6.1.4.1.2011.5.25.252.1.1 |
hwEntFxsPortIndexIndicates the slot/subcard/port index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.1 |
hwEntFxsPortSendGainIndicates the send gain the fxs port.
0: 5 dB
1: 4.5 dB
2: 4 dB
3: 3.5 dB
4: 3 dB
5: 2.5 dB
6: 2 dB
7: 1.5 dB
8: 1 dB
9: 0.5 dB
10: 0 dB
11: -0.5 dB
12: -1 dB
13: -1.5 dB
14: -2 dB
15: -2.5 dB
16: -3 dB
17: -3.5 dB
18: -4 dB
19: -4.5 dB
20: -5 dB
21: -5.5 dB
22: -6 dB
Default: 10rw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.2 |
hwEntFxsPortRecvGainIndicates the receive gain the fxs port.
0: 0 dB
1: -0.5 dB
2: -1 dB
3: -1.5 dB
4: -2 dB
5: -2.5 dB
6: -3 dB
7: -3.5 dB
8: -4 dB
9: -4.5 dB
10: -5 dB
11: -5.5 dB
12: -6 dB
13: -6.5 dB
14: -7 dB
15: -7.5 dB
16: -8 dB
17: -8.5 dB
18: -9 dB
19: -9.5 dB
20: -10 dB
21: -10.5 dB
22: -11 dB
23: -11.5 dB
24: -12 dB
Default: 14rw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.3 |
hwEntFxsPortDialModeIndicates the dialing mode.
Options:
dtmfPulseBoth(1) -DTMF pulse both
dtmfOnly(2) -DTMF only
pulseOnly(3) -Pulse only
Default: dtmfPulseBoth(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.1.1.4 |
hwEntFxsPortReversePoleEnableIndicates whether to support the polarity-reversing pulse.
Options:
enable(1)
disable(2)
Default: enable(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.1.1.5 |
hwEntFxsPortReversePoleLevelIndicates the level width of the polarity-reversing pulse.
Default: 100
Unit: ms
Step: 10 ms.rw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.6 |
hwEntFxsPortPolarityReverseModeIndicates the polarity reversal mode.
Options:
hard(1) -Hard polarity reversal
soft(2) -Soft polarity reversal
Default: hard(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.1.1.7 |
hwEntFxsPortLineLockIndicates whether to support lock port.
enable(1)
disable(2)
Default: enable(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.1.1.8 |
hwEntFxsPortNlpModeIndicates the Nlp mode of the port.
normal(1) -Normal mode
ecGainAdjust(2) -Ec gain adjust mode
enhance(3) -Enhance mode
reduce(4) -Reduce mode
disable(5): -Close mode
Default: normal(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.1.1.9 |
hwEntFxsPortClipReversePoleIndicates whether to support the polarity-reversing pulse when Clip.
enable(1)
disable(2)
Default: disable(2)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.1.1.10 |
hwEntFxsPortImpedanceIndicates the port impedance of the board.
Each value corresponds to the required impedance in a specified scenario.
0: Bureau machine in China (200+680|| 100nf)
1: User machine in China (200+560|| 100nf)
2: 600-ohm interface
3: Interface of Russia (150+510|| 47nf)
4: (220+820|| 115nf )
5: (220+820|| 120nf )
6: 900-ohm interface
7: Interface of Brazil (800|| 50nf)
8: BT0(Zin=87+1052||228nF+229||28.4nF, Zload=93+615||471nF+179||495nF+244||32nF)
9: HK_BT3(Zin=370+620|| 310nf,Zload=600)
10: HK_BT5(Zin=270+264|| 357nf+1434|| 265nf,Zload=600)
11: BT1(BT0 without AGC)
12: BT2(Zin=(87 +1052 //228nF+229 //28.4nF),Zload=(270 +264 //357nF+1434 //265nF))
13: BT3(Zin=(87 +1052 //228nF+229 //28.4nF),Zload=(164 +162 //363nF+1227 //350nF))
14: Commonly used in Europe (Zin= 270+750|| 150nf)
15: New zealand (Zin=370+620|| 310nf)
Default: 2rw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.11 |
hwEntFxsPortCurrentPort current supported by the board. The value ranges from 0 to 1, which indicates the port current value.
0: 16mA steady current
1: 20mA steady current
Default: 1rw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.12 |
hwEntFxsPortHighLevelIndicates the high power level width.
Default: 100
Unit: msrw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.13 |
hwEntFxsPortLowLevelIndicates the low power level width.
Default: 300
Unit: msrw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.14 |
hwEntFxsPortKcTypeIndicates the KC type.
Options:
1. type16kc(1)
2. type12kc(2)
Default: type16kc(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.1.1.15 |
hwEntFxsPortVoltageIndicates the valid voltage value of KC.
0: 0.45 Vrms
1: 0.775 Vrms
2: 1.0 Vrms
3: 1.5 Vrms
4: 2.0 Vrms
5: 2.5 Vrms
6: 3.0 Vrms
7: 3.5 Vrms
8: 4.0 Vrms
9: 4.5 Vrms
Default: 5rw Integer32 .1.3.6.1.4.1.2011.5.25.252.1.1.16 |
hwEntFxsPortActualSendGainIndicates the actual send gain of the fxs port.
0: 5 dB
1: 4.5 dB
2: 4 dB
3: 3.5 dB
4: 3 dB
5: 2.5 dB
6: 2 dB
7: 1.5 dB
8: 1 dB
9: 0.5 dB
10: 0 dB
11: -0.5 dB
12: -1 dB
13: -1.5 dB
14: -2 dB
15: -2.5 dB
16: -3 dB
17: -3.5 dB
18: -4 dB
19: -4.5 dB
20: -5 dB
21: -5.5 dB
22: -6 dB
255: nullro Integer32(0..22|255) .1.3.6.1.4.1.2011.5.25.252.1.1.17 |
hwEntFxsPortActualRecvGainIndicates the actual receive gain of the fxs port.
0: 0 dB
1: -0.5 dB
2: -1 dB
3: -1.5 dB
4: -2 dB
5: -2.5 dB
6: -3 dB
7: -3.5 dB
8: -4 dB
9: -4.5 dB
10: -5 dB
11: -5.5 dB
12: -6 dB
13: -6.5 dB
14: -7 dB
15: -7.5 dB
16: -8 dB
17: -8.5 dB
18: -9 dB
19: -9.5 dB
20: -10 dB
21: -10.5 dB
22: -11 dB
23: -11.5 dB
24: -12 dB
255: nullro Integer32(0..24|255) .1.3.6.1.4.1.2011.5.25.252.1.1.18 |
hwEntFxsPortOperTableIndicates the operation table (management, maintenance, and status query) of the fxs ports. SEQUENCE OF HwEntFxsPortOperEntry .1.3.6.1.4.1.2011.5.25.252.2 |
hwEntFxsPortOperEntryIndicates the operation entry (management, maintenance, and status query) of the fxs ports. HwEntFxsPortOperEntry .1.3.6.1.4.1.2011.5.25.252.2.1 |
hwEntFxsPortOperIndexIndicates the FxsPortOper index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.2.1.1 |
hwEntFxsPortSrvStateIndicates state of the fxs port.
Options:
normal(1)
fault(2)
deactive(3)
powerdeny(4)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.2.1.2 |
hwEntFxsPortAdminStateIndicates admin state of the fxs port.
Options:
noLoopNoTest(1)
noLoopTest(2)
localLoopNoTest(3)
localLoopTest(4)
remoteLoopNoTest(5)
remoteLoopTest(6)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.2.1.3 |
hwEntFxsPortLineStateIndicates line state of the fxs port.
Options:
normal(1)
onEarth(2)
unknown(3)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.2.1.4 |
hwEntFxsPortAdminOperIndicates operation type the fxs port.
Options:
remoteLoop(1)
localLoop(2)
cancelLoop(3)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.2.1.5 |
hwEntBraPortConfigTableIndicates the attribute configuration table of the bra port. SEQUENCE OF HwEntBraPortConfigEntry .1.3.6.1.4.1.2011.5.25.252.3 |
hwEntBraPortConfigEntryIndicates the attribute configuration entry of the bra port. HwEntBraPortConfigEntry .1.3.6.1.4.1.2011.5.25.252.3.1 |
hwEntBraPortIndexIndicates the slot/subcard/port index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.3.1.1 |
hwEntBraPortRemotePowerIndicates whether to support remote power supply.
Options:
enable(1) -Supported
disable(2) -Not supported
Default: disable(2)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.3.1.2 |
hwEntBraPortAutoDeactiveIndicates whether to support automatic deactivation.
Options:
enable(1) -Supported
disable(2) -Not supported
Default: disable(2)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.3.1.3 |
hwEntBraPortAutoDeactiveDelayIndicates the automatic deactivation delay of the bra port.
Default: 30
Unit: second.rw Integer32 .1.3.6.1.4.1.2011.5.25.252.3.1.4 |
hwEntBraPortWorkModeIndicates the bra port working mode.
p2mp(1) -Point to multi-point
p2p(2) -Point to point
Default: p2mp(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.3.1.5 |
hwEntBraPortL1ActiveModeIndicates layer 1 active mode of the bra port.
Options:
stable(1)
unstable(2)
Default: unstable(2).rw Enumeration .1.3.6.1.4.1.2011.5.25.252.3.1.6 |
hwEntBraPortUniAlarmReportIndicates whether to support user network interface fault alarm.
enable(1) -Supported
disable(2) -Not supported
Default: disable(2)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.3.1.7 |
hwEntBraPortL2MonitorIndicates whether to support layer 2 error statistic.
enable(1) -Supported
disable(2) -Not supported
Default: enable(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.3.1.8 |
hwEntBraPortOperTableIndicates the operation table (management, maintenance, and status query) of the bra ports. SEQUENCE OF HwEntBraPortOperEntry .1.3.6.1.4.1.2011.5.25.252.4 |
hwEntBraPortOperEntryIndicates the operation entry (management, maintenance, and status query) of the bra ports. HwEntBraPortOperEntry .1.3.6.1.4.1.2011.5.25.252.4.1 |
hwEntBraPortOperIndexIndicates the BrPortOper index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.4.1.1 |
hwEntBraPortSrvStateIndicates state of the bra port.
Options:
normal(1)
fault(2)
deactive(3)
powerdeny(4)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.4.1.2 |
hwEntBraPortAdminStateIndicates admin state of the bra port.
Options:
noLoopNoTest(1)
noLoopTest(2)
localLoopNoTest(3)
localLoopTest(4)
remoteLoopNoTest(5)
remoteLoopTest(6)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.4.1.3 |
hwEntBraPortAlarmStateIndicates the alarm state of the bra port, from left to right, each bit represents one alarm state.
0 means no alarm present,1 means the alarm present.
bit0: LT overload
bit1: S port fault(EI2)
bit2: U port fault(LOS/RSY)
bit3: S port deactive(SAI)
bit4: U port deactive(ACT)ro Bits .1.3.6.1.4.1.2011.5.25.252.4.1.4 |
hwEntBraPortAdminOperIndicates operation type the bra port.
Options:
remoteLoop(1)
localLoop(2)
cancelLoop(3)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.4.1.5 |
hwEntVe1PortConfigTableIndicates the attribute configuration table of the ve1 ports. SEQUENCE OF HwEntVe1PortConfigEntry .1.3.6.1.4.1.2011.5.25.252.5 |
hwEntVe1PortConfigEntryIndicates the attribute configuration entry of the ve1 ports. HwEntVe1PortConfigEntry .1.3.6.1.4.1.2011.5.25.252.5.1 |
hwEntVe1PortIndexIndicates the slot/subcard/port index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.5.1.1 |
hwEntVe1PortFrameCheckModeIndicates the CRC4 frame check mode of the ve1 port.
Options:
enable(1)
disable(2)
Default: disable(2)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.5.1.2 |
hwEntVe1PortImpedanceIndicates impedance of the ve1 port.
Options:
ohm75(1)
ohm120(2)
Default: ohm75(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.5.1.3 |
hwEntVe1PortSignalTypeIndicates signal type of the ve1 port.
Options:
ccs(1)
cas(2)
Default: ccs(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.5.1.4 |
hwEntVe1PortAccessModeIndicates physical layer digital section access mode of the ve1 port.
Options:
digitalAccess(1)
directAccess(2)
Default:digitalAccess(1)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.5.1.5 |
hwEntVe1PortL2MonitorIndicates whether to support layer 2 error statistic of the ve1 port.
enable(1)
disable(2)
Default: enable(1).rw Enumeration .1.3.6.1.4.1.2011.5.25.252.5.1.6 |
hwEntVe1PortErrAlarmSwitchIndicates ve1 error alarm switches, from left to right, each bit respresent a switch.
0 means disable, 1 means enable.
bit0: report pcm line fault alarm.
bit1: when error rate reached ULF(Unconditional Line Failure) threshold, report pcm line fault alarm.
bit2: when error rate reached OLF(Optional Line Failure) threshold, report pcm line fault alarm.
bit3: when error rate reached LDT(Line Disturbance Transient Event) threshold, report ve1 digital line transient event alarm.
bit4: when E1 frame slip frequency exceeded in observation interval reached degraded threshold, report event alarm.
bit5: when any line temporary event occurs, report event alarm.
Default: 111000rw Bits .1.3.6.1.4.1.2011.5.25.252.5.1.7 |
hwEntVe1PortOperTableIndicates the operation table (management, maintenance, and status query) of the ve1 ports. SEQUENCE OF HwEntVe1PortOperEntry .1.3.6.1.4.1.2011.5.25.252.6 |
hwEntVe1PortOperEntryIndicates the operation entry (management, maintenance, and status query) of the ve1 ports. HwEntVe1PortOperEntry .1.3.6.1.4.1.2011.5.25.252.6.1 |
hwEntVe1PortOperIndexIndicates the Ve1PortOper index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.6.1.1 |
hwEntVe1PortSrvStateIndicates state of the ve1 port.
Options:
normal(1)
fault(2)
lineAbnormal(3)
powerdeny(4)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.6.1.2 |
hwEntVe1PortAdminStateIndicates admin state of the ve1 port.
Options:
noLoopNoTest(1)
noLoopTest(2)
localLoopNoTest(3)
localLoopTest(4)
remoteLoopNoTest(5)
remoteLoopTest(6)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.6.1.3 |
hwEntVe1PortWarningStateIndicates the alarm status of the ve1 line.
0 means no alarm present, 1 means the alarm present.
bit0: LOS alarm
bit1: AIS alarm
bit2: LFA alarm
bit3: LMFA alarm
bit4: RRA alarm
bit5: CRCER alarm
bit6: SCOL alarm
bit7: ULF alarm
bit8: OLF alarm
bit9: LDT alarm
bit10: error second alarm,in direction ET/LT to NT1
bit11: error second alarm,in direction NT1 to ET/LT
bit12: sequential severe error second alarm,in direction ET/LT to NT1
bit13: sequential severe error second alarm,in direction NT1 to ET/LT
bit14: degrade minute alarm,in direction ET/LT to NT1
bit15: degrade minute alarm,in direction NT1 to ET/LTro Bits .1.3.6.1.4.1.2011.5.25.252.6.1.4 |
hwEntVe1PortAdminOperIndicates operation type of the ve1 port.
Options:
remoteLoop(1)
localLoop(2)
cancelLoop(3)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.6.1.5 |
hwEntVe1PortL1AlarmThresholdTabledegrade alarm threshold config table of ve1 port. SEQUENCE OF HwEntVe1PortL1AlarmThresholdEntry .1.3.6.1.4.1.2011.5.25.252.7 |
hwEntVe1PortL1AlarmThresholdEntrydegrade alarm threshold config entry of ve1 port. HwEntVe1PortL1AlarmThresholdEntry .1.3.6.1.4.1.2011.5.25.252.7.1 |
hwEntVe1PortL1AlarmThresholdIndexIndicates the Ve1PortOper index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.7.1.1 |
hwEntVe1PortDmAlarmThresholdIndicates the degrade minute alarm threshold.
Default: 8rw Integer32 .1.3.6.1.4.1.2011.5.25.252.7.1.2 |
hwEntVe1PortEsAlarmThresholdIndicates the error second alarm threshold.
Default: 432rw Integer32 .1.3.6.1.4.1.2011.5.25.252.7.1.3 |
hwEntVe1PortCsesAlarmThresholdIndicates the sequential severe error second alarm threshold.
Default: 4rw Integer32 .1.3.6.1.4.1.2011.5.25.252.7.1.4 |
hwEntFxoPortConfigTableIndicates the attribute configuration table of fxo ports. SEQUENCE OF HwEntFxoPortConfigEntry .1.3.6.1.4.1.2011.5.25.252.8 |
hwEntFxoPortConfigEntryIndicates the attribute configuration entry of fxo ports. HwEntFxoPortConfigEntry .1.3.6.1.4.1.2011.5.25.252.8.1 |
hwEntFxoPortIndexIndicates the slot/subcard/port index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.1 |
hwEntFxoPortSendGainIndicates send gain of the fxo port.
0: 13.5dB, 1: 13.0dB, 2: 12.5dB
3: 12.0dB, 4: 11.5dB, 5: 11.0dB
6: 10.5dB, 7: 10.0dB, 8: 9.5dB
9: 9.0dB, 10: 8.5dB, 11: 8.0dB
12: 7.5dB, 13: 7.0dB, 14: 6.5dB
15: 6.0dB, 16: 5.5dB, 17: 5.0dB
18: 4.5dB, 19: 4.0dB, 20: 3.5dB
21: 3.0dB, 22: 2.5dB, 23: 2.0dB
24: 1.5dB, 25: 1.0dB, 26: 0.5dB
27: 0dB, 28: -0.5dB, 29: -1.0dB
30: -1.5dB, 31: -2.0dB, 32: -2.5dB
33: -3.0dB, 34: -3.5dB, 35: -4.0dB
36: -4.5dB, 37: -5.0dB, 38: -5.5dB
39: -6.0dB, 40: -6.5dB, 41: -7.0dB
42: -7.5dB, 43: -8.0dB, 44: -8.5dB
45: -9.0dB, 46: -9.5dB, 47: -10.0dB
48: -10.5dB, 49: -11.0dB, 50: -11.5dB
51: -12.0dB, 52: -12.5dB, 53: -13.0dB
54: -13.5dB, 55: -14.0dB, 56: -14.5dB
57: -15.0dB, 58: -15.5dB, 59: -16.0dB
60: -16.5dB
Default: 27rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.2 |
hwEntFxoPortRecvGainIndicates receive gain of the fxo port.
0: 13.5dB, 1: 13.0dB, 2: 12.5dB
3: 12.0dB, 4: 11.5dB, 5: 11.0dB
6: 10.5dB, 7: 10.0dB, 8: 9.5dB
9: 9.0dB, 10: 8.5dB, 11: 8.0dB
12: 7.5dB, 13: 7.0dB, 14: 6.5dB
15: 6.0dB, 16: 5.5dB, 17: 5.0dB
18: 4.5dB, 19: 4.0dB, 20: 3.5dB
21: 3.0dB, 22: 2.5dB, 23: 2.0dB
24: 1.5dB, 25: 1.0dB, 26: 0.5dB
27: 0dB, 28: -0.5dB, 29: -1.0dB
30: -1.5dB, 31: -2.0dB, 32: -2.5dB
33: -3.0dB, 34: -3.5dB, 35: -4.0dB
36: -4.5dB, 37: -5.0dB, 38: -5.5dB
39: -6.0dB, 40: -6.5dB, 41: -7.0dB
42: -7.5dB, 43: -8.0dB, 44: -8.5dB
45: -9.0dB, 46: -9.5dB, 47: -10.0dB
48: -10.5dB, 49: -11.0dB, 50: -11.5dB
51: -12.0dB, 52: -12.5dB, 53: -13.0dB
54: -13.5dB, 55: -14.0dB, 56: -14.5dB
57: -15.0dB, 58: -15.5dB, 59: -16.0dB
60: -16.5dB
Default: 34rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.3 |
hwEntFxoPortDcImpedanceIndicates DC impedance of the fxo port.
0: 50
1: 800
Default: 0
Unit:rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.4 |
hwEntFxoPortAcImpedanceIndicates AC impedance of the fxo port.
0: 600
1: 900
2: 270 + (750 || 150 nF) and 275 + (780 || 150 nF)
3: 220 + (820 || 120 nF) and 220 + (820 || 115 nF)
4: 370 + (620 || 310 nF)
5: 320 + (1050 || 230 nF)
6: 370 + (820 || 110 nF)
7: 275 + (780 || 115 nF)
8: 20 + (820 || 110 nF)
9: 350 + (1000 || 210 nF)
10: 200 + (680 || 100 nF)
11: 600 + 2.16 F
12: 900 + 1 F
13: 900 + 2.16 F
14: 600 + 1 F
15: Global impedance
Default: 0
Unit:rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.5 |
hwEntFxoPortRingMinDurationIndicates the min of the ring duration time.
0: 100ms
1: 150ms
2: 200ms
3: 256ms
4: 384ms
5: 512ms
6: 640ms
7: 1024ms
Default: 2rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.6 |
hwEntFxoPortRingMaxIntervalIndicates the max of the ring interval time.
0: not use, 1: 128ms, 2: 256ms, 3: 284ms
4: 512ms, 5: 640ms, 6: 768ms, 7: 896ms
8: 1024ms, 9: 1152ms, 10: 1280ms, 11: 1408ms
12: 1536ms, 13: 1664ms, 14: 1792ms, 15: 1920ms
16: 2000ms, 17: 2500ms, 18: 3000ms, 19: 3500ms
20: 4000ms, 21: 4500ms, 22: 5000ms, 23: 6000ms
24: 7000ms, 25: 8000ms, 26: 9000ms, 27: 10000ms
28: 15000ms
Default: 0rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.7 |
hwEntFxoPortRingFrequencyIndicates the ring frequency.
0: 16Hz
1: 25Hz
2: 50Hz
Default: 1rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.8 |
hwEntFxoPortRingAcAmplitudeIndicates the ring of the AC amplitude.
0: 74V
1: 65V
2: 50V
Default: 2rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.9 |
hwEntFxoPortRingOffsetIndicates the ring offset.
0-100: -50V ~ 50V
Default: 70rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.10 |
hwEntFxoPortFeedMaxVoltageIndicates the max feed voltage.
Default: -20
Unit:Vrw Integer32(-100..0) .1.3.6.1.4.1.2011.5.25.252.8.1.11 |
hwEntFxoPortFeedMinVoltageIndicates the min feed voltage.
Default: -80
Unit:Vrw Integer32(-100..0) .1.3.6.1.4.1.2011.5.25.252.8.1.12 |
hwEntFxoPortFeedMaxCurrentIndicates the max feed current.
0: 25mA
1: 30mA
2: 35mA
3: 40mA
Default: 2rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.13 |
hwEntFxoPortFeedMinCurrentIndicates the min of the PTP feed current.
0: 16mA
1: 17mA
2: 18mA
3: 19mA
4: 20mA
Default: 0rw Integer32 .1.3.6.1.4.1.2011.5.25.252.8.1.14 |
hwEntFxoPortOperTableIndicates the operation table (management, maintenance, and status query) of the fxo ports. SEQUENCE OF HwEntFxoPortOperEntry .1.3.6.1.4.1.2011.5.25.252.9 |
hwEntFxoPortOperEntryIndicates the operation entry (management, maintenance, and status query) of the fxo ports. HwEntFxoPortOperEntry .1.3.6.1.4.1.2011.5.25.252.9.1 |
hwEntFxoPortOperIndexIndicates the FxsPortOper index.
bits 31-24 (8 bits): reserved
bits 23-16 (8 bits): slot index
bits 15-8 (8 bits): subcard index
bits 7-0 (8 bits): port index Integer32 .1.3.6.1.4.1.2011.5.25.252.9.1.1 |
hwEntFxoPortSrvStateIndicates state of the fxo port.
Options:
normal(1)
fault(2)
deactive(3)
powredeny(4)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.9.1.2 |
hwEntFxoPortAdminStateIndicates the fxo port Admin state.
Options:
noLoopNoTest(1)
noLoopTest(2)
localLoopNoTest(3)
localLoopTest(4)
remoteLoopNoTest(5)
remoteLoopTest(6)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.9.1.3 |
hwEntFxoPortLineStateIndicates line state of the fxo port.
Options:
normal(1)
fault(2)
unknown(3)ro Enumeration .1.3.6.1.4.1.2011.5.25.252.9.1.4 |
hwEntFxoPortAdminOperIndicates the operate type.
Options:
remoteLoop(1)
localLoop(2)
cancelLoop(3)rw Enumeration .1.3.6.1.4.1.2011.5.25.252.9.1.5 |
hwEntVoicePortConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.252.10 |
hwEntVoicePortCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.252.10.1 |
hwEntVoicePortGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.252.10.2 |