HP-ICF-BRIDGE
This MIB module supports loop protect per vlan feature.
Main OID:
hpicfBridge.1.3.6.1.4.1.25506.11.1.12
71
Objects
Active
Status
10
Dependencies
Imported Objects
Objects
71 total| Object Name |
|---|
hpicfBridgeThis MIB module supports loop protect per vlan feature. MODULE-IDENTITY .1.3.6.1.4.1.25506.11.1.12 |
IMPORTSThis MIB module supports loop protect per vlan feature. Unknown .1.3.6.1.4.1.25506.11.1.12 |
hpicfBridgeObjects OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1 |
hpicfBridgeBase OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.1 |
hpicfBridgeMaxVlansDefines the number of VLANs that the switch will
support for dynamic use without requiring a reboot.rw Integer32 .1.3.6.1.4.1.25506.11.1.12.1.1.1 |
hpicfBridgeVlanEnableAdministrative status of VLAN support on this
switch.rw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.1.2 |
hpicfBridgePrimaryVlanThe 802.1Q VLAN ID of the primary VLAN for this
switch.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.25506.11.1.12.1.1.3 |
hpicfBridgeVlanConfigStatusIf one or more variables in this group has been
reconfigured since the last reboot in such a way
as to require a reboot to take effect, the value
of this variable will be set to 'notInService'.ro ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.12.1.1.4 |
hpicfBridgeGvrp OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.2 |
hpicfBridgeGvrpPortTableA table that contains information about the
GVRP port configurations on this switch. SEQUENCE OF HpicfBridgeGvrpPortEntry .1.3.6.1.4.1.25506.11.1.12.1.2.1 |
hpicfBridgeGvrpPortEntryGVRP information associated with a single port. HpicfBridgeGvrpPortEntry .1.3.6.1.4.1.25506.11.1.12.1.2.1.1 |
hpicfBridgeGvrpRestrictedVlanRegControls GVRP's ability to learn new VLANs on
this port. When set to 'false', GVRP will accept
JOIN requests for new VLANs on this port. When
set to 'true', GVRP will only process protocol
packets that concern themselves with known VLANs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.2.1.1.1 |
hpicfBridgeRstp OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.4 |
hpicfBridgeRstpForceVersionOperational mode of Spanning Tree protocol:
- stpCompatibility means protocol operates as STP protocol
on all ports.
- rstpOperation means protocol operates as Rapid
Reconfiguration on all ports except on those ports where
legacy system has been detected.
- mstpOperation means protocol operates in native MSTP mode,
this option is available only if object
'hpicfBridgeRstpProtocolVersion' is set to 'ieee8021s'.rw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.4.1 |
hpicfBridgeRstpConfigStatusThe configuration status of this group of objects. If
one or more variables in this group were
reconfigured since last reboot and required reboot to
take effect, the value of this variable will be set to
notInService.ro ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.12.1.4.2 |
hpicfBridgeRstpProtocolVersionThe protocol version currently running on switch
- ieee8021d version of STP protocol,
- ieee8021w Rapid Reconfiguration version of STP protocol,
- ieee8021s Multiple STP (MSTP) protocolrw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.4.3 |
hpicfBridgeRstpAdminStatusThe operational status of the spanning tree protocolrw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.4.4 |
hpicfBridgeRstpPortTableA table that contains port-specific information
for the Spanning Tree Protocol. SEQUENCE OF HpicfBridgeRstpPortEntry .1.3.6.1.4.1.25506.11.1.12.1.4.5 |
hpicfBridgeRstpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. HpicfBridgeRstpPortEntry .1.3.6.1.4.1.25506.11.1.12.1.4.5.1 |
hpicfBridgeRstpPortIndexThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro Integer32 .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.1 |
hpicfBridgeRstpAdminEdgePortIndicate that port is connected to LAN segment that don't
have any bridge connected to itrw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.2 |
hpicfBridgeRstpOperEdgePortReflects the value of the operEdgePort parameter, as
defined by the operation of the Bridge Detection state
machine (Clause 18 of P802.1t). The value of this parameter
is used by a Designated Port in order to determine how
rapidly it may transition to the Forwarding Port State
(see 17.23, Port Role Transitions state machine).
The Bridge Detection state machine sets this parameter to
the value of adminEdgePort (P802.1t 18.1.3) on
initialization, and forces its value to FALSE if any BPDUs
are received on the Port.ro Enumeration .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.3 |
hpicfBridgeRstpAdminPointToPointMacforceTrue: This value indicates that the administrator requires the MAC
to be treated as if it is connected to a point-to-point LAN
segment, regardless of any indications to the contrary that
are generated by the MAC entity.
forceFalse: This value indicates that the administrator requires the MAC
to be treated as if it is connected to a non-point-to-point
LAN segment, regardless of any indications to the contrary
that are generated by the MAC entity.
auto: This value indicates that the administrator requires the
point-to-point status of the MAC to be determined in accordance
with the specific MAC procedures defined in 6.5.rw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.4 |
hpicfBridgeRstpOperPointToPointMactrue: This value indicates that the MAC is connected to a
point-to-point LAN segment; i.e., there is at most one other
system attached to the LAN segment.
false: This value indicates that the MAC is connected to a
non-point-to-point LAN segment; i.e., there can be more than one
other system attached to the LAN segment.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.5 |
hpicfBridgeRstpPortPathCostRapid Reconfiguration Port Path Cost - 32 bit valuesrw Integer32 .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.6 |
hpicfBridgeRstpForceBpduMigrationCheckWhen operating in RST (version 2 or greater) mode
writing TRUE(1) to this object forces this port to
transmit RST BPDUs. Any other operation on this object
has no effect and it always returns FALSE(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.7 |
hpicfBridgeRstpAutoEdgePortRepresents the value of 'autoEdgePort' parameter.
This parameter is optional. It is used by the Bridge
Detection state machine for the automatic identification
of edge ports. The default is false.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.8 |
hpicfBridgeRstpPortBpduFilteringThis value indicates whether or not BPDUs need
to be filtered on this port. If the value is true the
received BPDUs will be dropped and no BPDUs will be
transmitted on the port. If the value is false the BPDUs
are being processed as usual. The default is false.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.4.5.1.9 |
hpicfBridgeLoopProtect OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.5 |
hpicfBridgeLoopProtectNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.5.0 |
hpicfBridgeLoopProtectLoopDetectedNotificationA hpicfBridgeLoopProtectLoopDetectedNotification signifies
that a loop has been detected by the loop protection protocol.
Generation of this notification is controlled by
hpicfBridgeLoopProtectTrapLoopDetectEnable. To prevent
excessive notifications this trap is rate-limited to allow
a maximum of 1 notifications every 30 seconds.
Notifications that are not sent due to rate-limiting are
dropped, and not queued up to be sent later. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.11.1.12.1.5.0.1 |
hpicfBridgeVlanLoopProtectLoopDetectedNotificationA hpicfBridgeLoopProtectLoopDetectedNotification signifies
that a loop has been detected by the loop protect while
operating on a per VLAN mode.
Generation of this notification is controlled by
hpicfBridgeLoopProtectTrapLoopDetectEnable. To prevent
excessive notifications this trap is rate-limited to allow
a maximum of 1 notifications every 30 seconds.
Notifications that are not sent due to rate-limiting are
dropped, and not queued up to be sent later. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.11.1.12.1.5.0.2 |
hpicfBridgeLoopProtectBase OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.5.1 |
hpicfBridgeLoopProtectIntervalThe interval in seconds at which loop protection packets are
transmitted. The default value is 5 seconds.rw Integer32 .1.3.6.1.4.1.25506.11.1.12.1.5.1.1 |
hpicfBridgeLoopProtectTrapLoopDetectEnableIndicates whether notifications should be sent when a loop
is detected on a port. By default this object will
have a value of false(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.5.1.2 |
hpicfBridgeLoopProtectEnableTimerThe time in seconds to wait before re-enabling a port
disabled by loop protection. When a port is disabled by
loop protection a re-enable timer for the port is initialized
with the value of this period. If the period is not equal to
zero the port will be re-enabled after the period has
elapsed. Otherwise the port will remain disabled.rw Integer32 .1.3.6.1.4.1.25506.11.1.12.1.5.1.3 |
hpicfBridgeLoopProtectModeThis value indicate whether loop protect operates in
Port or VLAN mode.rw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.5.1.4 |
hpicfBridgeLoopProtectVIDListA list of VLANs on which loop protection is enabled.rw VidList (HP-ICF-FTRCO) .1.3.6.1.4.1.25506.11.1.12.1.5.1.5 |
hpicfBridgeLoopProtectPort OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.5.2 |
hpicfBridgeLoopProtectPortTablePer-interface configuration for Loop Protection. SEQUENCE OF HpicfBridgeLoopProtectPortEntry .1.3.6.1.4.1.25506.11.1.12.1.5.2.1 |
hpicfBridgeLoopProtectPortEntryLoop Protection configuration information for
a single port. HpicfBridgeLoopProtectPortEntry .1.3.6.1.4.1.25506.11.1.12.1.5.2.1.1 |
hpicfBridgeLoopProtectPortEnableThis object indicates whether this port has
Loop protection enabled. The default value is FALSErw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.5.2.1.1.1 |
hpicfBridgeLoopProtectPortLoopDetectedThis object will be set to TRUE when a loop is detected on
the port. The value of this object will be reset to FALSE when
the port's hpicfBridgeLoopProtectPortEnable is set to
FALSE.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.5.2.1.1.2 |
hpicfBridgeLoopProtectPortLastLoopTimeThe value of sysUpTime when a loop was last detected
on this port. A value of 0 means that the timestamp has
not been set.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.5.2.1.1.3 |
hpicfBridgeLoopProtectPortLoopCountWhen the loop protect feature is enabled on the port this
object counts the number of loops detected on the port.
When the feature is disabled on the port the value of this
object is set to 0.ro Counter32 .1.3.6.1.4.1.25506.11.1.12.1.5.2.1.1.4 |
hpicfBridgeLoopProtectPortReceiverActionControls the action taken when a Loop protection packet is
received on this port. When set to 'disableTx' the port
that transmitted the packet will be disabled. When set to
'noDisable' the transmitting port will not be disabled.rw LoopProtectReceiverAction .1.3.6.1.4.1.25506.11.1.12.1.5.2.1.1.5 |
hpicfBridgeLoopDetectedVlanRefers to this object for the port on which loop is
detected.ro Integer32 .1.3.6.1.4.1.25506.11.1.12.1.5.2.1.1.6 |
hpicfBridgeMirrorSession OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.6 |
hpicfBridgeMirrorSessionBase OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.6.1 |
hpicfBridgeMirrorSessionDestination OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.6.2 |
hpicfBridgeMirrorSessionTableThis table contains mirror session information
related to a given specified destination. A mirror
session is a group of one or more portCopyEntries
all having the same specified destination. A given
specified destination may be associated with more
then one mirror session. SEQUENCE OF HpicfBridgeMirrorSessionEntry .1.3.6.1.4.1.25506.11.1.12.1.6.2.1 |
hpicfBridgeMirrorSessionEntryAn entry in the hpicfBridgeMirrorSessionEntry contains
mirror session specific identification
information. HpicfBridgeMirrorSessionEntry .1.3.6.1.4.1.25506.11.1.12.1.6.2.1.1 |
hpicfBridgeMirrorSessionIDThis variable is valid only for mirroring
transfers. It allows mirroring destinations
to be grouped. A given hpicfBridgeMirrorSessionID
can only be used with 1 destination. However,
multiple sources may be related to the same
hpicfBridgeMirrorSessionID. To ensure that the
hpicfBridgeMirrorSessionID is properly assigned,
it can only be updated when the respective
portCopyEntry object is in the notReady state.
For non-mirroring transfers, the value should
be set to 0.rw Integer32 .1.3.6.1.4.1.25506.11.1.12.1.6.2.1.1.1 |
hpicfBridgeDontTagWithVlanThis oid mentions whether VLAN tag is to part of the
mirrored copy of the packet. The value 'enabled'
denotes that the VLAN tag should not be part of the
mirrored copy; 'disabled' does put the VLAN tag in the
mirrored copy. Only one logical port is allowed.
This object is persistent and when written the entity
SHOULD save the change to non-volatile storage.rw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.6.2.1.1.2 |
hpicfBridgeMirrorSessionTypeThis oid mentions what is the source type of traffic
associated with mirror session.
noMirror Not associated with any mirroring.
mirrorAddresses Mirror traffic based on addresses
mirrorPolicies Mirror traffic based on policies.
mirrorPorts Mirror traffic based on ports.
mirrorVlan Mirror traffic based on vlan.rw Enumeration .1.3.6.1.4.1.25506.11.1.12.1.6.2.1.1.3 |
hpicfBridgeVoiceVlanConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.7 |
hpicfBridgeVoiceVlanConfigTableHP specific extension to dot1qVlanStaticTable to
for configuring voice on a vlan. SEQUENCE OF HpicfBridgeVoiceVlanConfigEntry .1.3.6.1.4.1.25506.11.1.12.1.7.1 |
hpicfBridgeVoiceVlanConfigEntryAn entry for HP Specific extension table. HpicfBridgeVoiceVlanConfigEntry .1.3.6.1.4.1.25506.11.1.12.1.7.1.1 |
hpicfBridgeVoiceVlanEnableLabels the VLAN as a Voice VLAN which allows
to separate, prioritize, and authenticate voice
traffic moving through the network.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.7.1.1.1 |
hpicfBridgeJumboInterfaceConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.8 |
hpicfBridgeJumboInterfaceConfigTableThis table contains objects for configuring voice on
a interface. SEQUENCE OF HpicfBridgeJumboInterfaceConfigEntry .1.3.6.1.4.1.25506.11.1.12.1.8.1 |
hpicfBridgeJumboInterfaceConfigEntryAn entry in the hpicfBridgeJumboInterfaceConfigEntry contains
jumbo configuration for a interface. HpicfBridgeJumboInterfaceConfigEntry .1.3.6.1.4.1.25506.11.1.12.1.8.1.1 |
hpicfBridgeJumboInterfaceEnableLabels the interface as a Jumbo Interface which allows to pass
packets up to 9220 bytes in size. Currently this configuration
is supported only on vlan.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.8.1.1.1 |
hpicfBridgeManagementInterfaceConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.1.9 |
hpicfBridgeManagementInterfaceConfigTableThis table contains objects for configuring interface as
Management interface. SEQUENCE OF HpicfBridgeManagementInterfaceConfigEntry .1.3.6.1.4.1.25506.11.1.12.1.9.1 |
hpicfBridgeManagementInterfaceConfigEntryAn entry in the hpicfBridgeManagementInterfaceConfigEntry
contains objects for configuring interface as management
interface. HpicfBridgeManagementInterfaceConfigEntry .1.3.6.1.4.1.25506.11.1.12.1.9.1.1 |
hpicfBridgeManagementInterfaceEnableLabels the interface as management interface. Currently,
only one vlan can be management interface on the switch.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.12.1.9.1.1.1 |
hpicfBridgeConformance OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.2 |
hpicfBridgeGroups OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.2.1 |
hpicfBridgeCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.2.2 |
hpicfBridgeNotGroups OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.12.2.3 |