HH3C-EPON-MIB
The objects in this MIB module are used to manage and display current configuration of Ethernet Passive Optical Network (EPON) port which are based on the Ethernet in the First Mile (EFM) Passive Optical Network(PON) as defined in IEEE Draft P802.3ah/D3.0 clause 60, 64, 65..
Main OID:
hh3cEponMibObjects.1.3.6.1.4.1.25506.2.42.1
424
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
424 total| Object Name |
|---|
hh3cEponMibObjectsThe objects in this MIB module are used to manage and display current configuration of Ethernet Passive Optical Network (EPON) port which are based on the Ethernet in the First Mile (EFM) Passive Optical Network(PON) as defined in IEEE Draft P802.3ah/D3.0 clause 60, 64, 65.. MODULE-IDENTITY .1.3.6.1.4.1.25506.2.42.1 |
hh3cEponSysMan OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.1 |
hh3cEponAutoAuthorizeThis value determines whether software performs self-authorization for each Optical Network Unit(ONU) registering to the network. Setting it to false means for every ONU registering, software requires external authorization, and until it's done the ONU is not authenticated. True value means software authorizes each ONU registering to the network automatically. true - ONUs are always authorized. false - If 802.1x authorization is enable, the ONUs have to be authorized by the protocol. - If 802.1x authorization is disable, ONUs are always authorized.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.1.1 |
hh3cEponMonitorCycleThe cycle of alarm thresholds checking. Applying to the following types: Bit Error Rate(BER) alarm, Frame Error Rate(FER), Logical Link Identity(LLID) mismatch alarm and so on. The unit is second.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.1.2 |
hh3cEponMsgTimeOutTimeout waiting for a response from Optical Line Terminal(OLT) firmware after sending it a message. The unit is millisecond.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.1.3 |
hh3cEponMsgLoseNumThe times of messages sending timeouts, after which OLT will reset (applying to every OLT).rw Integer32 .1.3.6.1.4.1.25506.2.42.1.1.4 |
hh3cEponSysHasEPONBoardtrue(1) - At least an EPON board exists. false(2) - No EPON board exists.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.1.5 |
hh3cEponMonitorCycleEnableStop or continue monitoring. true(1) - Continue monitoring. false(2) - Stop monitoring.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.1.6 |
hh3cEponOltSoftwareErrAlmEnableSoftware error alarm behavior of all active OLTs. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.1.7 |
hh3cEponPortLoopBackAlmEnableLoopBack alarm behavior of EPON ports. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.1.8 |
hh3cEponMonitorCycleMinValThe lower limit of cycle which be confined to the hh3cEponMonitorCycle.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.1.9 |
hh3cEponMonitorCycleMaxValThe upper limit of cycle which be confined to the hh3cEponMonitorCycle.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.1.10 |
hh3cEponMsgTimeOutMinValThe lower limit of timeout which be confined to the hh3cEponMsgTimeOut.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.1.11 |
hh3cEponMsgTimeOutMaxValThe upper limit of timeout which be confined to the hh3cEponMsgTimeOut.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.1.12 |
hh3cEponMsgLoseNumMinValThe lower limit of time which be confined to the hh3cEponMsgLoseNum.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.1.13 |
hh3cEponMsgLoseNumMaxValThe upper limit of time which be confined to the hh3cEponMsgLoseNum.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.1.14 |
hh3cEponSysScalarGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.1.15 |
hh3cEponSysManTableThis table defines system related parameters. SEQUENCE OF Hh3cEponSysManEntry .1.3.6.1.4.1.25506.2.42.1.1.16 |
hh3cEponSysManEntryThe entry of the table hh3cEponSysManTable. Hh3cEponSysManEntry .1.3.6.1.4.1.25506.2.42.1.1.16.1 |
hh3cEponSlotIndexSlot Index, the index of hh3cEponSysManTable. Integer32 .1.3.6.1.4.1.25506.2.42.1.1.16.1.1 |
hh3cEponModeSwitchcmode - epon standard mode. hmode - private mode.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.1.16.1.2 |
hh3cEponAutomaticModeAutomatic mode setting: when enabled - after new OLT is added, the OLT stack sets its encryption mode to 'triple churning' and configure the OLT to authorize ONU MAC addresses according to its table. enable -enable automatic mode. disable -disable automatic mode.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.1.16.1.3 |
hh3cEponOamDiscoveryTimeoutTime out parameter for extended OAM discovery process message, ranging from 0 to 2550, measured in 100 milliseconds.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.1.16.1.4 |
hh3cEponEncryptionNoReplyTimeOutEncryption response timeout, ranging from 1 to 2550, measured in 100 milliseconds.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.1.16.1.5 |
hh3cEponEncryptionUpdateTimeEncryption key update timer for all ONUs on slot, indicated by hh3cEponSlotIndex, ranging from 1 to 255, measured in seconds.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.1.16.1.6 |
hh3cEponAutoBindStatusenable - auto bind ONU ID when the ONU registered in the EPON system. disable - need manual bind ONU ID when the ONU registered in the EPON system.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.1.16.1.7 |
hh3cEponAutoUpdateTableEPON auto update ONU application configuration. SEQUENCE OF Hh3cEponAutoUpdateEntry .1.3.6.1.4.1.25506.2.42.1.1.17 |
hh3cEponAutoUpdateEntryThe entry of the table hh3cEponAutoUpdateTable. Hh3cEponAutoUpdateEntry .1.3.6.1.4.1.25506.2.42.1.1.17.1 |
hh3cEponAutoUpdateFileNameThe name of ONU application file, the file name must be valid and include the path. It is a zero length string by default.rw DisplayString .1.3.6.1.4.1.25506.2.42.1.1.17.1.1 |
hh3cEponAutoUpdateSchedStatusThe status of schedule update configuration. The hh3cEponAutoUpdateFileName must be set before enable hh3cEponAutoUpdateSchedStatus. enable - enable ONU schedule update. disable - disable ONU schedule update.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.1.17.1.2 |
hh3cEponAutoUpdateSchedTimeThe schedule update timing configuration is related to the hh3cEponAutoUpdateSchedType. auto update daily: the string format is hhmm auto update weekly: the string format is hhmmw 'w' means update weekly, it ranges from 0 to 6: 0 - Sunday. 1 - Monday. 2 - Tuesday. 3 - Wednesday. 4 - Thursday. 5 - Friday. 6 - Saturday. auto update in coming date : the string format is hhmmyyyymmdd. The configuration will take effect only if hh3cEponAutoUpdateSchedStatus is enabled.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.1.17.1.3 |
hh3cEponAutoUpdateSchedTypeThe update type of auto updating configuration. daily - update ONU application every day. weekly - update ONU application every week. comingdate - update ONU application on coming date.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.1.17.1.4 |
hh3cEponAutoUpdateRealTimeStatusThe status of real time update configuration. The hh3cEponAutoUpdateFileName must be set before enable hh3cEponAutoUpdateRealTimeStatus. enable - enable ONU real time update. disable - disable ONU real time update.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.1.17.1.5 |
hh3cEponOuiIndexNextTableNext OUI index table. SEQUENCE OF Hh3cEponOuiIndexNextEntry .1.3.6.1.4.1.25506.2.42.1.1.18 |
hh3cEponOuiIndexNextEntryThe entry of the table hh3cEponOuiIndexNextTable. Hh3cEponOuiIndexNextEntry .1.3.6.1.4.1.25506.2.42.1.1.18.1 |
hh3cEponOuiIndexNextThis object contains an appropriate value to be used for hh3cEponOuiIndex when creating rows in the hh3cEponOuiTable.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.1.18.1.1 |
hh3cEponOuiTableList of OUI and OAM supported by OLT. SEQUENCE OF Hh3cEponOuiEntry .1.3.6.1.4.1.25506.2.42.1.1.19 |
hh3cEponOuiEntryThe entry of the table hh3cEponOuiTable. Hh3cEponOuiEntry .1.3.6.1.4.1.25506.2.42.1.1.19.1 |
hh3cEponOuiIndexThe index of this table. Integer32 .1.3.6.1.4.1.25506.2.42.1.1.19.1.1 |
hh3cEponOuiValueOUI list supported by the extended OAM discovery process. The OUI is composed of six octets. The first six octets denote the first OUI , the second six octets denote the second OUI, and the like.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.1.19.1.2 |
hh3cEponOamVersionVersion of OAM protocol defined by the organization denoted by OUI.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.1.19.1.3 |
hh3cEponOuiRowStatusThe status of this table entry. Only active, createAndGo and the destory are supported.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.1.19.1.4 |
hh3cEponMulticastControlTableMulticast control global configuration. SEQUENCE OF Hh3cEponMulticastControlEntry .1.3.6.1.4.1.25506.2.42.1.1.20 |
hh3cEponMulticastControlEntryThe entry of the table hh3cEponMulticastControlTable. Hh3cEponMulticastControlEntry .1.3.6.1.4.1.25506.2.42.1.1.20.1 |
hh3cEponMulticastVlanIdThe index of this table. Integer32 .1.3.6.1.4.1.25506.2.42.1.1.20.1.1 |
hh3cEponMulticastAddressListThe multicast address, each four octets represents a multicast address, the address section ranging from the first four octets to the second four octets, and the like.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.1.20.1.2 |
hh3cEponMulticastStatusThe status of this table entry. Only active, createAndGo and the destory are supported.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.1.20.1.3 |
hh3cEponFileName OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.2 |
hh3cEponDbaUpdateFileNameThe name of a binary file which is loaded to the OLT from an external source. Note that the filename must contain the file path.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.2.1 |
hh3cEponOnuUpdateFileNameThe filename of the ONU firmware to be updated. Note that the filename must contain the file path.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.2.2 |
hh3cEponOltMan OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.3 |
hh3cOltSysManTableThis table defines several OLT system parameters: (1)laser on time (2)laser off time (3)whether multiple copy broadcast (4)whether discard packet (5)self test (6)self test result SEQUENCE OF Hh3cOltSysManEntry .1.3.6.1.4.1.25506.2.42.1.3.1 |
hh3cOltSysManEntryThe entry of the table hh3cOltSysManTable. Hh3cOltSysManEntry .1.3.6.1.4.1.25506.2.42.1.3.1.1 |
hh3cOltLaserOnTimeThe laser on time of the ONUs during the discovery process, measured in Time Quanta(TQ).rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.1.1.1 |
hh3cOltLaserOffTimeThe laser off time of the ONUs during the discovery process, measured in TQ.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.1.1.2 |
hh3cOltMultiCopyBrdCasttrue/false filtering of tagged multicast frames. The software avert tagged downstream frames with multicast or broadcast DA to the PON and not to the CPU, except for special multicast frames (link-constraint, IGMP control and ARP) that are passed to the CPU regardless of this feature.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.1.1.3 |
hh3cOltEnableDiscardPacketForward(false)/discard(true) any frames received from unlearned source address when the inside address table of the original ONU entry reach to the limit.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.1.1.4 |
hh3cOltSelfTestselftest(1): Test OLT to check whether it's OK.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.3.1.1.5 |
hh3cOltSelfTestResultThe self test result of the specific OLT. other(1): The self test result is another reason. ok(2): The self test result is OK. fail(3): The self test result is fail.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.3.1.1.6 |
hh3cOltMaxRttSet the max Round Trip Time of this OLT.rw Unsigned32 .1.3.6.1.4.1.25506.2.42.1.3.1.1.7 |
hh3cOltInfoTablePrimary status of the specified OLT. There will be one row in this table for each information in the system. (1)Software and hardware versions of the specified OLT (hh3cOltFirmMajorVersion, hh3cOltFirmMinorVersion, hh3cOltHardMajorVersion, hh3cOltHardMinorVersion) (2)Several physical capabilities of an OLT device. (hh3cOltAgcLockTime, hh3cOltAgcCdrTime) (3)The operation(activation) status of an OLT. (hh3cOltMacAddress, hh3cOltWorkMode) SEQUENCE OF Hh3cOltInfoEntry .1.3.6.1.4.1.25506.2.42.1.3.2 |
hh3cOltInfoEntryThe entry of the table hh3cOltInfoTable. Hh3cOltInfoEntry .1.3.6.1.4.1.25506.2.42.1.3.2.1 |
hh3cOltFirmMajorVersionOLT firmware major version. If the object length is zero, it means the version is unknown.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.3.2.1.1 |
hh3cOltFirmMinorVersionOLT firmware minor version. If the object length is zero, it means the version is unknown.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.3.2.1.2 |
hh3cOltHardMajorVersionOLT hardware major version. If the object length is zero, it means the version is unknown.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.3.2.1.3 |
hh3cOltHardMinorVersionOLT hardware minor version. If the object length is zero, it means the version is unknown.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.3.2.1.4 |
hh3cOltAgcLockTimePON upstream data Automatic Gain Control(AGC) lock time, measured in TQ, range: 1 - 2^15. 0x7FFFFFFF: unknown value.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.2.1.5 |
hh3cOltAgcCdrTimePON RX signal synchronization time, measured in TQ, range: 1 - 2^15. 0x7FFFFFFF: unknown valuero Integer32 .1.3.6.1.4.1.25506.2.42.1.3.2.1.6 |
hh3cOltMacAddressOLT MAC address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.2.1.7 |
hh3cOltWorkModeThe operation(activation) modes of an OLT. other(1) - The OLT is in another mode. open(2) - The OLT is open. reset(3) - The OLT is reset. closed(4) - The OLT is closed.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.3.2.1.8 |
hh3cOltOpticalPowerTxThe optical power transmitted by this OLT. It measured in 0.01 dBm unit.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.2.1.9 |
hh3cOltOpticalPowerRxThe burst optical power received by this OLT. It measured in 0.01 dBm unit.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.2.1.10 |
hh3cOltDbaManTableThis table defines the primary parameters of the Dynamic Bandwidth Allocation(DBA) algorithm applying to the OLT. SEQUENCE OF Hh3cOltDbaManEntry .1.3.6.1.4.1.25506.2.42.1.3.3 |
hh3cOltDbaManEntryThe entry of the table hh3cOltDbaManTable. Hh3cOltDbaManEntry .1.3.6.1.4.1.25506.2.42.1.3.3.1 |
hh3cOltDbaEnabledTypeEnable different types of the DBA algorithm. Start upstream dynamic bandwidth allocation algorithm, replacing former bandwidth allocation mechanism. internal(1) - OLT internal Service Level Agreement(SLA) based algorithm, always being activated. external(2) - DBA algorithm in a binary file which is loaded to the OLT from an external source.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.3.3.1.1 |
hh3cOltDbaDiscoveryLengthDiscovery length in TQ units.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.3.1.2 |
hh3cOltDbaDiscovryFrequencyHow often should the OLT send discovery frames to the ONUs, measured in grant cycles.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.3.1.3 |
hh3cOltDbaCycleLengthThe grant cycle length in TQ units.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.3.1.4 |
hh3cOltDbaVersionDBA version of the OLT.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.3.3.1.5 |
hh3cOltDbaUpdateUpdate(1): Update the DBA algorithm with a binary file which is loaded to the OLT from an external source(flash). Config the MIB object module hh3cEponDbaUpdateFileName.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.3.3.1.6 |
hh3cOltDbaUpdateResultThe latest DBA update result. other: The DBA update result is another reason. ok: The DBA update result is OK. fail: The DBA update result is fail. fileNotExist: The DBA update failed because the file does not exist. notSetFilename: The DBA filename is not set.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.3.3.1.7 |
hh3cOltPortAlarmThresholdTableThe table defines the alarm threshold of OLT. SEQUENCE OF Hh3cOltPortAlarmThresholdEntry .1.3.6.1.4.1.25506.2.42.1.3.4 |
hh3cOltPortAlarmThresholdEntryThe entry of the table hh3cOltPortAlarmThresholdTable. Hh3cOltPortAlarmThresholdEntry .1.3.6.1.4.1.25506.2.42.1.3.4.1 |
hh3cOltPortAlarmBerEnabledBehavior of BER alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.1 |
hh3cOltPortAlarmBerDirectTraffic direction to monitor for BER alarm.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.3.4.1.2 |
hh3cOltPortAlarmBerThresholdBER threshold exceed which the alarm is raised.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.4.1.3 |
hh3cOltPortAlarmFerEnabledBehavior of FER alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.4 |
hh3cOltPortAlarmFerDirectTraffic direction to monitor for FER alarm.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.3.4.1.5 |
hh3cOltPortAlarmFerThresholdFrame error rate exceed threshold then the alarm is raised.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.4.1.6 |
hh3cOltPortAlarmLlidMismatchEnabledBehavior of LLID mismatch alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.7 |
hh3cOltPortAlarmLlidMismatchThresholdThe minimal number of mismatched frames exceed threshold then LLID mismatch alarm is raised.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.3.4.1.8 |
hh3cOltPortAlarmRemoteStableEnabledBehavior of remote stable alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.9 |
hh3cOltPortAlarmLocalStableEnabledBehavior of local stable alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.10 |
hh3cOltPortAlarmRegistrationEnabledBehavior of registration alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.11 |
hh3cOltPortAlarmOamDisconnectionEnabledBehavior of Operations Administration and Maintenance(OAM) disconnection alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.12 |
hh3cOltPortAlarmEncryptionKeyEnabledBehavior of encryption bad key alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.13 |
hh3cOltPortAlarmVendorSpecificEnabledBehavior of vendor specific alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.14 |
hh3cOltPortAlarmRegExcessEnabledBehavior of ONU registering over limitation alarm. true(1) - alarm enable. false(2) - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.15 |
hh3cOltPortAlarmDFEEnabledBehavior of device fatal error alarm. true - alarm enable. false - alarm disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.4.1.16 |
hh3cOltLaserOnTimeMinValThe lower limit of time which is confined to hh3cOltLaserOnTime.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.5 |
hh3cOltLaserOnTimeMaxValThe upper limit of time which is confined to hh3cOltLaserOnTime.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.6 |
hh3cOltLaserOffTimeMinValThe lower limit of time which is confined to hh3cOltLaserOffTime.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.7 |
hh3cOltLaserOffTimeMaxValThe upper limit of time which is confined to hh3cOltLaserOffTime.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.8 |
hh3cOltDbaDiscoveryLengthMinValThe lower limit of the discovery length which is confined to hh3cOltDbaDiscoveryLength.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.9 |
hh3cOltDbaDiscoveryLengthMaxValThe upper limit of the discovery length which is confined to hh3cOltDbaDiscoveryLength.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.10 |
hh3cOltDbaDiscovryFrequencyMinValThe lower limit of the discovery length which is confined to hh3cOltDbaDiscovryFrequency.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.11 |
hh3cOltDbaDiscovryFrequencyMaxValThe upper limit of the discovery length which is confined to hh3cOltDbaDiscovryFrequency.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.12 |
hh3cOltDbaCycleLengthMinValThe lower limit of the frames which is confined to hh3cOltDbaCycleLength.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.13 |
hh3cOltDbaCycleLengthMaxValThe upper limit of the frames which is confined to hh3cOltDbaCycleLength.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.14 |
hh3cOltPortAlarmLlidMisMinValThe lower limit of the frames which is confined to hh3cOltPortAlarmLlidMismatchThreshold.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.15 |
hh3cOltPortAlarmLlidMisMaxValThe upper limit of the frames which is confined to hh3cOltPortAlarmLlidMismatchThreshold.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.16 |
hh3cOltPortAlarmBerMinValThe lower limit of threshold which is confined to hh3cOltPortAlarmBerThreshold.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.17 |
hh3cOltPortAlarmBerMaxValThe upper limit of threshold which is confined to hh3cOltPortAlarmBerThreshold.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.18 |
hh3cOltPortAlarmFerMinValThe lower limit of threshold which is confined to hh3cOltPortAlarmFerThreshold.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.19 |
hh3cOltPortAlarmFerMaxValThe upper limit of threshold which is confined to hh3cOltPortAlarmFerThreshold.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.20 |
hh3cOnuSilentTableThis table is used for getting silent ONU information of OLT. SEQUENCE OF Hh3cOnuSilentEntry .1.3.6.1.4.1.25506.2.42.1.3.21 |
hh3cOnuSilentEntryThe entry of the table hh3cOnuSilentTable. Hh3cOnuSilentEntry .1.3.6.1.4.1.25506.2.42.1.3.21.1 |
hh3cOnuSilentMacAddrThe MAC address of silent ONUs in OLT. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.21.1.1 |
hh3cOnuSilentTimeThe aging time of a silent ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.21.1.2 |
hh3cOltUsingOnuTableThe table containing configurations to manage ONU interface(s) based on OLT interface. SEQUENCE OF Hh3cOltUsingOnuEntry .1.3.6.1.4.1.25506.2.42.1.3.22 |
hh3cOltUsingOnuEntryThe entry of the table hh3cOltUsingOnuTable. Hh3cOltUsingOnuEntry .1.3.6.1.4.1.25506.2.42.1.3.22.1 |
hh3cOltUsingOnuNumThe ONU interface number. This value is used to specify the ONU interface which the user wants to configure for an OLT interface. Integer32 .1.3.6.1.4.1.25506.2.42.1.3.22.1.1 |
hh3cOltUsingOnuIfIndexThe ifIndex of the ONU interface.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.3.22.1.2 |
hh3cOltUsingOnuRowStatusThis object is responsible for managing the creation, deletion and modification of rows, which supports active status and CreatAndGo, destroy operation.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.3.22.1.3 |
hh3cEponOnuMan OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.5 |
hh3cOnuSysManTableThis table implements the following functions for ONUs: 1. Encrypting all downstream/upstream and downstream directions traffic destined to and originated from a specific LLID (ONU in current implementation). 2. Restart a process of ONU authentication, using the OLT (IEEE 802.1x) authenticator. SEQUENCE OF Hh3cOnuSysManEntry .1.3.6.1.4.1.25506.2.42.1.5.1 |
hh3cOnuSysManEntryThe entry of the table hh3cOnuSysManTable. Hh3cOnuSysManEntry .1.3.6.1.4.1.25506.2.42.1.5.1.1 |
hh3cOnuEncryptManStart encrypting all downstream/upstream and downstream directions traffic destined to and originated from a specific LLID (ONU in current implementation). ONU registration encryption key is used as an initial value. If the encryption key was updated after ONU registration, the last updated key is used. off(1): - Stop encrypting. downlink(2): - Start encrypting all downstream directions traffic. updownlink(3): - Start encrypting all downstream/upstream directions traffic.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.1.1.1 |
hh3cOnuReAuthorizeRestart a process of ONU authentication. If 802.1x authentication is enabled, the OLT (IEEE 802.1x) authenticator is applied. Otherwise, use the default authentication. Until the reauthentication succeeds, the ONU remains its previous authorization mode. The reauthentication process includes a new authentication request sent to the authentication server.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.1.1.2 |
hh3cOnuMulticastFilterStatustrue(1) - Multicast-Filter enable on ONU. false(2) - Multicast-Filter disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.1.1.3 |
hh3cOnuDbaReportQueueSetNumberThe number of queue sets reported in MPCP report frames.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.1.1.4 |
hh3cOnuRemoteFecStatusValue that indicates status of the 1000BASE-PX PHY optional FEC Sublayer for forward error correction see [802.3ah] clause 65.2. enable - enable remote forward error correction. disable - disable remote forward error correction.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.1.1.5 |
hh3cOnuPortBerStatusenable - enable ONU port bit error rate alarm. disable - disable ONU port bit error rate alarm.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.1.1.6 |
hh3cOnuResetReboot ONU.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.1.1.7 |
hh3cOnuMulticastControlModeigmpsnooping - the traditional IGMP snooping mode. multicastcontrol - the specific multicast control mode.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.1.1.8 |
hh3cOnuAccessVlanThe VLAN ID assigned to untagged frames received on ONU.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.1.1.9 |
hh3cOnuEncryptKeyThe encryption key, used to encrypt all downstream traffic destined to and/or upstream traffic originating from a specific ONU. It is a zero length, or MD5 hashed string, by default, the string is empty.rw DisplayString .1.3.6.1.4.1.25506.2.42.1.5.1.1.10 |
hh3cOnuUniUpDownTrapStatustrue - A notification will be sent when UNI link status is change. false - Device will not sent notification when UNI link status is change.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.1.1.11 |
hh3cOnuFecStatusValue that indicates status of the 1000BASE-PX PHY optional FEC Sublayer for forward error correction (include remote onu and local OLT) see [802.3ah] clause 65.2 enable - enable forward error correction. disable - disable forward error correction.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.1.1.12 |
hh3cOnuMcastCtrlHostAgingTimeThe host aging time of multicast control mode on ONU, ranging from 200 to 1000, measured in seconds.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.1.1.13 |
hh3cOnuMulticastFastLeaveEnabletrue(1) - Enable multicast fast leave attribute on all ethernet UNIs of the ONU. false(2) - Disable multicast fast leave attribute on all ethernet UNIs of the ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.1.1.14 |
hh3cOnuPortIsolateEnabletrue(1) - Enable port isolate setting on all ethernet UNIs of the ONU. false(2) - Disable port isolate setting on all ethernet UNIs of the ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.1.1.15 |
hh3cOnuLinkTestTableLLID link test applying to the ONU only including delay measurement option. The command tests a link to a single LLID over a period of time or once, using a variable number of measurement frames. The length of the measurement frames is also parameterized. The test uses a loopback mode of the ONU to return each measurement frame, loopback activation is done using randomly patterned OAM Protocol Data Unit(PDU) frames. SEQUENCE OF Hh3cOnuLinkTestEntry .1.3.6.1.4.1.25506.2.42.1.5.2 |
hh3cOnuLinkTestEntryThe entry of hh3cOnuLinkTestEntry. Hh3cOnuLinkTestEntry .1.3.6.1.4.1.25506.2.42.1.5.2.1 |
hh3cOnuLinkTestFrameNumExact number of measurement frames.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.1 |
hh3cOnuLinkTestFrameSizeMeasurement frames data size, measured in bytes. Not including Preamble, SFD, VLAN tag, and FCS. Frame size minimum value is 56 - if VLAN tag is enabled('VLAN enable' field is set to ENABLE), and 60 - if VLAN tag is disabled. The actual measurement frames sent to the PON are always minimum 60 bytes long. When VLAN tag is enabled, the actual measurement frames size including FCS may reach (1514+4+4=)1522 bytes. 60(60 is VLAN tag disabled) - 1514 .rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.2 |
hh3cOnuLinkTestDelaytrue:Link test includes delay measurement, which corresponds to the difference between sent and received times(including granting delay and firmware processing time overheads). false:Link test not includes a delay measurement.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.2.1.3 |
hh3cOnuLinkTestVlanTagtrue:Enable VLAN tag in link test frames. false:Link test not includes frames with VLAN tag.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.2.1.4 |
hh3cOnuLinkTestVlanPriorityVLAN priority: 0-7.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.5 |
hh3cOnuLinkTestVlanTagIDVLAN ID: 1-4094.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.6 |
hh3cOnuLinkTestResultSentFrameNumThe total number of frames sent during the link test process.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.7 |
hh3cOnuLinkTestResultRetFrameNumThe total number of frames return back during the link test process.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.8 |
hh3cOnuLinkTestResultRetErrFrameNumThe total number of error frames return back during the link test process.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.9 |
hh3cOnuLinkTestResultMinDelayThe minimum delay time in TQ units, which corresponds to the difference between sent and received times (including granting delay and firmware processing time overheads). It's invalid if the field 'hh3cOnuLinkTestDelay' is set to be true.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.10 |
hh3cOnuLinkTestResultMeanDelayThe average delay time in TQ units, which corresponds to the difference between sent and received times (including granting delay and firmware processing time overheads). It's invalid if the field 'hh3cOnuLinkTestDelay' is set to be true.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.11 |
hh3cOnuLinkTestResultMaxDelayThe maximum delay time in TQ units, which corresponds to the difference between sent and received times (including granting delay and firmware processing time overheads). It's invalid if the field 'hh3cOnuLinkTestDelay' is set to be true.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.2.1.12 |
hh3cOnuBandWidthTableSet bandwidth policy parameters(restrictions)for a LLID (only for the ONU). Default policies are set to disable. Policy parameters will be erased upon LLID network disconnection. SEQUENCE OF Hh3cOnuBandWidthEntry .1.3.6.1.4.1.25506.2.42.1.5.3 |
hh3cOnuBandWidthEntryThe entry of table hh3cOnuBandWidthTable. Hh3cOnuBandWidthEntry .1.3.6.1.4.1.25506.2.42.1.5.3.1 |
hh3cOnuDownStreamBandWidthPolicytrue:Enable static bandwidth configuration policing. false:Disable static bandwidth configuration policing.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.3.1.1 |
hh3cOnuDownStreamMaxBandWidthMaximum bandwidth allowed for the ONU, measured in Kbits/Sec.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.3.1.2 |
hh3cOnuDownStreamMaxBurstSizeMaximal number of bytes in a burst. The value is truncated to the nearest smaller 128 bytes multiple value, measured in bytes.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.3.1.3 |
hh3cOnuDownStreamHighPriorityFirsttrue:Enable high priority frames preference. false:Disable high priority frames preference.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.3.1.4 |
hh3cOnuDownStreamShortFrameFirsttrue:Enable short frames preference. false:Disable short frames preference.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.3.1.5 |
hh3cOnuP2PBandWidthPolicytrue:Enable static bandwidth configuration policing. false:Disable static bandwidth configuration policing.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.3.1.6 |
hh3cOnuP2PMaxBandWidthMaximum bandwidth allowed for the ONU, measured in Kbits/Sec.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.3.1.7 |
hh3cOnuP2PMaxBurstSizeMaximal number of bytes in a burst. The value is truncated to the nearest smaller 128 bytes multiple value, measured in bytes.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.3.1.8 |
hh3cOnuP2PHighPriorityFirsttrue:Enable high priority frames preference. false:Disable high priority frames preference.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.3.1.9 |
hh3cOnuP2PShortFrameFirsttrue:Enable short frames preference. false:Disable short frames preference.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.3.1.10 |
hh3cOnuSlaManTableTwo types of DBA algorithm are supported in the ONU. The internal SLA based algorithm is always activated. This table defines the primary parameter about the internal SLA algorithm. SEQUENCE OF Hh3cOnuSlaManEntry .1.3.6.1.4.1.25506.2.42.1.5.4 |
hh3cOnuSlaManEntryThe entry of table hh3cOnuSlaManTable. Hh3cOnuSlaManEntry .1.3.6.1.4.1.25506.2.42.1.5.4.1 |
hh3cOnuSlaMaxBandWidthMaximum bandwidth - measured in Kbit/s. The value of this object should be the multiple of the value of hh3cOnuSlaBandWidthStepVal. The minimum bandwidth should not be larger than the maximum bandwidth.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.4.1.1 |
hh3cOnuSlaMinBandWidthMinimum bandwidth - measured in Kbit/s. The value of this object should be the multiple of the value of hh3cOnuSlaBandWidthStepVal. The maximum bandwidth should be larger than the minimum bandwidth.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.4.1.2 |
hh3cOnuSlaBandWidthStepValGranularity of bandwidth - measured in Kbit/s. The value of hh3cOnuSlaMaxBandWidth and hh3cOnuSlaMinBandWidth should be the multiple of the value of this object.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.4.1.3 |
hh3cOnuSlaDelaylow - low delay. high - high delay. The delay constraint of a specific ONU. Set to high may improve the bandwidth usage at the cost of delay.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.4.1.4 |
hh3cOnuSlaFixedBandWidthFixed bandwidth - measured in Kbit/s. The value of this object should be the multiple of the value of hh3cOnuSlaBandWidthStepVal.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.4.1.5 |
hh3cOnuSlaPriorityClassPrecedence of this flow over others in case of contention. 0 is the lowest priority and 7 is the highest priority.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.4.1.6 |
hh3cOnuSlaFixedPacketSizeFixed packet size - measured in byte. The value of this object should be valid when hh3cOnuSlaFixedBandWidth is configured.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.4.1.7 |
hh3cOnuInfoTablePrimary status of the specified ONU. There will be one row in this table for each information in the system. (1)Software and hardware versions of the specified ONU (hh3cOnuHardMajorVersion, hh3cOnuHardMinorVersion, hh3cOnuUniMacType) (2)Several physical capabilities of the ONU. (hh3cOnuLaserOnTime, hh3cOnuLaserOffTime, hh3cOnuGrantFifoDep.) (3)The operation(activation) status of the ONU. (hh3cOnuWorkMode) SEQUENCE OF Hh3cOnuInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.5 |
hh3cOnuInfoEntryThe entry of the hh3cOnuInfoTable. Hh3cOnuInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.5.1 |
hh3cOnuHardMajorVersionONU hardware major version. If the object length is zero, it means the version is unknown.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.1 |
hh3cOnuHardMinorVersionONU hardware minor version. If the object length is zero, it means the version is unknown.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.2 |
hh3cOnuSoftwareVersionONU software version.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.3 |
hh3cOnuUniMacTypeONU User Network Interface(UNI) port MAC type.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.5.1.4 |
hh3cOnuLaserOnTimeThe ONU laser on time measured in TQ units. If the object value is 0x7FFFFFFF, it means hh3cOnuLaserOnTime is unknown.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.5.1.5 |
hh3cOnuLaserOffTimeThe ONU laser off time measured in TQ units. If the object value is 0x7FFFFFFF, it means hh3cOnuLaserOffTime is unknown.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.5.1.6 |
hh3cOnuGrantFifoDepMaximal number of grant records an ONU can store, relevant to ONU only. range: 1 - 255. 0x7FFFFFFF: unknown value.ro Integer32(1..255|2147483647) .1.3.6.1.4.1.25506.2.42.1.5.5.1.7 |
hh3cOnuWorkModeThe operation(activation) mode of an ONU. other(1) - ONU is in another mode. on(2) - ONU is registered and authorized to the network. In this mode it works as a media converter. pending(3) - ONU has been registered to the PON, but not authorized to the network. off(4) - ONU is not registered to the network.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.5.1.8 |
hh3cOnuPCBVersionONU PCB version.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.9 |
hh3cOnuRttThe signal round-trip-time(RTT) received.ro Unsigned32 .1.3.6.1.4.1.25506.2.42.1.5.5.1.10 |
hh3cOnuEEPROMVersionONU EEPROM version.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.11 |
hh3cOnuRegTypeONU registered type.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.12 |
hh3cOnuHostTypeONU host type.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.13 |
hh3cOnuDistanceThe distance between OLT and ONU, measured in meter.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.5.1.14 |
hh3cOnuLlidThe link layer identifier, which uniquely identifies the ONU of a specific OLT.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.5.1.15 |
hh3cOnuVendorIdONU vendor ID.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.16 |
hh3cOnuFirmwareVersionONU firmware version.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.5.1.17 |
hh3cOnuOpticalPowerReceivedByOltThe burst ONU optical power received by OLT, and when the ONU status is up the value is usable. It measured in 0.01 dBm unit.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.5.1.18 |
hh3cOnuMacAddrInfoTableThis table used for getting MAC address information of ONU. SEQUENCE OF Hh3cOnuMacAddrInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.6 |
hh3cOnuMacAddrInfoEntryThe entry of the hh3cEponOnuMacAddrInfoTable. Hh3cOnuMacAddrInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.6.1 |
hh3cOnuMacIndexThe index of ONUs in one OLT. Integer32 .1.3.6.1.4.1.25506.2.42.1.5.6.1.1 |
hh3cOnuMacAddrFlagThe flag of ONU status. 1 - bound:The ONU is bound but not registered. 2 - registered:The ONU is registered but not bound. 3 - run:The ONU is registered and bound on one OLT. 4 - regIncorrect:The ONU is bound on one OLT and registered on another OLT.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.6.1.2 |
hh3cOnuMacAddressThe MAC address of ONU.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.6.1.3 |
hh3cOnuBindMacAddrTableThis table implements the following functions for ONUs: Bind MAC of ONU. SEQUENCE OF Hh3cOnuBindMacAddrEntry .1.3.6.1.4.1.25506.2.42.1.5.7 |
hh3cOnuBindMacAddrEntryThe entry of the table hh3cOnuBindMacAddrTable. Hh3cOnuBindMacAddrEntry .1.3.6.1.4.1.25506.2.42.1.5.7.1 |
hh3cOnuBindMacAddressBind the MAC of ONU. While the MAC is not bound, the ONU can not go into effect and configurations can not be set. Set 0-0-0 (MAC address) to the EPON device port will unbind the relationship with the original MAC and configurations will be set to default values.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.7.1.1 |
hh3cOnuBindTypeSet the binding type with the ONU which is confined to the index of hh3cEponOnuTypeDescr.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.7.1.2 |
hh3cOnuFirmwareUpdateTableThis table implements the following functions for ONUs: 1. Update the ONU firmware. 2. Result of update ONU firmware. SEQUENCE OF Hh3cOnuFirmwareUpdateEntry .1.3.6.1.4.1.25506.2.42.1.5.8 |
hh3cOnuFirmwareUpdateEntryThe entry of the table hh3cOnuFirmwareUpdateTable. Hh3cOnuFirmwareUpdateEntry .1.3.6.1.4.1.25506.2.42.1.5.8.1 |
hh3cOnuUpdateupdate(1): Update the ONU firmware. Config the MIB object module hh3cEponOnuUpdateFileName with the filename of ONU firmware first.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.8.1.1 |
hh3cOnuUpdateResultThe ONU firmware update result. updating - The ONU is updating firmware right now. ok - The ONU update result is OK. fail - The ONU update result is fail. fileNotExist - The ONU update failed because the file does not exist. notSetFilename - The ONU firmware filename is not set. fileNotMatchONU - The ONU firmware does not match the ONU. timeout - The ONU responses timeout. otherError - The ONU update result is unknown.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.8.1.2 |
hh3cOnuUpdateFileNameThe filename of the ONU firmware to be updated. Note that the filename must contain the file path.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.8.1.3 |
hh3cOnuLinkTestFrameNumMinValThe lower limit of measurement frames which is confined to hh3cOnuLinkTestFrameNum.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.9 |
hh3cOnuLinkTestFrameNumMaxValThe upper limit of measurement frames which is confined to hh3cOnuLinkTestFrameNum.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.10 |
hh3cOnuSlaMaxBandWidthMinValThe lower limit of maximum-bandwidth which is confined to hh3cOnuSlaMaxBandWidth.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.11 |
hh3cOnuSlaMaxBandWidthMaxValThe upper limit of maximum-bandwidth which is confined to hh3cOnuSlaMaxBandWidth.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.12 |
hh3cOnuSlaMinBandWidthMinValThe lower limit of minimum-bandwidth which is confined to hh3cOnuSlaMinBandWidth.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.13 |
hh3cOnuSlaMinBandWidthMaxValThe upper limit of minimum-bandwidth which is confined to hh3cOnuSlaMinBandWidth.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.14 |
hh3cEponOnuTypeManTableThis table is used for getting ONU bind type in current version. SEQUENCE OF Hh3cEponOnuTypeManEntry .1.3.6.1.4.1.25506.2.42.1.5.15 |
hh3cEponOnuTypeManEntryThe entry of the hh3cEponOnuTypeManTable. Hh3cEponOnuTypeManEntry .1.3.6.1.4.1.25506.2.42.1.5.15.1 |
hh3cEponOnuTypeIndexThe ONU type index. Integer32 .1.3.6.1.4.1.25506.2.42.1.5.15.1.1 |
hh3cEponOnuTypeDescrThe ONU type description which can be used to bind ONU in current version. the value of hh3cOnuBindType can be configured by the index of hh3cEponOnuTypeDescr.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.15.1.2 |
hh3cOnuPacketManTableThis table implements the following functions: (1)Manage packet priority trust mode. (2)Manage packet queue-scheduler mode. SEQUENCE OF Hh3cOnuPacketManEntry .1.3.6.1.4.1.25506.2.42.1.5.16 |
hh3cOnuPacketManEntryThe entry of the hh3cOnuPacketManTable. Hh3cOnuPacketManEntry .1.3.6.1.4.1.25506.2.42.1.5.16.1 |
hh3cOnuPriorityTrustThe QOS mode which is assigned on ONU. dscp - The service dscp of politic Priority. ipprecedence - The service IP precedence of politic Priority. cos - The service cos of politic Priority.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.16.1.1 |
hh3cOnuQueueSchedulerThe packet queue-scheduler mode which is assigned on ONU. spq - strict priority queuing. wfq - specifies the weights for weighted round-robin queuing.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.16.1.2 |
hh3cOnuProtocolTableThis table implements the following functions: (1)Manage STP status. (2)Manage IGMP-snooping. (3)Manage DHCP-snooping. SEQUENCE OF Hh3cOnuProtocolEntry .1.3.6.1.4.1.25506.2.42.1.5.17 |
hh3cOnuProtocolEntryThe entry of hh3cOnuProtocolTable. Hh3cOnuProtocolEntry .1.3.6.1.4.1.25506.2.42.1.5.17.1 |
hh3cOnuStpStatustrue(1) - STP status enable on ONU. false(2) - STP status disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.17.1.1 |
hh3cOnuIgmpSnoopingStatustrue(1) - IGMP snooping status enable on ONU. false(2) - IGMP snooping status disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.17.1.2 |
hh3cOnuDhcpsnoopingOption82true(1) - DHCP snooping Option 82 status enable on ONU. false(2) - DHCP snooping Option 82 status disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.17.1.3 |
hh3cOnuDhcpsnoopingtrue(1) - DHCP snooping status enable on ONU. false(2) - DHCP snooping status disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.17.1.4 |
hh3cOnuPppoetrue(1) - PPPOE status enable on ONU. false(2) - PPPOE status disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.17.1.5 |
hh3cOnuIgmpSnoopingHostAgingTSet the host aging time of IGMP on ONU.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.17.1.6 |
hh3cOnuIgmpSnoopingMaxRespTSet the max response time of IGMP on ONU.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.17.1.7 |
hh3cOnuIgmpSnoopingRouterAgingTSet the router aging time of IGMP on ONU.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.17.1.8 |
hh3cOnuIgmpSnoopingAggReportStrue(1) - Igmp snooping aggregation report status enable on ONU. false(2) - Igmp snooping aggregation report status disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.17.1.9 |
hh3cOnuIgmpSnoopingAggLeaveStrue(1) - Igmp snooping aggregation leave status enable on ONU. false(2) - Igmp snooping aggregation leave status disable on ONU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.17.1.10 |
hh3cOnuDot1xTableThis table implements the following functions: (1)Manage 802.1x account. (2)Manage 802.1x password. ONU will be authorized to send and receive frames when the account and the password are all right, otherwise this ONU will be unavailable. SEQUENCE OF Hh3cOnuDot1xEntry .1.3.6.1.4.1.25506.2.42.1.5.18 |
hh3cOnuDot1xEntryThe entry of the hh3cOnuDot1xTable. Hh3cOnuDot1xEntry .1.3.6.1.4.1.25506.2.42.1.5.18.1 |
hh3cOnuDot1xAccountONU 802.1X account. The object value cannot be set as 'a', 'al' or 'all'. The object should be set together with hh3cOnuDot1xPassword.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.18.1.1 |
hh3cOnuDot1xPasswordONU 802.1X password. The object should be set together with hh3cOnuDot1xAccount.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.18.1.2 |
hh3cOnuPriorityQueueTableThis table contains specific information of priority queue. SEQUENCE OF Hh3cOnuPriorityQueueEntry .1.3.6.1.4.1.25506.2.42.1.5.19 |
hh3cOnuPriorityQueueEntryThe entry of hh3cOnuPriorityQueueTable. Hh3cOnuPriorityQueueEntry .1.3.6.1.4.1.25506.2.42.1.5.19.1 |
hh3cOnuQueueDirectionThe direction of priority queue. Enumeration .1.3.6.1.4.1.25506.2.42.1.5.19.1.1 |
hh3cOnuQueueIdThe queue ID of priority queue. Integer32 .1.3.6.1.4.1.25506.2.42.1.5.19.1.2 |
hh3cOnuQueueSizeThe size of priority queue, measured in percent. The total length of all priority queues is a constant, by default, it is assigned to all of the priority queues evenly. The length of each priority queue may be changed by changing the value of hh3cOnuPriorityQueueSize. The total size of the inbound or outbound priority queues should be not more than 100.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.19.1.3 |
hh3cOnuCountTableThis table contains statistics of ONU port. SEQUENCE OF Hh3cOnuCountEntry .1.3.6.1.4.1.25506.2.42.1.5.20 |
hh3cOnuCountEntryThe entry of hh3cOnuCountTable. Hh3cOnuCountEntry .1.3.6.1.4.1.25506.2.42.1.5.20.1 |
hh3cOnuInCRCErrPktsThe total number of frames received with bad CRC checksum.ro Counter64 .1.3.6.1.4.1.25506.2.42.1.5.20.1.1 |
hh3cOnuOutDroppedFramesThe total number of frames dropped because of buffer failure.ro Counter64 .1.3.6.1.4.1.25506.2.42.1.5.20.1.2 |
hh3cEponOnuScalarGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.5.21 |
hh3cOnuPriorityQueueSizeMinValThe lower limit of queue size which is confined to hh3cOnuQueueSize.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.21.1 |
hh3cOnuPriorityQueueSizeMaxValThe upper limit of queue size which is confined to hh3cOnuQueueSize.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.21.2 |
hh3cOnuPriorityQueueBandwidthMinValThe lower limit of hh3cOnuQueueMaxBandwidth.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.21.3 |
hh3cOnuPriorityQueueBandwidthMaxValThe upper limit of hh3cOnuQueueMaxBandwidth.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.21.4 |
hh3cOnuPriorityQueueBurstsizeMinValThe lower limit of hh3cOnuQueueMaxBurstsize.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.21.5 |
hh3cOnuPriorityQueueBurstsizeMaxValThe upper limit of hh3cOnuQueueMaxBurstsize.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.21.6 |
hh3cOnuUpdateByTypeNextIndexOffer a free index of hh3cOnuFirmwareUpdateByTypeTable.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.21.7 |
hh3cOnuQueueBandwidthTableThis table contains specific bandwidth information of ONU priority queue. SEQUENCE OF Hh3cOnuQueueBandwidthEntry .1.3.6.1.4.1.25506.2.42.1.5.22 |
hh3cOnuQueueBandwidthEntryThe entry of hh3cOnuQueueBandwidthTable. Hh3cOnuQueueBandwidthEntry .1.3.6.1.4.1.25506.2.42.1.5.22.1 |
hh3cOnuQueueMaxBandwidthThe maximum bandwidth of specific ONU priority queue, measured in 100Kbps.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.22.1.1 |
hh3cOnuQueueMaxBurstsizeThe maximum burst size of specific ONU priority queue, measured in 64Bytes.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.22.1.2 |
hh3cOnuQueuePolicyStatustrue - enable bandwidth policy false - disable bandwidth policy The bandwidth administrative status of specific ONU priority queue.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.22.1.3 |
hh3cOnuIpAddressTableONU IP address table. SEQUENCE OF Hh3cOnuIpAddressEntry .1.3.6.1.4.1.25506.2.42.1.5.23 |
hh3cOnuIpAddressEntryThe entry of hh3cOnuIpAddressTable. Hh3cOnuIpAddressEntry .1.3.6.1.4.1.25506.2.42.1.5.23.1 |
hh3cOnuIpAddressThe IP address assigned to the ONU.rw IpAddress .1.3.6.1.4.1.25506.2.42.1.5.23.1.1 |
hh3cOnuIpAddressMaskThe mask of IP address denoted by hh3cOnuIpAddress.rw IpAddress .1.3.6.1.4.1.25506.2.42.1.5.23.1.2 |
hh3cOnuIpAddressGatewayThe gateway of IP address denoted by hh3cOnuIpAddress.rw IpAddress .1.3.6.1.4.1.25506.2.42.1.5.23.1.3 |
hh3cOnuDhcpallocatetrue(1) - ONU auto allocate IP address status enable. false(2) - ONU auto allocate IP address status disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.23.1.4 |
hh3cOnuManageVIDThe management VLAN of ONU denoted by hh3cOnuManageVID.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.23.1.5 |
hh3cOnuManageVlanIntfSThe management interface status of ONU denoted by hh3cOnuManageVlanIntfS.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.23.1.6 |
hh3cOnuChipSetInfoTableONU vendor specific information of ONU. SEQUENCE OF Hh3cOnuChipSetInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.24 |
hh3cOnuChipSetInfoEntryThe entry of hh3cOnuChipSetInfoTable. Hh3cOnuChipSetInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.24.1 |
hh3cOnuChipSetVendorIdChipset vendor ID, which identifies the ONU's PON chip vendor according JEDEC ID code.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.24.1.1 |
hh3cOnuChipSetModelChip model, numbering(range from 0 to 0xFF) by the chip vendor.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.24.1.2 |
hh3cOnuChipSetRevisionChip revision.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.24.1.3 |
hh3cOnuChipSetDesignDateChip design date.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.24.1.4 |
hh3cOnuCapabilityTableCapability of ONU. SEQUENCE OF Hh3cOnuCapabilityEntry .1.3.6.1.4.1.25506.2.42.1.5.25 |
hh3cOnuCapabilityEntryThe entry of the table hh3cOnuCapabilityTable. Hh3cOnuCapabilityEntry .1.3.6.1.4.1.25506.2.42.1.5.25.1 |
hh3cOnuServiceSupportedServices types supported by the ONU. These functional groups can be supported independently. geinterfacesupport - supporting (1)/not supporting(0) Gbit Ethernet GE interface. feinterfacesupport - supporting (1)/not supporting(0) 100M Ethernet FE interface.(maximum rate is 100M, without GEinterface) voipservicesupport - supporting (1)/not supporting(0)VoIP service. tdmservicesupport - supporting (1)/not supporting(0)TDM CES service.ro Bits .1.3.6.1.4.1.25506.2.42.1.5.25.1.1 |
hh3cOnuGEPortNumberThe current gigabit ethernet ports number supported by the ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.2 |
hh3cOnuFEPortNumberthe current fast ethernet ports number supported by the ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.3 |
hh3cOnuPOTSPortNumberThe current POTS ports number supported by the ONUro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.4 |
hh3cOnuE1PortsNumberThe current E1 ports number supported by the ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.5 |
hh3cOnuUpstreamQueueNumberThe number of upstream queues supported by the ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.6 |
hh3cOnuMaxUpstreamQueuePerPortThe number of maximum upstream queues per port of the ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.7 |
hh3cOnuDownstreamQueueNumberThe number of downstream queues supported by the ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.8 |
hh3cOnuMaxDownstreamQueuePerPortThe number of maximum downstream queues per port of the ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.25.1.9 |
hh3cOnuBatteryBackuptrue(1) - ONU supports a reserve battery. false(2) - ONU does not support a reserve battery.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.25.1.10 |
hh3cOnuIgspFastLeaveSupportedtrue(1) - ONU supports fast leave in igsp mode. false(2) - ONU does not support fast leave in igsp mode.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.25.1.11 |
hh3cOnuMCtrlFastLeaveSupportedtrue(1) - ONU supports fast leave in multicast control mode. false(2) - ONU does not support fast leave in multicast control mode.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.25.1.12 |
hh3cOnuDbaReportTableThis table defines the information of DBA(dynamic bandwidth allocation) report threshold contained in the MPCP report frames. SEQUENCE OF Hh3cOnuDbaReportEntry .1.3.6.1.4.1.25506.2.42.1.5.26 |
hh3cOnuDbaReportEntryThe entry of the table hh3cOnuDbaReportTable. Hh3cOnuDbaReportEntry .1.3.6.1.4.1.25506.2.42.1.5.26.1 |
hh3cOnuDbaReportQueueIdThe DBA report queue ID. Integer32 .1.3.6.1.4.1.25506.2.42.1.5.26.1.1 |
hh3cOnuDbaReportThresholdThe threshold of the DBA report queue. the following is the queue ID and the related default threshold setting. 1 - 0 2 - 0 3 - 0 4 - 65535 5 - 65535 6 - 0 7 - 0 8 - 0rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.26.1.2 |
hh3cOnuDbaReportStatusenable -threshold configuration is active for the queue. disable -threshold configuration is not active for the queue.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.26.1.3 |
hh3cOnuCosToLocalPrecedenceTableTable of map of the COS to local-precedence. SEQUENCE OF Hh3cOnuCosToLocalPrecedenceEntry .1.3.6.1.4.1.25506.2.42.1.5.27 |
hh3cOnuCosToLocalPrecedenceEntryConfiguration information of map of the COS to local precedence. Hh3cOnuCosToLocalPrecedenceEntry .1.3.6.1.4.1.25506.2.42.1.5.27.1 |
hh3cOnuCosToLocalPrecedenceCosIndexIndex of the map, obtains from packet cos value.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.27.1.1 |
hh3cOnuCosToLocalPrecedenceValueValue of local precedence.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.27.1.2 |
hh3cEponOnuStpPortTableTable of ONU STP ports. SEQUENCE OF Hh3cEponOnuStpPortEntry .1.3.6.1.4.1.25506.2.42.1.5.28 |
hh3cEponOnuStpPortEntryConfiguration information of ONU STP ports. Hh3cEponOnuStpPortEntry .1.3.6.1.4.1.25506.2.42.1.5.28.1 |
hh3cEponStpPortIndexThe index of the STP ports.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.28.1.1 |
hh3cEponStpPortDescrThe description of the STP ports.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.5.28.1.2 |
hh3cEponStpPortStateThe current state of the port (i.e. disabled, discarding, learning and forwarding).ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.28.1.3 |
hh3cOnuPhysicalTableThis table is used for getting ONU physical information. SEQUENCE OF Hh3cOnuPhysicalEntry .1.3.6.1.4.1.25506.2.42.1.5.29 |
hh3cOnuPhysicalEntryThe entry of the hh3cOnuPhysicalTable. Hh3cOnuPhysicalEntry .1.3.6.1.4.1.25506.2.42.1.5.29.1 |
hh3cOnuBridgeMacThe bridge MAC address of ONU.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.29.1.1 |
hh3cOnuFirstPonMacThe MAC address of ONU first PON port.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.29.1.2 |
hh3cOnuFirstPonRegStateThe register state of ONU first PON port.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.29.1.3 |
hh3cOnuSecondPonMacThe MAC address of ONU second PON port.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.29.1.4 |
hh3cOnuSecondPonRegStateThe register state of ONU second PON port.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.29.1.5 |
hh3cOnuSmlkTableThis table is used for getting ONU SMLK information. SEQUENCE OF Hh3cOnuSmlkEntry .1.3.6.1.4.1.25506.2.42.1.5.30 |
hh3cOnuSmlkEntryThe entry of the hh3cOnuSmlkTable. Hh3cOnuSmlkEntry .1.3.6.1.4.1.25506.2.42.1.5.30.1 |
hh3cOnuSmlkGroupIDThe SMLK group ID of ONU.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.30.1.1 |
hh3cOnuSmlkFirstPonRoleThe role of ONU first PON port in a SMLK group.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.30.1.2 |
hh3cOnuSmlkFirstPonStatusThe transmitting status of ONU first PON port in a SMLK group.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.30.1.3 |
hh3cOnuSmlkSecondPonRoleThe role of ONU second PON port in a SMLK group.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.30.1.4 |
hh3cOnuSmlkSecondPonStatusThe transmitting status of ONU second PON port in a SMLK group.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.5.30.1.5 |
hh3cOnuRS485PropertiesTableProperty table. SEQUENCE OF Hh3cOnuRS485PropertiesEntry .1.3.6.1.4.1.25506.2.42.1.5.31 |
hh3cOnuRS485PropertiesEntryThe entry of property table. Hh3cOnuRS485PropertiesEntry .1.3.6.1.4.1.25506.2.42.1.5.31.1 |
hh3cOnuRS485SerialIndexThe index of serial port. Integer32 .1.3.6.1.4.1.25506.2.42.1.5.31.1.1 |
hh3cOnuRS485BaudRateThe port baud rate.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.31.1.2 |
hh3cOnuRS485DataBitsThe port number of data bits in a character.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.31.1.3 |
hh3cOnuRS485ParityThe port sense of a character parity bit.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.31.1.4 |
hh3cOnuRS485StopBitsThe port number of stop bits.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.31.1.5 |
hh3cOnuRS485FlowControlThe port type of input flow control. 'none' indicates no flow control at this level. 'hardware' indicates using hardware signals. 'xonOrxoff' indicates using software function.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.31.1.6 |
hh3cOnuRS485TXOctetsThe number of output octets about the port. The unit is byte.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.31.1.7 |
hh3cOnuRS485RXOctetsThe number of input octets about the port. The unit is byte.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.31.1.8 |
hh3cOnuRS485TXErrOctetsThe number of output error octets about the port. The unit is byte.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.31.1.9 |
hh3cOnuRS485RXErrOctetsThe number of input error octets about the port. The unit is byte.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.31.1.10 |
hh3cOnuRS485ResetStatisticsReset the counters to zero, including hh3cOnuRS485TXOctets, hh3cOnuRS485RXOctets, hh3cOnuRS485TXErrOctets and hh3cOnuRS485RXErrOctets.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.31.1.11 |
hh3cOnuRS485SessionSummaryTableSession summary table. SEQUENCE OF Hh3cOnuRS485SessionSummaryEntry .1.3.6.1.4.1.25506.2.42.1.5.32 |
hh3cOnuRS485SessionSummaryEntryThe entry of session summary table. Hh3cOnuRS485SessionSummaryEntry .1.3.6.1.4.1.25506.2.42.1.5.32.1 |
hh3cOnuRS485SessionMaxNumThe max session number of every serial port which can be supported.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.32.1.1 |
hh3cOnuRS485SessionNextIndexThe next valid index used for creating a new session raw. When there is no valid index left, it will return 0.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.5.32.1.2 |
hh3cOnuRS485SessionTableRS485 raw session table. Data received from RS485 will be sent to the destination by raw sockets. SEQUENCE OF Hh3cOnuRS485SessionEntry .1.3.6.1.4.1.25506.2.42.1.5.33 |
hh3cOnuRS485SessionEntryThe entry of session table. Hh3cOnuRS485SessionEntry .1.3.6.1.4.1.25506.2.42.1.5.33.1 |
hh3cOnuRS485SessionIndexRaw session index. Integer32 .1.3.6.1.4.1.25506.2.42.1.5.33.1.1 |
hh3cOnuRS485SessionTypeThe type of a session. A session can use UDP socket, TCP socket as a client, or TCP socket as a server.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.5.33.1.2 |
hh3cOnuRS485SessionAddTypeThis object indicates the transport type of the address contained in hh3cOnuRS485SessionRemoteIP object.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.2.42.1.5.33.1.3 |
hh3cOnuRS485SessionRemoteIPThe IP of remote landing. When session type is 'udp', this is the peer IP. When session type is 'tcpClient', this is the server IP. When session type is 'tcpServer', this is invalid.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.2.42.1.5.33.1.4 |
hh3cOnuRS485SessionRemotePortThe port of remote landing. When session type is 'udp', this is the peer port. When session type is 'tcpClient', this is the server port. When session type is 'tcpServer', this is invalid.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.33.1.5 |
hh3cOnuRS485SessionLocalPortLocal socket port. When session type is 'udp', this is local UDP socket port. When session type is 'tcpClient', this is invalid. When session type is 'tcpServer', this is the local port which will be listened.rw Integer32 .1.3.6.1.4.1.25506.2.42.1.5.33.1.6 |
hh3cOnuRS485SessionRowStatusThe status used for creating, modifying, and deleting instances of the columnar objects in raw session table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.33.1.7 |
hh3cOnuRS485SessionErrInfoTableError information table. When failed to create a session, error information can be got from this table. SEQUENCE OF Hh3cOnuRS485SessionErrInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.34 |
hh3cOnuRS485SessionErrInfoEntryThe entry of error information table. Hh3cOnuRS485SessionErrInfoEntry .1.3.6.1.4.1.25506.2.42.1.5.34.1 |
hh3cOnuRS485SessionErrInfoError information string. When a response with 'noCreeation' for row creation in table hh3cOnuRS485SessionTable, the error reason can be got from this object.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.5.34.1.1 |
hh3cEponBatchOperationMan OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.6 |
hh3cEponBatchOperationBySlotTableThis table is used for batch operation by slot. SEQUENCE OF Hh3cEponBatchOperationBySlotEntry .1.3.6.1.4.1.25506.2.42.1.6.1 |
hh3cEponBatchOperationBySlotEntryThe entry of the hh3cEponBatchOperationBySlotTable. Hh3cEponBatchOperationBySlotEntry .1.3.6.1.4.1.25506.2.42.1.6.1.1 |
hh3cEponBatchOperationBySlotIndexThe EPON board index. Integer32 .1.3.6.1.4.1.25506.2.42.1.6.1.1.1 |
hh3cEponBatchOperationBySlotTypeThe types of batch operation by slot: 1 - resetUnknown, the object value is not set. 9 - updateDba, update OLT DBA algorithm. Config the MIB object module hh3cEponDbaUpdateFileName. 10 - updateONU, update ONU firmware. Config the MIB object module hh3cEponOnuUpdateFileName with the filename of ONU firmware first.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.6.1.1.2 |
hh3cEponBatchOperationBySlotExecute batch operation.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.6.1.1.3 |
hh3cEponBatchOperationBySlotResultThe result of batch operation. 0xFFFF - other, general error. 1 - working, operation is not completed. 2 - successful, completed successfully. 3 - failed because the DBA source file does not exist. 4 - failed because the ONU firmware file does not exist. 5 - failed because of not set the filename of DBA source. 6 - failed because of not set the filename of ONU firmware. 7 - failed because of not set slottype.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.6.1.1.4 |
hh3cEponBatchOperationByOLTTableThis table is used for batch operation by OLT. SEQUENCE OF Hh3cEponBatchOperationByOLTEntry .1.3.6.1.4.1.25506.2.42.1.6.2 |
hh3cEponBatchOperationByOLTEntryThe entry of the hh3cEponBatchOperationByOLTTable. Hh3cEponBatchOperationByOLTEntry .1.3.6.1.4.1.25506.2.42.1.6.2.1 |
hh3cEponBatchOperationByOLTTypeThe types of batch operation by OLT(operation for all ONUs in the OLT): 1 -- resetUnknown, the object value is not set. 5 -- updateONU, update ONU firmware. configure the MIB object module hh3cEponOnuUpdateFileName with the filename of ONU firmware first.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.6.2.1.1 |
hh3cEponBatchOperationByOLTExecute batch operation.rw Enumeration .1.3.6.1.4.1.25506.2.42.1.6.2.1.2 |
hh3cEponBatchOperationByOLTResultThe result of batch operation: 0xFFFF -- other, gernal error. 1 -- working, operation is not completed. 2 -- successful, operation completed successfully. 4 -- failed because the ONU firmware file does not exist. 6 -- failed because of not set the filename of ONU firmware. 7 -- failed because of not set olttype.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.6.2.1.3 |
hh3cOnuFirmwareUpdateByTypeTableThis table is used to update ONU by ONU type. SEQUENCE OF Hh3cOnuFirmwareUpdateByTypeEntry .1.3.6.1.4.1.25506.2.42.1.6.3 |
hh3cOnuFirmwareUpdateByTypeEntryThe entry of the hh3cOnuFirmwareUpdateByTypeTable. Hh3cOnuFirmwareUpdateByTypeEntry .1.3.6.1.4.1.25506.2.42.1.6.3.1 |
hh3cOnuUpdateByOnuTypeIndexThe type and file relationship table entry index. Integer32 .1.3.6.1.4.1.25506.2.42.1.6.3.1.1 |
hh3cOnuUpdateByTypeOnuTypeThe type of ONUs.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.6.3.1.2 |
hh3cOnuUpdateByTypeFileNameThe file to be updated for the type of ONUs.rw OCTET STRING .1.3.6.1.4.1.25506.2.42.1.6.3.1.3 |
hh3cOnuUpdateByTypeRowStatusThe status of this table entry. Only createAndGo and destroy actions are supported.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.2.42.1.6.3.1.4 |
hh3cEponErrorInfo OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.7 |
hh3cEponSoftwareErrorCodeOLT software error code.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.7.1 |
hh3cOamVendorSpecificAlarmCodeAlarm code of the vendor.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.7.2 |
hh3cEponOnuRegErrorMacAddrThe MAC of ONU registered error.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.7.3 |
hh3cOamEventLogTypeThe type of event that generated this entry in the event log.ro Unsigned32 .1.3.6.1.4.1.25506.2.42.1.7.4 |
hh3cOamEventLogLocationWhether this event occurred locally, or was received from the OAM peer via Ethernet OAM.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.7.5 |
hh3cEponLoopbackPortIndexThe index of port which generate loop back event.ro Integer32 .1.3.6.1.4.1.25506.2.42.1.7.6 |
hh3cEponLoopbackPortDescrA textual string containing information about the port generated loop back event.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.7.7 |
hh3cOltPortAlarmLlidMisFramesthe amount of mismatched frames about the LLID mismatch alarm.ro Unsigned32 .1.3.6.1.4.1.25506.2.42.1.7.8 |
hh3cOltPortAlarmBererror bit rate.ro Unsigned32 .1.3.6.1.4.1.25506.2.42.1.7.9 |
hh3cOltPortAlarmFererror frames rate.ro Unsigned32 .1.3.6.1.4.1.25506.2.42.1.7.10 |
hh3cEponOnuRegSilentMacThe MAC of silent ONU.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.7.11 |
hh3cEponOperationResultThe result of EPON operation.ro OCTET STRING .1.3.6.1.4.1.25506.2.42.1.7.12 |
hh3cEponOnuLaserStateThe state of ONU laser.ro Enumeration .1.3.6.1.4.1.25506.2.42.1.7.13 |
hh3cEponTrap OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.8 |
hh3cEponTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.8.0 |
hh3cEponPortAlarmBerTrapA hh3cEponPortAlarmBerTrap notification is sent when a BER threshold crossing event is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.1 |
hh3cEponPortAlarmFerTrapA hh3cEponPortAlarmFerTrap notification is sent when a frame error rate threshold crossing event is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.2 |
hh3cEponErrorLLIDFrameTrapA hh3cEponErrorLLIDFrameTrap notification is sent when a LLID mismatched frames rate threshold crossing event is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.3 |
hh3cEponLoopBackEnableTrapA hh3cEponLoopBackEnableTrap notification is sent when the loop back command is committed. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.4 |
hh3cEponOnuRegistrationErrTrapA hh3cEponOnuRegistrationErrTrap notification is sent when a ONU register failed. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.5 |
hh3cEponOamDisconnectionTrapA hh3cEponOamDisconnectionTrap notification is sent when LLID's OAM link is disconnected. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.6 |
hh3cEponEncryptionKeyErrTrapA hh3cEponEncryptionKeyErrTrap notification is sent when LLID's encryption key is bad. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.7 |
hh3cEponRemoteStableTrapA hh3cEponRemoteStableTrap notification is sent when remote Data Terminal Equipment(DTE) has not seen or is unsatisfied with local state information. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.8 |
hh3cEponLocalStableTrapA hh3cEponLocalStableTrap notification is sent when DTE has not seen or is unsatisfied with remote state information. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.9 |
hh3cEponOamVendorSpecificTrapA hh3cEponOamVendorSpecificTrap notification is sent when system vendor specific OAM alarm raised. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.10 |
hh3cEponSoftwareErrTrapA hh3cEponSoftwareErrTrap notification is sent when a PAS-SOFT internal error occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.11 |
hh3cEponPortAlarmBerRecoverTrapA hh3cEponPortAlarmBerRecoverTrap notification is sent when a BER threshold crossing event is detected and then recovered. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.12 |
hh3cEponPortAlarmFerRecoverTrapA hh3cEponPortAlarmFerRecoverTrap notification is sent when a frame error rate threshold crossing event is detected and then recoverd. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.13 |
hh3cEponErrorLLIDFrameRecoverTrapA hh3cEponErrorLLIDFrameRecoverTrap notification is sent when a LLID mismatched frames rate threshold crossing event is detected and then recoverd. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.14 |
hh3cEponLoopBackEnableRecoverTrapA hh3cEponLoopBackEnableRecoverTrap notification is sent when the loop back is detected and then recoverd. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.15 |
hh3cEponOnuRegistrationErrRecoverTrapA hh3cEponOnuRegistrationErrRecoverTrap notification is sent when an ONU register failed and then register successful again. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.16 |
hh3cEponOamDisconnectionRecoverTrapA hh3cEponOamDisconnectionRecoverTrap notification is sent when LLID's OAM link is disconnected and then connected. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.17 |
hh3cEponEncryptionKeyErrRecoverTrapA hh3cEponEncryptionKeyErrRecoverTrap notification is sent when LLID's encryption key is bad and then right. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.18 |
hh3cEponRemoteStableRecoverTrapA hh3cEponRemoteStableRecoverTrap notification is sent when remote DTE has not seen or is unsatisfied with local state information and then is realized. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.19 |
hh3cEponLocalStableRecoverTrapA hh3cEponLocalStableRecoverTrap notification is sent when DTE has not seen or is unsatisfied with remote state information and then is realized. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.20 |
hh3cEponOamVendorSpecificRecoverTrapA hh3cEponOamVendorSpecificRecoverTrap notification is sent when system vendor specific OAM alarm is detected and then recovered. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.21 |
hh3cEponSoftwareErrRecoverTrapA hh3cEponSoftwareErrRecoverTrap notification is sent when a PAS-SOFT internal error is detected and then recovered. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.22 |
hh3cDot3OamThresholdRecoverEventA hh3cDot3OamThresholdRecoverEvent notification is sent when hh3cDot3OamThresholdEvent is detected and then recoverd. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.23 |
hh3cDot3OamNonThresholdRecoverEventA hh3cDot3OamNonThresholdRecoverEvent notification is sent when hh3cDot3OamNonThresholdEvent is detected and then recoverd. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.24 |
hh3cEponOnuRegExcessTrapA hh3cEponOnuRegExcessTrap notification is sent when the number of registered ONUs exceeds the limit. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.25 |
hh3cEponOnuRegExcessRecoverTrapA hh3cEponOnuRegExcessRecoverTrap notification is sent when hh3cEponOnuRegExcessTrap is detected and then recoverd. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.26 |
hh3cEponOnuPowerOffTrapA hh3cEponOnuPowerOffTrap notification is sent when ONU is power off. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.27 |
hh3cEponOltSwitchoverTrapA hh3cEponOltSwithoverTrap notification is sent when OLT switchover is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.28 |
hh3cEponOltDFETrapA hh3cEponOltDFETrap notification is sent when there was a serious problem(device fatal error) on OLT. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.29 |
hh3cEponOltDFERecoverTrapA hh3cEponOltDFERecoverTrap notification is sent when device fatal error is detected and then recoverd. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.30 |
hh3cEponOnuSilenceTrapThe hh3cEponOnuSilenceTrap notification is sent when an unbound ONU try to register to an OLT. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.31 |
hh3cEponOnuSilenceRecoverTrapThe hh3cEponOnuSilenceRecoverTrap notification is sent when a silent ONU is bound in the OLT or the aging onu mac address is timeout. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.32 |
hh3cEponOnuUpdateResultTrapA hh3cEponUpdateResultTrap notification is sent when an ONU reported its firmware update result. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.33 |
hh3cEponOnuAutoBindTrapA hh3cEponOnuAutoBindTrap notification is sent when a silent ONU is bound automatically. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.34 |
hh3cEponOnuPortStpStateTrapA hh3cEponOnuPortStpStateTrap notification is sent when a port turns into another state in STP environment. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.35 |
hh3cEponOnuLaserFailedTrapA hh3cEponOnuLaserFailedTrap notification is sent when an ONU has trouble with laser, such as laser constantly turned on, signal degradation or optics EOL (End of Life). NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.36 |
hh3cOnuSmlkSwitchoverTrapA hh3cOnuSmlkSwitchoverTrap notification is sent when an ONU SMLK switchover is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.2.42.1.8.0.37 |
hh3cEponStat OBJECT IDENTIFIER .1.3.6.1.4.1.25506.2.42.1.9 |
hh3cEponStatTableThis table contains line code error statistics of epon port. SEQUENCE OF Hh3cEponStatEntry .1.3.6.1.4.1.25506.2.42.1.9.1 |
hh3cEponStatEntryThe entry of hh3cEponStatTable. Hh3cEponStatEntry .1.3.6.1.4.1.25506.2.42.1.9.1.1 |
hh3cEponStatFERThe frame error rate of epon port, measured in 1e-9 unit.ro Counter64 .1.3.6.1.4.1.25506.2.42.1.9.1.1.1 |
hh3cEponStatBERThe bit error rate of epon port, measured in 1e-9 unit.ro Counter64 .1.3.6.1.4.1.25506.2.42.1.9.1.1.2 |