HDR2-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
75
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
75 total| Object Name |
|---|
usr OBJECT IDENTIFIER .1.3.6.1.4.1.429 |
RFC1213-MIB Unknown .1.3.6.1.4.1.429 |
common OBJECT IDENTIFIER .1.3.6.1.4.1.429.4 |
hdr2 OBJECT IDENTIFIER .1.3.6.1.4.1.429.4.48 |
hdr2Cfg OBJECT IDENTIFIER .1.3.6.1.4.1.429.4.48.1 |
hdr2CfgTableA table containing the configuration parameters for the
Hiper E1/R2 Card. SEQUENCE OF Hdr2CfgEntry .1.3.6.1.4.1.429.4.48.1.1 |
hdr2CfgEntryConfiguration parameters for the E1/R2 module. Hdr2CfgEntry .1.3.6.1.4.1.429.4.48.1.1.1 |
hdr2CfgIndexThe index which uniquely identifies the Hiper E1/R2 CARD to
which this entry is applicable.ro INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.1 |
hdr2CfgRegSigTypeThis object Defines the type of Register Signaling used for
Bit Oriented Signaling.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.2 |
hdr2CfgAnumIdenThis parameter enables or disables the collection of
calling party ( A party or ANI) phone numbers when used
with R2MFC signaling type.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.3 |
hdr2CfgForcedRelIn E1/ R2 ,Forced Release Line signal will be sent only in
case of this parameter is enabled. This signal is
optional.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.4 |
hdr2CfgLastBDigToutThis parameter decides, after how many milliseconds of
silence during the B digit reception, the B party number is
assumed as completed.rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.5 |
hdr2CfgAddrCompleteOn reception of this signal it is assumed that the required
number of B party digits are received. It can hold the
values ranging from A1 to A15. It depends on country
specification.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.6 |
hdr2CfgEndBpartyThis indicates whether I15 is will be received as an
indication for End of B party number or not. If enabled,
at the end of B party number , this I15 signal is received
informing that B party number is completed.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.7 |
hdr2CfgAlawMulawThis object is configuration to apply A Law(E1) or
MuLaw(T1) Companding.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.8 |
hdr2CfgLineSigTypeThis object defines the type of Line Signaling for Bit
Oriented Signaling.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.9 |
hdr2CfgProjIDDepending on this parameter, country dependent or project
dependent parameters are updated. Each and every parameter
has a set of variables to be initialized.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.10 |
hdr2CfgSeizeAckIt defines whether seize acknowledge signal is used or not
for Bit Oriented Signaling.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.11 |
hdr2CfgAnumBnumDuring Bit oriented Register Signaling , after number of B
party ( called party or DNIS) digits have been received,
the A party (calling or ANI) digits are requested ,
provided A party (ANI) request is enabled. Otherwise this
parameter is ignored.rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.12 |
hdr2CfgSubBusyThis object is used in case of subscirber busy.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.13 |
hdr2CfgSndCallingPtyCatgyThis register Signal requests the calling ( A PARTY's )
category.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.14 |
hdr2CfgLineDirectionThis object sets the direction of the channels on the span
line.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.15 |
hdr2CfgPersistentOverrideThis object allows the recieved line signal persistence
(debounce time).rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.16 |
hdr2CfgWrongNumberThis object is the backward register signal used to
indicate that an invalid number has been dialed.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.17 |
hdr2CfgIncomingCpcThis object determines the default calling party category
to be assumed when none is supplied for an incoming call.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.18 |
hdr2CfgRegSigStatusThis object determines whether or not register signalling
is used for incoming and outgoing calls for R2.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.19 |
hdr2CfgUnusedAbcdThis object determines the bit pattern transmitted for
whichever of the ABCD bits are not used for the selected
line signalling scheme. This means CD for R2 Digital and
P7, and BCD for R2 E&M.rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.20 |
hdr2CfgBlkToBlkThis object determines whether or not a blocking signals
received in the idle state is automatically responded to
with a transmitted block signals.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.21 |
hdr2CfgDelayLosThis object determines the required duration of the LOS
state before active calls are dropped and the signalling is
reinitialised. Restoration of signal during this period
allows calls to continue.rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.22 |
hdr2CfgInGlareThis object determines whether the incoming call is
accepted and the outgoing call is dropped in a glare
condition, or both calls are dropped as currently
implemented.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.23 |
hdr2CfgClrCallThis object determines whether an active call is cleared
when an unexpected line signal is received, or the line
signal is ignored as currently implemented.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.24 |
hdr2CfgANumQryThis object determines whether or not an extra MFC cycle is
used before to the A-number to indicate whether an A-number
is available,using III-1 for yes and III-0 for no.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.25 |
hdr2CfgANumNAvTHis object interpret I-12 as A-number not available.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.26 |
hdr2CfgANumReqthis object backward register signal used to request
transmission of the next A-number digit Frequently this is
the same as the signal used to request transmission of the
call category and A-number .rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.27 |
hdr2CfgClrFwdThis object repeatd size/clear-forward sequence is sent to
startup to try to provoke a response from attached
equipment.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.28 |
hdr2CfgRelGuardThis object is duration for which Release Guard signal is
sent.rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.29 |
hdr2CfgPIClrBckThis object determines whether or not a repeated
release/Seize-ack sequence is sent while attempting to
clear anincoming call.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.30 |
hdr2CfgDelayAnsthis object determines the delay between the end of
addressing and transmission of the answer signal.rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.31 |
hdr2CfgBNumLenthis object determines the number of B-number digits to
accept beore sending the 'address complete'signal, provided
the 'end of B_number'signal is not received first.rw INTEGER .1.3.6.1.4.1.429.4.48.1.1.1.32 |
hdr2CfgActBToutthis object determines action to be taken on last B-digit
timeout.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.33 |
hdr2CfgInSubFreethis object backward register signal used to indicate
acceptance of an incoming call.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.34 |
hdr2CfgBNumNFndthis object determines the action on B-Number not found in
teh DNIS handling table.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.35 |
hdr2CfgSndBNumNthis object backward signal requesting retransmission of
curent B-number digit for outgoing calls.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.36 |
hdr2CfgSndBNumN1this object backward signal requesting transmission of
B-number digit N-1 for outgoing calls.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.37 |
hdr2CfgSndBNumN2this object backward signal requesting transimission of
B-number digit N-2 for outgoing calls.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.38 |
hdr2CfgSndBNumN3this object backward signal requesting transimission of
B-number digit N-3 for outgoing calls.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.39 |
hdr2CfgSndFBNumthis object determines whether or not the I-15 'end of
B-number' signal is used for outgoing calls.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.40 |
hdr2CfgDumANumthis object default A-number for outgoing calls in case
none is supplied during call initiation.rw DisplayString .1.3.6.1.4.1.429.4.48.1.1.1.41 |
hdr2CfgEndANumThis object forward register signal used to indicate that
no more a_number digits are avaible.default=iii-15.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.42 |
hdr2CfgOutCatAnalogThis object forward signals used to indicate the call
category for outgoing calls.rw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.43 |
hdr2CfgOutCatDigitalrw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.44 |
hdr2CfgOutCatTestrw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.45 |
hdr2CfgOutCatMaintenancerw Enumeration .1.3.6.1.4.1.429.4.48.1.1.1.46 |
hdr2InCatMap OBJECT IDENTIFIER .1.3.6.1.4.1.429.4.48.2 |
hdr2InCatMapTableA table containing in cat map configurations for the Hiper
E1/R2 Module. SEQUENCE OF Hdr2InCatMapEntry .1.3.6.1.4.1.429.4.48.2.1 |
hdr2InCatMapEntryConfiguration parameters for the E1/R2 module. Hdr2InCatMapEntry .1.3.6.1.4.1.429.4.48.2.1.1 |
hdr2InCatMapIndexThe index which uniquely identifies the Hiper E1/R2 Module
to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.429.4.48.2.1.1.1 |
hdr2InCatMapSigNumThis object is the index for one of 15 possible forward
call category signals for imcoming calls.ro INTEGER .1.3.6.1.4.1.429.4.48.2.1.1.2 |
hdr2InCatMapCallTypeThis object determines the meaning of forward call category
for incoming calls.rw Enumeration .1.3.6.1.4.1.429.4.48.2.1.1.3 |
hdr2Pte OBJECT IDENTIFIER .1.3.6.1.4.1.429.4.48.3 |
hdr2PteTableA table containing the Positron Trap Enable configurations
for the Hiper E1/R2 Module. SEQUENCE OF Hdr2PteEntry .1.3.6.1.4.1.429.4.48.3.1 |
hdr2PteEntryTrap Enable Configuration parameters for the E1/R2 module. Hdr2PteEntry .1.3.6.1.4.1.429.4.48.3.1.1 |
hdr2PteIndexThe index which uniquely identifies the Hiper E1/R2 Module
to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.429.4.48.3.1.1.1 |
hdr2PteMultiFrameEnable the generation of an SNMP trap upon detection of a
Multi-Frame Alignment condition on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.3.1.1.2 |
hdr2PteMultiFrameClrEnable the generation of an SNMP trap upon detection of
clearing a Multi-Frame Alignment condition on the specified
DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.3.1.1.3 |
hdr2PteRemMultiFrameEnable the generation of an SNMP trap upon detection of a
Remote Multi-Frame Alignment condition on the specified
DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.3.1.1.4 |
hdr2PteRemMultiFrameClrEnable the generation of an SNMP trap upon detection of
clearing a Remote Multi-Frame Alignment condition on the
specified DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.3.1.1.5 |
hdr2Te OBJECT IDENTIFIER .1.3.6.1.4.1.429.4.48.4 |
hdr2TeTableA table containing the Trap Enable configurations for the
Hiper E1/R2 Module. SEQUENCE OF Hdr2TeEntry .1.3.6.1.4.1.429.4.48.4.1 |
hdr2TeEntryTrap Enable Configuration parameters for the E1/R2 module. Hdr2TeEntry .1.3.6.1.4.1.429.4.48.4.1.1 |
hdr2TeIndexThe index which uniquely identifies the Hiper E1/R2 CARD to
which this entry is applicable.ro INTEGER .1.3.6.1.4.1.429.4.48.4.1.1.1 |
hdr2TeMultiFrameEnable the generation of an SNMP trap upon detection of a
Multi-Frame Alignment condition on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.4.1.1.2 |
hdr2TeMultiFrameClrEnable the generation of an SNMP trap upon detection of
clearing a Multi-Frame Alignment condition on the specified
DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.4.1.1.3 |
hdr2TeRemMultiFrameEnable the generation of an SNMP trap upon detection of a
Remote Multi-Frame Alignment condition on the specified
DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.4.1.1.4 |
hdr2TeRemMultiFrameClrEnable the generation of an SNMP trap upon detection of
clearing a Remote Multi-Frame Alignment condition on the
specified DS1.rw Enumeration .1.3.6.1.4.1.429.4.48.4.1.1.5 |