H3C-SMLK-MIB
This MIB defines objects for managing Smart Link. Smart Link is a feature developed to address the slow convergence issue with STP. It provides link redundancy and fast convergence in a dual uplink network, allowing the backup link to take over quickly when the primary link fails.
Main OID:
h3cSmlk.1.3.6.1.4.1.2011.10.2.147
29
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
29 total| Object Name |
|---|
h3cSmlkThis MIB defines objects for managing Smart Link. Smart Link is a feature developed to address the slow convergence issue with STP. It provides link redundancy and fast convergence in a dual uplink network, allowing the backup link to take over quickly when the primary link fails. MODULE-IDENTITY .1.3.6.1.4.1.2011.10.2.147 |
h3cSmlkObject OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.147.1 |
h3cSmlkGroupTableA list of entries of a smart link group. SEQUENCE OF H3cSmlkGroupEntry .1.3.6.1.4.1.2011.10.2.147.1.1 |
h3cSmlkGroupEntryA list of parameters that describe a smart link group. H3cSmlkGroupEntry .1.3.6.1.4.1.2011.10.2.147.1.1.1 |
h3cSmlkGroupIDAn index that uniquely identifies an entry in the smart link group table.ro Integer32 .1.3.6.1.4.1.2011.10.2.147.1.1.1.1 |
h3cSmlkDeviceIDDevice ID of a smart link group. The device ID is the bridge MAC of the device.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.147.1.1.1.2 |
h3cSmlkPreemptionModePreemption mode of a smart link group.rw Enumeration .1.3.6.1.4.1.2011.10.2.147.1.1.1.3 |
h3cSmlkSpeedThresholdSpeed threshold for a smart link group in speed mode. This object is valid only when the value of h3cSmlkPreemptionMode is 'speed'.rw Integer32 .1.3.6.1.4.1.2011.10.2.147.1.1.1.4 |
h3cSmlkPreemptionDelayPreemption delay for a smart link group, in the range of 0 to 300 seconds.rw Integer32 .1.3.6.1.4.1.2011.10.2.147.1.1.1.5 |
h3cSmlkControlVlanIDIndex of the control VLAN specified for a smart link group. The value 65535 indicates that the control VLAN has not been configured.rw Integer32 (1..4094|65535) .1.3.6.1.4.1.2011.10.2.147.1.1.1.6 |
h3cSmlkInstanceListLowEach octet contained in this value specifies an eight-instance group, with the first octet specifying instances 0 through 7, the second octet specifying instances 8 through 15, and so on. Within each octet, the most significant bit represents the highest numbered instance, and the least significant bit represents the lowest numbered instance. Each instance to which the protected VLANs of a smart link group are mapped corresponds to a bit within the value of this object. A bit with a value of '1' indicates that the VLANs mapped to the instance are protected VLANs of the smart link group. The VLANs mapped to the instance are not protected VLANs if the corresponding bit has a value of '0'. The value of this object must be set with h3cSmlkInstanceListHigh at the same time when a SET operation is performed.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.147.1.1.1.7 |
h3cSmlkInstanceListHighEach octet contained in this value specifies an eight-instance group, with the first octet specifying instances 2048 through 2055, the second octet specifying instances 2056 through 2063, and so on. Within each octet, the most significant bit represents the highest numbered instance, and the least significant bit represents the lowest numbered instance. The most significant bit of the last octet is invalid. Each instance to which the protected VLANs of a smart link group are mapped corresponds to a bit within the value of this object. A bit with a value of '1' indicates that the VLANs mapped to the instance are protected VLANs of the smart link group. The VLANs mapped to the instance are not protected VLANs if the corresponding bit has a value of '0'. The value of this object must be set with h3cSmlkInstanceListLow at the same time when a SET operation is performed.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.147.1.1.1.8 |
h3cSmlkGroupRowStatusThis object is responsible for managing creation, deletion, and modification of rows. The rows support active status, CreatAndGo, and destroy operations.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.147.1.1.1.9 |
h3cSmlkPortTableA list of port entries of a smart link group. SEQUENCE OF H3cSmlkPortEntry .1.3.6.1.4.1.2011.10.2.147.1.2 |
h3cSmlkPortEntryA list of parameters that describe a port to be added to a smart link group. H3cSmlkPortEntry .1.3.6.1.4.1.2011.10.2.147.1.2.1 |
h3cSmlkPortIfIndexIfIndex of a port in a smart link group.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.10.2.147.1.2.1.1 |
h3cSmlkPortRoleRole of a port in a smart link group.rw Enumeration .1.3.6.1.4.1.2011.10.2.147.1.2.1.2 |
h3cSmlkPortStatusStatus of a port in a smart link group.ro Enumeration .1.3.6.1.4.1.2011.10.2.147.1.2.1.3 |
h3cSmlkFlushCountNumber of transmitted flush messages.ro Counter64 .1.3.6.1.4.1.2011.10.2.147.1.2.1.4 |
h3cSmlkLastFlushTimeTime when the last flush message was transmitted.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.147.1.2.1.5 |
h3cSmlkPortRowStatusThis object is responsible for managing creation, deletion, and modification of rows. The rows support active status, CreatAndGo, and destroy operations.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.147.1.2.1.6 |
h3cSmlkFlushEnableTableA list of ports on which flush message receiving is enabled. SEQUENCE OF H3cSmlkFlushEnableEntry .1.3.6.1.4.1.2011.10.2.147.1.3 |
h3cSmlkFlushEnableEntryA list of parameters that describe a port on which flush message receiving is enabled. H3cSmlkFlushEnableEntry .1.3.6.1.4.1.2011.10.2.147.1.3.1 |
h3cSmlkIfIndexIfIndex of a port on which flush message receiving is enabled. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.10.2.147.1.3.1.1 |
h3cSmlkControlVlanListLowSpecifies the control VLANs used for receiving flush messages. The VLAN ID range, described by bitmap, is from 1 to 2048. The length of bitmap is 256 in bytes. Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, and so on. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.147.1.3.1.2 |
h3cSmlkControlVlanListHighSpecifies the control VLANs used for receiving flush messages. The VLAN ID range, described by bitmap, is from 2049 to 4094. The length of bitmap is 256 in bytes. Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, and so on. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.147.1.3.1.3 |
h3cSmlkTrap OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.147.2 |
h3cSmlkTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.147.2.0 |
h3cSmlkGroupLinkActiveA trap message is generated when the status of a port in a smart link group changes to active. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.147.2.0.1 |