H3C-DOT11-SA-MIB
AI MIB Summary
The H3C-DOT11-SA-MIB enables monitoring of RF spectrum analysis metrics on H3C Access Points to detect and classify non-Wi-Fi interference sources, channel quality degradation, and contention-induced packet transmission issues.
This MIB module provides spectrum analysis information. The initial revision of this MIB module. The spectrum analysis module on APs is able to examine the radio frequency (RF) environment in which the Wi-Fi network is operating, identify interference and classify its sources. An analysis of the results can then be used to quickly isolate issues with packet transmission, channel quality, and traffic congestion caused by contention with other devices operating in the same band or channel.
Main OID:
h3cDot11Sa.1.3.6.1.4.1.2011.10.2.75.13
61
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
61 total| Object Name |
|---|
h3cDot11SaThis MIB module provides spectrum analysis information. The initial revision of this MIB module. The spectrum analysis module on APs is able to examine the radio frequency (RF) environment in which the Wi-Fi network is operating, identify interference and classify its sources. An analysis of the results can then be used to quickly isolate issues with packet transmission, channel quality, and traffic congestion caused by contention with other devices operating in the same band or channel. MODULE-IDENTITY .1.3.6.1.4.1.2011.10.2.75.13 |
h3cDot11SaCfgGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.13.1 |
h3cDot11SaCfgTableThis table is used to configure spectrum analysis. SEQUENCE OF H3cDot11SaCfgEntry .1.3.6.1.4.1.2011.10.2.75.13.1.1 |
h3cDot11SaCfgEntryThis entry contains the spectrum analysis configuration. H3cDot11SaCfgEntry .1.3.6.1.4.1.2011.10.2.75.13.1.1.1 |
h3cDot11SaCfgRadioTypeRepresents the radio type of the configuration. Enumeration .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.1 |
h3cDot11SaEnableRepresents whether spectrum analysis is enabled globally.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.2 |
h3cDot11SaRptDevTypeRepresents which types of interference devices should be reported.rw Bits .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.3 |
h3cDot11SaTrapDevEnableRepresents whether the interference device trap is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.4 |
h3cDot11SaTrapDevTypeRepresents which types of interference device will send traps when the interference device trap is enabled.rw Bits .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.5 |
h3cDot11SaTrapAQEnableRepresents whether the air quality trap is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.6 |
h3cDot11SaTrapAQThresholdRepresents the air quality trap threshold. When the air quality is below this value, the air quality trap will be sent.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.7 |
h3cDot11SaDrivenRRMEnableConfigure whether to trigger RRM to run when an access point detects a certain level of interference.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.8 |
h3cDot11SaDrivenRRMSntConfigure the threshold at which RRM will be triggered. When the interference level for the access point rises above the threshold level, RRM initiates a local dynamic channel assignment (DCA) run and changes the channel of the affected access point radio if possible to improve network performance. Low represents a decreased sensitivity to changes in the environment while high represents an increased sensitivity.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.13.1.1.1.9 |
h3cDot11SaStatusGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.13.2 |
h3cDot11SaRtFFTDataTableThis table contains the real-time FFT data for spectrum analysis. SEQUENCE OF H3cDot11SaRtFFTDataEntry .1.3.6.1.4.1.2011.10.2.75.13.2.1 |
h3cDot11SaRtFFTDataEntryThis entry contains the real-time FFT data for spectrum analysis. H3cDot11SaRtFFTDataEntry .1.3.6.1.4.1.2011.10.2.75.13.2.1.1 |
h3cDot11SaAPIDRepresents the serial ID of the AP. H3cDot11ObjectIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.1 |
h3cDot11SaRadioIDRepresents the ID of the radio. H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.2 |
h3cDot11SaRtDataGroupIDRepresents group ID of the collected data. Maybe the device collects multiple groups of data at the collected interval. Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.3 |
h3cDot11SaFrequencyRepresents the frequency number in 100 Hz. Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.4 |
h3cDot11SaRtFreqPowerRepresents the power of the frequency point.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.5 |
h3cDot11SaRtFreqMaxPowerRepresents the max power of the frequency point.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.6 |
h3cDot11SaRtFreqDutyCycleRepresents the duty cycle of the frequency point.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.7 |
h3cDot11SaRtFreqDataSeqNoRepresents the sequence number of the data.ro Unsigned32 .1.3.6.1.4.1.2011.10.2.75.13.2.1.1.8 |
h3cDot11SaIntfDevTableThis table contains the information of the interfering devices. SEQUENCE OF H3cDot11SaIntfDevEntry .1.3.6.1.4.1.2011.10.2.75.13.2.2 |
h3cDot11SaIntfDevEntryThis entry contains the information of the interfering devices. H3cDot11SaIntfDevEntry .1.3.6.1.4.1.2011.10.2.75.13.2.2.1 |
h3cDot11SaDevIDRepresents the device identification number that uniquely identified the interfering device. Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.2.1.1 |
h3cDot11SaDevTypeRepresents type of the interferer.ro H3cDot11SaIntfDevType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.2.2.1.2 |
h3cDot11SaDevSIRepresents severity index of the interfering device. Severity index is calculated, a positive integer between 0 and 100(with 100 being the most severe).ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.2.1.3 |
h3cDot11SaDevRSSIRepresents receive signal strength indicator (RSSI) of interfering device.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.2.1.4 |
h3cDot11SaDevDutyCycleRepresents proportion of time in percentage during which the interfering device was active.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.2.1.5 |
h3cDot11SaDevAffectedChlsRepresents channels that the interfering device affects.ro OCTET STRING .1.3.6.1.4.1.2011.10.2.75.13.2.2.1.6 |
h3cDot11SaDevDetectedTimeRepresents time at which the interference was detected.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.13.2.2.1.7 |
h3cDot11SaAirQualityTableThis table contains the air quality of the channels. SEQUENCE OF H3cDot11SaAirQualityEntry .1.3.6.1.4.1.2011.10.2.75.13.2.3 |
h3cDot11SaAirQualityEntryThis entry contains the air quality of the channels. H3cDot11SaAirQualityEntry .1.3.6.1.4.1.2011.10.2.75.13.2.3.1 |
h3cDot11SaChlNumRepresents the radio channel where the air quality is monitored. H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.2.3.1.1 |
h3cDot11SaAvgQualityRepresents the average air quality for this radio channel.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.3.1.2 |
h3cDot11SaMinQualityRepresents the minimum air quality for this radio channel.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.3.1.3 |
h3cDot11SaIntfDevNumRepresents the number of interferers detected by the radios on the 802.11a/n or 802.11b/g/n radio band.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.3.1.4 |
h3cDot11SaWiFiUtilRepresents the percentage of the channel currently being used by Wi-Fi devices.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.3.1.5 |
h3cDot11SaNonWiFiUtilRepresents the percentage of the channel currently being used by non-Wi-Fi interference.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.3.1.6 |
h3cDot11SaNoiseFloorRepresents current noise floor recorded on the channel.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.2.3.1.7 |
h3cDot11SaNotifyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.13.3 |
h3cDot11SaTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.13.3.0 |
h3cDot11SaIntfDevDetectedInterfering device is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.13.3.0.1 |
h3cDot11SaIntfDevDisappearInterfering device disappeared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.13.3.0.2 |
h3cDot11SaChlQltLowThe quality of the channel is below the specified threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.13.3.0.3 |
h3cDot11SaChlQltRecoverThe quality of the channel recovered from low status. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.13.3.0.4 |
h3cDot11SaTrapVars OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.13.3.1 |
h3cDot11SaTrapAPIDRepresents the identifier of the AP.ro H3cDot11ObjectIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.3.1.1 |
h3cDot11SaTrapRadioIDRepresents the identifier of the radio.ro H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.3.1.2 |
h3cDot11SaTrapDevIDRepresents the device identification number that uniquely identified the interfering device.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.3.1.3 |
h3cDot11SaTrapIntfDevTypeRepresents type of the interferer.ro H3cDot11SaIntfDevType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.3.1.4 |
h3cDot11APTrapDevSIRepresents severity index of the interfering device. Severity index is calculated, a positive integer between 0 and 100(with 100 being the most severe).ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.3.1.5 |
h3cDot11SaTrapDevRSSIRepresents receive signal strength indicator (RSSI) of interfering device.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.3.1.6 |
h3cDot11APTrapDevDCRepresents proportion of time in percentage during which the interfering device was active.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.3.1.7 |
h3cDot11APTrapDevChlsRepresents channels that the interfering device affects.ro OCTET STRING .1.3.6.1.4.1.2011.10.2.75.13.3.1.8 |
h3cDot11APTrapDevDctTimeRepresents time at which the interference was detected.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.13.3.1.9 |
h3cDot11SaTrapChlNumRepresents the radio channel where the air quality is monitored.ro H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.13.3.1.10 |
h3cDot11SaTrapChlQltRepresents the quality for this radio channel.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.3.1.11 |
h3cDot11SaTrapChlIntfNumRepresents the number of interferers detected by the radios on the 802.11a/n or 802.11b/g/n radio band.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.13.3.1.12 |