H3C-DOT11-RRM-MIB
This MIB file is to provide the object definition of WLAN radio resource management (RRM).
Main OID:
h3cDot11RRM.1.3.6.1.4.1.2011.10.2.75.8
110
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
110 total| Object Name |
|---|
h3cDot11RRMThis MIB file is to provide the object definition of WLAN radio resource management (RRM). MODULE-IDENTITY .1.3.6.1.4.1.2011.10.2.75.8 |
h3cDot11RRMConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.1 |
h3cDot11RRMGlobalCfgPara OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.1.1 |
h3cDot11RRM11nMadtMaxMcsSpecify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.rw Integer32 (0..76 | 255) .1.3.6.1.4.1.2011.10.2.75.8.1.1.1 |
h3cDot11RRM11nSuptMaxMcsSpecify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.1.2 |
h3cDot11RRM11gProtectEnable/Disable dot11g protection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.1.1.3 |
h3cDot11RRM11aPwrConstrtConfigure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of power constraint is 0 to MAX-POWER-1 (where the MAX-POWER is defined by the regulatory domain).rw Integer32 UNITS "dBm" .1.3.6.1.4.1.2011.10.2.75.8.1.1.4 |
h3cDot11RRM11aSpectrumManagEnable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and power constraints applicable to all devices in the BSS based on regulatory domain specification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.1.1.5 |
h3cDot11RRMAutoChlAvoid11hConfigure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel selection and one of them is selected.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.1.1.6 |
h3cDot11RRMScanChlSet the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the radio band are scanned.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.8.1.1.7 |
h3cDot11RRMScanRptIntvelSet the scan report interval.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.1.8 |
h3cDot11APInterfNumThreshhdRepresents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node is zero, AP interference trap will be sent immediately.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.1.9 |
h3cDot11StaInterfNumThreshhdRepresents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this node is zero, STA interference trap will be sent immediately.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.1.10 |
h3cDot11RRMRadioCfgTableConfigure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time. SEQUENCE OF H3cDot11RRMRadioCfgEntry .1.3.6.1.4.1.2011.10.2.75.8.1.2 |
h3cDot11RRMRadioCfgEntryConfigure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time. H3cDot11RRMRadioCfgEntry .1.3.6.1.4.1.2011.10.2.75.8.1.2.1 |
h3cDot11RRMRadioType802.11 radio type. H3cDot11RadioType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.1 |
h3cDot11RRMCfgChlStateEnable/Disable dynamic channel selection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.2 |
h3cDot11RRMCfgChlModeConfigure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.3 |
h3cDot11RRMChlProntoRadioElmtSpecify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of channel selection control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.4 |
h3cDot11RRMCfgPwrStateEnable/Disable dynamic power selection for the band.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.5 |
h3cDot11RRMCfgPwrModeConfigure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.6 |
h3cDot11RRMPwrProntoRadioElmtSpecify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of transmit power control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.7 |
h3cDot11RRMCfgIntrvlConfigure the calibration interval.rw Integer32 UNITS "minute" .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.8 |
h3cDot11RRMCfgIntrfThresConfigure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.9 |
h3cDot11RRMCfgNoiseThresConfigure the noise threshold.rw Integer32 (-127..127) .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.10 |
h3cDot11RRMCfgPERThresConfigure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.11 |
h3cDot11RRMCfgToleranceFctrConfigure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interference and packet error rate than those specified by the user.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.12 |
h3cDot11RRMCfgAdjacencyFctrConfigure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value n is the adjacency factor.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.2.1.13 |
h3cDot11RRMAPCfgTableThis table defines the RRM parameters for AP. SEQUENCE OF H3cDot11RRMAPCfgEntry .1.3.6.1.4.1.2011.10.2.75.8.1.3 |
h3cDot11RRMAPCfgEntryEach entry contains information of RRM parameters for AP. H3cDot11RRMAPCfgEntry .1.3.6.1.4.1.2011.10.2.75.8.1.3.1 |
h3cDot11RRMAPWorkModeAP work mode.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.8.1.3.1.1 |
h3cDot11RRMSDRadioGroupTableThis table defines RRM self-decisive radio group. SEQUENCE OF H3cDot11RRMSDRadioGroupEntry .1.3.6.1.4.1.2011.10.2.75.8.1.4 |
h3cDot11RRMSDRadioGroupEntryEach entry contains information of one RRM self-decisive radio group. H3cDot11RRMSDRadioGroupEntry .1.3.6.1.4.1.2011.10.2.75.8.1.4.1 |
h3cDot11RRMSDRadioGroupIdRepresents RRM self-decisive radio group ID. Unsigned32 .1.3.6.1.4.1.2011.10.2.75.8.1.4.1.1 |
h3cDot11RRMSDRadioGroupDescRepresents the description of RRM self-decisive radio group.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.8.1.4.1.2 |
h3cDot11RRMSDRdGrpChlHolddownTmRepresents the channel holddown time of RRM self-decisive radio group.rw Unsigned32 UNITS "minute" .1.3.6.1.4.1.2011.10.2.75.8.1.4.1.3 |
h3cDot11RRMSDRdGrpPwrHolddownTmRepresents the power holddown time of RRM self-decisive radio group.rw Unsigned32 UNITS "minute" .1.3.6.1.4.1.2011.10.2.75.8.1.4.1.4 |
h3cDot11RRMSDRdGroupRowStatusThe row status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.1.4.1.5 |
h3cDot11RRMAPCfg2TableThis table defines the RRM parameters for AP. SEQUENCE OF H3cDot11RRMAPCfg2Entry .1.3.6.1.4.1.2011.10.2.75.8.1.5 |
h3cDot11RRMAPCfg2EntryEach entry contains information of RRM parameters for AP. H3cDot11RRMAPCfg2Entry .1.3.6.1.4.1.2011.10.2.75.8.1.5.1 |
h3cDot11RRMAPSerialIDSerial ID of the AP. H3cDot11ObjectIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.1.5.1.1 |
h3cDot11RRMAPIntfThresholdRepresents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.5.1.2 |
h3cDot11RRMStaIntfThresholdRepresents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.8.1.5.1.3 |
h3cDot11RRMCoChlIntfTrapThhdRepresents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.8.1.5.1.4 |
h3cDot11RRMAdjChlIntfTrapThhdRepresents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.8.1.5.1.5 |
h3cDot11RRMDetectGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.2 |
h3cDot11RRMChlRptTableThis table shows the RRM channel information of each radio on all APs. SEQUENCE OF H3cDot11RRMChlRptEntry .1.3.6.1.4.1.2011.10.2.75.8.2.1 |
h3cDot11RRMChlRptEntryEach entry contains information of RRM channel information of the radio on the AP. H3cDot11RRMChlRptEntry .1.3.6.1.4.1.2011.10.2.75.8.2.1.1 |
h3cDot11RRMRadioIndexRepresents index of the radio.ro H3cDot11RadioElementIndex (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.1 |
h3cDot11RRMChlRptChlNumChannel number.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.2 |
h3cDot11RRMChlRptChlTypeChannel type.ro Enumeration .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.3 |
h3cDot11RRMChlRptChlQltyChannel quality.ro Enumeration .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.4 |
h3cDot11RRMChlRptNbrCntNumber of neighbors found on the channel.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.5 |
h3cDot11RRMChlRptLoadLoad observed on the channel in percentage.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.6 |
h3cDot11RRMChlRptUtlzUtilization of the channel in percentage.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.7 |
h3cDot11RRMChlRptIntrfInterference observed on the channel in percentage.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.8 |
h3cDot11RRMChlRptPERPacket error rate observed on the channel in percentage.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.9 |
h3cDot11RRMChlRptRetryRatePercentage of retransmission happened on the channel.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.10 |
h3cDot11RRMChlRptNoiseNoise observed on the channel.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.11 |
h3cDot11RRMChlRptRadarIndtcrRadar detection status.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.8.2.1.1.12 |
h3cDot11RRMNbrInfoTableThis table shows the RRM neighbor information of each radio on all APs. SEQUENCE OF H3cDot11RRMNbrInfoEntry .1.3.6.1.4.1.2011.10.2.75.8.2.2 |
h3cDot11RRMNbrInfoEntryEach entry contains information of RRM neighbor information of the radio on an AP. H3cDot11RRMNbrInfoEntry .1.3.6.1.4.1.2011.10.2.75.8.2.2.1 |
h3cDot11RrmNbrBSSIDMAC address of the AP. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.2.2.1.1 |
h3cDot11RrmNbrChlChannel number on which the neighbor was found.ro H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.2.2.1.2 |
h3cDot11RRMNbrIntrfInterference observed on the channel in percentage by neighbor.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.2.1.3 |
h3cDot11RrmNbrRSSISignal strength of the AP in dBm.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.2011.10.2.75.8.2.2.1.4 |
h3cDot11RrmNbrTypeType of the AP, managed or unmanaged.ro Enumeration .1.3.6.1.4.1.2011.10.2.75.8.2.2.1.5 |
h3cDot11RrmNbrSSIDSSID of the Neighbor.ro H3cDot11SSIDStringType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.2.2.1.6 |
h3cDot11RRMHistoryTableThis table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the channel, power, interference parameters. SEQUENCE OF H3cDot11RRMHistoryEntry .1.3.6.1.4.1.2011.10.2.75.8.2.3 |
h3cDot11RRMHistoryEntryEach entry shows the details of channel and power changes. H3cDot11RRMHistoryEntry .1.3.6.1.4.1.2011.10.2.75.8.2.3.1 |
h3cDot11RRMHistoryIdHistory number of the change. Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.1 |
h3cDot11RRMHistoryRecIndctrHistory record type of the change. Enumeration .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.2 |
h3cDot11RRMHistoryChlChannel on which the radio operates before/after the change of channel or power.ro H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.3 |
h3cDot11RRMHistoryPwrPower of the radio before/after the change of channel or power.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.4 |
h3cDot11RRMHistoryLoadLoad observed on the radio in percentage before/after the change of channel or power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.5 |
h3cDot11RRMHistoryUtlzUtilization of the radio in percentage before/after the change of channel or power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.6 |
h3cDot11RRMHistoryIntrfInterference observed on the radio in percentage before/after the change of channel or power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.7 |
h3cDot11RRMHistoryNoiseNoise observed on the radio before/after the change of channel or power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.8 |
h3cDot11RRMHistoryPERPacket error rate observed on the radio in percentage before/after the change of channel or power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.9 |
h3cDot11RRMHistoryRetryRatePercentage of retransmission happened on the radio before/after the change of channel or power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.10 |
h3cDot11RRMHistoryChgReasonReason for the change of channel or power. The various bit positions are: |0 |Others | |1 |Coverage | |2 |Radar | |3 |Retransmission | |4 |Packets discarded | |5 |Interference | 0 is returned when the history record type is after.ro Bits .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.11 |
h3cDot11RRMHistoryChgDateTimeThe time when the channel or power change occurred.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.2.3.1.12 |
h3cDot11RRMNotifyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.3 |
h3cDot11RRMChlQltyNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.3.1 |
h3cDot11RRMChlQltyNtfPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.3.1.0 |
h3cDot11RRMIntrfLimitThis notification will be sent when interference on the radio exceeds the limit. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.8.3.1.0.1 |
h3cDot11RRMPERLimitThis notification will be sent when packet error rate on the radio exceeds the limit. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.8.3.1.0.2 |
h3cDot11RRMNoiseLimitThis notification will be sent when noise on the radio exceeds the limit. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.8.3.1.0.3 |
h3cDot11RRMResChgNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.3.2 |
h3cDot11RRMResChgNtfPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.3.2.0 |
h3cDot11RRMPowerChangeThis notification will be sent when power changed on the radio automatically. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.8.3.2.0.1 |
h3cDot11RRMNotificationsVar OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.3.3 |
h3cDot11NewPowerPower of the radio after the change of power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.3.3.1 |
h3cDot11OldPowerPower of the radio before the change of power.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.3.3.2 |
h3cDot11MonitorDetectedGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.8.4 |
h3cDot11MonitorDetectedDevTableThis table shows the devices of AP detected SEQUENCE OF H3cDot11MonitorDetectedDevEntry .1.3.6.1.4.1.2011.10.2.75.8.4.1 |
h3cDot11MonitorDetectedDevEntryEach entry contains information of detected devices. H3cDot11MonitorDetectedDevEntry .1.3.6.1.4.1.2011.10.2.75.8.4.1.1 |
h3cDot11MonitorDevMACRepresents MAC address of the device detected. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.1 |
h3cDot11MonitorDevTypeRepresents type of the device detected.ro Enumeration .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.2 |
h3cDot11MonitorDevVendorRepresents vendor of the detected device.ro OCTET STRING .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.3 |
h3cDot11MonitorDevSSIDRepresents the service set identifier for the ESS of the device which type is ap or adhoc.ro OCTET STRING .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.4 |
h3cDot11MonitorDevBSSIDRepresents the basic service set identifier of the detected device.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.5 |
h3cDot11MonitorDevChannelRepresents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is interference between adjacent channels.ro H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.6 |
h3cDot11MonitorRadioIdRepresents the radio ID of the AP that detected the device.ro H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.7 |
h3cDot11MonitorDevMaxRSSIRepresents the maximum detected RSSI of the device in a scan report cycle.ro Integer32 UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.8 |
h3cDot11MonitorDevBeaconIntvlRepresents the beacon interval for the detected device(not include the device which type is client).ro Integer32 UNITS "millisecond" .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.9 |
h3cDot11MonitorDevFstDctTimeRepresents the time at which the device was first detected.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.10 |
h3cDot11MonitorDevLstDctTimeRepresents the time at which the device was detected last time.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.11 |
h3cDot11MonitorDevClearThis object is used to clear the information of the device detected in the WLAN. It will return false for get operation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.12 |
h3cDot11MonitorDevSNRRepresents the SNR of the device in a scan report cycle.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.8.4.1.1.13 |