GDCDSX1-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
129
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
129 total| Object Name |
|---|
gdc OBJECT IDENTIFIER .1.3.6.1.4.1.498 |
RFC1155-SMI Unknown .1.3.6.1.4.1.498 |
dsx1 OBJECT IDENTIFIER .1.3.6.1.4.1.498.6 |
gdcDsx1System OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1 |
gdcDsx1Version OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.1 |
gdcDsx1SystemMIBversionIdentifies the version of the MIB. The format of the version
is x.yzT, where 'x' identifies the major revision number, 'y'
identifies the minor revision number, 'z' identifies the
typographical revision, and T identifies the test revision.
Acceptable values for the individual revision components are
as follows:
x: 1 - 9
y: 0 - 9
z: 0 - 9
T: A - Z
Upon formal release, no designation for the test revision will
be present.ro Unknown .1.3.6.1.4.1.498.6.1.1.1 |
gdcDsx1VersionTable SEQUENCE OF GdcDsx1VersionEntry .1.3.6.1.4.1.498.6.1.1.2 |
gdcDsx1VersionEntryAn entry in the GDC gdcDsx1 Version Table. GdcDsx1VersionEntry .1.3.6.1.4.1.498.6.1.1.2.1 |
gdcDsx1VersionIndexIdentifies Version parameters associated with the managed object.ro SCinstance .1.3.6.1.4.1.498.6.1.1.2.1.1 |
gdcDsx1FirmwareRevThe version number of the bootstrap firmware.
The version number of the firmware, to allow products to know which
revision is installed. The released version number is sequenced fromro DisplayString .1.3.6.1.4.1.498.6.1.1.2.1.2 |
gdcDsx1ModelNumberThis variable is used to determine the type
of card family installed ex. SC5001, SC5002.ro DisplayString .1.3.6.1.4.1.498.6.1.1.2.1.3 |
gdcDsx1ActiveFirmwareRevThe version number of the firmware currently executing.
The format is MM.NN.BB where:
MM: Major Revision (0-99)
NN: Minor Revision (0-99)
BB: Bug Fix Revision (0-99)ro DisplayString .1.3.6.1.4.1.498.6.1.1.2.1.4 |
gdcDsx1StoredFirmwareRevThe version number of the firmware stored (in a compressed format)
but not currently executing.
MM: Major Revision (0-99)
NN: Minor Revision (0-99)
BB: Bug Fix Revision (0-99)ro DisplayString .1.3.6.1.4.1.498.6.1.1.2.1.5 |
gdcDsx1BootRevThe version number of the bootstrap firmware.
The version number of the firmware, to allow products to know which
revision is installed. The released version number is sequenced fromro DisplayString .1.3.6.1.4.1.498.6.1.1.2.1.6 |
gdcDsx1StoredFirmwareStatusThis object represents the state of the Non-Active or Stored firmware:
statBlank(1) Factory Default
statDownLoading(2) In process of downloading firmware
statOK(3) Zipped version checksum succesful (OK to switch)
(can set gdcDsx1SwitchActive to switchActive(2))
statCheckSumBad(4) Failed checksum after download
statUnZipping(5) In process of uncompressing into active area
statBadUnZip(6) Failed last uncompress
The object is read only.ro Enumeration .1.3.6.1.4.1.498.6.1.1.2.1.7 |
gdcDsx1SwitchActiveFirmwareThis object is used to switch the active executing firmware from the version
in gdcDsx1ActiveRev to the version in gdcDsx1StoredRev.
When a switchActive(2) is set (write only) the element will:
1) reboot
2) uncompress stored code into active area
3) perform checksum on active area
4) Set gdcDsx1StoredStatus object to indicate results
5) If succesfull:
update gdcDsx1ActiveFirmwareRev and gdcDsx1StoredFirmwareRev
and begin executing
If failed:
replace active area with previous revision
The switchNorm(1) enumeration will always be read.
Setting switchActive(2) when the gdcDsx1StoredStatus is not statOK(3) will
result in an error.rw Enumeration .1.3.6.1.4.1.498.6.1.1.2.1.8 |
gdcDsx1DownloadingModeThis object is used to configure the download mode:
disableAll(1) Prevents any firmware downloading to gdcDsx1
enableAndWait(2) Allows downloading zipped code to be stored only!
enableAndSwitch(3) Allows downloading and then unzips and begins executing
the new coderw Enumeration .1.3.6.1.4.1.498.6.1.1.2.1.9 |
gdcDsx1Maintenance OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.2 |
gdcDsx1MaintenanceTableThe table describes the maintenance objects for
the unit and references the unit interface (cc = 00). SEQUENCE OF GdcDsx1MaintenanceEntry .1.3.6.1.4.1.498.6.1.2.1 |
gdcDsx1MaintenanceEntryAn entry in the GDC ltu Maintenance Configuration Table. GdcDsx1MaintenanceEntry .1.3.6.1.4.1.498.6.1.2.1.1 |
gdcDsx1MaintenanceLineIndexThis object identifies Maintenance parameters associated
with the managed object.ro SCinstance .1.3.6.1.4.1.498.6.1.2.1.1.1 |
gdcDsx1SoftResetSupports the action of soft resetting the unit. When this
object is set to reset(1), then the unit performs a soft
reset, whose meaning is specific to the type of unit being
managed. The value of norm(2) will be returned when
the reset is complete.
The value of norm(2) can not be set by management.rw Enumeration .1.3.6.1.4.1.498.6.1.2.1.1.2 |
gdcDsx1ConfigModeThe hardware configuration mode of the unit. A unit may
be configured through hardware switches, jumper, straps, etc.
The value software(2) indicates that the unit is software
configurable. The value of hardware(1) indicates that some
options are hard configured and that software
configuration is not permitted of these options.
The value of hardware(1) can not be set by management.ro Enumeration .1.3.6.1.4.1.498.6.1.2.1.1.4 |
gdcDsx1FrontPanelThis variable is used to indicate whether the front
panel switches are operational or not.
'inhibit' refers to when the front panel switches are
not operational.
'enable' refers to when the front panel switches are
operational.rw Enumeration .1.3.6.1.4.1.498.6.1.2.1.1.5 |
gdcDsx1SysUpTimeThis variable is used to report the elapsed system tick
time for conversion to real time at the controller and is
not related to the sysUpTime referenced in MIB-II.
Upon power-up of the unit, the elapsed time is cleared.
The elapsed time counter rolls over upon reaching the
maximum count.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.498.6.1.2.1.1.6 |
gdcDsx1DefaultInitThis is used to allow the NonVolatile Configuration to
be set to a factory default state. When this value is set to
factoryDefault(1) the unit will perform
a reset to make the default configuration take affect.
The value of normal(2) will be returned when the initialization
is complete.
The value of normal(2) can not be set by management.rw Enumeration .1.3.6.1.4.1.498.6.1.2.1.1.7 |
gdcDsx1ResetStatsSupports the action of soft resetting the dsx1ValidIntervals
object. When this object is set to reset(9), then the unit
will reset the dsx1ValidIntervals object to zero.
The value of norm(1) can not be set by management.rw Enumeration .1.3.6.1.4.1.498.6.1.2.1.1.8 |
gdcDsx1LedStatusReturns a bitwise snapshot of the front panel LED state.
Octet 1 bit 7 - not used
bit 6 - ON
bit 5 - INSV
bit 4 - RSP
bit 3 - TMG
bit 2 - EQ LAD
bit 1 - EQ 0'S
bit 0 - EQ NS
Octet 2 bit 7 - not used
bit 6 - EQ OOF
bit 5 - NTWK AIS
bit 4 - NTWK BPV
bit 3 - NTWK NS
bit 2 - NTWK OOF
bit 1 - ALM
bit 0 - TM
Octet 3 bit 7 - not used
bit 6 - ST
bit 5 - LT
bit 4 - RL
bit 3 - future use
bit 2 - future use
bit 1 - future use
bit 0 - future usero OCTET STRING .1.3.6.1.4.1.498.6.1.2.1.1.9 |
gdcDsx1SetTransmitClkSrc'txClkSrc' indicates the unit is using the optioned
clock source as indicated by the dsx1TransmitClockSource
variable in the RFC1406 mib or the gdcDsx1TransmitClockSource
variable in the gdcdsx1 mib.
'fallBackClkSrc' indicates the unit is using the optioned
clock source as indicated by the gdcDsx1FallbackClockSource
variable in the gdcdsx1 mib.rw Enumeration .1.3.6.1.4.1.498.6.1.2.1.1.10 |
gdcDsx1CsuMode'csuMode' indicates the unit is operating as a T1 channel
service unit with the payload from the network interface
connected to the payload of the cascade interface.
'concentratorMode' indicates the unit is operating as a T1
channel service unit with the T1 payloads groomed to
cross connect within the shelf and the network and cascade
interfaces.rw Enumeration .1.3.6.1.4.1.498.6.1.2.1.1.11 |
gdcDsx1CircuitIdentifier1Private data storage area of sixteen bytes.rw DisplayString .1.3.6.1.4.1.498.6.1.2.1.1.12 |
gdcDsx1CircuitIdentifier2Private data storage area of sixteen bytes.rw DisplayString .1.3.6.1.4.1.498.6.1.2.1.1.13 |
gdcDsx1Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.3 |
gdcDsx1ConfigTableThe GDC DS1 Configuration table. Information in the entries
of this table augment the entries in the DS1 Configuration
table of the DS1 MIB defined in RFC 1406. SEQUENCE OF GdcDsx1ConfigEntry .1.3.6.1.4.1.498.6.1.3.1 |
gdcDsx1ConfigEntryThe GDC DS1 Configuration table entry. The information in
this entry augments the information for the corresponding
entry in the dsx1ConfigEntry of the DS1 MIB defined in RFC
1406. GdcDsx1ConfigEntry .1.3.6.1.4.1.498.6.1.3.1.1 |
gdcDsx1ConfigIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier.ro SCinstance .1.3.6.1.4.1.498.6.1.3.1.1.1 |
gdcDsx1LineTypeThis variable indicates the variety of DS-X Line implementing
this circuit. The type of circuit affects the number of bits per
second that the circuit can reasonably carry, as well as the
interpretation of the usage and error statistics.
The values, in sequence, describe:
'auto' indicates the unit is still determining
framing when gdcDsx1LineType is set for auto (1)
dsx1LineType reads other(1).
'manEsf' indicates manual selection of extended
superframe format
'manD4'indicates manual selection of D4 framing
format
'unframed' indicates manual selection of unframed
format
Reference rfc1406
dsx1LineType gdcDsx1LineType
dsx1ESF (2) ============> manESF (2)
dsx1D4 (3) ============> manD4 (3)
All other values in dsx1LineType are not supported
at this time.
Default value: manESF (2)rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.2 |
gdcDsx1InterfaceTypeThe operating mode of the interface. Setting the value of
this object to ds1(2) configures the interface as
standard DS1. Setting the value of this object to
dsx1(3) configures the interface to operate as a standard
cross-connect DSX-1.
The value other(1) identifies another interface mode defined
elsewhere. This value can never be set by management operation.
This object interoperates with the gdcDsx1Preequalization
object. When this object is set to ds1(2), then the value of
gdcDsx1Preequalization does not apply.
This object interoperates with the gdcDsx1AdminLineBuildout object.
When this object is set to dsx1(3), then the value of
gdcDsx1LineBuildout does not apply.
This object interoperates with the gdcDsx1AdminLineBuildout
object. When this object is set to dsx1(3), then the value of
gdcDsx1AutoLineBuildout does not apply.
This object interoperates with the gdcDsx1AdminReceiveRange object.
When this object is set to dsx1(3), then the value of
gdcDsx1ReceiveRange does not apply.
This object interoperates with the gdcDsx1AdminReceiveRange
object. When this object is set to dsx1(3), then the value of
gdcDsx1AutoReceiveRange is set to disabled(2).rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.3 |
gdcDsx1PreequalizationIs the preequalization of the transmitter of the interface.
The value other(1) identifies an other preequalization value
which is defined elsewhere. This value can never be set by
management operation.
This object interoperates with the object
gdcDsx1InterfaceType. When the value of gdcDsx1InterfaceType
is ds1(2) then this value is not applicable.rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.4 |
gdcDsx1AdminLineBuildoutThis variable is used to set the Transmit Ntwk
Build-Out value on the network side and is only
valid if the gdcDsx1InterfaceType is set for ds1(1).
The values, in sequence, describe:
'auto' indicates auto detection of receive level to
determine the appropriate Ntwk build out without
controller intervention
'man00dB' indicates manual selection of 0.0 dB
transmit Ntwk build out
'man75dB' indicates manual selection of -7.5 dB
transmit Ntwk build out
'man150dB' indicates manual selection of -15.0 dB
transmit Ntwk build out
Set/get of auto requires a reading of gdcDsx1OperLineBuildOut
to determine the selection of
the Ntwk buildout. Caution must be used when setting
auto since only one unit on a link can be in auto at
a given time.
Default value: man00dB (2)rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.5 |
gdcDsx1OperLineBuildoutThis variable is used to report the current Ntwk
build-out setting if the gdcDsx1InterfaceType is set for ds1(1).
'inProcess' indicates the unit is still determining the
Ntwk build out required when the gdcDsx1AdminLineBuildout is
set for auto (1)
'tx00dB' indicates the unit is set for 0.0 dB of attenuation
when the gdcDsx1AdminLineBuildout is set for auto (1) or
man00dB (2)
'tx75dB' indicates the unit is set for -7.5 dB of attenuation
when the gdcDsx1AdminLineBuildout is set for auto (1) or
man75dB (3)
'tx150dB' indicates the unit is set for -15.0 dB of attenuation
when the gdcDsx1AdminLineBuildout is set for auto (1) or
man150dB (4)ro Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.6 |
gdcDsx1AdminRcvRangeThis variable is used to set the receiver
circuitry for signal recovery ranges when gdcDsx1InterfaceType
is set for ds1 (1). This function is not supported for
gdcDsx1InterfaceType set for dsx1 (2). Normal
range is considered 0 to -28 dB and extended
range is from -20 to -40 dB relative to a DS-1
launch pulse. The values,in sequence, describe:
'auto' indicates auto selection of receiver range
'manNorm' indicates manual selection of normal range
'manExt' indicates manual selection of extended range
Set/get of auto requires a reading of
gdcDsx1OperRcvRange to determine the selection of
the receiver range. Caution must be used when setting
auto since only one unit on a link can be in auto at
a given time.
Default value: auto(1)rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.7 |
gdcDsx1OperRcvRangeThis variable is used to report the current receiver
range setting when gdcDsx1InterfaceType is set for ds1 (1).
'inProcess' indicates the unit is still determining
the required receiver range when the gdcDsx1AdminRcvRange is
set for auto (1)
'norm' indicates the receiver is set for normal range
when the gdcDsx1AdminRcvRange is set for auto (1) or manNorm (2)
'ext' indicates the receiver is set for extended range
when the gdcDsx1AdminRcvRange is set for auto (1) or manExt (3)ro Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.8 |
gdcDsx1OnesDensityThe ones density restriction for the interface. The values
of this object define the ones density restriction that is
enforced on the interface.
The value inhibit(1) indicates that no ones density restriction
is enforced.
The value max15zeros(2) indicates that a maximum of 15 zeros
are transmitted to the network before a one is inserted.
The value max39zeros(3) indicates that a maximum of 39 zeros
are transmitted to the network before a one is inserted.
The value restrict8nX1(4) indicates a minimum of N ones per
8(N+1) bits, where N is in the range 1 to 24.
The value min1in8(5) indicates a minimum of 1 one per 8 bits.
With this value, pulse density violations are enforced but not
recorded.rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.9 |
gdcDsx1TransmitClockSourceAugments the dsx1TransmitClockSource of the DS1 MIB of RFC
1406. This object defines transmit clock sources that are not
defined by RFC 1406, but are supported by GDC DS1
interfaces.
The value other(1) indicates that the DS1 transmit clock
source is defined elsewhere. The other values identify other
timing sources as indicated.
The value other(1) can never be set by management operation.
This object interoperates with the dsx1TransmitClockSource
object. When the dsx1TransmitClockSource is set to
loopTiming(1) or localTiming(2), the value of this object
reflects other(1). When the value of this object has a value
other than other(1), then the value of the
dsx1TransmitClockSource object reflects throughTiming(3).
The value channel(4) interoperates with the
gdcDsuChannelTransmitClockSource object. When this value is
selected, gdcDsuChannelTransmitClockSource is set to the
appropriate channel of the clock source for multi-channel
products.rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.10 |
gdcDsx1FallbackClockSourceIdentifies the fallback transmit clock source. The value of
other(1) identifies another fallback transmit clock source
that is defined elsewhere. The value of none(2) indicates no
fallback transmit clock source.
The value other(1) can never be set by management operation.
The value channel(4) interoperates with the
gdcDsuChannelTransmitClockSource object. When this value is
selected, gdcDsuChannelTransmitClockSource is set to the
appropriate channel of the clock source for multi-channel
products.rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.11 |
gdcDsx1AISLoopdownThe time in seconds when receiving a continuous AIS signal
before a remotely initiated loopback is terminated. When this
object has the value 4, then there is no time limit and the
loop must be terminated by remotely issued in-band loopdown
codes. When the object has a value between 5 and 60, then
this is time in seconds of continuous AIS signal before
the loopback is terminated.rw INTEGER .1.3.6.1.4.1.498.6.1.3.1.1.14 |
gdcDsx1InbandLoopCfgThis variable is used to set the
In-Band DS1 Loopback Code Detection.
'inhibit' refers to when the in-band
loopback codes are ignored.
'payload' designates a payload loopback
is done upon recognition of the inband loopback
code.
'lineloop' designates a line loopback is done
upon recognition of the inband loopback code.rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.15 |
gdcDsx1RedundancyThis variable identifies which unit is the Primary
unit and which unit is the Secondary unit. When
the value is onLine(1), then the unit is identified
as the Primary unit. When the value is backUp(2),
then the unit is identified as the Secondary unit.
The value keepAlive(3) indicates that a physical strap
is enabled on the unit and that the values of onLine(1)
and backUp(2) are ignored.
The value keepAlive(3) can never be set by network
management.rw Enumeration .1.3.6.1.4.1.498.6.1.3.1.1.16 |
gdcDsx1Diagnostics OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.4 |
gdcDsx1DiagTableThe GDC DS1 Diagnostics table. Information in the entries of
this table support diagnostics testing, both active testing
via patterns, and passive testing via loopbacks. The
information of this table augments the entries in the DS1
Configuration table of the DS1 MIB defined in RFC 1406. SEQUENCE OF GdcDsx1DiagEntry .1.3.6.1.4.1.498.6.1.4.1 |
gdcDsx1DiagEntryThe GDC DS1 Diagnostics table entry. The information in this
entry augments the information for the corresponding entry in
the DS1 Configuration table of the DS1 MIB defined in RFC 1406. GdcDsx1DiagEntry .1.3.6.1.4.1.498.6.1.4.1.1 |
gdcDsx1DiagIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier,
which in this case is a network interface.ro SCinstance .1.3.6.1.4.1.498.6.1.4.1.1.1 |
gdcDsx1SendCodeAugments the dsx1SendCode object from the DS1 MIB of RFC
1406. This object defines other codes that are not defined by
dsx1SendCode.
The value of other(1) can never be set by management
operation.
This object and the dsx1SendCode object interoperate. When
the value of dsx1SendCode is set to something other than
dsx1SendOtherTestPattern(8), then the value of this object is
set to other(1). When the value of this object is set to
something other than other(1), the the value of dsx1SendCode
is set to dsx1SendOtherTestPattern(8).
This object and the gdcDsx1ProgPattern object interrelate.
When this object is set to the value sendProgPattern(4), the
value of the gdcDsx1ProgPattern object is used as the 16
bit user programmable pattern.
The values send511PatternWithLT(11), send511PatternWithRT(12),
send2047PatternWithLT(13), send2047PatternWithRT(14), sendQRSPatternWithLT(15),
sendQRSPatternWithRT(16), sendProgPatternWithLT(17), sendProgPatternWithRT(18),
send3in24PatternWithRT(19) indicate that the given pattern test is running in
conjunction with a local test (LT) or remote test (RT). gdcDsx1LoopbackConfig
is updated to indicate this as well. When one of these tests are running, and
dsx1SendCode is set to dsx1SendNoCode(1), both the pattern and the loopback
are terminated. However, if dsx1LoopbackConfig is set to dsx1NoLoop(1),
and a pattern with LT is in progres, only the loopback portion is terminated.rw Enumeration .1.3.6.1.4.1.498.6.1.4.1.1.2 |
gdcDsx1LoopbackConfigAugments the dsx1LoopbackConfig object from the DS1 MIB of RFC
1406. This object defines other loopback configurations that
are not defined by dsx1LoopbackConfig.
The value of other(1) can never be set by management
operation.rw Enumeration .1.3.6.1.4.1.498.6.1.4.1.1.4 |
gdcDsx1DS0DiagDefines a DS0 level diagnostic. Setting this object value to 0
disables a DS0 level diagnostic. Setting this object to a value
from 1 to 32 enables a DS0 level diagnostic on the DS0 indicated.
Enabling a DS0 level diagnostic bysetting this object to a value
from 1 to 32 alters the meaning of the diagnostic test to be
specific to the DS0 specified instead of the whole DS1.
Note that a DS0 level diagnostic and a DS1 level diagnostic
cannot be performed simultaneously.rw INTEGER .1.3.6.1.4.1.498.6.1.4.1.1.5 |
gdcDsx1TestDurationSelects the duration to run a diagnostic test. The value(1)
noLimit signifies that the test should run indefinitely until
explicitly terminated.
Default value: noLimit (1)rw Enumeration .1.3.6.1.4.1.498.6.1.4.1.1.6 |
gdcDsx1TestExecutionStatusThis variable reports the status of a test. notInTest(1) indicates
a test is not running. testInProgress(2) indicates that a test is
currently running. testCompleted(4) indicates that a test has run
and is completed. testCompletedNotInTest(5) indicates that a test has
completed and it is no longer in test.ro Enumeration .1.3.6.1.4.1.498.6.1.4.1.1.8 |
gdcDsx1TestExceptionsIndicates exceptions that have occurred that may affect
interpretation of the test results.
The value of this object is a sum. This sum initially take
the value zero. Then, for each exception, the value
associated with the exception is added to the sum.
The exception values are:
value exception
1 a timed test was preempted so the result
cannot be viewed in relation to the test
duration
2 the results overflowed so the result cannot be
viewed as an absolute value
4 the test was performed while synchronization
could not be performed so the result may not
be accurate.ro INTEGER .1.3.6.1.4.1.498.6.1.4.1.1.9 |
gdcDsx1TestResultsThe results of the last diagnostic test. This can be the
current test running or the last completed test.
Note that the interpretation of these results may be affected
by the value of the gdcDsx1TestExceptions object.
The units of the value of this object depend on the type of
diagnostic test run. For all cases except a DS0 delay
measurement, the units of the value of this object is the
number of errors that occurred. For a DS0 delay measurement,
the units of the value of this test are milliseconds.ro INTEGER .1.3.6.1.4.1.498.6.1.4.1.1.10 |
gdcDsx1Performance OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.5 |
gdcDsx1ANSIperfTableThe GDC ANSI Performance table. Information in the entries
of this table support the ANSI Scheduled Performance Reports.
Entries supply information for both inbound and outbound
reports for the last 4 seconds. SEQUENCE OF GdcDsx1ANSIperfEntry .1.3.6.1.4.1.498.6.1.5.1 |
gdcDsx1ANSIperfEntryThe GDC ANSI Performance table entry. The information in
this entry presents one of the 4 second periods performance
data in either the inbound or outbound direction. GdcDsx1ANSIperfEntry .1.3.6.1.4.1.498.6.1.5.1.1 |
gdcDsx1ANSIperfIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is a network interface.ro SCinstance .1.3.6.1.4.1.498.6.1.5.1.1.1 |
gdcDsx1ANSIdirectionIdentifies the direction of the report entry. This is either
an outbound(1) report or an inbound(2) report.ro Enumeration .1.3.6.1.4.1.498.6.1.5.1.1.2 |
gdcDsx1ANSIsecondsIdentifies the reporting interval. This has the value 1 to 4
supporting up to the last 4 seconds of performance data.ro INTEGER .1.3.6.1.4.1.498.6.1.5.1.1.3 |
gdcDsx1ANSICRCerrorEventsIdentifies the magnitude of the error events in the interval
which this entry represents.ro Enumeration .1.3.6.1.4.1.498.6.1.5.1.1.4 |
gdcDsx1ANSIsevereErrorsIdentifies whether or not any severe errors were detected in
the interval which this entry represents.ro Enumeration .1.3.6.1.4.1.498.6.1.5.1.1.5 |
gdcDsx1ANSIframeErrorsIdentifies whether or not any framing errors were detected in
the interval which this entry represents.ro Enumeration .1.3.6.1.4.1.498.6.1.5.1.1.6 |
gdcDsx1ANSIcodeViolationsIdentifies whether or not any code violations were detected in
the interval which this entry represents.ro Enumeration .1.3.6.1.4.1.498.6.1.5.1.1.7 |
gdcDsx1ANSIcontrolledSlipsIdentifies whether or not any controlled slips were detected in
the interval which this entry represents.ro Enumeration .1.3.6.1.4.1.498.6.1.5.1.1.8 |
gdcDsx1ANSIactivePayloadLoopsIdentifies whether or not any active payload loops were detected in
the interval which this entry represents.ro Enumeration .1.3.6.1.4.1.498.6.1.5.1.1.9 |
gdcDsx1CurrentTableThe gdcDsx1 Current table. This table supplements the
entries in the DS1 AT&T performance table of the DS1
MIB defined in RFC1406. SEQUENCE OF GdcDsx1CurrentEntry .1.3.6.1.4.1.498.6.1.5.2 |
gdcDsx1CurrentEntryAn entry in the gdcDsx1 Current table. GdcDsx1CurrentEntry .1.3.6.1.4.1.498.6.1.5.2.1 |
gdcDsx1CurrentIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is a network interface.ro SCinstance .1.3.6.1.4.1.498.6.1.5.2.1.1 |
gdcDsx1CurrentLOFCsThe number of Loss of Frame Counts (LOFCs) encountered by a DS1
interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.498.6.1.5.2.1.2 |
gdcDsx1CurrenUserStatReturns a bitwise snapshot of the statistics.
Octet 1 bit 7 - parity
bit 6 - 2^15 Errored Seconds
bit 5 - 2^14
bit 4 - 2^15 Severely Errored Seconds
bit 3 - 2^14
bit 2 - 2^15 Bursty Errored Seconds
bit 1 - 2^14
bit 0 - 1: New Interval
Octet 2 bit 7 - parity
bit 6 - 2^13 Errored Seconds
bit 5 - 2^12
bit 4 - 2^11
bit 3 - 2^10
bit 2 - 2^9
bit 1 - 2^8
bit 0 - 2^7
Octet 3 bit 7 - parity
bit 6 - 2^6 Errored Seconds
bit 5 - 2^5
bit 4 - 2^4
bit 3 - 2^3
bit 2 - 2^2
bit 1 - 2^1
bit 0 - 2^0
Octet 4 bit 7 - parity
bit 6 - 2^13 Severely Errored Seconds
bit 5 - 2^12
bit 4 - 2^11
bit 3 - 2^10
bit 2 - 2^9
bit 1 - 2^8
bit 0 - 2^7
Octet 5 bit 7 - parity
bit 6 - 2^6 Severely Errored Seconds
bit 5 - 2^5
bit 4 - 2^4
bit 3 - 2^3
bit 2 - 2^2
bit 1 - 2^1
bit 0 - 2^0
Octet 6 bit 7 - parity
bit 6 - 2^13 Bursty Errored Seconds
bit 5 - 2^12
bit 4 - 2^11
bit 3 - 2^10
bit 2 - 2^9
bit 1 - 2^8
bit 0 - 2^7
Octet 7 bit 7 - parity
bit 6 - 2^6 Bursty Errored Seconds
bit 5 - 2^5
bit 4 - 2^4
bit 3 - 2^3
bit 2 - 2^2
bit 1 - 2^1
bit 0 - 2^0
Octet 8 bit 7 - parity
bit 6 - f/u
bit 5 - f/u
bit 4 - 2^15 Unavailable Seconds
bit 3 - 2^14
bit 2 - f/u
bit 1 - 2^7 Loss of Frame Count
bit 0 - 2^7 Controlled Slip Seconds
Octet 9 bit 7 - parity
bit 6 - 2^13 Unavailable Seconds
bit 5 - 2^12
bit 4 - 2^11
bit 3 - 2^10
bit 2 - 2^9
bit 1 - 2^8
bit 0 - 2^7
Octet 10 bit 7 - parity
bit 6 - 2^6 Unavailable Seconds
bit 5 - 2^5
bit 4 - 2^4
bit 3 - 2^3
bit 2 - 2^2
bit 1 - 2^1
bit 0 - 2^0
Octet 11 bit 7 - parity
bit 6 - 2^6 Controlled Slip Second
bit 5 - 2^5
bit 4 - 2^4
bit 3 - 2^3
bit 2 - 2^2
bit 1 - 2^1
bit 0 - 2^0
Octet 12 bit 7 - parity
bit 6 - 2^6 Loss of Frame Count
bit 5 - 2^5
bit 4 - 2^4
bit 3 - 2^3
bit 2 - 2^2
bit 1 - 2^1
bit 0 - 2^0
Octet 13 bit 7 - parity
bit 6 - 2^6 Percent Complete
bit 5 - 2^5
bit 4 - 2^4
bit 3 - 2^3
bit 2 - 2^2
bit 1 - 2^1
bit 0 - 2^0ro OCTET STRING .1.3.6.1.4.1.498.6.1.5.2.1.3 |
gdcDsx1IntervalTableThe gdcDsx1 Interval table. This table supplements the
entries in the DS1 AT&T performance table of the DS1
MIB defined in RFC1406. SEQUENCE OF GdcDsx1IntervalEntry .1.3.6.1.4.1.498.6.1.5.3 |
gdcDsx1IntervalEntryAn entry in the DS1 Interval table. GdcDsx1IntervalEntry .1.3.6.1.4.1.498.6.1.5.3.1 |
gdcDsx1IntervalIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is a network interface.ro SCinstance .1.3.6.1.4.1.498.6.1.5.3.1.1 |
gdcDsx1IntervalNumberA number between 1 and 96, where 1 is the most recently completed
15 minute interval and 96 is the least recently completed 15 minutes
interval (assuming that all 96 intervals are valid).ro INTEGER .1.3.6.1.4.1.498.6.1.5.3.1.2 |
gdcDsx1IntervalLOFCsThe number of Loss of Frame Counts (LOFCs) encountered by a DS1
interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.498.6.1.5.3.1.3 |
gdcDsx1TotalTableThe DS1 Total table. 24 hour interval.
This table supplements the entries in the DS1
AT&T performance table of the DS1
MIB defined in RFC1406. SEQUENCE OF GdcDsx1TotalEntry .1.3.6.1.4.1.498.6.1.5.4 |
gdcDsx1TotalEntryAn entry in the DS1 Total table. GdcDsx1TotalEntry .1.3.6.1.4.1.498.6.1.5.4.1 |
gdcDsx1TotalIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is a network interface.ro SCinstance .1.3.6.1.4.1.498.6.1.5.4.1.1 |
gdcDsx1TotalLOFCsThe number of Loss of Frame Counts (LOFCs) encountered by a
DS1interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.498.6.1.5.4.1.2 |
gdcDsx1Alarms OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.6 |
gdcDsx1AlarmConfigTableThe gdcAlarmConfigTable contains entries that configure alarm
reporting. The structure of the table is such that alarm
configuration is supported on a unit and interface basis, and
then on an alarm type basis within the interface. For
simplicity sake alarms, be they unit or interface
related, are represented in one table. SEQUENCE OF GdcDsx1AlarmConfigEntry .1.3.6.1.4.1.498.6.1.6.1 |
gdcDsx1AlarmConfigEntryAn entry in the GDC Alarm Configuration table. GdcDsx1AlarmConfigEntry .1.3.6.1.4.1.498.6.1.6.1.1 |
gdcDsx1AlarmConfigIndexThe index value which uniquely identifies the interface to
which this entry is applicable.ro SCinstance .1.3.6.1.4.1.498.6.1.6.1.1.1 |
gdcDsx1AlarmConfigIdentifierThe unique alarm identifier assigned to this alarm type.
The format of this identifier is an OBJECT IDENTIFIER that has
the following format: {iso(1) org(3) dod(6) internet(1)
private(4) enterprises(1) gdc(498) xxx(x) alarm(z) yyy(y)
where xxx(x) is the administratively assigned family object
identifier (z) is the object identifier for alarms in the family
defined MIB and yyy(y) is the administratively assigned alarm
type identifier for this alarm.ro OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.6.1.1.2 |
gdcDsx1AlarmCountWindowThis variable sets/reads the BPV alarm window.
This window is used with the alarm threshold to determine
how long the alarm should be active before reporting.
Default: disabled(1)rw Enumeration .1.3.6.1.4.1.498.6.1.6.1.1.3 |
gdcDsx1AlarmCountThresholdThis function sets/reads the BPV alarm threshold criteria.
This threshold is used along with the the alarm window to
determine the number of instances in a given time frame for
an alarm to occur before the alarm is considered active.
Default: thresGT10(1)rw Enumeration .1.3.6.1.4.1.498.6.1.6.1.1.4 |
gdcDsx1AlarmStatusTableThe gdcDsx1AlarmStatusTable contains entries that report the
status of alarms. The status of an alarm consists of the
current alarm status, indicating whether or not the alarm
condition is in effect, the number of times the alarm has
occurred, the time of the first alarm occurrence, and the time
of the last alarm occurrence.
The structure of the table is such that alarm status is
supported on a unit or interface basis, and then on an alarm
type basis within the interface. For simplicity sake and to
support the reporting of status of all alarms, a unit is
treated as an interface in this table. SEQUENCE OF GdcDsx1AlarmStatusEntry .1.3.6.1.4.1.498.6.1.6.2 |
gdcDsx1AlarmStatusEntryAn entry in the GDC Alarm Status table. GdcDsx1AlarmStatusEntry .1.3.6.1.4.1.498.6.1.6.2.1 |
gdcDsx1AlarmStatusIndexThe index value which uniquely identifies the interface to
which this entry is applicable.ro SCinstance .1.3.6.1.4.1.498.6.1.6.2.1.1 |
gdcDsx1AlarmStatusIdentifierThe unique alarm identifier assigned to this alarm type.
The format of this identifier is an OBJECT IDENTIFIER that has
the following format: {iso(1) org(3) dod(6) internet(1)
private(4) enterprises(1) gdc(498) xxx(x) alarm(z) yyy(y)
where xxx(x) is the administratively assigned family object
identifier (z) is the object identifier for alarms in the family
defined MIB and yyy(y) is the administratively assigned alarm
type identifier for this alarm.ro OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.6.2.1.2 |
gdcDsx1AlarmCountThe number of occurrences of this alarm. This objects value
is incremented once for each time that the alarm occurs. This
count is incremented regardless of whether or not the alarm
is masked or is not reporteded because of the threshold
configuration.
If the network element type does not support this variable, a
noSuch will be returned.ro Gauge .1.3.6.1.4.1.498.6.1.6.2.1.3 |
gdcDsx1AlarmFirstOccurrenceThe time at which the alarm first occurred. This is reported
as the number of TimeTicks after the interface was
initialized. This object along with its companion object,
gdcDsx1AlarmLastOccurrence, can be used to provide greater meaning
to the value of gdcDsx1AlarmOccurrenceCount by weighing the count
over the period of time.
If the network element type does not support this variable, a
noSuch will be returned.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.498.6.1.6.2.1.4 |
gdcDsx1AlarmLastOccurrenceThe time at which the alarm last occurred. This is reported
as the number of TimeTicks after the interface was
initialized. This object along with its companion object,
gdcDsx1AlarmFirstOccurrence, can be used to provide greater meaning
to the value of gdcDsx1AlarmOccurrenceCount by weighing the count
over the period of time.
If the network element type does not support this variable, a
noSuch will be returned.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.498.6.1.6.2.1.5 |
gdcDsx1NetMaintenance OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.1.7 |
gdcDsx1NetMaintTableThe table describes the maintenance objects for
the network and references the network interface (cc = 01). SEQUENCE OF GdcDsx1NetMaintEntry .1.3.6.1.4.1.498.6.1.7.1 |
gdcDsx1NetMaintEntryAn entry in the GDC ltu Network Maintenance Configuration
Table. GdcDsx1NetMaintEntry .1.3.6.1.4.1.498.6.1.7.1.1 |
gdcDsx1NetMaintLineIndexThis object identifies Maintenance parameters associated
with the managed object.ro SCinstance .1.3.6.1.4.1.498.6.1.7.1.1.1 |
gdcDsx1NetMaintReceiveLevelThis variable reports the absolute value of the network relative
receive level of -40dB to +3dB when the gdcDsx1InterfaceType is set
for ds1(1). This object interacts with the gdcDsx1NetMaintAttenSense
object in determining the unit's actual Receive Level.ro INTEGER .1.3.6.1.4.1.498.6.1.7.1.1.2 |
gdcDsx1NetMaintAttenSenseThis variable identifies ths sense of the
gdcdsx1NetReceiveLevel variable.ro Enumeration .1.3.6.1.4.1.498.6.1.7.1.1.3 |
sc5001 OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2 |
dsx1AlarmData OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1 |
dsx1NoResponseAlm OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.1 |
dsx1DiagRxErrAlm OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.2 |
dsx1PowerUpAlm OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.3 |
dsx1NvRamCorrupt OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.4 |
dsx1UnitFailure OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.5 |
dsx1MbiLock OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.6 |
dsx1LocalPwrFail OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.7 |
dsx1TimingLoss OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.8 |
dsx1StatusChange OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.9 |
dsx1UnsoTest OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.10 |
dsx1LossOfSignal OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.11 |
dsx1LossOfFrame OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.12 |
dsx1Ais OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.13 |
dsx1ReceivedYellow OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.14 |
dsx1UnavailSignalState OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.15 |
dsx1ExcessiveZeros OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.16 |
dsx1LowAverageDensity OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.17 |
dsx1ControlledSlips OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.18 |
dsx1BipolarViolations OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.19 |
dsx1CrcErrors OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.20 |
dsx1FallbackTimingActive OBJECT IDENTIFIER .1.3.6.1.4.1.498.6.2.1.21 |