Fore-J2-MIB
write something interesting here
Main OID:
foreJ2.1.3.6.1.4.1.326.2.2.1.1.6
36
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
36 total| Object Name |
|---|
foreJ2write something interesting here MODULE-IDENTITY .1.3.6.1.4.1.326.2.2.1.1.6 |
j2ConfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.6.1 |
j2ConfTableA table of J2 switch port configuration information. SEQUENCE OF J2ConfEntry .1.3.6.1.4.1.326.2.2.1.1.6.1.1 |
j2ConfEntryA table entry containing J2 configuration information for each port. J2ConfEntry .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1 |
j2ConfBoardThe index of this port's switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.1 |
j2ConfModuleThe network module of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.2 |
j2ConfPortThe number of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.3 |
j2LineLengthThis variable represents the length of the physical medium connected to the J2 interface: j2ShortLine (1) means the line is a short line with less than 4db of attenuation from the transmitting source. j2LongLine (2) means the line is a long line, with greater than 4db of attenuation from the transmitting source.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.4 |
j2LoopbackConfigThis variable represents the loopback configuration of the J2 interface. j2NoLoop (1) means that the interface is not in a loopback state. j2LineLoop (2) means that receive signal is looped back for retransmission without passing through the port's reframing function. j2DiagLoop (3) means that the transmit data stream is looped back to the receiver. j2OtherLoop (4) means that the interface is in a loopback that is not defined here.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.5 |
j2TxClockSourceThe source of the transmit clock.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.6 |
j2LineStatusThis variable indicates the Line Status of the interface. The variable contains loopback state information and failure state information. It is a bit map represented as a sum. The j2NoAlarm should be set if and only if no other flag is set. The various bit positions are: 1 j2NoAlarm 2 j2RxLOF Receive Loss of Frame 4 j2RxLOC Receive Loss of Clock (Not used anymore) 8 j2RxAIS Receive Alarm Indication Signal 16 j2TxLOC Transmit Loss of Clock (Not used anymore) 32 j2RxRAIS Receive Remote Alarm Indication Signal 64 j2RxLOS Receive Loss of Signal 128 j2TxRAIS Transmit Yellow ( Remote Alarm Indication Signal) 256 j2Other any line status not defined here 32768 j2RxLCD Receiving LCD failure indication.ro INTEGER .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.7 |
j2IdleUnassignedCellsThis variable indicates the types of cells that should be sent in case there is no real data to send. According to the ATM Forum, Unassigned cells should be sent (octet 1-3 are 0's, octet 4 is 0000xxx0, where x is 'don't care'). According to the CCITT specifications, Idle cells should be sent (everything is '0' except for the CLP bit which is '1'). By default, unassigned cells are transmitted in case there is no data to send.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.6.1.1.1.8 |
j2StatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.6.2 |
j2ErrorTableA table of J2 error counters. SEQUENCE OF J2ErrorEntry .1.3.6.1.4.1.326.2.2.1.1.6.2.1 |
j2ErrorEntryA table entry containing J2 error counters. J2ErrorEntry .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1 |
j2ErrorBoardThe index of this port's switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.1 |
j2ErrorModuleThe network module of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.2 |
j2ErrorPortThe number of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.3 |
j2B8ZSCodingErrorsThe number of B8ZS coding violation errors.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.4 |
j2CRC5ErrorsThe number of CRC-5 received errors.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.5 |
j2FramingErrorsThe number of framing patterns received in error.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.6 |
j2RxLossOfFrameThe number of seconds during which the receiver was experiencing Loss Of Frame.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.7 |
j2RxLossOfClockThe number of seconds during which the receiver was not observing transitions on the received clock signal.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.8 |
j2RxAISThe number of seconds during which the receiver detected an Alarm Indication Signal.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.9 |
j2TxLossOfClockThe number of seconds during which the transmitter was experiencing Loss Of Clock.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.10 |
j2RxRemoteAISThe number of seconds during which the receiver observed the Alarm Indication Signal in the m-bits channel.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.11 |
j2RxLossOfSignalThe number of seconds during which the transmitter was experien cing Loss Of Signal.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.1.1.12 |
j2AtmTableA table of J2 ATM statistics information. SEQUENCE OF J2AtmEntry .1.3.6.1.4.1.326.2.2.1.1.6.2.2 |
j2AtmEntryA table entry containing J2 ATM statistics information. J2AtmEntry .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1 |
j2AtmBoardThe index of this port's switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1.1 |
j2AtmModuleThe network module of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1.2 |
j2AtmPortThe number of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1.3 |
j2AtmHCSsNumber of header check sequence (HCS) error events. The HCS is a CRC-8 calculation over the first 4 octets of the ATM cell header.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1.4 |
j2AtmRxCellsNumber of ATM cells that were received.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1.5 |
j2AtmTxCellsNumber of non-null ATM cells that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1.6 |
j2AtmLCDsThe number of seconds in which Loss of Cell Delineation (LCD) has occurred. An LCD defect is detected when an out of cell delination state has persisted for 4ms. An LCD defect is cleared when the sync state has been maintained for 4ms.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.6.2.2.1.7 |