F3-PWE3-MIB
AI MIB Summary
The F3-PWE3-MIB module enables monitoring and management of F3 Pseudo-Wire (PWE3) session states and performance metrics on ADVA Optical Networking FSP150CM/CC product lines. It provides specific counters and status indicators for the establishment, maintenance, and fault detection of pseudowire services within the F3 transport architecture.
This module provides the F3 Pseudo Wire definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
Main OID:
f3Pwe3MIB.1.3.6.1.4.1.2544.1.12.19
119
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
119 total| Object Name |
|---|
f3Pwe3MIBThis module provides the F3 Pseudo Wire definitions used by
the F3 (FSP150CM/CC) product lines.
Copyright (C) ADVA Optical Networking. MODULE-IDENTITY .1.3.6.1.4.1.2544.1.12.19 |
f3Pwe3ConfigObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.19.1 |
f3Pwe3IdlePatternProfileTableA list of entries corresponding to the PWE3 Idle Pattern
Profile entities. SEQUENCE OF F3Pwe3IdlePatternProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.1 |
f3Pwe3IdlePatternProfileEntryAn entry containing information applicable to a particular
PWE3 Idle Pattern Profile Entity. These profiles are used
by PWE3 SAToP entities. F3Pwe3IdlePatternProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.1.1 |
f3Pwe3IdlePatternProfileIndexUnique index value associated with the PWE3 Idle Pattern Profile. Integer32 .1.3.6.1.4.1.2544.1.12.19.1.1.1.1 |
f3Pwe3IdlePatternProfileByteThis object allows SNMP management entities to specify the
Idle Pattern Profile information.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.1.1.2 |
f3Pwe3ResyncProfileTableA list of entries corresponding to the PWE3 Resync Profile entities. SEQUENCE OF F3Pwe3ResyncProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.2 |
f3Pwe3ResyncProfileEntryAn entry containing information applicable to a particular
PWE3 Resync Profile Entity. These profiles are used
by PWE3 SAToP entities. F3Pwe3ResyncProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.2.1 |
f3Pwe3ResyncProfileIndexUnique index value associated with the PWE3 Resync Profile. Integer32 .1.3.6.1.4.1.2544.1.12.19.1.2.1.1 |
f3Pwe3ResyncProfileIncreaseFactorThis object allows SNMP management entities to specify the
PWE3 Resync Profile Increase Factor. This is used to define
the fill rate of the leaky bucket algorithm associated with the
Resync mechanism.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.2.1.2 |
f3Pwe3ResyncProfileDecreaseFactorThis object allows SNMP management entities to specify the
PWE3 Resync Profile Decrease Factor. This is used to define
the leak rate for the leaky bucket algorithm associated with
the Resync mechanism.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.2.1.3 |
f3Pwe3ResyncProfileResyncThresholdThis object allows SNMP management entities to specify the
PWE3 Resync Profile Resync Threshold. This is the threshold value
at which point the pseudo-wire connection is deemed out of
synchronization state.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.2.1.4 |
f3Pwe3LoopbackProfileTableA list of entries corresponding to the PWE3 Loopback Profile entities. SEQUENCE OF F3Pwe3LoopbackProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.3 |
f3Pwe3LoopbackProfileEntryAn entry containing information applicable to a particular
PWE3 Loopback Profile Entity. These profiles are used
by PWE3 T1/E1 interfaces. F3Pwe3LoopbackProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.3.1 |
f3Pwe3LoopbackProfileIndexUnique index value associated with the PWE3 Loopback Profile. Integer32 .1.3.6.1.4.1.2544.1.12.19.1.3.1.1 |
f3Pwe3LoopbackProfileLengthThis object allows SNMP management entities to specify the
PWE3 Loopback Length.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.3.1.2 |
f3Pwe3LoopbackProfilePatternThis object allows SNMP management entities to specify the
PWE3 Loopback Pattern.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.3.1.3 |
f3Pwe3LoopbackProfileRepeatTimeThis object allows SNMP management entities to specify the
PWE3 Loopback Profile Repeat Time (Duration).rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.3.1.4 |
f3Pwe3LoopbackProfileClearLengthThis object allows SNMP management entities to specify the
Loopback PWE3 Clear Length.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.3.1.5 |
f3Pwe3LoopbackProfileClearPatternThis object allows SNMP management entities to specify the
PWE3 Loopback Clear Pattern.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.3.1.6 |
f3Pwe3LossProfileTableA list of entries corresponding to the PWE3 Loss Profile entities. SEQUENCE OF F3Pwe3LossProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.4 |
f3Pwe3LossProfileEntryAn entry containing information applicable to a particular
PWE3 Loss Profile Entity. These profiles are used
by PWE3 SAToP entities. F3Pwe3LossProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.4.1 |
f3Pwe3LossProfileIndexUnique index value associated with the PWE3 Loss Profile. Integer32 .1.3.6.1.4.1.2544.1.12.19.1.4.1.1 |
f3Pwe3LossProfileLossStateEnterTimeThis object allows SNMP management entities to specify the
holdoff time that will be applied prior to the SAToP
instance entering a Loss State.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.4.1.2 |
f3Pwe3LossProfileLossStateExitTimeThis object allows SNMP management entities to specify the
holdon time that will be applied when the conditon causing
the loss state clears.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.4.1.3 |
f3Pwe3AisStabilizationProfileTableA list of entries corresponding to the PWE3 AisStabilization
Profile entities. SEQUENCE OF F3Pwe3AisStabilizationProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.5 |
f3Pwe3AisStabilizationProfileEntryAn entry containing information applicable to a particular
PWE3 AisStabilization Profile Entity. These profiles are used
by PWE3 SAToP entities. F3Pwe3AisStabilizationProfileEntry .1.3.6.1.4.1.2544.1.12.19.1.5.1 |
f3Pwe3AisStabilizationProfileIndexUnique index value associated with the PWE3 AIS
Stabilization Profile. Integer32 .1.3.6.1.4.1.2544.1.12.19.1.5.1.1 |
f3Pwe3AisStabilizationProfileEnterTimeThis object allows SNMP management entities to specify the
time (in hundreds of milliseconds) that will be applied on a
LOS event, before the SAToP instance transmits all 1s pattern
downstream (AIS).
Range 0 to 3 seconds in 100 millisecond increments.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.5.1.2 |
f3Pwe3AisStabilizationProfileExitTimeThis object allows SNMP management entities to specify the
holdon time that will be applied when leaving the AIS
Stabilization period.
Range 0 to 3 seconds in 100 milliseconds increments
(e.g. parameter range is 0 to 30).rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.5.1.3 |
f3Pwe3SatopTableA list of entries corresponding to the PWE3 SAToP entities. SEQUENCE OF F3Pwe3SatopEntry .1.3.6.1.4.1.2544.1.12.19.1.6 |
f3Pwe3SatopEntryAn entry containing information applicable to a particular
PWE3 SAToP Entity. F3Pwe3SatopEntry .1.3.6.1.4.1.2544.1.12.19.1.6.1 |
f3Pwe3SatopIndexUnique index value associated with the SAToP Entity. Integer32 .1.3.6.1.4.1.2544.1.12.19.1.6.1.1 |
f3Pwe3SatopAliasThis object allows SNMP management entities to provide an
alias to the PWE3 SAToP entity.rw DisplayString .1.3.6.1.4.1.2544.1.12.19.1.6.1.2 |
f3Pwe3SatopAdminStateThis object represents the Administrative State of the PWE3
SAToP entity.rw AdminState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.1.6.1.3 |
f3Pwe3SatopOperationalStateThis object represents the Operational State of the PWE3
SAToP entity.ro OperationalState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.1.6.1.4 |
f3Pwe3SatopSecondaryStateThis object represents the Secondary State of the PWE3
SAToP entity.ro SecondaryState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.1.6.1.5 |
f3Pwe3SatopTDMEntityThis object allows specification of the T1/E1 entity
associated with the SAToP. This is only used at
SATop creation time. Result of get operation on this object
will result with zeroDotZero since one Satop could have more
then one associated TDM entity. Subsequently, the associated
TDM entities are managed via f3Pwe3SatopTDMEntityTable.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.6 |
f3Pwe3SatopDiscoveryTypeThis object allows ability to statically/dynamically
determine the MAC address of the remote IP Address
associated with the SAToP. In the case of static discovery
type, f3Pwe3SatopRemoteMacAddress must be explicitly specified.
In the case of dynamic discovery, the system will use
ARP mechanism to obtain the remote Layer 2 MAC address.rw PWE3SatopDiscoveryType .1.3.6.1.4.1.2544.1.12.19.1.6.1.7 |
f3Pwe3SatopRemoteIpAddressThis object allows ability to specify the remote IP
Address. This is used in the PWE payload.rw IpAddress .1.3.6.1.4.1.2544.1.12.19.1.6.1.8 |
f3Pwe3SatopRemoteMacAddressThis object allows ability to specify the remote Layer 2
MAC Address. This must be specified in case of
f3Pwe3SatopDiscoveryType as static. This is derived
dynamically (via ARP) if f3Pwe3SatopDiscoveryType is dynamic,
i.e. it does not have to be specified.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.9 |
f3Pwe3SatopEncapsulationTypeThis object allows ability to specify the encapsulation
type of the SATop. It can be encapsulated with
VLAN and single MPLS label(vlan-one-mpls-label),
VLAN and two MPLS labels (vlan-two-mpls-label),
untagged and two MPLS labels (novlan-two-mpls-label)
.rw PWE3SatopEncapsulationType .1.3.6.1.4.1.2544.1.12.19.1.6.1.10 |
f3Pwe3SatopRTPEnabledThis object enables/disables RTP header for this SATop instance.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.11 |
f3Pwe3SatopRTPUpdateFrequencyWhen f3Pwe3SatopRTPEnabled is true, this object allows
specification of the RTP clock update frequency.rw PWE3SatopRTPTSUpdateFreqType .1.3.6.1.4.1.2544.1.12.19.1.6.1.12 |
f3Pwe3SatopControlWordEnabledThis object is used for 3rd party interoperability, since
earlier versions of PWE do not support control-word.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.13 |
f3Pwe3SatopJitterBufferSizeThis object allows definition of size of the jitter buffer
in microseconds for this SATop instance.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.6.1.14 |
f3Pwe3SatopPayloadSizeThis object allows specification of the SATop payload size.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.1.6.1.15 |
f3Pwe3SatopVlanIdThis object allows specification of the SATop VLAN Id.
Applicable for vlan based encapsulation types.rw VlanId (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.1.6.1.16 |
f3Pwe3SatopVlanPriorityThis object allows specification of the SATop VLAN Priority.
Applicable for vlan based encapsulation types.rw VlanPriority (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.1.6.1.17 |
f3Pwe3SatopRxMplsLabel1This object allows specification of the expected
receive MPLS Label.
Applicable for single MPLS label encapsulation type.rw MplsLabel .1.3.6.1.4.1.2544.1.12.19.1.6.1.18 |
f3Pwe3SatopRxMplsLabel2This object allows specification of the expected
receive MPLS Label.
Applicable for dual MPLS label encapsulation types.rw MplsLabel .1.3.6.1.4.1.2544.1.12.19.1.6.1.19 |
f3Pwe3SatopTxMplsLabel1This object allows specification of the transmitted
MPLS Label, used for multiplexing.
Applicable for single MPLS label encapsulation type.rw MplsLabel .1.3.6.1.4.1.2544.1.12.19.1.6.1.20 |
f3Pwe3SatopTxMplsLabel2This object allows specification of the transmitted
MPLS Label, used for multiplexing.
Applicable for dual MPLS label encapsulation type.rw MplsLabel .1.3.6.1.4.1.2544.1.12.19.1.6.1.21 |
f3Pwe3SatopAisStabilizationProfileThis object allows specification of the AIS stabilization
Profile object. If no profile is associated, this value should be
0.0.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.22 |
f3Pwe3SatopResyncProfileThis object allows specification of the Resync
Profile object. If no profile is associated, this value
should be 0.0.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.23 |
f3Pwe3SatopLossProfileThis object allows specification of the Loss
Profile object. If no profile is associated, this value
should be 0.0.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.24 |
f3Pwe3SatopTransportModeThis object allows specification of the SATop transport mode.rw PWE3SatopTransportMode .1.3.6.1.4.1.2544.1.12.19.1.6.1.25 |
f3Pwe3SatopStorageTypeThe type of storage configured for this entry.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.26 |
f3Pwe3SatopRowStatusThe status of this row. An entry MUST NOT exist in the
active state unless all objects in the entry have an
appropriate value, as described
in the description clause for each writable object.
The values of f3Pwe3SatopRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
f3Pwe3SatopRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The f3Pwe3SatopRowStatus object may be modified if
the associated instance of this object is equal to active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.6.1.27 |
f3Pwe3SatopTDMEntitiesTableA list of entries corresponding to the PWE3 SATop TDM entities
. SEQUENCE OF F3Pwe3SatopTDMEntitiesEntry .1.3.6.1.4.1.2544.1.12.19.1.7 |
f3Pwe3SatopTDMEntitiesEntryAn entry containing information applicable to a particular
PWE3 SATop TDM entity. F3Pwe3SatopTDMEntitiesEntry .1.3.6.1.4.1.2544.1.12.19.1.7.1 |
f3Pwe3SatopTDMEntityIndexUnique index value associated with the PWE3 SATOP TDM Entity. Integer32 .1.3.6.1.4.1.2544.1.12.19.1.7.1.1 |
f3Pwe3SatopTDMEntityObjectThis object points to the PWE3 SATOP TDM Entity. This is
OID of the actual T1/E1 interface.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.7.1.2 |
f3Pwe3SatopTDMEntityStorageTypeThe type of storage configured for this entry.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.7.1.3 |
f3Pwe3SatopTDMEntityRowStatusThe status of this row. An entry MUST NOT exist in the
active state unless all objects in the entry have an
appropriate value, as described
in the description clause for each writable object.
The values of f3Pwe3SatopTDMEntityRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
f3Pwe3SatopTDMEntityRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The f3Pwe3SatopTDMEntityRowStatus object may be modified if
the associated instance of this object is equal to active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.1.7.1.4 |
f3Pwe3PerformanceObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.19.2 |
f3Pwe3SatopStatsTableThe PWE3 SATop Current data. SEQUENCE OF F3Pwe3SatopStatsEntry .1.3.6.1.4.1.2544.1.12.19.2.1 |
f3Pwe3SatopStatsEntryA conceptual row in the f3Pwe3SatopStatsTable. F3Pwe3SatopStatsEntry .1.3.6.1.4.1.2544.1.12.19.2.1.1 |
f3Pwe3SatopStatsIndexAn index of the SATop current bin. Integer32 .1.3.6.1.4.1.2544.1.12.19.2.1.1.1 |
f3Pwe3SatopStatsIntervalTypeIndicates the type of collection, i.e. whether it is
15 Min, 1 Day.ro CmPmIntervalType (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.2 |
f3Pwe3SatopStatsValidIndicates the validity of the bin.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.2.1.1.3 |
f3Pwe3SatopStatsActionAllows the Manager to clear the bin.rw CmPmBinAction (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.4 |
f3Pwe3SatopStatsESsThe counter associated with the number
of Errored Seconds encountered by the
SATop in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.5 |
f3Pwe3SatopStatsSESsThe counter associated with the number of
Severely Errored Seconds encountered by the
SATop in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.6 |
f3Pwe3SatopStatsEBsThe counter associated with the number of
Errored Blocsk encountered by the SATop
in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.7 |
f3Pwe3SatopStatsResyncsThe counter associated with the number of
Resync count events encountered by the
SATop in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.8 |
f3Pwe3SatopStatsMaxJitterThe maximum absolute jitter on SATop in the current bin.ro Unsigned32 .1.3.6.1.4.1.2544.1.12.19.2.1.1.9 |
f3Pwe3SatopStatsFramesTxThe counter associated with the number of
Frames Transmitted in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.10 |
f3Pwe3SatopStatsPayloadOctetsTxThe counter associated with the number of
Payload Octets Transmitted in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.11 |
f3Pwe3SatopStatsFramesRxThe counter associated with the number of
Frames Received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.12 |
f3Pwe3SatopStatsPayloadOctetsRxThe counter associated with the number of
Payload Octets Received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.13 |
f3Pwe3SatopStatsOutOfSeqFramesRxThe counter associated with the number of
Out of Sequence Frames Received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.14 |
f3Pwe3SatopStatsLostFramesThe counter associated with the number of
Lost Frames detected in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.15 |
f3Pwe3SatopStatsLostFramesStateTransThe counter associated with the number of transitions to
Lost Frame State detected in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.16 |
f3Pwe3SatopStatsMalformedFramesRxThe counter associated with the number of
Malformed Frames received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.17 |
f3Pwe3SatopStatsJitterBufferLateFramesThe counter associated with the number of
Jitter Buffer Late Frames in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.1.1.18 |
f3Pwe3SatopHistoryTableThe PWE3 SATop History data. SEQUENCE OF F3Pwe3SatopHistoryEntry .1.3.6.1.4.1.2544.1.12.19.2.2 |
f3Pwe3SatopHistoryEntryA conceptual row in the f3Pwe3SatopHistoryTable. F3Pwe3SatopHistoryEntry .1.3.6.1.4.1.2544.1.12.19.2.2.1 |
f3Pwe3SatopHistoryIndexAn index of the SATop current bin. Integer32 .1.3.6.1.4.1.2544.1.12.19.2.2.1.1 |
f3Pwe3SatopHistoryTimeIndicates the time of history bin creation.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.2.2.1.2 |
f3Pwe3SatopHistoryValidIndicates the validity of the bin.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.2.2.1.3 |
f3Pwe3SatopHistoryActionAllows the Manager to clear the bin.rw CmPmBinAction (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.4 |
f3Pwe3SatopHistoryESsThe counter associated with the number
of Errored Seconds encountered by the
SATop in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.5 |
f3Pwe3SatopHistorySESsThe counter associated with the number of
Severely Errored Seconds encountered by the
SATop in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.6 |
f3Pwe3SatopHistoryEBsThe counter associated with the number of
Errored Blocsk encountered by the SATop
in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.7 |
f3Pwe3SatopHistoryResyncsThe counter associated with the number of
Resync count events encountered by the
SATop in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.8 |
f3Pwe3SatopHistoryMaxJitterThe maximum absolute jitter on SATop in the current bin.ro Unsigned32 .1.3.6.1.4.1.2544.1.12.19.2.2.1.9 |
f3Pwe3SatopHistoryFramesTxThe counter associated with the number of
Frames Transmitted in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.10 |
f3Pwe3SatopHistoryPayloadOctetsTxThe counter associated with the number of
Payload Octets Transmitted in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.11 |
f3Pwe3SatopHistoryFramesRxThe counter associated with the number of
Frames Received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.12 |
f3Pwe3SatopHistoryPayloadOctetsRxThe counter associated with the number of
Payload Octets Received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.13 |
f3Pwe3SatopHistoryOutOfSeqFramesRxThe counter associated with the number of
Out of Sequence Frames Received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.14 |
f3Pwe3SatopHistoryLostFramesThe counter associated with the number of
Lost Frames detected in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.15 |
f3Pwe3SatopHistoryLostFramesStateTransThe counter associated with the number of transitions to
Lost Frame State detected in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.16 |
f3Pwe3SatopHistoryMalformedFramesRxThe counter associated with the number of
Malformed Frames received in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.17 |
f3Pwe3SatopHistoryJitterBufferLateFramesThe counter associated with the number of
Jitter Buffer Overruns in the current bin.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.2.1.18 |
f3Pwe3SatopThresholdTableA table of entries that allow manageability of SATop
Thresholds. SEQUENCE OF F3Pwe3SatopThresholdEntry .1.3.6.1.4.1.2544.1.12.19.2.3 |
f3Pwe3SatopThresholdEntryA conceptual row in the f3Pwe3SatopThresholdTable. F3Pwe3SatopThresholdEntry .1.3.6.1.4.1.2544.1.12.19.2.3.1 |
f3Pwe3SatopThresholdIndexAn index that uniquely identifies an entry in the
f3Pwe3SatopThresholdTable. Integer32 .1.3.6.1.4.1.2544.1.12.19.2.3.1.1 |
f3Pwe3SatopThresholdIntervalThe interval over which monitored value is
sampled and compared with the specified threshold.ro CmPmIntervalType (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.19.2.3.1.2 |
f3Pwe3SatopThresholdVariableThe object identifier of the particular variable to be
sampled.ro VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.19.2.3.1.3 |
f3Pwe3SatopThresholdValueLoLower 32 bits of the threshold value.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.2.3.1.4 |
f3Pwe3SatopThresholdValueHiHigher 32 bits of the threshold value.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.19.2.3.1.5 |
f3Pwe3SatopThresholdMonValueMonitored value corresponding to f3Pwe3SatopThresholdVariable.ro Counter64 .1.3.6.1.4.1.2544.1.12.19.2.3.1.6 |
f3Pwe3PerformanceNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.19.3 |
f3Pwe3SatopThresholdCrossingAlertThis trap is sent each time a threshold on a PM condition
on an PWE3 SATop is crossed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.19.3.1 |
f3Pwe3Conformance OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.19.4 |
f3Pwe3Compliances OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.19.4.1 |
f3Pwe3Groups OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.19.4.2 |