F3-CFM-MIB
This module defines the CFM (8021AG) Extension MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
Main OID:
f3CfmMIB.1.3.6.1.4.1.2544.1.12.13
84
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
84 total| Object Name |
|---|
f3CfmMIBThis module defines the CFM (8021AG) Extension MIB definitions
used by the F3 (FSP150CM/CC) product lines.
Copyright (C) ADVA Optical Networking. MODULE-IDENTITY .1.3.6.1.4.1.2544.1.12.13 |
cfmExtSvc OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.13.1 |
cfmExtSvcObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.13.1.1 |
cfmExtScalars OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.13.1.1.1 |
cfmEthTypeThis object provides the system level Ethernet type for CFM.ro Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.1.1 |
cfmMacAddressThis object provides the system level Mac address for CFM.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.1.2 |
slmMulticastMacAddressThis object can be used to configure the Synthetic Loss Measurement(SLM)
Multicast MAC Address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.1.3 |
slmOpcodeThis object can be used to configure the Operation Code for the
Synthetic Loss Measurement(SLM) message.rw Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.1.4 |
slrOpcodeThis object can be used to configure the Operation Code for the
Synthetic Loss Response(SLR) message.rw Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.1.5 |
cfmSignalFailTriggersThis object can be used to configure the list of defects which constitute
Signal Fail condition.rw CfmSignalFailTriggers .1.3.6.1.4.1.2544.1.12.13.1.1.1.6 |
cfmMepTableAdditional MEP configuration such as Y.1731 configuration. SEQUENCE OF CfmMepEntry .1.3.6.1.4.1.2544.1.12.13.1.1.2 |
cfmMepEntryA list of additional MEP parameters such the Y.1731 parameters. CfmMepEntry .1.3.6.1.4.1.2544.1.12.13.1.1.2.1 |
cfmMepAdminStateThis object represents the Administrative State of the CFM MEPs.rw AdminState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.1 |
cfmMepAisGenTriggerTypesA bit mask which indicates all the defects that result in triggering
an AIS for the higher level MEP or transmission of ETH-AIS.rw CfmAisGenTriggerTypes .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.2 |
cfmMepAisClientMdLevelAIS Client MD level which is the MD level used to identify any
higher level local MEPs for which AIS defect needs to be set or
MD level of the ETH-AIS frame generated if there are no local MEPs
at this MD level.rw Dot1agCfmMDLevel .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.3 |
cfmMepAisIntervalETH-AIS frame transmission interval if decision is made to transmit the
ETH-AIS frame.rw CfmAisInterval .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.4 |
cfmMepAisGenEnabledThis flag enables/disables propagation of ETH-AIS to client MD levels.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.5 |
cfmMepAisPriorityThis VLAN priority of the ETH-AIS frame.rw VlanPriority (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.6 |
cfmMepLmTxCountAllPriosEnabledThis attribute is used when Y.1731 probes are created and LMM frames
are transmitted. As per Y.1731, loss measurement should be done per
priority class. The implementation is restricted to support counting
of frames for only one priority that can be modified. As an added
value there is an option to count all priorities. This flag is used
to decide whether to put cumulative data frame counts for all the
priorities into the LMM that is transmitted by the MEP instead of
data frame counts for a provisioned individual priority.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.7 |
cfmMepLmRxCountAllPriosEnabledThis attribute is used when Y.1731 probes are created and LMR frames
are transmitted. As per Y.1731, loss measurement should be done per
priority class. The implementation is restricted to support counting
of frames for only one priority that can be modified. As an added
value there is an option to count all priorities. This flag is used
to decide whether to put cumulative data frame counts for all the
priorities into the LMR that is transmitted by the MEP instead of
data frame counts for a provisioned individual priority. LMR is sent
by a MEP when an LMM is received.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.8 |
cfmMepLmDualEndedCountAllPriosEnabledThis attribute is used when Y.1731 probes are created and CCM frames
are transmitted with loss measurement counts. As per Y.1731, loss
measurement should be done per priority class. The implementation is
restricted to support counting of frames for only one priority that
can be modified. As an added value there is an option to count all
priorities. This flag is used to decide whether to put cumulative
data frame counts for all the priorities into the CCM instead of
data frame counts for a provisioned individual priority.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.9 |
cfmMepLmCountInProfileEnabledAs per the Y.1731 data frames counted for loss measurement shall be
in-profile (green) data frames. As an added value, this flag is
provided for the device to count all frames instead of green frames
only. This flag could be set to false in cases where the remote
device is not color aware and/or capable of color marking. Even
if the device is capable of color marking and is color aware if the
outer tag is not an S-TAG it makes sense to set this flag to false.
As defined in IEEE 802.1ad the S-TAG has the drop eligibility bit
that is used to mark the frames green or yellow.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.10 |
cfmMepLmTxPriorityThis attribute is used if cfmMepLmTxCountAllPrios is false.
This attribute serves three purposes:
- It is the VLAN priority of the LMM.
- Data frames transmitted and received with this VLAN priority
are counted by the MEP. The transmit count is sent in the LMM
and the receive count is used to complete the list of four
counts used for the loss measurement.
- If an LMR is received with a VLAN priority other than this
the LMR is dropped.rw VlanPriority (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.11 |
cfmMepDmPriorityThis attribute specifies the DMM frame VLAN priority.rw VlanPriority (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.12 |
cfmMepRxCCMsThis provides the total number of received CCMs on the MEP.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.13 |
cfmMepErrCCMsThis provides the total number of errored CCMs on the MEP.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.14 |
cfmMepLLFTriggerTypesThis bit mask indicates the CFM triggers that result in link loss
forwarding.rw CfmLLFTriggerTypes .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.15 |
cfmMepDefectsThis bit mask indicates defects that not defined in standard 802.1ag
MIB such as AIS defect.ro CfmMepDefects .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.16 |
cfmMepTagEtherTypeThis object allows management of Ether Type for MEP VLAN Tag for the MEPs.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.17 |
cfmMepStatsActionAllows the Manager to clear the CFM level
statistics : cfmMepRxCCMs, cfmMepErrCCMs.rw CmPmBinAction (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.18 |
cfmMepLbmIntervalETH-LBM frame transmission interval.rw Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.19 |
cfmMepOperationalStateThis object represents the Operational State of the CFM MEP.ro OperationalState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.20 |
cfmMepSecondaryStateThis object represents the Secondary State of the CFM MEP.ro SecondaryState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.21 |
cfmMepSlmEnabledThis bit mask indicates the whether SLM is enabled per each COS.rw CfmSlmEnabledTypes .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.22 |
cfmMepAssociatedObjectThis object represents the associated port, it could be port, flow or flow point.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.2.1.23 |
cfmAccPortQosShaperTableA list of configurable profile entries for CFM QoS Shapers for Access Port. SEQUENCE OF CfmAccPortQosShaperEntry .1.3.6.1.4.1.2544.1.12.13.1.1.3 |
cfmAccPortQosShaperEntryA list of parameters that set up the CFM QoS Queue profiles.
This shaper is created automatically when the first Down MEP
is created on a Access Port. CfmAccPortQosShaperEntry .1.3.6.1.4.1.2544.1.12.13.1.1.3.1 |
cfmAccPortQosShaperIndexA unique index associated with the type of Access Port Based Shaper.
Index 1 refers to the Shaper associated with PORT-based Down MEPs,
Index 2 refers to the Shaper associated with the VID-based Down MEPs. Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.3.1.1 |
cfmAccPortQosShaperCIRThis object identifies the queue CIR.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.3.1.2 |
cfmAccPortQosShaperBufSizeThis object identifies the queue buffer size.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.3.1.3 |
cfmAccPortQosShaperAdminStateThis object allows the management of the Shaper Administrative State.
Only 'in-service' and 'management' states are allowed.rw AdminState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.3.1.4 |
cfmNetPortQosShaperTableA list of configurable profile entries for CFM QoS Shapers for Network Port. SEQUENCE OF CfmNetPortQosShaperEntry .1.3.6.1.4.1.2544.1.12.13.1.1.4 |
cfmNetPortQosShaperEntryA list of parameters that set up the CFM QoS Queue profiles.
This shaper is created automatically when the first Down MEP
is created on a Network Port. CfmNetPortQosShaperEntry .1.3.6.1.4.1.2544.1.12.13.1.1.4.1 |
cfmNetPortQosShaperTypeIndexA unique index associated with the type of Network Port Based Shaper.
Index 1 refers to the Shaper associated with PORT-based Down MEPs,
Index 2 refers to the Shaper associated with the VID-based Down MEPs. Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.4.1.1 |
cfmNetPortQosShaperCIRThis object identifies the queue CIR.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.4.1.2 |
cfmNetPortQosShaperBufSizeThis object identifies the queue buffer size.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.4.1.3 |
cfmNetPortQosShaperAdminStateThis object allows the management of the Shaper Administrative State.
Only 'in-service' and 'management' states are allowed.rw AdminState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.4.1.4 |
cfmServerMepTableServer MEP management table. SEQUENCE OF CfmServerMepEntry .1.3.6.1.4.1.2544.1.12.13.1.1.5 |
cfmServerMepEntryThis allows management of Server MEPs. CfmServerMepEntry .1.3.6.1.4.1.2544.1.12.13.1.1.5.1 |
cfmServerMepIndexThe integer index value corresponding to a Server MEP.rw Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.1 |
cfmServerMepAssociatedPortThis is the port on which the CFM Server MEP is created.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.2 |
cfmServerMepAisClientMdLevelAIS Client MD level which is the MD level used to identify any
higher level local MEPs for which AIS defect needs to be set or
MD level of the ETH-AIS frame generated if there are no local MEPs
at this MD level.rw Dot1agCfmMDLevel .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.3 |
cfmServerMepAisIntervalETH-AIS frame transmission interval if decision is made to transmit the
ETH-AIS frame.rw CfmAisInterval .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.4 |
cfmServerMepAisGenEnabledThis flag enables/disables propagation of ETH-AIS to client MD levels.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.5 |
cfmServerMepAisPriorityThis VLAN priority of the ETH-AIS frame.rw VlanPriority (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.6 |
cfmServerMepStorageTypeThe type of storage configured for this entry.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.7 |
cfmServerMepRowStatusThe status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value, as described
in the description clause for each writable object.
The values of cfmServerMepRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
cfmServerMepRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The cfmServerMepRowStatus object may be modified if
the associated instance of this object is equal to active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.8 |
cfmServerMepAdminStateThis object represents the Administrative State of the Server MEP.rw AdminState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.9 |
cfmServerMepOperationalStateThis object represents the Operational State of the Server MEP.ro OperationalState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.10 |
cfmServerMepSecondaryStateThis object represents the Secondary State of the CFM MEP.ro SecondaryState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.5.1.11 |
cfmDownMEPQosShaperTableA list of configurable profile entries for CFM QoS Shapers for down MEPs. SEQUENCE OF CfmDownMEPQosShaperEntry .1.3.6.1.4.1.2544.1.12.13.1.1.6 |
cfmDownMEPQosShaperEntryA list of parameters that set up the CFM QoS Queue profiles.
This shaper is created automatically when the first Down MEP
is created on a Port. Note, this queues is valid for port based Down MEPs, VID based down MEPs on NNI port. CfmDownMEPQosShaperEntry .1.3.6.1.4.1.2544.1.12.13.1.1.6.1 |
cfmDownMEPQosShaperIndexA unique index associated with the Shaper for Down MEPs. Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.6.1.1 |
cfmDownMEPQosShaperTypeType of Shaper for Down MEPs.
1 refers to the Shaper associated with Down MEPs(for both port based and VID based) fot Transimit direction,
2 refers to the Shaper associated with Down MEPs(for both port based and VID based) fot Receiving directionro Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.6.1.2 |
cfmDownMEPQosShaperCIRThis object identifies the queue CIR.rw Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.6.1.3 |
cfmDownMEPQosShaperProfileThis object identifies the OID of cmQosQueueProfileIndex in the cmQosQueueProfileTable.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.6.1.4 |
cfmDownMEPQosShaperAdminStateThis object allows the management of the Shaper Administrative State.
Only 'in-service' and 'management' states are allowed.rw AdminState (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.6.1.5 |
cfmMepExcludedMepListTableA list of configurable profile entries for CFM excluded mep list. SEQUENCE OF CfmMepExcludedMepListEntry .1.3.6.1.4.1.2544.1.12.13.1.1.7 |
cfmMepExcludedMepListEntryExcluded Remote Mep List for local Mep, not expected to receive OAM from these MEPs. CfmMepExcludedMepListEntry .1.3.6.1.4.1.2544.1.12.13.1.1.7.1 |
cfmMepExcludedMepListIdentifierA unique index associated with CfmMepExcludedMepListEntry. Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.7.1.1 |
cfmMepExcludedMepListRowStatusThe status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value, as described
in the description clause for each writable object.
The values of cfmMepExcludedMepListRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
cfmMepExcludedMepListRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The cfmMepExcludedMepListRowStatus object may be modified if
the associated instance of this object is equal to active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.7.1.2 |
cfmMepLbrTableA list of configurable profile entries for MepLbr. SEQUENCE OF CfmMepLbrEntry .1.3.6.1.4.1.2544.1.12.13.1.1.8 |
cfmMepLbrEntryMEP LBR statistic table. CfmMepLbrEntry .1.3.6.1.4.1.2544.1.12.13.1.1.8.1 |
cfmMepLbrMacAddressSource Mac Address of LBR.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.8.1.1 |
cfmMepLbrMepIdRemote MEP ID.ro Integer32 .1.3.6.1.4.1.2544.1.12.13.1.1.8.1.2 |
cfmMepLbrInOrderTotal valid in-order LBR received.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.8.1.3 |
cfmMepLbrOutOfOderTotal valid out of order LBR received.ro PerfCounter64 (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.13.1.1.8.1.4 |
cfmMaCompTableA additional list of MA components. SEQUENCE OF CfmMaCompEntry .1.3.6.1.4.1.2544.1.12.13.1.1.9 |
cfmMaCompEntryA list of additional maCompEntry. CfmMaCompEntry .1.3.6.1.4.1.2544.1.12.13.1.1.9.1 |
cfmMaCompIndexThis object represents the maComp number value.ro Unsigned32 .1.3.6.1.4.1.2544.1.12.13.1.1.9.1.1 |
cfmMaCompEntityThis object represents the maComp entity, it is should be port or flow's oid.rw VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.13.1.1.9.1.2 |
cfmExtSvcConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.13.1.2 |
cfmExtSvcCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.13.1.2.1 |
cfmExtSvcGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.13.1.2.2 |