EXTREME-QOS-MIB
Extreme Quality-of-Service objects
Main OID:
extremeQos.1.3.6.1.4.1.1916.1.3
42
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
42 total| Object Name |
|---|
extremeQosExtreme Quality-of-Service objects MODULE-IDENTITY .1.3.6.1.4.1.1916.1.3 |
SNMPv2-SMIExtreme Quality-of-Service objects Unknown .1.3.6.1.4.1.1916.1.3 |
extremeQosCommon OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.3.1 |
extremeUnitPaceModeThis object specifies whether the device currently
recognises and gives priority treatment to the
forwarding of packets with the PACE(tm) bit set in
their MAC Source Address fields.
PACE(tm) mode applies to the whole unit only and
is only valid when device is in Ingress QoS mode
as specified by extremeQosMode ingress(1). This
object will report notApplicable(1) when in
egress(2) mode. Set operations with value
notApplicable(1) will be rejected.rwdeprecated Enumeration .1.3.6.1.4.1.1916.1.3.1.1 |
extremeQosModeIndicates which QoS mode the device should
use. ingress(1) applies priority-based QoS based
on the incoming packet's destination IP or MAC
address, 802.1p priority, PACE(tm), Source Port or
VLAN. egress(2) applies priority- and bandwidth-based
QoS based on destination IP or MAC address or VLAN.
See ExtremeWare documentation for further information.rwdeprecated Enumeration .1.3.6.1.4.1.1916.1.3.1.4 |
extremeQosUnconfigureSetting this to true will reset all QoS settings
in the device to factory defaults. Reads from this
value return an undefined value.rwdeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.3.1.5 |
extremeQosProfileTableThis table lists QoS profiles. SEQUENCE OF ExtremeQosProfileEntry .1.3.6.1.4.1.1916.1.3.1.6 |
extremeQosProfileEntryAn individual QoS profile Entry. ExtremeQosProfileEntry .1.3.6.1.4.1.1916.1.3.1.6.1 |
extremeQosProfileIndexAn index that uniquely identifies an entry in the
qos table.rw INTEGER .1.3.6.1.4.1.1916.1.3.1.6.1.1 |
extremeQosProfileNameA unique qos profile name.rw DisplayString .1.3.6.1.4.1.1916.1.3.1.6.1.2 |
extremeQosProfileMinBwThe minumum percentage of bandwidth that this queue requires.
The Switch is required to provide the minumum amount of
bandwidth to the queue. The lowest possible value is 0%.rw INTEGER .1.3.6.1.4.1.1916.1.3.1.6.1.3 |
extremeQosProfileMaxBwThe maximum percentage of bandwidth that this queue is
permitted to use.
If a non-default value is set for this object then it negates
any previously set value of extremeQosProfileMaxSustBwBps. In
In addition, a set operation that supplies non-default values
for both this object and for extremeQosProfileMaxSustBwBps
will be rejected by the agent. In other words, you may supply
either an absolute or a percent limit, not both.rw INTEGER .1.3.6.1.4.1.1916.1.3.1.6.1.4 |
extremeQosProfilePriorityThe level of priority in which this queue will be
serviced by the Switch.rw Enumeration .1.3.6.1.4.1.1916.1.3.1.6.1.5 |
extremeQosProfileRowStatusThe status of the extremeQosProfile entry.
This object can be set to:
active(1)
createAndGo(4)
createAndWait(5)
destroy(6)
The following values may be read:
active(1)
notInService(2)
notReady(3).
Setting this object to createAndGo(4) causes the agent
to attempt to create and commit the row based on
the contents of the objects in the row. If all necessary
information is present in the row and the values are
acceptible to the agent, the agent will change the
status to active(1). If any of the necessary objects
are not available, the agent will reject the creation
request.
Setting this object to createAndWait(5) causes a row
in this table to be created. The agent sets the
status to notInService(2) if all of the information is
present in the row and the values are acceptable to the
agent; otherwise, the agent sets the status to notReady(3).
Setting this object to active(1) is only valid when
the current status is active(1) or notInService(2).
When the state of the row transitions is set to active(1),
the agent creates the corresponding row in the ifTable..
Setting this object to destroy(6) will remove the
corresponding QoS Profile Entry.
In order for a set of this object to destroy(6) to succeed,
all dependencies on this row must have been removed. These
will include any stacking dependencies in the ifStackTable
and any protocol specific tables dependencies.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.3.1.6.1.6 |
extremeQosByVlanMappingTableTable to associate a Vlan with the QoS profile that the
Vlan is using. Every Vlan is assigned a Qos Profile and
hence there is an entry in this table corresponding to every
entry in the extremeVlanIfTable. SEQUENCE OF ExtremeQosByVlanMappingEntry .1.3.6.1.4.1.1916.1.3.1.7 |
extremeQosByVlanMappingEntryThe QoS associated with a particular Vlan. ExtremeQosByVlanMappingEntry .1.3.6.1.4.1.1916.1.3.1.7.1 |
extremeQosByVlanMappingQosProfileIndexValue of extremeQosProfileIndex that uniquely
identifies a QoS Profile entry in extremeQosProfileTable.
This indicates the QoS to be given to traffic for this
Vlan in the absence of any other more specific
configuration information for this traffic.rw INTEGER .1.3.6.1.4.1.1916.1.3.1.7.1.1 |
extremePerPortQosTableGlobal Qos Profiles are defined in the
extremeQosProfileTable. This table contains a list
of ports for which the definition of certain global
Qos Profiles has been overridden. The new definition
of the Qos profile parameters is in this table. SEQUENCE OF ExtremePerPortQosEntry .1.3.6.1.4.1.1916.1.3.1.8 |
extremePerPortQosEntryAn individual overridden QoS profile Entry. ExtremePerPortQosEntry .1.3.6.1.4.1.1916.1.3.1.8.1 |
extremePerPortQosIndexThe value of this variable is the same as the value
of extremeQosProfileIndex of the Qos Profile which
is overridden (for the port specified by ifIndex) by
the definition in this table.rw INTEGER .1.3.6.1.4.1.1916.1.3.1.8.1.1 |
extremePerPortQosMinBwThe minumum percentage of bandwidth that this queue on the
specified port requires. The Switch is required to provide
the minumum amount of bandwidth to the queue. The lowest
possible value is 0%.rw INTEGER .1.3.6.1.4.1.1916.1.3.1.8.1.2 |
extremePerPortQosMaxBwThe maximum percentage of bandwidth that this queue on the
specified port is permitted to use.rw INTEGER .1.3.6.1.4.1.1916.1.3.1.8.1.3 |
extremePerPortQosPriorityThe level of priority in which this queue will be
serviced by the Switch.rw Enumeration .1.3.6.1.4.1.1916.1.3.1.8.1.4 |
extremePerPortQosRowStatusThe status of the extremePerPortQos entry.
This object can be set to
active(1)
createAndGo(4)
The following value may be read:
active(1)
Note that a destroy(6) is not supported. A row will only be
deleted from this table when the Qos Profile indicated
in that row is changed globally.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.3.1.8.1.5 |
extremeQosIngressPriorityTableThis table lists QoS ingress priority settings. SEQUENCE OF ExtremeQosIngressPriorityEntry .1.3.6.1.4.1.1916.1.3.1.9 |
extremeQosIngressPriorityEntryAn individual QoS ingress priority Entry. ExtremeQosIngressPriorityEntry .1.3.6.1.4.1.1916.1.3.1.9.1 |
extremeQosIngressPriorityIndexAn index that uniquely identifies an entry in the
qos ingress priority table.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.9.1.1 |
extremeQosIngressPriorityNameA qos ingress priority name.ro DisplayString .1.3.6.1.4.1.1916.1.3.1.9.1.2 |
extremeQosIngressPriorityValueThe ingress Qos priority value.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.9.1.3 |
extremeIQosProfileTableThis table lists ingress QoS profiles. SEQUENCE OF ExtremeIQosProfileEntry .1.3.6.1.4.1.1916.1.3.1.10 |
extremeIQosProfileEntryAn individual ingress QoS profile Entry. ExtremeIQosProfileEntry .1.3.6.1.4.1.1916.1.3.1.10.1 |
extremeIQosProfileIndexAn index that uniquely identifies an entry in the
ingress Qos table.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.10.1.1 |
extremeIQosProfileNameA unique ingress Qos profile name.ro DisplayString .1.3.6.1.4.1.1916.1.3.1.10.1.2 |
extremeIQosProfileMinBwTypeThe type of the current minimum bandwith setting. A value
of 1 signifies that the minimum bandwith value is a percentage
of the configurable port bandwidth. A value of 2 or 3 signifies
a guaranteed minimum available bandwidth in Kbps or Mbps
respectively.ro Enumeration .1.3.6.1.4.1.1916.1.3.1.10.1.3 |
extremeIQosProfileMinBwThe guaranteed minimum bandwidth for this queue, expressed as either
a percentage or a specific bandwidth value, as specified by the value
of extremeIQosProfileMinBwType.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.10.1.4 |
extremeIQosProfileMaxBwTypeThe type of the current maximum bandwith setting. A value
of 1 signifies that the maximum bandwith value is a percentage
of the configurable port bandwidth. A value of 2 or 3 signifies
a maximum allowed bandwidth in Kbps or Mbps respectively.ro Enumeration .1.3.6.1.4.1.1916.1.3.1.10.1.5 |
extremeIQosProfileMaxBwThe maximum allowed input bandwidth for this queue, expressed as
either a percentage or a specific bandwidth value, as specified by
the value of extremeIQosProfileMaxBwType.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.10.1.6 |
extremeIQosProfileREDThe Random Early Drop threshold. When the input queue fill
ratio exceeds this percentage, frames start to drop randomly
with a linear increasing drop probability as the queue fill
count approaches the max queue size. A value of 100 indicates
that this feature is currently disabled.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.10.1.7 |
extremeIQosProfileMaxBufThe percentage of the total ingress queue size to use. Lower values
can be used to reduce the max latency through this queue, but with
potentially greater loss with bursty traffic.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.10.1.8 |
extremeIQosByVlanMappingTableTable to associate a Vlan with the ingress QoS profile
that the Vlan is using. Every Vlan is assigned a Qos Profile
and hence there is an entry in this table corresponding to
every entry in the extremeVlanIfTable. SEQUENCE OF ExtremeIQosByVlanMappingEntry .1.3.6.1.4.1.1916.1.3.1.11 |
extremeIQosByVlanMappingEntryThe ingress QoS associated with a particular Vlan. ExtremeIQosByVlanMappingEntry .1.3.6.1.4.1.1916.1.3.1.11.1 |
extremeIQosByVlanMappingIQosProfileIndexValue of extremeIQosProfileIndex that uniquely
identifies an ingress QoS Profile entry in extremeIQosProfileTable.
This indicates the QoS to be given to traffic for this
Vlan in the absence of any other more specific
configuration information for this traffic.ro INTEGER .1.3.6.1.4.1.1916.1.3.1.11.1.1 |