EXTREME-VLAN-MIB
AI MIB Summary
The EXTREME-VLAN-MIB provides SNMP access to configure and monitor Virtual LAN (VLAN) parameters, including port assignments, VLAN membership states, and bridging statistics on Extreme Networks switching hardware. This module enables the tracking of VLAN operational status, MAC address table entries, and traffic counters essential for Layer 2 network segmentation and troubleshooting.
Extreme Virtual LAN objects
Main OID:
extremeVlan.1.3.6.1.4.1.1916.1.2
120
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
120 total| Object Name |
|---|
extremeVlanExtreme Virtual LAN objects MODULE-IDENTITY .1.3.6.1.4.1.1916.1.2 |
RFC1213-MIBExtreme Virtual LAN objects Unknown .1.3.6.1.4.1.1916.1.2 |
extremeVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.1 |
extremeVlanGlobalMappingTableThis table lists VLAN interfaces that are globally
identified. A single entry exists in this list for
each VLAN interface in the system that is bound to
a global identifier.deprecated SEQUENCE OF ExtremeVlanGlobalMappingEntry .1.3.6.1.4.1.1916.1.2.1.1 |
extremeVlanGlobalMappingEntryAn individual VLAN interface global mapping entry.
Entries in this table are created by setting the
extremeVlanIfGlobalIdentifier object in the
extremeVlanIfTable to a non-zero value. ExtremeVlanGlobalMappingEntry .1.3.6.1.4.1.1916.1.2.1.1.1 |
extremeVlanGlobalMappingIdentifierAn index into the extremeVlanGlobalMappingTable and an
administratively assigned global VLAN identifier. The
value of this object globally identifies the VLAN interface.
For VLAN interfaces, on different network devices, which are
part of the same globally identified VLAN, the value of this
object will be the same.ro INTEGER .1.3.6.1.4.1.1916.1.2.1.1.1.1 |
extremeVlanGlobalMappingIfIndexThe value of extremeVlanIfIndex for the VLAN interface in the
extremeVlanIfTable, which is bound to the global identifier
specified by this entry.ro Integer32 .1.3.6.1.4.1.1916.1.2.1.1.1.2 |
extremeVlanIfTableThis table lists VLAN interfaces that exist within
a device. A single entry exists in this list for each
VLAN interface in the system. A VLAN interface may
be created, destroyed and/or mapped to a globally
identified vlan. SEQUENCE OF ExtremeVlanIfEntry .1.3.6.1.4.1.1916.1.2.1.2 |
extremeVlanIfEntryAn individual VLAN interface entry. When an NMS wishes
to create a new entry in this table, it must obtain a
non-zero index from the extremeNextAvailableVirtIfIndex
object. Row creation in this table will fail if the
chosen index value does not match the current value
returned from the extremeNextAvailableVirtIfIndex object. ExtremeVlanIfEntry .1.3.6.1.4.1.1916.1.2.1.2.1 |
extremeVlanIfIndexThe index value of this row and the vlan's ifIndex in the
ifTable. The NMS obtains the index value for this row by
reading the extremeNextAvailableVirtIfIndex object.rw Integer32 .1.3.6.1.4.1.1916.1.2.1.2.1.1 |
extremeVlanIfDescrThis is a description of the VLAN interface.rw DisplayString .1.3.6.1.4.1.1916.1.2.1.2.1.2 |
extremeVlanIfTypeThe VLAN interface type.rw ExtremeVlanType .1.3.6.1.4.1.1916.1.2.1.2.1.3 |
extremeVlanIfGlobalIdentifierAn administratively assigned global VLAN identifier. For
VLAN interfaces, on different network devices, which are
part of the same globally identified VLAN, the value of this
object will be the same.
The binding between a global identifier and a VLAN
interface can be created or removed. To create a binding
an NMS must write a non-zero value to this object. To
delete a binding, the NMS must write a zero to this
object. The value 1 is reserved for the default VLAN and
this cannot be deleted or re-assigned.rwdeprecated INTEGER .1.3.6.1.4.1.1916.1.2.1.2.1.4 |
extremeVlanIfStatusThe status column for this VLAN interface.
This OBJECT can be set to:
active(1)
createAndGo(4)
createAndWait(5)
destroy(6)
The following values may be read:
active(1)
notInService(2)
notReady(3).
Setting this object to createAndGo(4) causes the agent
to attempt to create and commit the row based on
the contents of the objects in the row. If all necessary
information is present in the row and the values are
acceptible to the agent, the agent will change the
status to active(1). If any of the necessary objects
are not available, the agent will reject the creation
request.
Setting this object to createAndWait(5) causes a row
in this table to be created. The agent sets the
status to notInService(2) if all of the information is
present in the row and the values are acceptable to the
agent; otherwise, the agent sets the status to notReady(3).
Setting this object to active(1) is only valid when
the current status is active(1) or notInService(2).
When the state of the row transitions is set to active(1),
the agent creates the corresponding row in the ifTable.
Setting this object to destroy(6) will remove the
corresponding VLAN interface, remove the entry in this
table, and the corresponding entries in the
extremeVlanGlobalMappingTable and the ifTable.
In order for a set of this object to destroy(6) to succeed,
all dependencies on this row must have been removed. These
will include any stacking dependencies in the ifStackTable
and any protocol specific tables dependencies.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.1.2.1.6 |
extremeVlanIfIgnoreStpFlagEnable/disable STP for this VLAN interface. Setting this
object to true will cause the ports on this VLAN to ignore
STP BPDUs. When a vlan is first created, the Default value
is FALSE, which means that the VLAN uses STP port informationrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.1.2.1.7 |
extremeVlanIfIgnoreBpduFlagSetting this object to true causes this VLAN's BPDU's to be ignored by
the Spanning Tree process. This can be used to keep the root bridge within
one's own network when external switches also fall within the same Spanning
Tree Domain. When a vlan is first created, the Default value is FALSE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.1.2.1.8 |
extremeVlanIfLoopbackModeFlagSetting this object to true causes loopback mode to be enabled on this VLAN.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.1.2.1.9 |
extremeVlanIfVlanIdThe VLAN ID of this VLAN.rw Integer32 .1.3.6.1.4.1.1916.1.2.1.2.1.10 |
extremeVlanIfEncapsTypeThe encapsulation algorithm used when encapsulating
packets transmitted, or de-encapsulating packets
received through this interface.rw ExtremeVlanEncapsType .1.3.6.1.4.1.1916.1.2.1.2.1.11 |
extremeVlanIfAdminStatusEnable/disable this VLAN interface. Setting this
object to true will administratively enable this VLAN.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.1.2.1.12 |
extremeVirtualGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.2 |
extremeNextAvailableVirtIfIndexThe value of the next available virtual ifIndex. This
object is used by an NMS to select an index value
for row-creation in tables indexed by ifIndex. The
current value of this object is changed to a new
value when the current value is written to an agent's
table, that is indexed by ifIndex. Row creation
using the current value of this object, allocates
a virtual ifIndex. Note the following:
1. A newly created row does not have to be active(1)
for the agent to allocate the virtual ifIndex.
2. Race conditions between multiple NMS's end when
a row is created. Rows are deemed created when
a setRequest is successfully committed (i.e.
the errorStats is noError(0)).
3. An agent that exhausts its supply of virual
ifIndex values returns zero as the value of this
object. This can be used by an NMS as an indication
to deleted unused rows and reboot the device.ro Integer32 .1.3.6.1.4.1.1916.1.2.2.1 |
extremeEncapsulationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.3 |
extremeVlanEncapsIfTableThis table lists VLAN encapsulation interfaces that
exist within a device. A single entry exists in this
list for each VLAN encapsulation interface in the
system. A VLAN encapsulation interface may be created
or destroyed. SEQUENCE OF ExtremeVlanEncapsIfEntry .1.3.6.1.4.1.1916.1.2.3.1 |
extremeVlanEncapsIfEntryAn individual VLAN encapsulation interface entry.
When an NMS wishes to create a new entry in this table,
it must obtain a non-zero index from the
extremeNextAvailableVirtIfIndex object. Row creation
in this table will fail if the chosen index value does
not match the current value returned from the
extremeNextAvailableVirtIfIndex object. ExtremeVlanEncapsIfEntry .1.3.6.1.4.1.1916.1.2.3.1.1 |
extremeVlanEncapsIfIndexThe index value of this row and the encapsulation
interface's ifIndex in the ifTable. The NMS obtains
the index value used for creating a row in this table
by reading the extremeNextAvailableVirtIfIndex object.rw Integer32 .1.3.6.1.4.1.1916.1.2.3.1.1.1 |
extremeVlanEncapsIfTypeThe encapsulation algorithm used when encapsulating
packets transmitted, or de-encapsulating packets
received through this interface.rw ExtremeVlanEncapsType .1.3.6.1.4.1.1916.1.2.3.1.1.2 |
extremeVlanEncapsIfTagThe tag used when encapsulating packets transmitted,
or de-encapsulating packets received through this
interface.rw Integer32 .1.3.6.1.4.1.1916.1.2.3.1.1.3 |
extremeVlanEncapsIfStatusThe row status for this VLAN encapsulation interface.
This OBJECT can be set to:
active(1)
createAndGo(4)
createAndWait(5)
destroy(6)
The following values may be read:
active(1)
notReady(3).
In order for a row to become active, the NMS must set
extremeVlanEncapsIfTagType and extremeVlanEncapsIfTag
to some valid and consistent values.
Setting this object to createAndGo(4) causes the agent
to attempt to create and commit the row based on the
contents of the objects in the row. If all necessary
information is present in the row, the agent will
create the row and change the status to active(1). If
any of the necessary objects are not available, or
specify an invalid configuration, the row will not be
created and the agent will return an appropriate error.
Setting this object to createAndWait(5) causes a row in
in this table to be created. If all necessary objects
in the row have been assigned values and specify a
valid configuration, the status of the row will be set
to notInService(2); otherwise, the status will be set
to notReady(3).
This object may only be set to createAndGo(4) or
createAndWait(5) if it does not exist.
Setting this object to active(1) when the status is
notInService(2) causes the agent to commit the
row. Setting this object to active(1) when its value
is already active(1) is a no-op.
Setting this object to destroy(6) will remove the
corresponding VLAN encapsulation interface, remove the
entry in this table, and remove the corresponding entry
in the ifTable.
In order for a set of this object to destroy(6) to
succeed, all dependencies on this row must have been
removed. These will include any references to this
interface in the ifStackTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.3.1.1.4 |
extremeVlanIpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.4 |
extremeVlanIpTableA list of IP VLAN interface information
entries. Entries in this table are related
to entries in the extremeVlanIfTable by using the
same index. SEQUENCE OF ExtremeVlanIpEntry .1.3.6.1.4.1.1916.1.2.4.1 |
extremeVlanIpEntryA extremeVlanIpEntry contains layer 3
information about a particular IP VLAN
interface. ExtremeVlanIpEntry .1.3.6.1.4.1.1916.1.2.4.1.1 |
extremeVlanIpNetAddressThe IP network number for the IP VLAN interface defined
in the extremeVlanIfTable identified with the same index.rw IpAddress .1.3.6.1.4.1.1916.1.2.4.1.1.1 |
extremeVlanIpNetMaskThe IP network mask corresponding to the IP Network
address defined by extremeVlanIpIpNetAddress.rw IpAddress .1.3.6.1.4.1.1916.1.2.4.1.1.2 |
extremeVlanIpStatusThe status column for this IP VLAN entry.
This object can be set to:
active(1)
createAndGo(4)
destroy(6)
The following values may be read:
active(1)
Setting this object to active(1) or createAndGo(4) causes
the agent to attempt to create and commit the row based on
the contents of the objects in the row. If all necessary
information is present in the row and the values are
acceptible to the agent, the agent will change the
status to active(1). If any of the necessary objects
are not available, the agent will reject the row
creation request.
Setting this object to createAndWait(5) is not supported.
When the status changes to active(1), the agent applies the
IP parmeters to the IP VLAN interface identified by the
corresponding value of the extremeVlanIpIndex object.
Setting this object to destroy(6) will remove the IP
parmeters from the IP VLAN interface and remove the
entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.4.1.1.3 |
extremeVlanIpForwardingStateIndicates whether the IP Forwarding on this Vlan is
Enable or not. A true value indicates that the Vlan is
Enable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.4.1.1.4 |
extremeProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.5 |
extremeVlanProtocolTableTable of defined combinations of protocol IDs
that make up one protocol definition name.
All members of one protocol definition share
the same extremeVlanProtocolIndex. A given
protocol ID may appear in the definition of
just one protocol definition. This table will
typically contain some default entries for
popular protocols chosen by ExtremeWare. SEQUENCE OF ExtremeVlanProtocolEntry .1.3.6.1.4.1.1916.1.2.5.1 |
extremeVlanProtocolEntryOne member protocol ID of a protocol definition. ExtremeVlanProtocolEntry .1.3.6.1.4.1.1916.1.2.5.1.1 |
extremeVlanProtocolIndexAn index representing a protocol grouping of
protocol ID values. A limited number of
protocol groupings may be defined (up to 7
in ExtremeWare and 16 in EXOS). 0 is used
for internal purposes.rw INTEGER .1.3.6.1.4.1.1916.1.2.5.1.1.1 |
extremeVlanProtocolIdIndexAn index representing a particular protocol ID
within a protocol grouping. A limited number of
protocol IDs may be defined per
extremeVlanProtocolIndex (up to 6 in ExtremeWare).
0 is used for internal purposes.rw INTEGER .1.3.6.1.4.1.1916.1.2.5.1.1.2 |
extremeVlanProtocolNameA human-readable string representing this protocol.
This string should be the same for all entries
sharing a given extremeVlanProtocolIndex.
A ExtremeVlanProtocolEntry with
extremeVlanProtocolName of ANY represents a match
on all protocols: this entry may not be modified.rw DisplayString .1.3.6.1.4.1.1916.1.2.5.1.1.3 |
extremeVlanProtocolDllEncapsTypeRepresents the type of data-link encapsulation
in which the extremeVlanProtocolId protocol ID
is carried. The value any(1) is used to indicate
a wildcard and matches all encapsulations and
protocol IDs that are not explicitly mentioned
in this table. Entries of type any(1) may not
be created. The value none(5) is used to indicate
that no protocol IDs match this entry. A value
of none(5) may not be set by a manager.rw Enumeration .1.3.6.1.4.1.1916.1.2.5.1.1.4 |
extremeVlanProtocolIdThe protocol ID: for entries of type ethertype(2)
or llcSnapEthertype(4) this represents a 16-bit
protocol ID. For entries of type llc(3) it
represents a concatenation of LLC DSAP+SSAP in
network byte order. This value is not valid
for extremeVlanProtocolDllEncapsType values of
any(1) or none(5).rw INTEGER .1.3.6.1.4.1.1916.1.2.5.1.1.5 |
extremeVlanProtocolStatusThe row status variable, used according to
row installation and removal conventions.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.5.1.1.6 |
extremeVlanProtocolVlanTableTable to apply one of the protocol definitions
in extremeVlanProtocolTable to a given VLAN
This applies to all ports that are untagged
in this VLAN). A limited number of protocols
may be applied simultaneously in one device
(up to 8 in ExtremeWare). SEQUENCE OF ExtremeVlanProtocolVlanEntry .1.3.6.1.4.1.1916.1.2.5.2 |
extremeVlanProtocolVlanEntryA mapping of untagged packets of one protocol
onto a particular VLAN. ExtremeVlanProtocolVlanEntry .1.3.6.1.4.1.1916.1.2.5.2.1 |
extremeVlanProtocolVlanIfIndexThe index value of this row and the vlan's ifIndex in the
ifTable. The NMS obtains the index value for this row by
reading the extremeNextAvailableVirtIfIndex object.rw INTEGER (extremeware) SYNTAX Integer32 .1.3.6.1.4.1.1916.1.2.5.2.1.1 |
extremeVlanProtocolVlanProtocolIndexAn index representing a protocol grouping of
protocol ID values. A limited number of
protocol groupings may be defined (up to 7
in ExtremeWare).rw INTEGER (extremeware) SYNTAX Integer32 .1.3.6.1.4.1.1916.1.2.5.2.1.2 |
extremeVlanProtocolVlanStatusThe row status variable, used according to
row installation and removal conventions.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.5.2.1.3 |
extremeVlanProtocolDefTableTable of defined combinations of protocols and
DLLEncaps type. This table will
typically contain some default entries for
popular protocols chosen by ExtremeWare. SEQUENCE OF ExtremeVlanProtocolDefEntry .1.3.6.1.4.1.1916.1.2.5.3 |
extremeVlanProtocolDefEntryOne member representing combination of protocol and
DLLEncaps Type. ExtremeVlanProtocolDefEntry .1.3.6.1.4.1.1916.1.2.5.3.1 |
extremeVlanProtocolDefNameA human-readable string representing this protocol.
A ExtremeVlanProtocolEntry with
extremeVlanProtocol2Name of ANY represents a match
on all protocols: this entry may not be modified. DisplayString .1.3.6.1.4.1.1916.1.2.5.3.1.1 |
extremeVlanProtocolDefDllEncapsTypeRepresents the type of data-link encapsulation
in which the protocol designated by
extremeVlanProtocolDefName is carried.
The value any(1) is used to indicate
a wildcard and matches all encapsulations and
protocol IDs that are not explicitly mentioned
in this table. Entries of type any(1) may not
be created. The value none(5) is used to indicate
that no protocol IDs match this entry. A value
of none(5) may not be set by a manager. Enumeration .1.3.6.1.4.1.1916.1.2.5.3.1.2 |
extremeVlanProtocolDefValueThe protocol ID: for entries of type ethertype(2)
or llcSnapEthertype(4) this represents a 16-bit
protocol ID. For entries of type llc(3) it
represents a concatenation of LLC DSAP+SSAP in
network byte order. This value is not valid
for extremeVlanProtocolDefDllEncapsType values of
any(1) or none(5). INTEGER .1.3.6.1.4.1.1916.1.2.5.3.1.3 |
extremeVlanProtocolDefStatusThe row status variable, used according to
row installation and removal conventions.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.5.3.1.4 |
extremeVlanProtocolBindingTableTable to apply one of the protocol definitions
in extremeVlanProtocolDefTable to a given VLAN
This applies to all ports that are untagged
in this VLAN). A limited number of protocols
may be applied simultaneously in one device
(up to 8 in ExtremeWare). SEQUENCE OF ExtremeVlanProtocolBindingEntry .1.3.6.1.4.1.1916.1.2.5.4 |
extremeVlanProtocolBindingEntryA mapping of untagged packets of one protocol
onto a particular VLAN. ExtremeVlanProtocolBindingEntry .1.3.6.1.4.1.1916.1.2.5.4.1 |
extremeVlanProtocolBindingIfIndexThe index value of this row and the vlan's ifIndex in the
ifTable. The NMS obtains the index value for this row by
reading the extremeNextAvailableVirtIfIndex object. Integer32 .1.3.6.1.4.1.1916.1.2.5.4.1.1 |
extremeVlanProtocolBindingNameA human-readable string representing this protocol.
A ExtremeVlanProtocolBindingEntry with
extremeVlanProtocolBindingName of ANY represents a
match on all protocols: this entry may not be modified.rw DisplayString .1.3.6.1.4.1.1916.1.2.5.4.1.2 |
extremeVlanProtocolBindingStatusThe row status variable, used according to
row installation and removal conventions.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.5.4.1.3 |
extremeVlanOpaqueGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.6 |
extremeVlanOpaqueTableThis table lists the ports associated with each VLAN interface. SEQUENCE OF ExtremeVlanOpaqueEntry .1.3.6.1.4.1.1916.1.2.6.1 |
extremeVlanOpaqueEntryThis represents the tagged and untagged ports on each slot per vlan. ExtremeVlanOpaqueEntry .1.3.6.1.4.1.1916.1.2.6.1.1 |
extremeVlanOpaqueTaggedPortsEach bit in the octet string represents one port.
A 1 means that the port is a tagged port in that vlan.
The bit value for a port is 0 otherwise.ro PortList (EXTREME-BASE-MIB) .1.3.6.1.4.1.1916.1.2.6.1.1.1 |
extremeVlanOpaqueUntaggedPortsEach bit in the octet string represents one port.
A 1 means that the port is an untagged port in that vlan.
The bit value for a port is 0 otherwise.ro PortList (EXTREME-BASE-MIB) .1.3.6.1.4.1.1916.1.2.6.1.1.2 |
extremeVlanOpaqueControlTableThis table is used to configure the ports associated with each VLAN
interface. The table is used to add/delete ports on a vlan. The table is
transitional in nature and SNMP read operations must not be performed on it.
Use extremeVlanOpaqueTable for reading the port membership association with vlans SEQUENCE OF ExtremeVlanOpaqueControlEntry .1.3.6.1.4.1.1916.1.2.6.2 |
extremeVlanOpaqueControlEntryThis represents a control table entry (command) to configure the tagged
and untagged ports on each slot per vlan. The first index of the entry is
the ifIndex of the VLAN and second index is the slot number of the ports.
When adding untagged ports to a VLAN, those ports maybe not be untagged ports
for another VLAN (assuming both VLANs use the ANY protocol filter). Such
ports must first be deleted from the other VLAN(s) or an error will occur.
The operation will succeed or fail in its entirety, no partial results on some of the ports. ExtremeVlanOpaqueControlEntry .1.3.6.1.4.1.1916.1.2.6.2.1 |
extremeVlanOpaqueControlPortsThe octet string representing a list of ports in
bitwise form.rw PortList (EXTREME-BASE-MIB) .1.3.6.1.4.1.1916.1.2.6.2.1.1 |
extremeVlanOpaqueControlOperationThe operation code for this entry.
addTagged(1) = Ports referred to in the extremeVlanOpaqueControlPorts
variable are added as tagged ports to the VLAN indicated
by the index. The ports belong to the slot number as
indicated by the second index of the variable.
addUntagged(2) = Ports referred to in the extremeVlanOpaqueControlPorts
variable are added as tagged ports to the VLAN indicated
by the index. The ports belong to the slot number as
indicated by the second index of the variable.
delete(3) = Ports referred to in the extremeVlanOpaqueControlPorts
variable are removed from the VLAN indicated by the index.
The ports belong to the slot number as indicated by the
second index of the variable.rw Enumeration .1.3.6.1.4.1.1916.1.2.6.2.1.2 |
extremeVlanOpaqueControlStatusThe status of this entry as per standard RowStatus
conventions. Note however, that only the CreateAndGo
state is supported.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.6.2.1.3 |
extremeVlanStackGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.7 |
extremeVlanStackTableRepresents those components of the ifStackTable that do not
contain a Physical interface. SEQUENCE OF ExtremeVlanStackEntry .1.3.6.1.4.1.1916.1.2.7.1 |
extremeVlanStackEntryEach entry in this read-only table defines which interfaces are
on top of which one. All information in the table is also
contained in ifStackTable. The Physical interfaces in the
ifStackTable are not represented here. ExtremeVlanStackEntry .1.3.6.1.4.1.1916.1.2.7.1.1 |
extremeVlanStackHigherLayerThe higher layer in the logical vlan hierarchy.ro Integer32 .1.3.6.1.4.1.1916.1.2.7.1.1.1 |
extremeVlanStackLowerLayerThe lower layer in the logical vlan hierarchy.ro Integer32 .1.3.6.1.4.1.1916.1.2.7.1.1.2 |
extremeVlanStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.8 |
extremeVlanL2StatsTableThis tables contains per-VLAN layer 2 statistics information. SEQUENCE OF ExtremeVlanL2StatsEntry .1.3.6.1.4.1.1916.1.2.8.1 |
extremeVlanL2StatsEntry ExtremeVlanL2StatsEntry .1.3.6.1.4.1.1916.1.2.8.1.1 |
extremeVlanL2StatsIfDescrThis is a description(name) of the VLAN.ro DisplayString .1.3.6.1.4.1.1916.1.2.8.1.1.1 |
extremeVlanL2StatsPktsToCpuThe total number of packets of this VLAN sent to the CPU.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.1.1.2 |
extremeVlanL2StatsPktsLearntThe total number of packets learnt on this VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.1.1.3 |
extremeVlanL2StatsIgmpCtrlPktsSnoopedThe total number of IGMP control packets snooped on this VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.1.1.4 |
extremeVlanL2StatsIgmpDataPktsSwitchedThe total number of IGMP data packets switched on this VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.1.1.5 |
extremePortVlanStatsTableVlan statistics per port. SEQUENCE OF ExtremePortVlanStatsEntry .1.3.6.1.4.1.1916.1.2.8.2 |
extremePortVlanStatsEntryVlan port statistics Entry. ExtremePortVlanStatsEntry .1.3.6.1.4.1.1916.1.2.8.2.1 |
extremeStatsPortIfIndexThe index of this table.ro Integer32 .1.3.6.1.4.1.1916.1.2.8.2.1.1 |
extremeStatsVlanNameIndexThe index of this table.ro DisplayString .1.3.6.1.4.1.1916.1.2.8.2.1.2 |
extremePortVlanStatsCntrTypeThe flag to decide what fields to display, basic
or extended. Currently, it is read-only and will
reflect whatever has been set for the switch
through the cli.ro Integer32 .1.3.6.1.4.1.1916.1.2.8.2.1.3 |
extremePortVlanUnicastReceivedPacketsCounterThe number of Unicast packets received by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.4 |
extremePortVlanMulticastReceivedPacketsCounterThe number of Multicast packets received by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.5 |
extremePortVlanBroadcastReceivedPacketsCounterThe number of Broadcast packets received by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.6 |
extremePortVlanTotalReceivedBytesCounterThe total number of bytes received by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.7 |
extremePortVlanTotalReceivedFramesCounterThe total number of frames received by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.8 |
extremePortVlanUnicastTransmittedPacketsCounterThe number of Unicast packets transmitted by a
port for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.9 |
extremePortVlanMulticastTransmittedPacketsCounterThe number of Multicast packets transmitted by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.10 |
extremePortVlanBroadcastTransmittedPacketsCounterThe number of Broadcast packets transmitted by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.11 |
extremePortVlanTotalTransmittedBytesCounterThe total number of bytes transmitted by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.12 |
extremePortVlanTotalTransmittedFramesCounterThe total number of frames transmitted by a port
for a particular VLAN.ro Counter64 .1.3.6.1.4.1.1916.1.2.8.2.1.13 |
extremePortConfigureVlanStatusThe row status variable, used according to
row installation and removal conventions.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.8.2.1.14 |
extremeVlanAggregationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.9 |
extremeVlanAggregationTableThis table contains the VLAN aggregation information. SEQUENCE OF ExtremeVlanAggregationEntry .1.3.6.1.4.1.1916.1.2.9.1 |
extremeVlanAggregationEntryInformation about the individual VLAN aggregation entry. ExtremeVlanAggregationEntry .1.3.6.1.4.1.1916.1.2.9.1.1 |
extremeVlanAggregationSuperVlanIfIndexThe Super Vlan index for this entry.ro Integer32 .1.3.6.1.4.1.1916.1.2.9.1.1.1 |
extremeVlanAggregationSubVlanIfIndexThe Sub Vlan index for this entry.ro Integer32 .1.3.6.1.4.1.1916.1.2.9.1.1.2 |
extremeVlanAggregationSubVlanStartIpNetAddressThis represents the start network address of the IP range.rw IpAddress .1.3.6.1.4.1.1916.1.2.9.1.1.3 |
extremeVlanAggregationSubVlanStartIpNetMaskThis represents the start network address mask of the IP rangero IpAddress .1.3.6.1.4.1.1916.1.2.9.1.1.4 |
extremeVlanAggregationSubVlanEndIpNetAddressThis represents the end network address of the IP range.rw IpAddress .1.3.6.1.4.1.1916.1.2.9.1.1.5 |
extremeVlanAggregationSubVlanEndIpNetMaskThis represents the end network address mask of the IP range.ro IpAddress .1.3.6.1.4.1.1916.1.2.9.1.1.6 |
extremeVlanAggregationStatusThe status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.9.1.1.7 |
extremeVlanAggregationConfigTableThis table contains the sub VLAN proxy setting information. SEQUENCE OF ExtremeVlanAggregationConfigEntry .1.3.6.1.4.1.1916.1.2.9.2 |
extremeVlanAggregationConfigEntryInformation about the individual VLAN aggregation entry. ExtremeVlanAggregationConfigEntry .1.3.6.1.4.1.1916.1.2.9.2.1 |
extremeVlanAggregationConfigSuperVlanIfIndexThe Super Vlan index for this entry.ro Integer32 .1.3.6.1.4.1.1916.1.2.9.2.1.1 |
extremeVlanAggregationConfigSubVlanProxyEnableThe boolean flag that prevents normal communication between sub vlans.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.9.2.1.2 |
extremeVlanTranslationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.2.10 |
extremeVlanTranslationTableThis table contains the VLAN translation information. SEQUENCE OF ExtremeVlanTranslationEntry .1.3.6.1.4.1.1916.1.2.10.1 |
extremeVlanTranslationEntryInformation about the individual VLAN translation entry. ExtremeVlanTranslationEntry .1.3.6.1.4.1.1916.1.2.10.1.1 |
extremeVlanTranslationSuperVlanIfIndexThe Super Vlan index for this entry.ro Integer32 .1.3.6.1.4.1.1916.1.2.10.1.1.1 |
extremeVlanTranslationMemberVlanIfIndexThe member Vlan index for this entry.ro Integer32 .1.3.6.1.4.1.1916.1.2.10.1.1.2 |
extremeVlanTranslationStatusThe status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1916.1.2.10.1.1.3 |