EXTREME-POS-MIB
Extreme POS objects: objects common to POS MIBs
Main OID:
extremePOSMib.1.3.6.1.4.1.1916.1.20
75
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
75 total| Object Name |
|---|
extremePOSMibExtreme POS objects: objects common to POS MIBs MODULE-IDENTITY .1.3.6.1.4.1.1916.1.20 |
SNMPv2-SMIExtreme POS objects: objects common to POS MIBs Unknown .1.3.6.1.4.1.1916.1.20 |
extremeAps OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.20.1 |
extremeApsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.20.1.1 |
extremeApsConfigEnabledGlobal APS enablementro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.1.1 |
extremeApsGroupConfigTableThis table contains configuration information
by defined APS group. SEQUENCE OF ExtremeApsGroupConfigEntry .1.3.6.1.4.1.1916.1.20.1.1.2 |
extremeApsGroupConfigEntry ExtremeApsGroupConfigEntry .1.3.6.1.4.1.1916.1.20.1.1.2.1 |
extremeApsGroupConfigGroupNumberThe group number which uniquely identifies
the APS group.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.2.1.1 |
extremeApsGroupConfigRevertModeThe revertive mode configured for the APS
group. This indicates whether APS will
switch-back automatically after the working
line error is cleared. In non-revertive
mode, manual intervention is required for
switch-back.ro Enumeration .1.3.6.1.4.1.1916.1.20.1.1.2.1.2 |
extremeApsGroupConfigRevertMinutesThe number of minutes APS will wait after
the error has been cleared before switching
back to the working line. During this
interval, the K1 request will indicate
WTR (wait-to-restore). This field is only
valid in revertive mode.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.2.1.3 |
extremeApsGroupConfigDirectionThe directional mode configured for the
APS group. This indicates whether protection
switches are coordinated between both POS
equipment and ADM (bidirectional) or not
(unidirectional).ro Enumeration .1.3.6.1.4.1.1916.1.20.1.1.2.1.4 |
extremeApsGroupConfigTimerIntervalThe number of seconds between APS out-of-band
peer protocol hello messages. This value is
relevant when the working line and protection
line exist is physically different chassis.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.2.1.5 |
extremeApsGroupConfigTimerMissesThe number of APS out-of-band peer protocol
messages transmitted without receiving a
response before the protection switch declares
the working switch inoperable. When this occurs
the protection switch initiates a line switch
over via APS.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.2.1.6 |
extremeApsGroupConfigAuthenticateWhen enabled, the authentication string on both
working and protection switches must match.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.1.2.1.7 |
extremeApsGroupConfigAuthStringIf configured, this is the authentication string
that must match between working and protection
switches. This field is relevant if the APS group
is configured to authenticate.ro DisplayString .1.3.6.1.4.1.1916.1.20.1.1.2.1.8 |
extremeApsPortConfigTableThis table contains configuration information
for APS ports. SEQUENCE OF ExtremeApsPortConfigEntry .1.3.6.1.4.1.1916.1.20.1.1.3 |
extremeApsPortConfigEntry ExtremeApsPortConfigEntry .1.3.6.1.4.1.1916.1.20.1.1.3.1 |
extremeApsPortConfigGroupNumberThe group number which uniquely identifies
the APS group.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.3.1.1 |
extremeApsPortConfigPortNumberThe value of ifIndex that identifies the port.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.3.1.2 |
extremeApsPortConfigPortTypeThe port type designation.ro Enumeration .1.3.6.1.4.1.1916.1.20.1.1.3.1.3 |
extremeApsProtectPortConfigTableThis table contains configuration information
for APS protection ports. SEQUENCE OF ExtremeApsProtectPortConfigEntry .1.3.6.1.4.1.1916.1.20.1.1.4 |
extremeApsProtectPortConfigEntry ExtremeApsProtectPortConfigEntry .1.3.6.1.4.1.1916.1.20.1.1.4.1 |
extremeApsProtectPortConfigGroupNumberThe group number which uniquely identifies
the APS group.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.4.1.1 |
extremeApsProtectPortConfigPortNumberThe value of ifIndex that identifies
the protection port.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.1.4.1.2 |
extremeApsProtectPortConfigWorkingIpAddrThe IP address of the working switch. If the
working and protection lines reside on the same
chassis, this IP address will be a local address.ro IpAddress .1.3.6.1.4.1.1916.1.20.1.1.4.1.3 |
extremeApsStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.20.1.2 |
extremeApsGroupTableThis table contains run-time information
by defined APS group. SEQUENCE OF ExtremeApsGroupEntry .1.3.6.1.4.1.1916.1.20.1.2.1 |
extremeApsGroupEntry ExtremeApsGroupEntry .1.3.6.1.4.1.1916.1.20.1.2.1.1 |
extremeApsGroupGroupNumberThe group number which uniquely identifies
the APS group.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.1.1.1 |
extremeApsGroupActivePortThe APS port which is currently carrying the
network traffic.ro Enumeration .1.3.6.1.4.1.1916.1.20.1.2.1.1.2 |
extremeApsGroupEffectiveDirectionThe effective directional mode for the APS
group. When this value differs from the
configured directional mode, check the
ADM and switch provisioning for a mis-
configuration.ro Enumeration .1.3.6.1.4.1.1916.1.20.1.2.1.1.3 |
extremeApsGroupPeerProtoStatusThe APS out-of-band peer protocol status
for a group.ro Enumeration .1.3.6.1.4.1.1916.1.20.1.2.1.1.4 |
extremeApsProtectPortTableThis table contains run-time information
by defined APS protection port. SEQUENCE OF ExtremeApsProtectPortEntry .1.3.6.1.4.1.1916.1.20.1.2.2 |
extremeApsProtectPortEntry ExtremeApsProtectPortEntry .1.3.6.1.4.1.1916.1.20.1.2.2.1 |
extremeApsProtectPortGroupNumberThe group number which uniquely identifies
the APS group.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.1 |
extremeApsProtectPortPortNumberThe value of ifIndex that identifies
the protection port.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.2 |
extremeApsProtectPortTransmitK1The K1 overhead byte currently being transmitted
on the indicated protection port.ro OCTET STRING .1.3.6.1.4.1.1916.1.20.1.2.2.1.3 |
extremeApsProtectPortTransmitK2The K2 overhead byte currently being transmitted
on the indicated protection port.ro OCTET STRING .1.3.6.1.4.1.1916.1.20.1.2.2.1.4 |
extremeApsProtectPortReceiveK1The K1 overhead byte currently being received
on the indicated protection port.ro OCTET STRING .1.3.6.1.4.1.1916.1.20.1.2.2.1.5 |
extremeApsProtectPortReceiveK2The K2 overhead byte currently being received
on the indicated protection port.ro OCTET STRING .1.3.6.1.4.1.1916.1.20.1.2.2.1.6 |
extremeApsProtectPortSwitchInitByWorkingThe number of switches that have been
initiated by the working-line router.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.7 |
extremeApsProtectPortSwitchInitByProtectThe number of switches that have been
initiated by the protection-line router.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.8 |
extremeApsProtectPortSwitchInitByADMThe number of switches that have been
initiated by the ADM.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.9 |
extremeApsProtectPortSwitchInitByCmdThe number of switches that have been
initiated by an external CLI command.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.10 |
extremeApsProtectPortSuccessfulSwitchesThe number of successful APS line switches.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.11 |
extremeApsProtectPortHelloProtFailsThe number of APS out-of-band peer protocol
failures recorded. This situation causes
the protection-line router to initiate a
line switch.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.2.2.1.12 |
extremeApsErrors OBJECT IDENTIFIER .1.3.6.1.4.1.1916.1.20.1.3 |
extremeApsLineErrorTableThis table contains APS line error
information. SEQUENCE OF ExtremeApsLineErrorEntry .1.3.6.1.4.1.1916.1.20.1.3.1 |
extremeApsLineErrorEntry ExtremeApsLineErrorEntry .1.3.6.1.4.1.1916.1.20.1.3.1.1 |
extremeApsLineErrorGroupNumberThe group number which uniquely identifies the
APS group.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.1.1.1 |
extremeApsLineErrorPortNumberThe ifIndex value which identifies the APS port.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.1.1.2 |
extremeApsLineErrorSignalDegradeActiveIndicates whether a signal degrade condition
currently exists on the line.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.1.1.3 |
extremeApsLineErrorBERSignalDegradeActiveIndicates whether a signal degrade condition
due to excessive Bit-Error-Rate currently exists
on the line.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.1.1.4 |
extremeApsLineErrorSignalFailActiveIndicates whether a signal fail condition
currently exists on the line.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.1.1.5 |
extremeApsLineErrorBERSignalFailActiveIndicates whether a signal fail condition
due to excessive Bit-Error-Rate currently
exists on the line.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.1.1.6 |
extremeApsLineErrorSignalDegradesThe number of signal degrades that have
been recorded on the line.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.1.1.7 |
extremeApsLineErrorBERSignalDegradesThe number of signal degrades due to excessive
Bit-Error-Rate that have been recorded on the
line.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.1.1.8 |
extremeApsLineErrorSignalFailsThe number of signal fails that have
been recorded on the line.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.1.1.9 |
extremeApsLineErrorBERSignalFailsThe number of signal fails due to excessive
Bit-Error-Rate that have been recorded on the
line.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.1.1.10 |
extremeApsProtocolErrorTableThis table contains APS protocol error
information. These errors are relevant
for APS protection ports. SEQUENCE OF ExtremeApsProtocolErrorEntry .1.3.6.1.4.1.1916.1.20.1.3.2 |
extremeApsProtocolErrorEntry ExtremeApsProtocolErrorEntry .1.3.6.1.4.1.1916.1.20.1.3.2.1 |
extremeApsProtocolErrorGroupNumberThe group number which uniquely identifies the
APS group.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.2.1.1 |
extremeApsProtocolErrorPortNumberThe ifIndex value which identifies the APS
protection port.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.2.1.2 |
extremeApsProtocolErrorModeMismatchDefectIndicates whether a Mode Mismatch defect currently
exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.3 |
extremeApsProtocolErrorProtSwitchByteDefectIndicates whether a Protection Switching Byte defect
currently exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.4 |
extremeApsProtocolErrorChannelMismatchDefectIndicates whether a Channel Mismatch defect currently
exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.5 |
extremeApsProtocolErrorFarEndProtectDefectIndicates whether a Far-End Protection defect currently
exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.6 |
extremeApsProtocolErrorModeMismatchFailureIndicates whether a Mode Mismatch failure currently
exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.7 |
extremeApsProtocolErrorProtSwitchByteFailureIndicates whether a Protection Switching Byte failure
currently exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.8 |
extremeApsProtocolErrorChannelMismatchFailureIndicates whether a Channel Mismatch failure currently
exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.9 |
extremeApsProtocolErrorFarEndProtectFailureIndicates whether a Far-End Protection failure currently
exists on the port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1916.1.20.1.3.2.1.10 |
extremeApsProtocolErrorModeMismatchNumFailsThe number of Mode Mismatch failures that have
been recorded.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.2.1.11 |
extremeApsProtocolErrorProtSwitchByteNumFailsThe number of Protection Switching Byte failures
that have been recorded.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.2.1.12 |
extremeApsProtocolErrorChannelMismatchNumFailsThe number of Channel Mismatch failures that have
been recorded.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.2.1.13 |
extremeApsProtocolErrorFarEndProtectNumFailsThe number of Far-End Protection failures that have
been recorded.ro INTEGER .1.3.6.1.4.1.1916.1.20.1.3.2.1.14 |
More MIBs from Extreme Networks
Browse all Extreme NetworksMIBs →EXTREME-WIRELESS-MIB
SNMP MIB module
836 objects→
EXTREME-BASE-MIB
The EXTREME-BASE-MIB module provides SNMP management interfaces for Extreme Networks wireless access points and controllers, specifically exposing tables for monitoring wireless client associations, access point operational states, and RF interface statistics.
243 objects→
EXTREME-SYSTEM-MIB
SNMP MIB module
182 objects→
EXTREME-ESRP-MIB
SNMP MIB module
127 objects→
EXTREME-PORT-MIB
SNMP MIB module
123 objects→
EXTREME-VLAN-MIB
The EXTREME-VLAN-MIB provides SNMP access to configure and monitor Virtual LAN (VLAN) parameters, including port assignments, VLAN membership states, and bridging statistics on Extreme Networks switching hardware. This module enables the tracking of VLAN operational status, MAC address table entries, and traffic counters essential for Layer 2 network segmentation and troubleshooting.
120 objects→