ETHERLIKE-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
57
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
57 total| Object Name |
|---|
dot3 OBJECT IDENTIFIER .1.3.6.1.2.1.10.7 |
dot3StatsTableStatistics for a collection of ethernet-like
interfaces attached to a particular system.
There will be one row in this table for each
ethernet-like interface in the system. SEQUENCE OF Dot3StatsEntry .1.3.6.1.2.1.10.7.2 |
dot3StatsEntryStatistics for a particular interface to an
ethernet-like medium. Dot3StatsEntry .1.3.6.1.2.1.10.7.2.1 |
dot3StatsIndexAn index value that uniquely identifies an
interface to an ethernet-like medium. The
interface identified by a particular value of
this index is the same interface as identified
by the same value of ifIndex.ro InterfaceIndex -- Rsyntax INTEGER .1.3.6.1.2.1.10.7.2.1.1 |
dot3StatsAlignmentErrorsA count of frames received on a particular
interface that are not an integral number of
octets in length and do not pass the FCS check.
The count represented by an instance of this
object is incremented when the alignmentError
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC.
This counter does not increment for 8-bit wide
group encoding schemes.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.2 |
dot3StatsFCSErrorsA count of frames received on a particular
interface that are an integral number of octets
in length but do not pass the FCS check. This
count does not include frames received with
frame-too-long or frame-too-short error.
The count represented by an instance of this
object is incremented when the frameCheckError
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC.
Note: Coding errors detected by the physical
layer for speeds above 10 Mb/s will cause the
frame to fail the FCS check.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.3 |
dot3StatsSingleCollisionFramesA count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by exactly one collision.
A frame that is counted by an instance of this
object is also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or ifOutBroadcastPkts,
and is not counted by the corresponding
instance of the dot3StatsMultipleCollisionFrames
object.
This counter does not increment when the
interface is operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.4 |
dot3StatsMultipleCollisionFramesA count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by more than one collision.
A frame that is counted by an instance of this
object is also counted by the corresponding
instance of either the ifOutUcastPkts,
ifOutMulticastPkts, or ifOutBroadcastPkts,
and is not counted by the corresponding
instance of the dot3StatsSingleCollisionFrames
object.
This counter does not increment when the
interface is operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.5 |
dot3StatsSQETestErrorsA count of times that the SQE TEST ERROR
message is generated by the PLS sublayer for a
particular interface. The SQE TEST ERROR
is set in accordance with the rules for
verification of the SQE detection mechanism in
the PLS Carrier Sense Function as described in
IEEE Std. 802.3, 1998 Edition, section 7.2.4.6.
This counter does not increment on interfaces
operating at speeds greater than 10 Mb/s, or on
interfaces operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.6 |
dot3StatsDeferredTransmissionsA count of frames for which the first
transmission attempt on a particular interface
is delayed because the medium is busy.
The count represented by an instance of this
object does not include frames involved in
collisions.
This counter does not increment when the
interface is operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.7 |
dot3StatsLateCollisionsThe number of times that a collision is
detected on a particular interface later than
one slotTime into the transmission of a packet.
A (late) collision included in a count
represented by an instance of this object is
also considered as a (generic) collision for
purposes of other collision-related
statistics.
This counter does not increment when the
interface is operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.8 |
dot3StatsExcessiveCollisionsA count of frames for which transmission on a
particular interface fails due to excessive
collisions.
This counter does not increment when the
interface is operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.9 |
dot3StatsInternalMacTransmitErrorsA count of frames for which transmission on a
particular interface fails due to an internal
MAC sublayer transmit error. A frame is only
counted by an instance of this object if it is
not counted by the corresponding instance of
either the dot3StatsLateCollisions object, the
dot3StatsExcessiveCollisions object, or the
dot3StatsCarrierSenseErrors object.
The precise meaning of the count represented by
an instance of this object is implementation-
specific. In particular, an instance of this
object may represent a count of transmission
errors on a particular interface that are not
otherwise counted.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.10 |
dot3StatsCarrierSenseErrorsThe number of times that the carrier sense
condition was lost or never asserted when
attempting to transmit a frame on a particular
interface.
The count represented by an instance of this
object is incremented at most once per
transmission attempt, even if the carrier sense
condition fluctuates during a transmission
attempt.
This counter does not increment when the
interface is operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.11 |
dot3StatsFrameTooLongsA count of frames received on a particular
interface that exceed the maximum permitted
frame size.
The count represented by an instance of this
object is incremented when the frameTooLong
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.13 |
dot3StatsInternalMacReceiveErrorsA count of frames for which reception on a
particular interface fails due to an internal
MAC sublayer receive error. A frame is only
counted by an instance of this object if it is
not counted by the corresponding instance of
either the dot3StatsFrameTooLongs object, the
dot3StatsAlignmentErrors object, or the
dot3StatsFCSErrors object.
The precise meaning of the count represented by
an instance of this object is implementation-
specific. In particular, an instance of this
object may represent a count of receive errors
on a particular interface that are not
otherwise counted.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.16 |
dot3StatsEtherChipSet******** THIS OBJECT IS DEPRECATED ********
This object contains an OBJECT IDENTIFIER
which identifies the chipset used to
realize the interface. Ethernet-like
interfaces are typically built out of
several different chips. The MIB implementor
is presented with a decision of which chip
to identify via this object. The implementor
should identify the chip which is usually
called the Medium Access Control chip.
If no such chip is easily identifiable,
the implementor should identify the chip
which actually gathers the transmit
and receive statistics and error
indications. This would allow a
manager station to correlate the
statistics and the chip generating
them, giving it the ability to take
into account any known anomalies
in the chip.rodeprecated OBJECT IDENTIFIER .1.3.6.1.2.1.10.7.2.1.17 |
dot3StatsSymbolErrorsFor an interface operating at 100 Mb/s, the
number of times there was an invalid data symbol
when a valid carrier was present.
For an interface operating in half-duplex mode
at 1000 Mb/s, the number of times the receiving
media is non-idle (a carrier event) for a period
of time equal to or greater than slotTime, and
during which there was at least one occurrence
of an event that causes the PHY to indicate
'Data reception error' or 'carrier extend error'
on the GMII.
For an interface operating in full-duplex mode
at 1000 Mb/s, the number of times the receiving
media is non-idle a carrier event) for a period
of time equal to or greater than minFrameSize,
and during which there was at least one
occurrence of an event that causes the PHY to
indicate 'Data reception error' on the GMII.
The count represented by an instance of this
object is incremented at most once per carrier
event, even if multiple symbol errors occur
during the carrier event. This count does
not increment if a collision is present.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.2.1.18 |
dot3StatsDuplexStatusThe current mode of operation of the MAC
entity. 'unknown' indicates that the current
duplex mode could not be determined.
Management control of the duplex mode is
accomplished through the MAU MIB. When
an interface does not support autonegotiation,
or when autonegotiation is not enabled, the
duplex mode is controlled using
ifMauDefaultType. When autonegotiation is
supported and enabled, duplex mode is controlled
using ifMauAutoNegAdvertisedBits. In either
case, the currently operating duplex mode is
reflected both in this object and in ifMauType.
Note that this object provides redundant
information with ifMauType. Normally, redundant
objects are discouraged. However, in this
instance, it allows a management application to
determine the duplex status of an interface
without having to know every possible value of
ifMauType. This was felt to be sufficiently
valuable to justify the redundancy.ro Enumeration .1.3.6.1.2.1.10.7.2.1.19 |
dot3CollTableA collection of collision histograms for a
particular set of interfaces. SEQUENCE OF Dot3CollEntry .1.3.6.1.2.1.10.7.5 |
dot3CollEntryA cell in the histogram of per-frame
collisions for a particular interface. An
instance of this object represents the
frequency of individual MAC frames for which
the transmission (successful or otherwise) on a
particular interface is accompanied by a
particular number of media collisions. Dot3CollEntry .1.3.6.1.2.1.10.7.5.1 |
dot3CollCountThe number of per-frame media collisions for
which a particular collision histogram cell
represents the frequency on a particular
interface. INTEGER .1.3.6.1.2.1.10.7.5.1.2 |
dot3CollFrequenciesA count of individual MAC frames for which the
transmission (successful or otherwise) on a
particular interface occurs after the
frame has experienced exactly the number
of collisions in the associated
dot3CollCount object.
For example, a frame which is transmitted
on interface 77 after experiencing
exactly 4 collisions would be indicated
by incrementing only dot3CollFrequencies.77.4.
No other instance of dot3CollFrequencies would
be incremented in this example.
This counter does not increment when the
interface is operating in full-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.5.1.3 |
dot3Tests OBJECT IDENTIFIER .1.3.6.1.2.1.10.7.6 |
dot3TestTdr OBJECT IDENTIFIER .1.3.6.1.2.1.10.7.6.1 |
dot3TestLoopBack OBJECT IDENTIFIER .1.3.6.1.2.1.10.7.6.2 |
dot3Errors OBJECT IDENTIFIER .1.3.6.1.2.1.10.7.7 |
dot3ErrorInitError OBJECT IDENTIFIER .1.3.6.1.2.1.10.7.7.1 |
dot3ErrorLoopbackError OBJECT IDENTIFIER .1.3.6.1.2.1.10.7.7.2 |
dot3ControlTableA table of descriptive and status information
about the MAC Control sublayer on the
ethernet-like interfaces attached to a
particular system. There will be one row in
this table for each ethernet-like interface in
the system which implements the MAC Control
sublayer. If some, but not all, of the
ethernet-like interfaces in the system implement
the MAC Control sublayer, there will be fewer
rows in this table than in the dot3StatsTable. SEQUENCE OF Dot3ControlEntry .1.3.6.1.2.1.10.7.9 |
dot3ControlEntryAn entry in the table, containing information
about the MAC Control sublayer on a single
ethernet-like interface. Dot3ControlEntry .1.3.6.1.2.1.10.7.9.1 |
dot3ControlFunctionsSupportedA list of the possible MAC Control functions
implemented for this interface.ro OCTET STRING .1.3.6.1.2.1.10.7.9.1.1 |
dot3ControlInUnknownOpcodesA count of MAC Control frames received on this
interface that contain an opcode that is not
supported by this device.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.9.1.2 |
dot3PauseTableA table of descriptive and status information
about the MAC Control PAUSE function on the
ethernet-like interfaces attached to a
particular system. There will be one row in
this table for each ethernet-like interface in
the system which supports the MAC Control PAUSE
function (i.e., the 'pause' bit in the
corresponding instance of
dot3ControlFunctionsSupported is set). If some,
but not all, of the ethernet-like interfaces in
the system implement the MAC Control PAUSE
function (for example, if some interfaces only
support half-duplex), there will be fewer rows
in this table than in the dot3StatsTable. SEQUENCE OF Dot3PauseEntry .1.3.6.1.2.1.10.7.10 |
dot3PauseEntryAn entry in the table, containing information
about the MAC Control PAUSE function on a single
ethernet-like interface. Dot3PauseEntry .1.3.6.1.2.1.10.7.10.1 |
dot3PauseAdminModeThis object is used to configure the default
administrative PAUSE mode for this interface.
This object represents the
administratively-configured PAUSE mode for this
interface. If auto-negotiation is not enabled
or is not implemented for the active MAU
attached to this interface, the value of this
object determines the operational PAUSE mode
of the interface whenever it is operating in
full-duplex mode. In this case, a set to this
object will force the interface into the
specified mode.
If auto-negotiation is implemented and enabled
for the MAU attached to this interface, the
PAUSE mode for this interface is determined by
auto-negotiation, and the value of this object
denotes the mode to which the interface will
automatically revert if/when auto-negotiation is
later disabled. Note that when auto-negotiation
is running, administrative control of the PAUSE
mode may be accomplished using the
ifMauAutoNegCapAdvertisedBits object in the
MAU-MIB.
Note that the value of this object is ignored
when the interface is not operating in
full-duplex mode.
An attempt to set this object to
'enabledXmit(2)' or 'enabledRcv(3)' will fail
on interfaces that do not support operation
at greater than 100 Mb/s.rw Enumeration .1.3.6.1.2.1.10.7.10.1.1 |
dot3PauseOperModeThis object reflects the PAUSE mode currently
in use on this interface, as determined by
either (1) the result of the auto-negotiation
function or (2) if auto-negotiation is not
enabled or is not implemented for the active MAU
attached to this interface, by the value of
dot3PauseAdminMode. Interfaces operating at
100 Mb/s or less will never return
'enabledXmit(2)' or 'enabledRcv(3)'. Interfaces
operating in half-duplex mode will always return
'disabled(1)'. Interfaces on which
auto-negotiation is enabled but not yet
completed should return the value
'disabled(1)'.ro Enumeration .1.3.6.1.2.1.10.7.10.1.2 |
dot3InPauseFramesA count of MAC Control frames received on this
interface with an opcode indicating the PAUSE
operation.
This counter does not increment when the
interface is operating in half-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.10.1.3 |
dot3OutPauseFramesA count of MAC Control frames transmitted on
this interface with an opcode indicating the
PAUSE operation.
This counter does not increment when the
interface is operating in half-duplex mode.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.2.1.10.7.10.1.4 |
etherMIB OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35 |
RFC1155-SMI Unknown .1.3.6.1.4.1.3727.20.20.3.1.35 |
etherMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.1 |
etherConformance OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2 |
etherGroups OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1 |
etherStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.1 |
etherCollisionTableGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.2 |
etherStats100MbsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.3 |
etherStatsBaseGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.4 |
etherStatsLowSpeedGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.5 |
etherStatsHighSpeedGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.6 |
etherDuplexGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.7 |
etherControlGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.8 |
etherControlPauseGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.1.9 |
etherCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.2 |
etherCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.2.1 |
ether100MbsCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.2.2 |
dot3Compliance OBJECT IDENTIFIER .1.3.6.1.4.1.3727.20.20.3.1.35.2.2.3 |