Dell-VRTX-BRGMACSWITCH-MIB
The Dell-VRTX-BRGMACSWITCH-MIB module enables monitoring and management of MAC address table entries, forwarding states, and switching parameters for the Dell VRTX Blade Server's integrated Broadcom-based internal network switch. It provides specific OID access to track port-level switching metrics, including learned MAC addresses, VLAN associations, and interface status for the VRTX chassis's internal fabric.
Imported Objects
Objects
12 total| Object Name |
|---|
rlBrgMacSwitchThis private MIB module defines Switching Parameters private MIBs. MODULE-IDENTITY .1.3.6.1.4.1.89.50 |
rlBrgMacSwVersionMIB's version, the current version is 2.ro INTEGER .1.3.6.1.4.1.89.50.1 |
rlBrgMacSwMaxTableNumberMaximum number of MAC Tables supported by the device.ro INTEGER .1.3.6.1.4.1.89.50.2 |
rlBrgMacSwDynamicTablesSpecifies whether the device supports port dynamic MAC tables.ro Enumeration .1.3.6.1.4.1.89.50.3 |
rlBrgMacSwOldEntryDeleteModeThe method used to delete old unused entries refresh_flag: The high level sets a flag when it adds or updates an entry, the Switch clears the flag each time, when it learns the station once more. aging_flag: The high level clears a flag when it adds or updates an entry, the Switch sets the flag each time, when it learns the station once more. aging_time: The high level defines a timeout, the Switch sends a message to the high level each time when the station doesn't send messages during interval between timeout and 2*timeout. Boundaries: The Switch doesn't support any mechanism, and the high level uses two boundaries: red and yellow. When the number of entries exceeds the red boundary, the high level deletes the oldest entries.ro Enumeration .1.3.6.1.4.1.89.50.5 |
rlBrgMacSwSpanningTreeSpecifies whether the device supports port the Spanning Tree Protocol.ro Enumeration .1.3.6.1.4.1.89.50.6 |
rlBrgMacSwKeyTypeSpecified the used MAC Address Table kye format: macOnly: One global MAC Address Table per device (leaky VLANs). tagAndMac: MAC Address Table per each VLAN (strick VLANs).ro Enumeration .1.3.6.1.4.1.89.50.7 |
rlBrgMacSwYellowBoundaryThe yellow boundary.rw INTEGER .1.3.6.1.4.1.89.50.8 |
rlBrgMacSwRedBoundaryThe yellow boundary.rw INTEGER .1.3.6.1.4.1.89.50.9 |
rlBrgMacSwTrapEnableThis variable indicates whether to create a SNMP trap if adding dynamic mac failed due to full hash chain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.50.10 |
rlBrgMacSwOperTrapCountThis variable indicates the trap counter status (i.e. number of received MAC addresses since the last trap sent that haven't been inserted into the hash). It is relevant only when trap is enabled.ro INTEGER .1.3.6.1.4.1.89.50.11 |
rlBrgMacSwAdminTrapFrequencyThis variable indicates the minimal frequency (in seconds) of sending a trap. It is relevant only when trap is enabled.rw INTEGER (1 .. 86400) -- UNITS "seconds" .1.3.6.1.4.1.89.50.12 |
More MIBs from Rnd
Browse all RndMIBs →Standard SNMP MIB module defining data structures for RADLAN-MIB.
Standard SNMP MIB module defining data structures for RADWARE-MIB.
The RADLAN-IPV6FHS-MIB enables monitoring and management of IPv6 First Hop Security (FHS) mechanisms, specifically tracking Neighbor Discovery Protocol (NDP) states, binding table entries, and security policy violations on RADLAN network devices. This module facilitates the detection of rogue routers, duplicate address detection failures, and unauthorized neighbor advertisements to enforce Layer 2/Layer 3 security boundaries.
SNMP MIB module
SNMP MIB module
The LINKSYS-POLICY-MIB enables monitoring and configuration of generic traffic policy rules, including bandwidth limits and QoS classifications, on Linksys networking hardware via SNMP. This private module exposes specific policy identifiers, action states, and associated traffic counters to facilitate granular traffic management and enforcement.