DMA200-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for DMA200-MIB.
33
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
33 total| Object Name |
|---|
gdc OBJECT IDENTIFIER .1.3.6.1.4.1.498 |
RFC-1215 Unknown .1.3.6.1.4.1.498 |
sc OBJECT IDENTIFIER .1.3.6.1.4.1.498.3 |
dmaSystem OBJECT IDENTIFIER .1.3.6.1.4.1.498.3.7 |
dmaAccessThe dmaAccess trap is sent whenever the following occurs:
value Condition
- -
local User plugs in a terminal to the front panel
global User enters global mode
local User enters local mode
none User removes front panel terminal TRAP-TYPE .1.3.6.1.4.1.498.3.7.0.1 |
dmaElementAlarmThe dmaElementAlarm trap is sent: a) whenever the dma scans
the active network elements and detects a change in status.
The element number and the current status are sent. This way
the trap is sent when an alarm occurs and when it clears.
b) whenever a network element is logged on to by the DMA
and a mismatch in dmaElementType is found. TRAP-TYPE .1.3.6.1.4.1.498.3.7.0.2 |
dmaMaster OBJECT IDENTIFIER .1.3.6.1.4.1.498.3.7.1 |
dmaMasterFSterminateWhen set, this object will terminate a terminal session
from the front panel FS port. The terminal will display a
message to the user that access is terminated.rw Enumeration .1.3.6.1.4.1.498.3.7.1.1 |
dmaMasterSupvAccessThe value of the supervisory port terminal access on the
DMA-200 master as sent by the trap. Note: when in global
access, this can't be read.ro Enumeration .1.3.6.1.4.1.498.3.7.1.2 |
dmaMasterModemCmdThis is the modem 'AT' command string which can be sent
for modem configuration. When read, it gives the last
response from the modem. If the modem response is greater
than 256 bytes in length, the first 256 bytes are read.rw DisplayString .1.3.6.1.4.1.498.3.7.1.3 |
dmaMasterDialPrefixThis is the modem 'AT' command string which is sent to the
modem before the DialPhoneNumber. The default is ATD.rw DisplayString .1.3.6.1.4.1.498.3.7.1.4 |
dmaMasterDialPhoneNumberThe phone number of the remote node (DMA-200 slave or
PMC-100 slave) to be dialled. If no dial-out phone number is
generated, this value should be set to a zero length string.rw DisplayString .1.3.6.1.4.1.498.3.7.1.5 |
dmaMasterDialingThe value initiating the dial or disconnect activity
of the DMA-200 master dial-out port. No dialing is
initiated if the phone number value is a zero string.rw Enumeration .1.3.6.1.4.1.498.3.7.1.6 |
dmaMasterDialPortStatusThe DMA-200 modem port status at the time of the
SNMP status request.ro Enumeration .1.3.6.1.4.1.498.3.7.1.7 |
dmaMasterResumeScanWhen written, the DMA200 cancels the internal delay timer
and resumes scanning the Network Elements.rw INTEGER .1.3.6.1.4.1.498.3.7.1.8 |
dmaMasterScanCtrlThis object is stored in non-volatile memory and
controls the scanning process. The first time the unit
is powered, the non-volatile memory is set to dmaScanOff.
Setting dmaScanOn will begin the scan process. Setting
dmaScanOff will stop the scan process and clear any current
alarm states.rw Enumeration .1.3.6.1.4.1.498.3.7.1.9 |
dmaNode OBJECT IDENTIFIER .1.3.6.1.4.1.498.3.7.2 |
dmaNodeNumNumber of DMA-200 and PMC-100 nodes in the system.
Firmware revisions E- and below have a maximum of 20 nodes
Firmware revisions F- and above have a maximum of 40 nodesro INTEGER .1.3.6.1.4.1.498.3.7.2.1 |
dmaNodeTableA table that contains information about the nodes in
the system. SEQUENCE OF DmaNodeEntry .1.3.6.1.4.1.498.3.7.2.2 |
dmaNodeEntryA list of information for each node in the system. DmaNodeEntry .1.3.6.1.4.1.498.3.7.2.2.1 |
dmaNodeIndexThe value indicates the node number for which this
entry contains management information.ro INTEGER .1.3.6.1.4.1.498.3.7.2.2.1.1 |
dmaNodeValidThe value indicates the status of the table row entry
for the purpose of creation and deletion of new node
instances.rw Enumeration .1.3.6.1.4.1.498.3.7.2.2.1.2 |
dmaNodePhoneNumberThe phone number of the slave DMA-200 or slave PMC-
100. If no phone number is generated, this value
should be set to a zero length string.rw DisplayString .1.3.6.1.4.1.498.3.7.2.2.1.3 |
dmaNodeNameA textual description of the node ID such as the name
or location of the node site. If no name or location
identification is generated, this value should be set
to a zero length string.rw DisplayString .1.3.6.1.4.1.498.3.7.2.2.1.4 |
dmaElement OBJECT IDENTIFIER .1.3.6.1.4.1.498.3.7.3 |
dmaElementConfigTableA table that contains information about all Network
Elements in the system. SEQUENCE OF DmaElementEntry .1.3.6.1.4.1.498.3.7.3.1 |
dmaElementEntryA list of information for each Network Element DmaElementEntry .1.3.6.1.4.1.498.3.7.3.1.1 |
dmaElementIndexThe value indicates the Network Element numeric
address for which this entry contains management information.ro INTEGER .1.3.6.1.4.1.498.3.7.3.1.1.1 |
dmaElementRemoteIndexThe value indicates the numeric address of the remote
Network Element on the oposite end of the line.rw INTEGER .1.3.6.1.4.1.498.3.7.3.1.1.2 |
dmaElementValidThe value indicates the status of the table row entry
for the purpose of creation and deletion of new Network
Element instances.rw Enumeration .1.3.6.1.4.1.498.3.7.3.1.1.3 |
dmaElementTypeThe value indicates the type the T1-CSU Network Element.
This value is set by the manager and sent with traps.rw Enumeration .1.3.6.1.4.1.498.3.7.3.1.1.4 |
dmaElementStatusThe value indicates the communication status of the
supervisory connection between the DMA-200 Master and
the Network Element at the time of the SNMP status request.ro Enumeration .1.3.6.1.4.1.498.3.7.3.1.1.5 |
dmaElementNodeThe value indicates the node number to which this Network
Element is attached. Same as the corresponding dmaNodeIndex.
A value of zero indicates that this Network Element is
attached to no node.rw INTEGER .1.3.6.1.4.1.498.3.7.3.1.1.6 |