DKSF-70-5-X-X-1
Generic MIB for NetPing remote sensing and control
Main OID:
uniPingServerSolutionV3.1.3.6.1.4.1.25728.70
131
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
131 total| Object Name |
|---|
lightcom OBJECT IDENTIFIER .1.3.6.1.4.1.25728 |
uniPingServerSolutionV3Generic MIB for NetPing remote sensing and control MODULE-IDENTITY .1.3.6.1.4.1.25728.70 |
npTrapInfo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.90 |
npTrapEmailTouser-specified e-mail for NetPing Trap Forwarding Servicero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.90.1 |
npReboot OBJECT IDENTIFIER .1.3.6.1.4.1.25728.911 |
npSoftRebootWrite 1 to reboot device after current operations completitionrw INTEGER .1.3.6.1.4.1.25728.911.1 |
npResetStackWrite 1 to re-initialize network stackrw INTEGER .1.3.6.1.4.1.25728.911.2 |
npForcedRebootWrite 1 to immediate forced rebootrw INTEGER .1.3.6.1.4.1.25728.911.3 |
npGsm OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800 |
npGsmInfo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.1 |
npGsmFailedFirmware's GSM module statusro Enumeration .1.3.6.1.4.1.25728.3800.1.1 |
npGsmRegistrationStatus of modem registration in GSM network (AT+CREG? result)ro Enumeration .1.3.6.1.4.1.25728.3800.1.2 |
npGsmStrengthGSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating inforo INTEGER .1.3.6.1.4.1.25728.3800.1.3 |
npGsmSendSmsSend arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Cyrillic characters must be in UTF8 encoding.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.3800.1.9 |
npGsmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.2 |
npGsmTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.2.0 |
npGsmTrapGSM modem or SMS firmware problems NOTIFICATION-TYPE .1.3.6.1.4.1.25728.3800.2.0.1 |
npRelay OBJECT IDENTIFIER .1.3.6.1.4.1.25728.5500 |
npRelayTableWatchdog and outlet/relay control table SEQUENCE OF NpRelayEntry .1.3.6.1.4.1.25728.5500.5 |
npRelayEntryRelay/outlet table row NpRelayEntry .1.3.6.1.4.1.25728.5500.5.1 |
npRelayNThe N of output relayro INTEGER .1.3.6.1.4.1.25728.5500.5.1.1 |
npRelayModeControl of relay: -1 - flip between on(1) and off(0) 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logicrw Enumeration .1.3.6.1.4.1.25728.5500.5.1.2 |
npRelayStartResetWrite 1 to start reset (switch relay off for some time)rw INTEGER .1.3.6.1.4.1.25728.5500.5.1.3 |
npRelayMemoRelay memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.5500.5.1.6 |
npRelayStateActual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is onro Enumeration .1.3.6.1.4.1.25728.5500.5.1.15 |
npIr OBJECT IDENTIFIER .1.3.6.1.4.1.25728.7900 |
npIrCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.25728.7900.1 |
npIrPlayCmdWrite IR command number to send IR commandrw INTEGER .1.3.6.1.4.1.25728.7900.1.1 |
npIrResetWrite 1 to reset IR transiever. After reset, send IR command and check npIrStatus.rw INTEGER .1.3.6.1.4.1.25728.7900.1.2 |
npIrStatusIR transiever statusro Enumeration .1.3.6.1.4.1.25728.7900.1.3 |
npSmoke OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8200 |
npSmokeTableSmoke Sensors Table SEQUENCE OF NpSmokeEntry .1.3.6.1.4.1.25728.8200.1 |
npSmokeEntrySmoke Sensors Table Row NpSmokeEntry .1.3.6.1.4.1.25728.8200.1.1 |
npSmokeSensorNThe id of 1Wire Smoke sensor, 1 to 4ro INTEGER .1.3.6.1.4.1.25728.8200.1.1.1 |
npSmokeStatusStatus of Smoke sensorro Enumeration .1.3.6.1.4.1.25728.8200.1.1.2 |
npSmokePowerControls power on Smoke sensor current looprw Enumeration .1.3.6.1.4.1.25728.8200.1.1.3 |
npSmokeResetWrite 1 to switch off for approx. 10s to reset sensorrw INTEGER .1.3.6.1.4.1.25728.8200.1.1.4 |
npSmokeMemoSmoke sensor memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8200.1.1.6 |
npSmokeTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8200.2 |
npSmokeTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8200.2.0 |
npSmokeTrapStatus of 1W Smoke sensor has changed NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8200.2.0.1 |
npSmokeTrapSensorNThe id of 1Wire Smoke sensor, 1 to 4ro INTEGER .1.3.6.1.4.1.25728.8200.2.1 |
npSmokeTrapStatusNew status of Smoke sensorro Enumeration .1.3.6.1.4.1.25728.8200.2.2 |
npSmokeTrapMemoSmoke sensor memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8200.2.6 |
npCurLoop OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8300 |
npCurLoopTableCurrent loop sensors Table SEQUENCE OF NpCurLoopEntry .1.3.6.1.4.1.25728.8300.1 |
npCurLoopEntryCurrent loop sensors Table Row NpCurLoopEntry .1.3.6.1.4.1.25728.8300.1.1 |
npCurLoopNIndex of current loop, 1 to max supportedro INTEGER .1.3.6.1.4.1.25728.8300.1.1.1 |
npCurLoopStatusStatus of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Poweredro Enumeration .1.3.6.1.4.1.25728.8300.1.1.2 |
npCurLoopILoop current, mAro INTEGER .1.3.6.1.4.1.25728.8300.1.1.3 |
npCurLoopVVoltage drop on the loop, mVro INTEGER .1.3.6.1.4.1.25728.8300.1.1.4 |
npCurLoopRResistance of the loop, Ohmro INTEGER .1.3.6.1.4.1.25728.8300.1.1.5 |
npCurLoopPowerControl of loop power 0=Off, 1=On, 2=reset by off/on powerrw Enumeration .1.3.6.1.4.1.25728.8300.1.1.7 |
npCurLoopTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8300.2 |
npCurLoopTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8300.2.0 |
npCurLoopTrapStatus of current loop N has changed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8300.2.0.1 |
npCurLoopTrapNIndex of current loop, which status has changedro INTEGER .1.3.6.1.4.1.25728.8300.2.1 |
npCurLoopTrapStatusStatus of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Poweredro Enumeration .1.3.6.1.4.1.25728.8300.2.2 |
npCurLoopTrapILoop current, mAro INTEGER .1.3.6.1.4.1.25728.8300.2.3 |
npCurLoopTrapVVoltage drop on the loop, mVro INTEGER .1.3.6.1.4.1.25728.8300.2.4 |
npCurLoopTrapRResistance of the loop, Ohmro INTEGER .1.3.6.1.4.1.25728.8300.2.5 |
npCurLoopTrapPowerStatus of loop power 0=Off, 1=Onrw Enumeration .1.3.6.1.4.1.25728.8300.2.7 |
npRelHumidity OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400 |
npRelHumTableHumidity+Temperature Sensors Table SEQUENCE OF NpRelHumEntry .1.3.6.1.4.1.25728.8400.1 |
npRelHumEntryHumidity+Temperature Sensors Table Row NpRelHumEntry .1.3.6.1.4.1.25728.8400.1.1 |
npRelHumNIndex of Humidity+Temperature sensor, 1 to max supportedro INTEGER .1.3.6.1.4.1.25728.8400.1.1.1 |
npRelHumValueRelative humidity value, %ro INTEGER .1.3.6.1.4.1.25728.8400.1.1.2 |
npRelHumStatusStatus of Relative Humidutyro Enumeration .1.3.6.1.4.1.25728.8400.1.1.3 |
npRelHumTempValueSensor temperature, deg.Cro INTEGER (-60..200) .1.3.6.1.4.1.25728.8400.1.1.4 |
npRelHumTempStatusStatus of Relative Humidutyro Enumeration .1.3.6.1.4.1.25728.8400.1.1.5 |
npRelHumMemoSensor Memo/Locationro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8400.1.1.6 |
npRelHumSafeRangeHighRelative Humidity safe range, top margin, %RHro INTEGER .1.3.6.1.4.1.25728.8400.1.1.7 |
npRelHumSafeRangeLowRelative Humidity safe range, bottom margin, %RHro INTEGER .1.3.6.1.4.1.25728.8400.1.1.8 |
npRelHumTempSafeRangeHighTemperature safe range, top margin, deg.Cro INTEGER (-55..150) .1.3.6.1.4.1.25728.8400.1.1.9 |
npRelHumTempSafeRangeLowTemperature safe range, bottom margin, deg.Cro INTEGER (-55..150) .1.3.6.1.4.1.25728.8400.1.1.10 |
npRelHumTrapData OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.3 |
npRelHumTrapDataNIndex of Humidity+Temperature sensor, 1 to max supportedro INTEGER .1.3.6.1.4.1.25728.8400.3.1 |
npRelHumTrapDataValueSensor humidity, %RH, or temperature, deg.Cro INTEGER .1.3.6.1.4.1.25728.8400.3.2 |
npRelHumTrapDataStatusStatus of humidity or temperaturero Enumeration .1.3.6.1.4.1.25728.8400.3.4 |
npRelHumTrapDataMemoSensor Memo/Locationro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8400.3.6 |
npRelHumTrapDataSafeRangeHighRelative Humidity safe range, top margin, %RH or deg.Cro INTEGER .1.3.6.1.4.1.25728.8400.3.7 |
npRelHumTrapDataSafeRangeLowRelative Humidity safe range, bottom margin, %RH or deg.Cro INTEGER .1.3.6.1.4.1.25728.8400.3.8 |
npRelHumTrap OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.6 |
npRelHumTrapFailRel.Humidity sensor failed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.6.100 |
npRelHumTrapBelowSafeHumidity below the Safe range NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.6.101 |
npRelHumTrapSafeHumidity in the Safe range NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.6.102 |
npRelHumTrapAboveSafeHumidity above the Safe range NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.6.103 |
npRelHumTrapAllEvents OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.6.127 |
npRelHumTrapAllChannelsStatus of Humidity has changed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.6.127.99 |
npRelHumTrapTemp OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.7 |
npRelHumTrapTempFailSensor failed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.7.100 |
npRelHumTrapTempBelowSafeTemperature below the Safe range NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.7.101 |
npRelHumTrapTempSafeTemperature in the Safe range NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.7.102 |
npRelHumTrapTempAboveSafeTemperature above the Safe range NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.7.103 |
npRelHumTrapTempAllEvents OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.7.127 |
npRelHumTrapTempAllChannelsStatus of Temperature has changed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.7.127.99 |
npThermo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800 |
npThermoTableThermo Sensors Table SEQUENCE OF NpThermoEntry .1.3.6.1.4.1.25728.8800.1 |
npThermoEntryThermo Sensors Table Row NpThermoEntry .1.3.6.1.4.1.25728.8800.1.1 |
npThermoSensorNThe id of temperature sensor, 1 to 8ro INTEGER .1.3.6.1.4.1.25728.8800.1.1.1 |
npThermoValueTemperature, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.2 |
npThermoStatusTemperature status (0=fault, 1=underheat, 2=normal, 3=overheat)ro Enumeration .1.3.6.1.4.1.25728.8800.1.1.3 |
npThermoLowBottom margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.4 |
npThermoHighTop margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.5 |
npThermoMemoT channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8800.1.1.6 |
npThermoTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800.2 |
npThermoTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800.2.0 |
npThermoTrapStatus of Thermo sensor is changed (crossing of normal temp. range) NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8800.2.0.1 |
npThermoTrapSensorNThe id of temperature sensor, 1 to 8ro INTEGER .1.3.6.1.4.1.25728.8800.2.1 |
npThermoTrapValueTemperature, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.2 |
npThermoTrapStatusTemperature status (0=fault, 1=underheat, 2=normal, 3=overheat)ro Enumeration .1.3.6.1.4.1.25728.8800.2.3 |
npThermoTrapLowBottom margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.4 |
npThermoTrapHighTop margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.5 |
npThermoTrapMemoT channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8800.2.6 |
npIo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900 |
npIoTableDigital Input/output Table SEQUENCE OF NpIoEntry .1.3.6.1.4.1.25728.8900.1 |
npIoEntryDigital Input/output Table Row NpIoEntry .1.3.6.1.4.1.25728.8900.1.1 |
npIoLineNNumber of IO line, from 1 to max supportedro INTEGER .1.3.6.1.4.1.25728.8900.1.1.1 |
npIoLevelInInput level, 0 or 1ro INTEGER .1.3.6.1.4.1.25728.8900.1.1.2 |
npIoLevelOutOutput level, 0 or 1. Write -1 to flip output.rw Enumeration .1.3.6.1.4.1.25728.8900.1.1.3 |
npIoMemoIO line memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8900.1.1.6 |
npIoPulseCounterPulse Counter on IO input line (counts positive fronts) Write 0 to reset.rw Counter32 .1.3.6.1.4.1.25728.8900.1.1.9 |
npIoSinglePulseDurationSet duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100msrw INTEGER .1.3.6.1.4.1.25728.8900.1.1.12 |
npIoSinglePulseStartWrite 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDurationrw INTEGER .1.3.6.1.4.1.25728.8900.1.1.13 |
npIoTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900.2 |
npIoTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900.2.0 |
npIoTrapInput state of IO line is changed NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8900.2.0.1 |
npIoTrapLineNTrap data, Number of IO linero INTEGER .1.3.6.1.4.1.25728.8900.2.1 |
npIoTrapLevelInTrap data, new Input level, 0 or 1ro INTEGER .1.3.6.1.4.1.25728.8900.2.2 |
npIoTrapMemoTrap data, IO line memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8900.2.6 |
npIoTrapLevelLegendLegend for current logic level on the IO linero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8900.2.7 |