DKSF-48-4-X-X-1
Generic MIB for NetPing remote sensing and control
Main OID:
netPing8Pwr.1.3.6.1.4.1.25728.48
98
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
98 total| Object Name |
|---|
lightcom OBJECT IDENTIFIER .1.3.6.1.4.1.25728 |
netPing8PwrGeneric MIB for NetPing remote sensing and control MODULE-IDENTITY .1.3.6.1.4.1.25728.48 |
npReboot OBJECT IDENTIFIER .1.3.6.1.4.1.25728.911 |
npSoftRebootWrite 1 to reboot device after current operations completitionrw INTEGER .1.3.6.1.4.1.25728.911.1 |
npResetStackWrite 1 to re-initialize network stackrw INTEGER .1.3.6.1.4.1.25728.911.2 |
npForcedRebootWrite 1 to immediate forced rebootrw INTEGER .1.3.6.1.4.1.25728.911.3 |
npGsm OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800 |
npGsmInfo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.1 |
npGsmFailedFirmware's GSM module statusro Enumeration .1.3.6.1.4.1.25728.3800.1.1 |
npGsmRegistrationStatus of modem registration in GSM network (AT+CREG? result)ro Enumeration .1.3.6.1.4.1.25728.3800.1.2 |
npGsmStrengthGSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating inforo INTEGER .1.3.6.1.4.1.25728.3800.1.3 |
npGsmSendSmsSend arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Only Latin characters allowed in message bodyrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.3800.1.9 |
npGsmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.2 |
npGsmTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.2.0 |
npGsmTrapGSM modem or SMS firmware problems NOTIFICATION-TYPE .1.3.6.1.4.1.25728.3800.2.0.1 |
npRelay OBJECT IDENTIFIER .1.3.6.1.4.1.25728.5500 |
npRelayTableWatchdog and outlet/relay control table SEQUENCE OF NpRelayEntry .1.3.6.1.4.1.25728.5500.5 |
npRelayEntryRelay/outlet table row NpRelayEntry .1.3.6.1.4.1.25728.5500.5.1 |
npRelayNThe N of output relayro INTEGER .1.3.6.1.4.1.25728.5500.5.1.1 |
npRelayModeControl of relay: 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logicrw Enumeration .1.3.6.1.4.1.25728.5500.5.1.2 |
npRelayStartResetWrite 1 to start reset (switch relay off for some time)rw INTEGER .1.3.6.1.4.1.25728.5500.5.1.3 |
npRelayMemoRelay memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.5500.5.1.6 |
npRelayFlipWrite -1 to flip between manual on and manual off states of relayro Enumeration .1.3.6.1.4.1.25728.5500.5.1.14 |
npRelayStateActual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is onro Enumeration .1.3.6.1.4.1.25728.5500.5.1.15 |
npRelayPoweredAC presence on output. 0 - no AC dew to relay switched off or no ac on input 1 - AC is presentro Enumeration .1.3.6.1.4.1.25728.5500.5.1.16 |
npPwr OBJECT IDENTIFIER .1.3.6.1.4.1.25728.5800 |
npPwrTableWatchdog and outlet/relay control table SEQUENCE OF NpPwrEntry .1.3.6.1.4.1.25728.5800.3 |
npPwrEntryWatchdog control table row NpPwrEntry .1.3.6.1.4.1.25728.5800.3.1 |
npPwrChannelNThe id of watchdog/power channelro INTEGER .1.3.6.1.4.1.25728.5800.3.1.1 |
npPwrStartResetDeprecated in current FW version: Write 1 to start forced reset. On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active or watchdog is inactiveroobsolete INTEGER .1.3.6.1.4.1.25728.5800.3.1.2 |
npPwrResetsCounterCounter of watchdog resets Write 0 to clear.rw INTEGER .1.3.6.1.4.1.25728.5800.3.1.4 |
npPwrRepeatingResetsCounterCounter of continous failed watchdog resetsro INTEGER .1.3.6.1.4.1.25728.5800.3.1.5 |
npPwrMemoWatchdog channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.5800.3.1.6 |
npIr OBJECT IDENTIFIER .1.3.6.1.4.1.25728.7900 |
npIrCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.25728.7900.1 |
npIrPlayCmdWrite IR command number to send IR commandrw INTEGER .1.3.6.1.4.1.25728.7900.1.1 |
npIrResetWrite 1 to reset IR transiever. After reset, send IR command and check npIrStatus.rw INTEGER .1.3.6.1.4.1.25728.7900.1.2 |
npIrStatusIR transiever statusro Enumeration .1.3.6.1.4.1.25728.7900.1.3 |
npSmoke OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8200 |
npSmokeTableSmoke Sensors Table SEQUENCE OF NpSmokeEntry .1.3.6.1.4.1.25728.8200.1 |
npSmokeEntrySmoke Sensors Table Row NpSmokeEntry .1.3.6.1.4.1.25728.8200.1.1 |
npSmokeSensorNThe id of 1Wire Smoke sensor, 1 to 4ro INTEGER .1.3.6.1.4.1.25728.8200.1.1.1 |
npSmokeStatusStatus of Smoke sensorro Enumeration .1.3.6.1.4.1.25728.8200.1.1.2 |
npSmokePowerControls power on Smoke sensor current looprw Enumeration .1.3.6.1.4.1.25728.8200.1.1.3 |
npSmokeResetWrite 1 to switch off for approx. 10s to reset sensorrw INTEGER .1.3.6.1.4.1.25728.8200.1.1.4 |
npSmokeMemoSmoke sensor memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8200.1.1.6 |
npSmokeTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8200.2 |
npSmokeTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8200.2.0 |
npSmokeTrapStatus of 1W Smoke sensor has changed NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8200.2.0.1 |
npSmokeTrapSensorNThe id of 1Wire Smoke sensor, 1 to 4ro INTEGER .1.3.6.1.4.1.25728.8200.2.1 |
npSmokeTrapStatusNew status of Smoke sensorro Enumeration .1.3.6.1.4.1.25728.8200.2.2 |
npSmokeTrapMemoSmoke sensor memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8200.2.6 |
npRelHumidity OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400 |
npRelHumSensor OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.2 |
npRelHumSensorValueHRelative humidity value, %ro INTEGER .1.3.6.1.4.1.25728.8400.2.2 |
npRelHumSensorStatusStatus of the Rel.Humidity Sensor One 1=Normal, 0=Error or Sensor isn't connectedro Enumeration .1.3.6.1.4.1.25728.8400.2.3 |
npRelHumSensorValueTSensor temperature, deg.Cro INTEGER (-60..200) .1.3.6.1.4.1.25728.8400.2.4 |
npRelHumSensorStatusHStatus of Relative Humidutyro Enumeration .1.3.6.1.4.1.25728.8400.2.5 |
npRelHumSafeRangeHighRelative Humidity safe range, top margin, %RHro INTEGER .1.3.6.1.4.1.25728.8400.2.7 |
npRelHumSafeRangeLowRelative Humidity safe range, bottom margin, %RHro INTEGER .1.3.6.1.4.1.25728.8400.2.8 |
npRelHumSensorValueT100Sensor temperature, deg.C * 100 (fixed point two decimal places) Used to get access to the fractional part of T valuero Integer32 .1.3.6.1.4.1.25728.8400.2.9 |
npRelHumTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.9 |
npRelHumTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.9.0 |
npRelHumTrapStatus of Relative Humidity RH sensor has changed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.9.0.1 |
npThermo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800 |
npThermoTableThermo Sensors Table SEQUENCE OF NpThermoEntry .1.3.6.1.4.1.25728.8800.1 |
npThermoEntryThermo Sensors Table Row NpThermoEntry .1.3.6.1.4.1.25728.8800.1.1 |
npThermoSensorNThe id of temperature sensor, 1 to 8ro INTEGER .1.3.6.1.4.1.25728.8800.1.1.1 |
npThermoValueTemperature, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.2 |
npThermoStatusTemperature status (0=fault, 1=underheat, 2=normal, 3=overheat)ro Enumeration .1.3.6.1.4.1.25728.8800.1.1.3 |
npThermoLowBottom margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.4 |
npThermoHighTop margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.5 |
npThermoMemoT channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8800.1.1.6 |
npThermoTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800.2 |
npThermoTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800.2.0 |
npThermoTrapStatus of Thermo sensor is changed (crossing of normal temp. range) NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8800.2.0.1 |
npThermoTrapSensorNThe id of temperature sensor, 1 to 8ro INTEGER .1.3.6.1.4.1.25728.8800.2.1 |
npThermoTrapValueTemperature, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.2 |
npThermoTrapStatusTemperature status (0=fault, 1=underheat, 2=normal, 3=overheat)ro Enumeration .1.3.6.1.4.1.25728.8800.2.3 |
npThermoTrapLowBottom margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.4 |
npThermoTrapHighTop margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.5 |
npThermoTrapMemoT channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8800.2.6 |
npIo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900 |
npIoTableDigital Input/output Table SEQUENCE OF NpIoEntry .1.3.6.1.4.1.25728.8900.1 |
npIoEntryDigital Input/output Table Row NpIoEntry .1.3.6.1.4.1.25728.8900.1.1 |
npIoLineNNumber of IO line, from 1 to max supportedro INTEGER .1.3.6.1.4.1.25728.8900.1.1.1 |
npIoLevelInInput level, 0 or 1ro INTEGER .1.3.6.1.4.1.25728.8900.1.1.2 |
npIoLevelOutOutput level, 0 or 1rw INTEGER .1.3.6.1.4.1.25728.8900.1.1.3 |
npIoMemoIO line memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8900.1.1.6 |
npIoPulseCounterPulse Counter on IO input line (counts positive fronts) Write 0 to reset.rw Counter32 .1.3.6.1.4.1.25728.8900.1.1.9 |
npIoSinglePulseDurationSet duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100msrw INTEGER .1.3.6.1.4.1.25728.8900.1.1.12 |
npIoSinglePulseStartWrite 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDurationrw INTEGER .1.3.6.1.4.1.25728.8900.1.1.13 |
npIoTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900.2 |
npIoTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900.2.0 |
npIoTrapInput state of IO line is changed NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8900.2.0.1 |
npIoTrapLineNTrap data, Number of IO linero INTEGER .1.3.6.1.4.1.25728.8900.2.1 |
npIoTrapLevelInTrap data, new Input level, 0 or 1ro INTEGER .1.3.6.1.4.1.25728.8900.2.2 |
npIoTrapMemoTrap data, IO line memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8900.2.6 |