DKSF-202-9-X-X-1
AI MIB Summary
The DKSF-202-9-X-X-1 MIB module facilitates remote monitoring and control of NetPing sensing hardware, specifically exposing metrics for ping latency, packet loss, interface status, and device availability states via SNMP.
Generic MIB for NetPing remote sensing and control
Main OID:
netPing2PWR220SMSv2.1.3.6.1.4.1.25728.202
95
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
95 total| Object Name |
|---|
lightcom OBJECT IDENTIFIER .1.3.6.1.4.1.25728 |
npTrapInfo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.90 |
npTrapEmailTouser-specified e-mail for NetPing Trap Forwarding Servicero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.90.1 |
netPing2PWR220SMSv2Generic MIB for NetPing remote sensing and control MODULE-IDENTITY .1.3.6.1.4.1.25728.202 |
npReboot OBJECT IDENTIFIER .1.3.6.1.4.1.25728.911 |
npSoftRebootWrite 1 to reboot device after current operations completitionrw INTEGER .1.3.6.1.4.1.25728.911.1 |
npResetStackWrite 1 to re-initialize network stackrw INTEGER .1.3.6.1.4.1.25728.911.2 |
npForcedRebootWrite 1 to immediate forced rebootrw INTEGER .1.3.6.1.4.1.25728.911.3 |
npGsm OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800 |
npGsmInfo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.1 |
npGsmFailedFirmware's GSM module statusro Enumeration .1.3.6.1.4.1.25728.3800.1.1 |
npGsmRegistrationStatus of modem registration in GSM network (AT+CREG? result)ro Enumeration .1.3.6.1.4.1.25728.3800.1.2 |
npGsmStrengthGSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating inforo INTEGER .1.3.6.1.4.1.25728.3800.1.3 |
npGsmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.2 |
npGsmTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3800.2.0 |
npGsmTrapGSM modem or SMS firmware problems NOTIFICATION-TYPE .1.3.6.1.4.1.25728.3800.2.0.1 |
npBattery OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3900 |
npBatteryInfo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3900.1 |
npBatteryPokPower sourcero Enumeration .1.3.6.1.4.1.25728.3900.1.1 |
npBatteryLevelBattery charge, approximate value, in percent. Valid only if npBatteryPok = 0ro INTEGER .1.3.6.1.4.1.25728.3900.1.2 |
npBatteryChgBattery chargeing status. 0 if charging suspended or battery is full, 1 while LiPo fast charging.ro Enumeration .1.3.6.1.4.1.25728.3900.1.3 |
npBatteryTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3900.2 |
npBatteryTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.3900.2.0 |
npBatteryTrapStatus of PowerOk has changed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.3900.2.0.1 |
npRelay OBJECT IDENTIFIER .1.3.6.1.4.1.25728.5500 |
npRelayTableWatchdog and outlet/relay control table SEQUENCE OF NpRelayEntry .1.3.6.1.4.1.25728.5500.5 |
npRelayEntryRelay/outlet table row NpRelayEntry .1.3.6.1.4.1.25728.5500.5.1 |
npRelayNThe N of output relayro INTEGER .1.3.6.1.4.1.25728.5500.5.1.1 |
npRelayModeControl of relay: 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logicrw Enumeration .1.3.6.1.4.1.25728.5500.5.1.2 |
npRelayStartResetWrite 1 to start reset (switch relay off for some time)rw INTEGER .1.3.6.1.4.1.25728.5500.5.1.3 |
npRelayMemoRelay memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.5500.5.1.6 |
npRelayFlipWrite -1 to flip between manual on and manual off states of relayro Enumeration .1.3.6.1.4.1.25728.5500.5.1.14 |
npRelayStateActual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is onro Enumeration .1.3.6.1.4.1.25728.5500.5.1.15 |
npPwr OBJECT IDENTIFIER .1.3.6.1.4.1.25728.5800 |
npPwrTableWatchdog and outlet/relay control table SEQUENCE OF NpPwrEntry .1.3.6.1.4.1.25728.5800.3 |
npPwrEntryWatchdog and outlet/relay control table row NpPwrEntry .1.3.6.1.4.1.25728.5800.3.1 |
npPwrChannelNThe id of watchdog/power channelro INTEGER .1.3.6.1.4.1.25728.5800.3.1.1 |
npPwrStartResetWrite 1 to start forced reset On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active or watchdog is inactiverw INTEGER .1.3.6.1.4.1.25728.5800.3.1.2 |
npPwrManualModeMode of power channel 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - schedule and watchdog 5 - controlled by Logicrw Enumeration .1.3.6.1.4.1.25728.5800.3.1.3 |
npPwrResetsCounterCounter of watchdog resets Write 0 to clear.rw INTEGER .1.3.6.1.4.1.25728.5800.3.1.4 |
npPwrRepeatingResetsCounterCounter of continous failed watchdog resetsro INTEGER .1.3.6.1.4.1.25728.5800.3.1.5 |
npPwrMemoRelay channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.5800.3.1.6 |
npPwrRelayFlipWrite -1 to flip between manual on and manual off states of relayrw Enumeration .1.3.6.1.4.1.25728.5800.3.1.14 |
npPwrRelayStateActual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is onro Enumeration .1.3.6.1.4.1.25728.5800.3.1.15 |
npIr OBJECT IDENTIFIER .1.3.6.1.4.1.25728.7900 |
npIrCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.25728.7900.1 |
npIrPlayCmdWrite IR command number to send IR commandrw INTEGER .1.3.6.1.4.1.25728.7900.1.1 |
npIrResetWrite 1 to reset IR transiever. After reset, send IR command and check npIrStatus.rw INTEGER .1.3.6.1.4.1.25728.7900.1.2 |
npIrStatusIR transiever statusro Enumeration .1.3.6.1.4.1.25728.7900.1.3 |
npRelHumidity OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400 |
npRelHumSensor OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.2 |
npRelHumSensorValueHRelative humidity value, %ro INTEGER .1.3.6.1.4.1.25728.8400.2.2 |
npRelHumSensorStatusStatus of the Rel.Humidity Sensor One 0=Normal, 1=Error or Sensor isn't connectedro Enumeration .1.3.6.1.4.1.25728.8400.2.3 |
npRelHumSensorValueTSensor temperature, deg.Cro INTEGER (-60..200) .1.3.6.1.4.1.25728.8400.2.4 |
npRelHumSensorStatusHStatus of Relative Humidutyro Enumeration .1.3.6.1.4.1.25728.8400.2.5 |
npRelHumSafeRangeHighRelative Humidity safe range, top margin, %RHro INTEGER .1.3.6.1.4.1.25728.8400.2.7 |
npRelHumSafeRangeLowRelative Humidity safe range, bottom margin, %RHro INTEGER .1.3.6.1.4.1.25728.8400.2.8 |
npRelHumSensorValueT100Sensor temperature, deg.C * 100 (fixed point two decimal places) Used to get access to the fractional part of T valuero Integer32 .1.3.6.1.4.1.25728.8400.2.9 |
npRelHumTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.9 |
npRelHumTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8400.9.0 |
npRelHumTrapStatus of Relative Humidity RH sensor has changed! NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8400.9.0.1 |
npThermo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800 |
npThermoTableThermo Sensors Table SEQUENCE OF NpThermoEntry .1.3.6.1.4.1.25728.8800.1 |
npThermoEntryThermo Sensors Table Row NpThermoEntry .1.3.6.1.4.1.25728.8800.1.1 |
npThermoSensorNThe id of temperature sensor, 1 to 8ro INTEGER .1.3.6.1.4.1.25728.8800.1.1.1 |
npThermoValueTemperature, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.2 |
npThermoStatusTemperature status (0=fault, 1=underheat, 2=normal, 3=overheat)ro Enumeration .1.3.6.1.4.1.25728.8800.1.1.3 |
npThermoLowBottom margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.4 |
npThermoHighTop margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.1.1.5 |
npThermoMemoT channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8800.1.1.6 |
npThermoTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800.2 |
npThermoTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8800.2.0 |
npThermoTrapStatus of Thermo sensor is changed (crossing of normal temp. range) NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8800.2.0.1 |
npThermoTrapSensorNThe id of temperature sensor, 1 to 8ro INTEGER .1.3.6.1.4.1.25728.8800.2.1 |
npThermoTrapValueTemperature, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.2 |
npThermoTrapStatusTemperature status (0=fault, 1=underheat, 2=normal, 3=overheat)ro Enumeration .1.3.6.1.4.1.25728.8800.2.3 |
npThermoTrapLowBottom margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.4 |
npThermoTrapHighTop margin of normal temperature range, deg.Cro INTEGER (-60..280) .1.3.6.1.4.1.25728.8800.2.5 |
npThermoTrapMemoT channel memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8800.2.6 |
npIo OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900 |
npIoTableDigital Input/output Table SEQUENCE OF NpIoEntry .1.3.6.1.4.1.25728.8900.1 |
npIoEntryDigital Input/output Table Row NpIoEntry .1.3.6.1.4.1.25728.8900.1.1 |
npIoLineNNumber of IO line, from 1 to max supportedro INTEGER .1.3.6.1.4.1.25728.8900.1.1.1 |
npIoLevelInInput level, 0 or 1ro INTEGER .1.3.6.1.4.1.25728.8900.1.1.2 |
npIoLevelOutOutput levelrw Enumeration .1.3.6.1.4.1.25728.8900.1.1.3 |
npIoMemoIO line memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8900.1.1.6 |
npIoPulseCounterPulse Counter on IO input line (counts positive fronts) Write 0 to reset.rw Counter32 .1.3.6.1.4.1.25728.8900.1.1.9 |
npIoSinglePulseDurationSet duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100msrw INTEGER .1.3.6.1.4.1.25728.8900.1.1.12 |
npIoSinglePulseStartWrite 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDurationrw INTEGER .1.3.6.1.4.1.25728.8900.1.1.13 |
npIoTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900.2 |
npIoTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.25728.8900.2.0 |
npIoTrapInput state of IO line is changed NOTIFICATION-TYPE .1.3.6.1.4.1.25728.8900.2.0.1 |
npIoTrapLineNTrap data, Number of IO linero INTEGER .1.3.6.1.4.1.25728.8900.2.1 |
npIoTrapLevelInTrap data, new Input level, 0 or 1ro INTEGER .1.3.6.1.4.1.25728.8900.2.2 |
npIoTrapMemoTrap data, IO line memoro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25728.8900.2.6 |