CISCO-WAN-FR-X21-MIB
AI MIB Summary
The CISCO-WAN-FR-X21-MIB manages the configuration and alarm states of Cisco WAN interfaces utilizing X.21 and HSSI physical layer standards, specifically monitoring interface status, electrical signaling parameters, and logical link states for high-speed serial data communication.
The MIB module to configure X.21/HSSI physical and logical interfaces. This MIB module also contains alarm configuration of X.21 interfaces. Terminologies Used: HSSI : High Speed Serial Interface. The HSSI defines both electrical and physical interfaces on DTE and DCE devices. It operates at the physical layer of the OSI reference model. This provides high-speed data communication over WAN and LAN links.
Main OID:
ciscoWanFrX21MIB.1.3.6.1.4.1.351.150.49
58
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
58 total| Object Name |
|---|
x21CnfGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.5.1 |
x21CnfGrpTableThe X21 Configuration table. The table size is given by the value of x21LineNumofValidEntries. SEQUENCE OF X21CnfGrpEntry .1.3.6.1.4.1.351.110.4.5.1.1 |
x21CnfGrpEntryAn entry in the X21 Configuration table. X21CnfGrpEntry .1.3.6.1.4.1.351.110.4.5.1.1.1 |
x21LineNumThis object is the identifier of a X.21 interface. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8.ro Integer32 .1.3.6.1.4.1.351.110.4.5.1.1.1.1 |
x21LineEnableThis variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify Default is enable.rw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.2 |
x21LineTypeThis variable indicates the type X21 line type. The line-type affects the clock -- the DCE device always provides the clock and DTE accepts it. dteST is only applicable to V.35 interfaces Default is DTE.rw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.3 |
x21LineRateThis variable configures the X.21/HSSI/V.35 line-rate. Note that enumerations 51 through 108 are supported only by FRSM-HS2/HS2B card. default is r48Kbps on FRSM-HS2B-12IN1 default is r52Mbps on FRSM-HS2/HS2B-HSSIrw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.4 |
x21LineLoopbackCommandThis variable represents the loopback state x21NoLoop Not in the loopback state. Normal traffic can be sent x21DiagnosticMetallicLoop Loopbacks the line on the back-card towards the Network. x21DiagnosticFrontcardLoop Loopbacks the line on the frontcard toward the Network. x21RemoteLoop The remote NTU is in the loop back mode. In this state, the FRSM-HS1 is sending the loopback code to remote NTU. Default is x21NoLoop. Note: Before going into one of the loopbacks the state should be x21NoLoop.rw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.5 |
x21LineSendCodeThis variable indicates what type of code is being sent across the X.21/HSSI interface by the device. The values mean: x21NoCode: No loopback. x21SendLoopACode: Start sending Loop A code. Valid only if the backcard is HSSI and the line-type is DTE. This command loops the line module of the remote device. x21SendLoopBCode: Start sending Loop B code. Valid only if the backcard is HSSI and the line-type is DTE. This command loops the digital section of the remote device. x21SendLocalLoopCode: Start sending CCITT X.21 Loopback Type 3 code. This is valid only if the backcard is X.21 type. x21SendRemoteLoopCode: Start sending CCITT X.21 Loopback Type 2 code. This is valid only if the backcard is X.21 type. x21SendUnLoopCode: Sending a loopback termination request. Valid for both HSSI and X.21 lines. To execute any of the loop-codes the x21LineLoopbackCommand should be set to x21RemoteLoop. Once the x21SendUnLoopCode succeeds the x21LineLoopbackCommand would transition back to x21NoLoop state. Default is x21NoCode.rw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.6 |
x21LineLoopbackCodeDetectionEnable detection of line Loopback Codes. The loopback detection is implemented only in HSSI DCE mode. Default is codeDetectDisabled.rw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.7 |
x21ConnectorTypeback card type This object is not used by FRSM-HS2/HS2Bro Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.8 |
x21InvertClockThis object configures two options: a) To invert the clock sent by HS1/HS2B with the TX data or not. b) If DCE,to expect the receive clock looped back from DTE or not. If DTE,to loop back the receive clock from DCE or not. nonInvertedAndNotLooped(1)- a)=dont invert, b)=dont expect rcv clock/ dont loop rcv clock invertedAndNotLooped(2) - a)=invert, b)=dont expect rcv clock/ dont loop rcv clock nonInvertedAndLooped(3) - a)=dont invert, b)=expect rcv clock/ loop rcv clock invertedAndLooped(4) - a)=invert, b)=expect rcv clock/ loop rcv clock Enums 1 and 2 are applicable for X.21/HSSI/V.35 interfaces. Enums 3 and 4 are applicable only for V.35. Default for X.21/HSSI is nonInvertedAndNotLooped(1) Default for V.35 is nonInvertedAndLooped(3) This object is not used by FRSM-HS2/FRSM-HS2B-HSSI This object is used by FRSM-HS2B-12IN1 and default values are nonInvertedAndNotLooped(1) for X.21, nonInvertedAndLooped(3) for V.35.rw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.9 |
x21LineInterfaceTypeThis object indicates serial interface type. Default is hssi(1). This object is not is configurable in FRSM-HS2 and FRSM-HS2B-HSSI. It will be set to hssi(1) by default for these cards This object is configurable in FRSM-H2B-12IN1. Default is v35(3).rw Enumeration .1.3.6.1.4.1.351.110.4.5.1.1.1.10 |
x21ClkFrequencyThresholdThis object indicates user configurable percentage of clock frequency, which is used by DTE clock monitoring to declare clock rate out of bound alarm. This object is valid only for X.21/v.35/HSSI DTE interfaces. This object is supported by FRSM-HS2 and FRSM-HS2/Brw Integer32 .1.3.6.1.4.1.351.110.4.5.1.1.1.11 |
serialLineRateLine rate for X.21/HSSI/V.35 interfaces in bps. This object is supported only by FRSM-HS2/B card, only multiples of 1000 are accepted. Default is 48Kbps for X.21/V.35 interfaces and 51840Kbps for HSSI interface.rw Integer32 .1.3.6.1.4.1.351.110.4.5.1.1.1.12 |
serialLineRateVariationThis object indicates line rate variation of HSSI/X.21/V.35 DCE interfaces in ppm (parts per million). i.e. clock generated from DCE hardware interface = (serialLineRate +/- (serialLineRateVariation * 10^6)/ serialLineRate) This object is supported only by FRSM-HS2/B cardro Integer32 .1.3.6.1.4.1.351.110.4.5.1.1.1.13 |
x21LineNumofValidEntriesThe number of X.21/HSSI configuration entries (regardless of their current configuration) in the x21ConfigTable table.ro Integer32 .1.3.6.1.4.1.351.110.4.5.1.2 |
x21AlmCnfGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.5.2 |
x21AlmCnfGrpTableThe FRSM-HS1/HS2 interface alarm configuration table. SEQUENCE OF X21AlmCnfGrpEntry .1.3.6.1.4.1.351.110.4.5.2.1 |
x21AlmCnfGrpEntryAn entry in the X.21/HSSI Alarm Configuration table. X21AlmCnfGrpEntry .1.3.6.1.4.1.351.110.4.5.2.1.1 |
x21AlmCnfLineNumX.21/HSSI line number. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8.rw Integer32 .1.3.6.1.4.1.351.110.4.5.2.1.1.1 |
x21SeverityThis variable is used to setup the severity of LOS(Loss of Signal) or clock mismatch alarm. Whenever the above condition arises, the FRSM-HS1/HS2/HS2B will send the alarm with appropriate status.rw Enumeration .1.3.6.1.4.1.351.110.4.5.2.1.1.2 |
x21AlmGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.5.3 |
x21AlmGrpTableThe X.21/HSSI interface alarm configuration table. SEQUENCE OF X21AlmGrpEntry .1.3.6.1.4.1.351.110.4.5.3.1 |
x21AlmGrpEntryAn entry in the X21 Alarm table X21AlmGrpEntry .1.3.6.1.4.1.351.110.4.5.3.1.1 |
x21AlmLineNumThis object is the identifier (line number) of a X.21/HSSI interface. The value for this object must be same as the value of x21LineNum.ro Integer32 .1.3.6.1.4.1.351.110.4.5.3.1.1.1 |
x21LineAlarmStateThis variable is a bitmap of the X21 Line ALarms on the FRSM-HS1. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 C/I signal is OFF (also used to indicate LOS) 1 Clock rate mismatch (used in DTE mode) 2 Internal Loopback (diagnostic loopback) 3 HSSI Local LoopA (line is in loopback) 4 HSSI Local LoopB (line is in loopback) 5 Remote Loopback (line is transmitting loopcodes) 6 For V35 DTE mode, DCD and CTS both are inactive 7 For V35 DCE mode, RTS is inactive 8 No cable attached to V35 backcard 9 Wrong cable attached to V35 backcard If all the bit-states are 0s: - line is not in alarm, or - line not in loopback, or - line is transmitting any loopback codes.ro Integer32 .1.3.6.1.4.1.351.110.4.5.3.1.1.2 |
x21LineEIAStatusIndicates the status of X.21/HSSI lines: 0x01 -- c-lead high 0x02 -- i-lead high 0x04 -- LC-lead high (valid only for HSSI DCE mode).ro Integer32 (0..'10'h) .1.3.6.1.4.1.351.110.4.5.3.1.1.3 |
x21AlarmClrButtonThis variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm.rw Enumeration .1.3.6.1.4.1.351.110.4.5.3.1.1.4 |
frPortCnfX21PortGrpTableThe config table is for X.21/HSSI logical port interface SEQUENCE OF FrPortCnfX21PortGrpEntry .1.3.6.1.4.1.351.110.5.1.1.1.3.1 |
frPortCnfX21PortGrpEntryAn entry for logical port. FrPortCnfX21PortGrpEntry .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1 |
x21portNumThis is logical port number. The HSSI backcard can support upto 3 ports. The X.21 back card can support 4 logical ports.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.1 |
x21portLineNumThis represents the line number. On FRSM-HS1 the HSSI can support 3 lines and X.21 4 lines.rw Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.2 |
x21portRowStatusThis variable adds, deletes, or modifies the port 1- add 2 - delete 3 - modify Default is add.rw Enumeration .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.3 |
x21portFlagsBetweenFramesNumber of flags transmitted between two consecutive HDLC frames. Default is 1 flag.rw Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.4 |
x21portEqueueServiceRatioNumber of times queue 1 is serviced for every time queue 2 is serviced. Default is 1.rw Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.5 |
x21portSpeedPort speed in kbps. At present it is same as line speed.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.6 |
x21portAdminThis object is used for administratively changing the status of the port. Up/down used to up and down the port. Default is the up state.rw Enumeration .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.7 |
x21portTypeThis represents port type. The processing of the frames depends on the type of the port.rw Enumeration .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.8 |
x21portSvcStatusThis represents SVC status.rw Enumeration .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.9 |
x21portSvcInUseThis represents port SVC in use.rw Enumeration .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.10 |
x21portSvcShareLcnThis represents port type.ro Enumeration .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.11 |
x21portSvcLcnLowThis represents low end of reserved LCN for SVC.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.12 |
x21portSvcLcnHighThis represents high end of reserved LCN for SVC.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.13 |
x21portSvcDlciLowThis represents low end of reserved DLCI for SVC.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.14 |
x21portSvcDlciHighThis represents high end of reserved DLCI for SVC.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.15 |
x21portDeleteSvcsSetting this object to 1 indicates that all the SVC connections on the given port has to be deleted.rw Enumeration .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.16 |
x21portIngrSvcBandWThis represents Ingress Bandwidth reserve for SVC.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.17 |
x21portEgrSvcBandWThis represents Egress Bandwidth reserve for SVC.ro Integer32 .1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.18 |
ciscoWanFrX21MIBThe MIB module to configure X.21/HSSI physical and logical interfaces. This MIB module also contains alarm configuration of X.21 interfaces. Terminologies Used: HSSI : High Speed Serial Interface. The HSSI defines both electrical and physical interfaces on DTE and DCE devices. It operates at the physical layer of the OSI reference model. This provides high-speed data communication over WAN and LAN links. MODULE-IDENTITY .1.3.6.1.4.1.351.150.49 |
cwfX21MIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.49.2 |
cwfX21MIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.49.2.1 |
ciscoWanFrX21PortGroupThe collection of objects which are applicable for X21 ports in frame relay. Unknown .1.3.6.1.4.1.351.150.49.2.1.1 |
ciscoWanFrX21LineGroupThe collection of objects which are related to x21 lines. Unknown .1.3.6.1.4.1.351.150.49.2.1.2 |
ciscoWanFrX21AlarmConfGroupThe collection of objects which are related to x21 lines. Unknown .1.3.6.1.4.1.351.150.49.2.1.3 |
ciscoWanFrX21AlarmGroupThe collection of objects which are related to x21 lines. Unknown .1.3.6.1.4.1.351.150.49.2.1.4 |
cwfX21MIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.49.2.2 |
cwfX21ComplianceThe compliance statement for objects related to Frame Relay Ports. Unknown .1.3.6.1.4.1.351.150.49.2.2.1 |