CISCO-MGX82XX-SONET-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CISCO-MGX82XX-SONET-MIB.
272
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
272 total| Object Name |
|---|
sonetConfig OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.6.1.1 |
BASIS-MIB Unknown .1.3.6.1.4.1.351.110.4.6.1.1 |
sonetConfigTableThe SONET Configuration table. There is one row for each
SONET port in the BASIS system. The table size (number of
rows) is given by the value of sonetLineNumOfValidEntries. SEQUENCE OF SonetConfigEntry .1.3.6.1.4.1.351.110.4.6.1.1.1 |
sonetConfigEntryAn entry in the SONET Configuration table. SonetConfigEntry .1.3.6.1.4.1.351.110.4.6.1.1.1.1 |
sonetLineNumThis object is the identifier of a SONET
Interface on a managed device.
For MGX8850(For example PXM1 Module):
OC-3 : sonetLineNum in a range 1..4
OC-12: sonetLineNum = 1 is the ONLY valid number
For Other: sonetLineNum = 1 is the ONLY valid numberro INTEGER .1.3.6.1.4.1.351.110.4.6.1.1.1.1.1 |
sonetLineTypeThis variable indicates the cell framing.
Defaults to Sts-3crw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.2 |
sonetLineLoopbackCommandThis variable represents the loopback configuration
of the SONET interface.
The values mean:
sonetNoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
the interface shall always return this as
it's value.
sonetRemoteLineLoop
Near End loops back Remote data
sonetLocalLineLoop
Near End loops back Local data.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.3 |
sonetHCSmaskingHCS masking. Defaults to enable.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.4 |
sonetPayloadScramblingSTS3c or STM-1 payload scrambling. Defaults to enable.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.5 |
sonetFrameScramblingSTS3c or STM-1 frame scrambling. Defaults to enable.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.6 |
sonetLineEnableThis variable indicates if the line is enabled or not
defaults to disablerw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.7 |
sonetLineXmtClkSrcThis represents the type of transmit clock source.
backplaneClk: clock source is from the controller card,
transmitted via the backplane to the service module.
recoverClk: clock is recovered from the received signal.
localClk: clock is from a local oscillator on the card.
Default is backplaneClk.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.8 |
sonetRDIVTypeThis variable represents the type of RDI-V
sent by this NE to remote NE.
onebit: use 1 bit RDI-V. Compatible with older equipment.
threebit: use 3 bit, enhanced RDI-V.
Defaults to onebit.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.9 |
sonetRDIPTypeThis variable represents the type of RDI-P
sent by this NE to remote NE.
onebit: use 1 bit RDI-P. Compatible with older equipment.
threebit: use 3 bit, enhanced RDI-P.
Defaults to onebit.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.10 |
sonetTributaryTypeType of tributary carried within the
Sonet/Sdh signal.
vt15vc11: carries T1 signals (VT15 or VC11)
vt2vc12: carries E1 signals (VT2 or VC12)
Default is vt15vc11 for Sonet interfaces and
vt2vc12 for SDH interfaces.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.11 |
sonetTributaryMappingTypeType of VT/VC mapping.
asynchronous: In this mode, the channel structure
of the DS1/E1 is neither visible nor preserved.
byteSynchronous: In this mode, the DS0 channels inside
the VC/VT can be found and extracted.
Default is asynchronous.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.12 |
sonetTributaryFramingFormatType of vt framing format. Is applicable
only in byte-sync mapping mode for T1 tributaries.
notApplicable: if VT mapping is not byte-sync.
sf: superframe format.
esf: extended superframe format.
Default is esf if sonetTributaryMappingType is set to
byteSynchronous, else the default is notApplicable.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.13 |
sonetSignallingTransportModeThe mode used to transport DS0 signalling
information for T1 byte-sync mapping.
notApplicable: if byte-sync mapping is not used.
signallingTransferMode: the robbed bit signalling
is transferred into the S bits of the VT header
and framing bit is discarded.
clearMode: only the framing bit is transferred to
VT header. The signalling bits are left intact
in the VT payload.
Default is signallingTransferMode if sonetTributaryMappingType
is set to byteSynchronous, else the default is notApplicable.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.14 |
sonetTributaryGroupingTypeThis variable indicates the method used to group
VCs into an STM-1 signal. Applicable only to SDH.
notApplicable: for sonet interfaces.
au3Grouping: STM-1 <- AU-3 <- TUG-2 <- TU-12 <- VC12 or
STM-1 <- AU-3 <- TUG-2 <- TU-11 <- VC11.
au4Grouping: STM-1 <- AU-4 <- TUG-3 <- TUG-2 <- TU-12 <- VC12 or
STM-1 <- AU-4 <- TUG-3 <- TUG-2 <- TU-11 <- VC11.
Defaults to au3Grouping for SDH interfaces and notApplicable for
Sonet interfaces.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.1.1.1.15 |
sonetConfigNumOfValidEntriesThe number of SONET configuration entries (regardless
of their current configuration) in the sonetConfigTable.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.1.2 |
cwsonetMedium OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.6.1.2 |
cwSonetMediumTableSonet medium table parameters SEQUENCE OF CwSonetMediumEntry .1.3.6.1.4.1.351.110.4.6.1.2.1 |
cwSonetMediumEntryAn entry in the SONET/SDH Medium table. CwSonetMediumEntry .1.3.6.1.4.1.351.110.4.6.1.2.1.1 |
cwSonetMediumTypeThis variable identifies whether a SONET
or a SDH signal is used across this interface.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.2.1.1.1 |
cwSonetMediumTimeElapsedThe number of seconds, including partial
seconds, that have elapsed since the beginning of
the mandatory error-measurement period.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.2.1.1.2 |
cwSonetMediumValidIntervalsThe number of previous intervals for which valid
data has been stored. A SONET device must support
at least n intervals.
The minimum value of n is 4.
The default of n is 32.
The maximum value of n is 96.
The value of this object will be n unless
the device was brought online within the last
(nx15) minutes, in which case the value will be the
number of complete 15 minute intervals the device has
been online.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.2.1.1.3 |
cwSonetMediumLineCodingThis variable describes the line coding for
this interface. The B3ZS and CMI are used for
electrical SONET/SDH signals (STS-1 and STS-3).
The Non-Return to Zero (NRZ) and the Return
to Zero are used for optical SONET/SDH signals.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.2.1.1.4 |
cwSonetMediumLineTypeThis variable describes the line type for
this interface. The line types are
Short and Long Range
Single Mode fiber or Multi-Mode fiber interfaces,
and coax and UTP for electrical interfaces. The
value sonetOther should be used when the Line Type is
not one of the listed values.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.2.1.1.5 |
cwSonetMediumCircuitIdentifierThis variable contains the transmission
vendor's circuit identifier, for the
purpose of facilitating troubleshooting.ro DisplayString .1.3.6.1.4.1.351.110.4.6.1.2.1.1.6 |
cwsonetSection OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.6.1.3 |
cwSonetSectionCurrentTableThe SONET/SDH Section Current table. SEQUENCE OF CwSonetSectionCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.3.1 |
cwSonetSectionCurrentEntryAn entry in the SONET/SDH Section Current table. CwSonetSectionCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.3.1.1 |
cwSonetSectionCurrentLineNumline number.
There are Max 1 line Numro INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.1.1.1 |
cwSonetSectionCurrentStatusThis variable indicates the status of the sonet section layer.
The cwSonetSectionCurrentStatus is a bit map represented
as a sum, therefore, it can represent multiple defects
simultaneously.
The sonetSectionNoDefect should be set if and only if
no other flag is set.
The various bit positions are:
bit 1 = sonetSectionNoDefect
bit 2 = sonetSectionLOS
bit 3 = sonetSectionLOFro INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.1.1.2 |
cwSonetSectionCurrentValidFlagIndicates if the current 15min bucket is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.1.1.3 |
cwSonetSectionCurrent15minTimeElapsedThe number of seconds, including partial seconds,
that have elapsed since the beginning of the 15min
error-measurement period.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.1.1.4 |
cwSonetSectionCurrentESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Section in the current 15 minute interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.1.1.5 |
cwSonetSectionCurrentSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Section in the current 15
minute interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.1.1.6 |
cwSonetSectionCurrentSEFSsThe counter associated with the number of
Severely Errored Framing Seconds
encountered by a SONET/SDH Section in the current
15 minute interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.1.1.7 |
cwSonetSectionCurrentCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Section in the current 15 minute interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.1.1.8 |
cwSonetSectionCurrentClrButtonClears all the Section's Current15min counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.1.1.9 |
sonetSectionCurrentDayTableThe SONET/SDH Section CurrentDay table. SEQUENCE OF SonetSectionCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.3.2 |
sonetSectionCurrentDayEntryAn entry in the SONET/SDH Section CurrentDay table. SonetSectionCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.3.2.1 |
sonetSectionCurrentDayLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.2.1.1 |
sonetSectionCurrentDayValidFlagIndicates if the current day bucket is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.2.1.2 |
sonetSectionCurrentDayESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Section in the CurrentDay one day interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.2.1.3 |
sonetSectionCurrentDaySESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Section in the CurrentDay
minute interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.2.1.4 |
sonetSectionCurrentDaySEFSsThe counter associated with the number of
Severely Errored Framing Seconds
encountered by a SONET/SDH Section in the CurrentDay
one day interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.2.1.5 |
sonetSectionCurrentDayCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Section in the CurrentDay one day interval.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.2.1.6 |
sonetSectionCurrentDayClrButtonClears all the Section's Current Day counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.2.1.7 |
cwSonetSectionIntervalTableThe SONET/SDH Section Interval table. SEQUENCE OF CwSonetSectionIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.3.3 |
cwSonetSectionIntervalEntryAn entry in the SONET/SDH Section Interval table. CwSonetSectionIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.3.3.1 |
cwSonetSectionIntervalLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.3.1.1 |
cwSonetSectionIntervalNumberA number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.3.1.2 |
cwSonetSectionIntervalValidFlagIndicates if the bucket specified by the interval
is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.3.1.3 |
cwSonetSectionIntervalESsThe counter associated with the number of
Errored Seconds encountered
by a SONET/SDH Section in a
particular 15-minute interval
in the past 24 hours.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.3.1.4 |
cwSonetSectionIntervalSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Section in a
particular 15-minute interval
in the past 24 hours.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.3.1.5 |
cwSonetSectionIntervalSEFssThe counter associated with the number of
Severely Errored Framing Seconds
encountered by a SONET/SDH Section in a
particular 15-minute interval
in the past 24 hours.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.3.1.6 |
cwSonetSectionIntervalCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Section in a particular 15-minute interval
in the past 24 hours.ro Counter .1.3.6.1.4.1.351.110.4.6.1.3.3.1.7 |
sonetSectionAlarmTableThe SONET/SDH Section Alarm table. SEQUENCE OF SonetSectionAlarmEntry .1.3.6.1.4.1.351.110.4.6.1.3.4 |
sonetSectionAlarmEntryAn entry in the SONET/SDH Section Alarm table. SonetSectionAlarmEntry .1.3.6.1.4.1.351.110.4.6.1.3.4.1 |
sectionAlarmLineNumline number.
BNM has 1 linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.1 |
sonetSectionStatisticalAlarmSeverityWhen any statistical threshold is exceeded.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.4.1.2 |
sonetSectionCurrent15minESsThresholdThe default is set to 20.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.3 |
sonetSectionCurrentDayESsThresholdThe default is set to 200.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.4 |
sonetSectionCurrent15minSESsThresholdThe default is set to 3.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.5 |
sonetSectionCurrentDaySESsThresholdThe default is set to 7.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.6 |
sonetSectionCurrent15minSEFSsThresholdThe default is set to 3.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.7 |
sonetSectionCurrentDaySEFSsThresholdThe default is set to 7.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.8 |
sonetSectionCurrent15minCVsThresholdThe default is set to 25.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.9 |
sonetSectionCurrentDayCVsThresholdThe default is set to 250.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.4.1.10 |
sonetSectionTraceSelectionSonet Section Trace Selection.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.4.1.11 |
sonetSectionTraceToTransmitSonet Section Trace To Transmit. 16-64 bytes String.
If 16 byte trace is selected, FW will only
use bytes 0-15 of the string.rw OCTET STRING .1.3.6.1.4.1.351.110.4.6.1.3.4.1.12 |
sonetSectionTraceToExpectSonet Section Trace To Expect. 16-64 bytes String.
If 16 byte trace is selected, FW will only
use bytes 0-15 of the string.rw OCTET STRING .1.3.6.1.4.1.351.110.4.6.1.3.4.1.13 |
sonetSectionTraceReceivedSonet Section Trace Received. 16-64 bytes String.
The write option is for debugging only.rw OCTET STRING .1.3.6.1.4.1.351.110.4.6.1.3.4.1.14 |
sonetSectionStatAlarmStatusThis variable indicates the
status of the interface.
The sonetSectionStatAlarmStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetLineStatAlarmNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetSectionStatAlarmNoDefect
2 sonetSectionCurrent15minESs
3 sonetSectionCurrent15minSESs
4 sonetSectionCurrent15minSEFSs
5 sonetSectionCurrent15minCVs
6 sonetSectionCurrentDayESs
7 sonetSectionCurrentDaySESs
8 sonetSectionCurrentDaySEFSs
9 sonetSectionCurrentDayCVsrw INTEGER (1..'1FF'h) .1.3.6.1.4.1.351.110.4.6.1.3.4.1.15 |
sonetSectionCounterTableThe SONET/SDH Section Counter table. SEQUENCE OF SonetSectionCounterEntry .1.3.6.1.4.1.351.110.4.6.1.3.5 |
sonetSectionCounterEntryAn entry in the SONET/SDH Section table. SonetSectionCounterEntry .1.3.6.1.4.1.351.110.4.6.1.3.5.1 |
sectionCounterLineNumline number.
There are Max 1 line on the BNMro INTEGER .1.3.6.1.4.1.351.110.4.6.1.3.5.1.1 |
sonetSectionCounterLOSsThe counter associated with the number of LOSs
encountered by a SONET/SDH.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.3.5.1.2 |
sonetSectionCounterLOFsThe counter associated with the number of
LOFs encountered by a SONET/SDH Section.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.3.5.1.3 |
sonetSectionCounterClrButtonClears all the Section's counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.3.5.1.4 |
cwsonetLine OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.6.1.4 |
cwSonetLineCurrentTableThe SONET/SDH Line Current table. SEQUENCE OF CwSonetLineCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.4.1 |
cwSonetLineCurrentEntryAn entry in the SONET/SDH Line Current table. CwSonetLineCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.4.1.1 |
cwSonetLineCurrentLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.1.1.1 |
cwSonetLineCurrentStatusThis variable indicates the status of the sonet line layer.
The cwSonetLineCurrentStatus is a bit map represented
as a sum, therefore, it can represent multiple defects
simultaneously.
The sonetLineNoDefect should be set if and only if
no other flag is set.
The various bit positions are:
bit 1 = sonetLineNoDefect
bit 2 = sonetLineRcvAIS
bit 3 = sonetLineRcvRDI
bit 4 = sonetLineXmtAis
bit 5 = sonetLineXmtRdiro INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.1.1.2 |
cwSonetLineCurrentValidFlagIndicates if the current 15min bucket is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.1.1.3 |
cwSonetLineCurrent15minTimeElapsedThe number of seconds, including partial seconds,
that have elapsed since the beginning of the 15min
error-measurement period.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.1.1.4 |
cwSonetLineCurrentESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Line in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.1.1.5 |
cwSonetLineCurrentSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Line in the current 15
minute
interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.1.1.6 |
cwSonetLineCurrentCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Line in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.1.1.7 |
cwSonetLineCurrentUASsThe counter associated with the number of
Unavailable Seconds
encountered by a SONET/SDH Line in the current 15
minute
interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.1.1.8 |
cwSonetLineCurrentClrButtonClears all the SONET Line's Current15min counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.1.1.9 |
sonetLineCurrentDayTableThe SONET/SDH Line Current Day table. SEQUENCE OF SonetLineCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.4.2 |
sonetLineCurrentDayEntryAn entry in the SONET/SDH Line Current Day table. SonetLineCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.4.2.1 |
lineCurrentDayLineNumline number.
BNM has 1 linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.2.1.1 |
sonetLineCurrentDayValidFlagIndicates if the current day bucket is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.2.1.2 |
sonetLineCurrentDayESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Line in the current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.2.1.3 |
sonetLineCurrentDaySESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Line in the current
day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.2.1.4 |
sonetLineCurrentDayCVsThe counter associated with the number of Coding
Violations (BIP-8*N for STS-N) encountered by a
SONET/SDH Line in the current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.2.1.5 |
sonetLineCurrentDayFCsNumber of times that line was in AIS alarm in the
current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.2.1.6 |
sonetLineCurrentDayUASsThe counter associated with the number of
Unavailable Seconds
encountered by a SONET/SDH Line in the current
day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.2.1.7 |
sonetLineCurrentDayClrButtonClears all the SONET Line's CurrentDay counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.2.1.8 |
cwSonetLineIntervalTableThe SONET/SDH Line Interval table. SEQUENCE OF CwSonetLineIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.4.3 |
cwSonetLineIntervalEntryAn entry in the SONET/SDH Line Interval table. CwSonetLineIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.4.3.1 |
cwSonetLineIntervalLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.3.1.1 |
cwSonetLineIntervalNumberA number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.3.1.2 |
cwSonetLineIntervalValidFlagIndicates if the bucket specified by the interval
is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.3.1.3 |
cwSonetLineIntervalESsThe counter associated with the number of
Errored Seconds encountered
by a SONET/SDH Line in a
particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.3.1.4 |
cwSonetLineIntervalSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Line in a
particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.3.1.5 |
cwSonetLineIntervalCVsThe counter associated with the number of Coding
Violations (BIP-8*N) encountered by a
SONET/SDH Line in a
particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.3.1.6 |
cwSonetLineIntervalFCsNumber of times that line was in AIS alarm in the
particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.3.1.7 |
cwSonetLineIntervalUASsThe counter associated with the
number of Unavailable Seconds
encountered by a SONET/SDH Line in
a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.3.1.8 |
cwSonetFarEndLineCurrentTableThe SONET/SDH Far End Line Current table. SEQUENCE OF CwSonetFarEndLineCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.4.4 |
cwSonetFarEndLineCurrentEntryAn entry in the SONET/SDH Far End Line Current
table. CwSonetFarEndLineCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.4.4.1 |
cwSonetFELineCurrentLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.4.1.1 |
cwSonetFarEndLineCurrentValidFlagIndicates if the Far End current 15min bucket is
valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.4.1.2 |
cwSonetFarEndLineCurrentTimeElapsedThe number of seconds, including partial seconds,
that have elapsed since the beginning of the 15min
error-measurement period.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.4.1.3 |
cwSonetFarEndLineCurrentESsThe counter associated with the number of Far
Far End Errored Seconds encountered by a SONET/SDH
interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.4.1.4 |
cwSonetFarEndLineCurrentSESsThe counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Medium/Section/Line
interface in the current 15 minute
interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.4.1.5 |
cwSonetFarEndLineCurrentCVsThe counter associated with the number of
Far End Coding Violations reported via
the far end block error (FEBE) count
encountered by a
SONET/SDH Medium/Section/Line
interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.4.1.6 |
cwSonetFarEndLineCurrentFCsThe counter associated with the number of
RFI failures occurred in the current 15 min.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.4.1.7 |
cwSonetFarEndLineCurrentUASsThe counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Medium/Section/Line
interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.4.1.8 |
cwSonetFarEndLineCurrentClrButtonClears all the SONET Far End
Line's Current 15min counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.4.1.9 |
sonetFarEndLineCurrentDayTableThe SONET/SDH Far End Line CurrentDay table. SEQUENCE OF SonetFarEndLineCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.4.5 |
sonetFarEndLineCurrentDayEntryAn entry in the SONET/SDH Far End Line CurrentDay
table. SonetFarEndLineCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.4.5.1 |
sonetFELineCurrentDayLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.5.1.1 |
sonetFarEndLineCurrentDayValidFlagIndicates if the Far End current day bucket is valid
or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.5.1.2 |
sonetFarEndLineCurrentDayESsThe counter associated with the number of Far
Far End Errored Seconds encountered by a SONET/SDH
interface in the current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.5.1.3 |
sonetFarEndLineCurrentDaySESsThe counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Medium/Section/Line
interface in the current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.5.1.4 |
sonetFarEndLineCurrentDayCVsThe counter associated with the number of
Far End Coding Violations reported via
the far end block error (FEBE) count
encountered by a
SONET/SDH Medium/Section/Line
interface in the current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.5.1.5 |
sonetFarEndLineCurrentDayFCsThe counter associated with the number of
RFI failures occurred in the current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.5.1.6 |
sonetFarEndLineCurrentDayUASsThe counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Medium/Section/Line
interface in the current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.5.1.7 |
sonetFarEndLineCurrentDayClrButtonClears all the SONET Far End
Line's Current Day counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.5.1.8 |
cwSonetFarEndLineIntervalTableThe SONET/SDH Far End Line Interval table. SEQUENCE OF CwSonetFarEndLineIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.4.6 |
cwSonetFarEndLineIntervalEntryAn entry in the SONET/SDH Far
End Line Interval table. CwSonetFarEndLineIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.4.6.1 |
cwSonetFELineIntervalLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.6.1.1 |
cwSonetFarEndLineIntervalNumberA number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.6.1.2 |
cwSonetFarEndLineIntervalValidFlagIndicates if the bucket specified by the interval
is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.6.1.3 |
cwSonetFarEndLineIntervalESsThe counter associated with the number of
Far End Errored Seconds encountered
by a SONET/SDH Line
interface in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.6.1.4 |
cwSonetFarEndLineIntervalSESsThe counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Line
interface in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.6.1.5 |
cwSonetFarEndLineIntervalCVsThe counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH Line
interface in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.6.1.6 |
cwSonetFarEndLineIntervalFCsThe counter associated with the number of
RFI failures in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.6.1.7 |
cwSonetFarEndLineIntervalUASsThe counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Line
interface in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.6.1.8 |
sonetLineAlarmTableThe SONET/SDH Line Alarm table. SEQUENCE OF SonetLineAlarmEntry .1.3.6.1.4.1.351.110.4.6.1.4.7 |
sonetLineAlarmEntryAn entry in the SONET/SDH Line Alarm table. SonetLineAlarmEntry .1.3.6.1.4.1.351.110.4.6.1.4.7.1 |
sonetLineAlarmLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.1 |
sonetLineStatisticalAlarmSeverityWhen any statistical threshold is exceeded.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.7.1.2 |
sonetLineCurrent15minESsThresholdThe default is set to 20.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.3 |
sonetLineCurrentDayESsThresholdThe default is set to 200.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.4 |
sonetLineCurrent15minSESsThresholdThe default is set to 3.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.5 |
sonetLineCurrentDaySESsThresholdThe default is set to 7.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.6 |
sonetLineCurrent15minCVsThresholdThe default is set to 25.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.7 |
sonetLineCurrentDayCVsThresholdThe default is set to 250.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.8 |
sonetLineCurrent15minUASsThresholdThe default is set to 10.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.9 |
sonetLineCurrentDayUASsThresholdThe default is set to 10.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.7.1.10 |
sonetLineStatAlarmStatusThis variable indicates the
status of the interface.
The sonetLineStatAlarmStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetLineStatAlarmNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetLineStatAlarmNoDefect
2 sonetLineCurrent15minESs
3 sonetLineCurrent15minSESs
4 sonetLineCurrent15minCVs
5 sonetLineCurrent15minUASs
6 sonetFarEndLineCurrent15minESs
7 sonetFarEndLineCurrent15minSESs
8 sonetFarEndLineCurrent15minCVs
9 sonetFarEndLineCurrent15minUASs
10 sonetLineCurrentDayESs
11 sonetLineCurrentDaySESs
12 sonetLineCurrentDayCVs
13 sonetLineCurrentDayUASs
14 sonetFarEndLineCurrentDayESs
15 sonetFarEndLineCurrentDaySESs
16 sonetFarEndLineCurrentDayCVs
17 sonetFarEndLineCurrentDayUASsro INTEGER (1..'1FFFF'h) .1.3.6.1.4.1.351.110.4.6.1.4.7.1.11 |
sonetLineCounterTableThe SONET/SDH Line Counter table. SEQUENCE OF SonetLineCounterEntry .1.3.6.1.4.1.351.110.4.6.1.4.8 |
sonetLineCounterEntryAn entry in the SONET/SDH Line table. SonetLineCounterEntry .1.3.6.1.4.1.351.110.4.6.1.4.8.1 |
sonetLineCounterLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.4.8.1.1 |
sonetLineCounterAISsThe counter associated with the number of AISs
encountered by a SONET/SDH.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.8.1.2 |
sonetLineCounterRFIsThe counter associated with the number of
RFIs encountered by a SONET/SDH Line.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.4.8.1.3 |
sonetLineCounterClrButtonClears all the Line's counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.4.8.1.4 |
cwsonetPath OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.6.1.5 |
cwSonetPathCurrentTableThe SONET/SDH Path Current table. SEQUENCE OF CwSonetPathCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.5.1 |
cwSonetPathCurrentEntryAn entry in the SONET/SDH Path Current table. CwSonetPathCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.5.1.1 |
cwSonetPathCurrentLineNumline number.
BNM has 1 linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.1.1.1 |
cwSonetPathCurrentStatusThis variable indicates the status of the sonet path layer.
The cwSonetPathCurrentStatus is a bit map represented
as a sum, therefore, it can represent multiple defects
simultaneously.
The sonetPathNoDefect should be set if and only if
no other flag is set.
The various bit positions are:
bit 1 = sonetPathNoDefect
bit 2 = sonetPathRcvLOP
bit 3 = sonetPathRcvAIS
bit 4 = sonetPathRcvRDI
bit 5 = sonetPathUnequipted
bit 6 = sonetPathSignalLabelMismatch
bit 7 = sonetPathTraceFailure
bit 8 = sonetPathXmtAis
bit 9 = sonetPathXmtRdi
bit 10 = sonetPathRcvLOCDro INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.1.1.2 |
cwSonetPathCurrentValidFlagIndicates if the current 15min bucket is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.1.1.3 |
cwSonetPathCurrentTimeElapsedThe number of seconds, including partial seconds,
that have elapsed since the beginning of the 15min
error-measurement period.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.1.1.4 |
cwSonetPathCurrentESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Path in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.1.1.5 |
cwSonetPathCurrentSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Path in the current 15
minute
interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.1.1.6 |
cwSonetPathCurrentCVsThe counter associated with the number of Coding
Violations (BIP-8) encountered by a
SONET/SDH Path in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.1.1.7 |
cwSonetPathCurrentFCsNumber of times that Path was in AIS or LOP
alarm in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.1.1.8 |
cwSonetPathCurrentUASsThe counter associated with the number of
Unavailable Seconds
encountered by a Path in the current
15 minute, interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.1.1.9 |
cwSonetPathCurrentClrButtonClears all the SONET Path's Current counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.1.1.10 |
sonetPathCurrentDayTableThe SONET/SDH Path CurrentDay table. SEQUENCE OF SonetPathCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.5.2 |
sonetPathCurrentDayEntryAn entry in the SONET/SDH Path CurrentDay table. SonetPathCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.5.2.1 |
sonetPathCurrentDayLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.2.1.1 |
sonetPathCurrentDayValidFlagIndicates if the current day bucket is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.2.1.2 |
sonetPathCurrentDayESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Path in the Current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.2.1.3 |
sonetPathCurrentDaySESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Path in the Current
day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.2.1.4 |
sonetPathCurrentDayCVsThe counter associated with the number of Coding
Violations (BIP-8) encountered by a
SONET/SDH Path in the Current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.2.1.5 |
sonetPathCurrentDayFCsNumber of times that Path was in AIS or LOP
alarm in the Current interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.2.1.6 |
sonetPathCurrentDayUASsThe counter associated with the number of
Unavailable Seconds
encountered by a Path in the Current
day, interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.2.1.7 |
sonetPathCurrentDayClrButtonClears all the SONET Path's CurrentDay counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.2.1.8 |
cwSonetPathIntervalTableThe SONET/SDH Path Interval table. SEQUENCE OF CwSonetPathIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.5.3 |
cwSonetPathIntervalEntryAn entry in the SONET/SDH Path Interval table. CwSonetPathIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.5.3.1 |
cwSonetPathIntervalLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.3.1.1 |
cwSonetPathIntervalNumberA number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.3.1.2 |
cwSonetPathIntervalValidFlagIndicates if the bucket specified by the interval
is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.3.1.3 |
cwSonetPathIntervalESsThe counter associated with the number of
Errored Seconds encountered
by a SONET/SDH Path in a
particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.3.1.4 |
cwSonetPathIntervalSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Path in
a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.3.1.5 |
cwSonetPathIntervalCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Path in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.3.1.6 |
cwSonetPathIntervalFCsNumber of times that Path was in AIS or LOP
alarm in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.3.1.7 |
cwSonetPathIntervalUASsThe counter associated with the number of
Unavailable Seconds
encountered by a Path in a
particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.3.1.8 |
cwSonetFarEndPathCurrentTableThe SONET/SDH Far End Path Current table. SEQUENCE OF CwSonetFarEndPathCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.5.4 |
cwSonetFarEndPathCurrentEntryAn entry in the SONET/SDH Far End Path Current table. CwSonetFarEndPathCurrentEntry .1.3.6.1.4.1.351.110.4.6.1.5.4.1 |
cwSonetFEPathCurrentLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.4.1.1 |
cwSonetFarEndPathCurrentValidFlagIndicates if the Far End current 15min bucket is
valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.4.1.2 |
cwSonetFarEndPathCurrentTimeElapsedThe number of seconds, including partial seconds,
that have elapsed since the beginning of the 15min
error-measurement period.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.4.1.3 |
cwSonetFarEndPathCurrentESsThe counter associated with the number of Far
Far End Errored Seconds encountered by a SONET/SDH
interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.4.1.4 |
cwSonetFarEndPathCurrentSESsThe counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Path
interface in the current 15 minute
interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.4.1.5 |
cwSonetFarEndPathCurrentCVsThe counter associated with the number of
Far End Coding Violations reported via
the far end block error (FEBE) count
encountered by a
SONET/SDH Path interface in
the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.4.1.6 |
cwSonetFarEndPathCurrentFCsThe counter associated with the number of
RFIs in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.4.1.7 |
cwSonetFarEndPathCurrentUASsThe counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Path interface in
the current 15 minute interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.4.1.8 |
cwSonetFarEndPathCurrentClrButtonClears all the Far End Path Current counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.4.1.9 |
sonetFarEndPathCurrentDayTableThe SONET/SDH Far End Path CurrentDay table. SEQUENCE OF SonetFarEndPathCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.5.5 |
sonetFarEndPathCurrentDayEntryAn entry in the SONET/SDH Far End Path
CurrentDay table. SonetFarEndPathCurrentDayEntry .1.3.6.1.4.1.351.110.4.6.1.5.5.1 |
sonetFEPathCurrentDayLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.5.1.1 |
sonetFarEndPathCurrentDayValidFlagIndicates if the Far End current day bucket is valid
or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.5.1.2 |
sonetFarEndPathCurrentDayESsThe counter associated with the number of Far
Far End Errored Seconds encountered by a SONET/SDH
interface in the Current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.5.1.3 |
sonetFarEndPathCurrentDaySESsThe counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Path
interface in the Current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.5.1.4 |
sonetFarEndPathCurrentDayCVsThe counter associated with the number of
Far End Coding Violations reported via
the far end block error (FEBE) count
encountered by a
SONET/SDH Path interface in
the Current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.5.1.5 |
sonetFarEndPathCurrentDayFCsThe counter associated with the number of
RFIs in the Current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.5.1.6 |
sonetFarEndPathCurrentDayUASsThe counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Path interface in
the Current day interval.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.5.1.7 |
sonetFarEndPathCurrentDayClrButtonClears all the Far End Path CurrentDay counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.5.1.8 |
cwSonetFarEndPathIntervalTableThe SONET/SDH Far End Path Interval table. SEQUENCE OF CwSonetFarEndPathIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.5.6 |
cwSonetFarEndPathIntervalEntryAn entry in the SONET/SDH Far
End Path Interval table. CwSonetFarEndPathIntervalEntry .1.3.6.1.4.1.351.110.4.6.1.5.6.1 |
cwSonetFEPathIntervalLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.6.1.1 |
cwSonetFarEndPathIntervalNumberA number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1.ro INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.6.1.2 |
cwSonetFarEndPathIntervalValidFlagIndicates if the bucket specified by the interval
is valid or not.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.6.1.3 |
cwSonetFarEndPathIntervalESsThe counter associated with the number of
Far End Errored Seconds encountered
by a SONET/SDH Path interface in a
particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.6.1.4 |
cwSonetFarEndPathIntervalSESsThe counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Path interface
in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.6.1.5 |
cwSonetFarEndPathIntervalCVsThe counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH Path interface
in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.6.1.6 |
cwSonetFarEndPathIntervalFCsThe counter associated with the number of
RFIs in in a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.6.1.7 |
cwSonetFarEndPathIntervalUASsThe counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Path interface in
a particular 15-minute interval
in the past 24 hours.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.6.1.8 |
sonetPathAlarmTableThe SONET/SDH Path Alarm table. SEQUENCE OF SonetPathAlarmEntry .1.3.6.1.4.1.351.110.4.6.1.5.7 |
sonetPathAlarmEntryAn entry in the SONET/SDH Path Alarm table. SonetPathAlarmEntry .1.3.6.1.4.1.351.110.4.6.1.5.7.1 |
sonetPathAlarmLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.1 |
sonetPathStatisticalAlarmSeverityWhen any statistical threshold is exceeded.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.7.1.2 |
sonetPathCurrent15minESsThresholdThe default is set to 20.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.3 |
sonetPathCurrentDayESsThresholdThe default is set to 200.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.4 |
sonetPathCurrent15minSESsThresholdThe default is set to 3.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.5 |
sonetPathCurrentDaySESsThresholdThe default is set to 7.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.6 |
sonetPathCurrent15minCVsThresholdThe default is set to 25.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.7 |
sonetPathCurrentDayCVsThresholdThe default is set to 250.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.8 |
sonetPathCurrent15minUASsThresholdThe default is set to 10.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.9 |
sonetPathCurrentDayUASsThresholdThe default is set to 10.
This threshold is the same for Far End and
Near End.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.7.1.10 |
sonetPathTraceSelectionSonet Path Trace Selection.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.7.1.11 |
sonetPathTraceToTransmitSonet Path Trace To Transmit. 64-bytes String.
If 16 byte trace is selected, FW will only
use bytes 0-15 of the string.rw OCTET STRING .1.3.6.1.4.1.351.110.4.6.1.5.7.1.12 |
sonetPathTraceToExpectSonet Path Trace To Expect. 64-bytes String.
If 16 byte trace is selected, FW will only
use bytes 0-15 of the string.rw OCTET STRING .1.3.6.1.4.1.351.110.4.6.1.5.7.1.13 |
sonetPathTraceReceivedSonet Path Trace Received. 64-bytes String.
The write option is for debugging only.rw OCTET STRING .1.3.6.1.4.1.351.110.4.6.1.5.7.1.14 |
sonetPathStatAlarmStatusThis variable indicates the
status of the interface.
The sonetPathStatAlarmStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetPathStatAlarmNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetPathStatAlarmNoDefect
2 sonetPathCurrent15minESs
3 sonetPathCurrent15minSESs
4 sonetPathCurrent15minCVs
5 sonetPathCurrent15minUASs
6 sonetFarEndPathCurrent15minESs
7 sonetFarEndPathCurrent15minSESs
8 sonetFarEndPathCurrent15minCVs
9 sonetFarEndPathCurrent15minUASs
10 sonetPathCurrentDayESs
11 sonetPathCurrentDaySESs
12 sonetPathCurrentDayCVs
13 sonetPathCurrentDayUASs
14 sonetFarEndPathCurrentDayESs
15 sonetFarEndPathCurrentDaySESs
16 sonetFarEndPathCurrentDayCVs
17 sonetFarEndPathCurrentDayUASsro INTEGER (1..'1FFFF'h) .1.3.6.1.4.1.351.110.4.6.1.5.7.1.15 |
sonetPathCounterTableThe SONET/SDH Path Counter table. SEQUENCE OF SonetPathCounterEntry .1.3.6.1.4.1.351.110.4.6.1.5.8 |
sonetPathCounterEntryAn entry in the SONET/SDH Path table. SonetPathCounterEntry .1.3.6.1.4.1.351.110.4.6.1.5.8.1 |
sonetPathCounterLineNumline number.
BNM has one linero INTEGER .1.3.6.1.4.1.351.110.4.6.1.5.8.1.1 |
sonetPathCounterAISsThe counter associated with the number of AISs
encountered by a SONET/SDH.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.8.1.2 |
sonetPathCounterRFIsThe counter associated with the number of
RFIs encountered by a SONET/SDH Path.ro Gauge .1.3.6.1.4.1.351.110.4.6.1.5.8.1.3 |
sonetPathCounterClrButtonClears all the Path's counters.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.5.8.1.4 |
sonetApsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.6.1.6 |
sonetApsConfigTableThe Sonet APS config table SEQUENCE OF SonetApsConfigEntry .1.3.6.1.4.1.351.110.4.6.1.6.1 |
sonetApsConfigEntryAn entry in the Sonet APS table. Each Entry is
index by the working Line number. SonetApsConfigEntry .1.3.6.1.4.1.351.110.4.6.1.6.1.1 |
apsWorkingSlotThis object is the chassis slot number of the working line
MGX 8x50 PXM: can only be slot 7 or 8.
MGX 8x30 PXM: can only be slot 1 or 2.
MGX 8x50 SRME: can only be slot 15,16,31 or 32
MGX 8x30 SRME: can only be slot 7 or 14rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.6.1.1.1 |
apsWorkingLineThis object is the line number of the working line
OC-3 : sonetLineNum in a range 1..4
OC-12: sonetLineNum = 1 is the ONLY valid numberrw INTEGER .1.3.6.1.4.1.351.110.4.6.1.6.1.1.2 |
apsProtectionSlotThis object is the chassis slot number of the protection line
MGX 8x50 PXM: can only be slot 7 or 8.
MGX 8x30 PXM: can only be slot 1 or 2.
MGX 8x50 SRME: can only be slot 15,16,31 or 32
MGX 8x30 SRME: can only be slot 7 or 14rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.6.1.1.3 |
apsProtectionLineThis object is the line number of the working line
OC-3 : sonetLineNum in a range 1..4
OC-12: sonetLineNum = 1 is the ONLY valid numberrw INTEGER .1.3.6.1.4.1.351.110.4.6.1.6.1.1.4 |
apsEnableThis object is used to enable or disable APS feature
on the working/protection line pairs.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.1.1.5 |
apsArchModeThis object is used to configure APS architecture mode
on the working/protection line pairs. The architecture
modes currently supported are 'dualCardonePlusOne'
(for GR-253) and 'anexAOnePlusOne (for G.783 Annex A).rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.1.1.6 |
apsActiveLineThis object indicates which line is currently active
ob the trunk line.ro Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.1.1.7 |
apsSFBERThis object contains the Bit Error Rate threshold for
Signal Fault detection on the working line.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.6.1.1.8 |
apsSDBERThis object contains the Bit Error Rate threshold for
Signal Degrade detection on the working line. If set to
5, it means SDBER rate = 10 ^^ -5.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.6.1.1.9 |
apsWtrThis object contains interval (in minute) to wait before
attempting to switch back to working line. Not applicable
if the line configure in non-revertive mode.rw INTEGER .1.3.6.1.4.1.351.110.4.6.1.6.1.1.10 |
apsdirectionThis object is used to configure the switching direction
which this APS line support. Unidirectional switch only one
direction. Bidirectional switch in both ends of the line.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.1.1.11 |
apsRevertiveThis object is used to configure the APS revertive or
nonrevertive option. Revertive allows the line to be
switch back to working line after the Wait-To-restore interval
has expired and the working line SF/SD has been cleared.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.1.1.12 |
apsK1K2DisableThis object is used to enable or disable the K1/K2 inband
interface on the protection line.rw Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.1.1.13 |
apsCardFailureCodeThe Sonet APS card failure code
apsProtectBCMissing = protection Back card missing
apsProtectDCMissing = protection Daughter card missing
apsWorkingBCMissing = Working Back card missing
apsWorkingDCMissing = Working Daughter card missing
apsWorkingCdMismatch = Working Card in mismatch/fail state
apsProtectCdMismatch = protection card in mismatch/fail statero Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.2 |
apsLineFailureCodeThe Sonet APS line failure codero Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.3 |
apsLineSwReasonThe Sonet APS line switch reason codero Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.4 |
apsLineSwFailureCodeThe Sonet APS line switch failure codero Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.5 |
apsStandbyLineFailureCodeThe Sonet APS standby line failure codero Enumeration .1.3.6.1.4.1.351.110.4.6.1.6.6 |