CISCO-WAN-CES-PORT-MIB
AI MIB Summary
The CISCO-WAN-CES-PORT-MIB manages Cisco WAN interface parameters for Circuit Emulation Service (CES), specifically configuring TDM over IP encapsulation settings such as clocking modes, framing types, and payload mapping for E1/T1/PDH circuits. It provides visibility into CES port operational states, error counters, and traffic statistics to ensure deterministic latency and synchronization for legacy circuit emulation over packet-switched networks.
The MIB module to configure the Circuit Emulation Service(CES) ports.
Main OID:
ciscoWanCesPortMIB.1.3.6.1.4.1.351.150.40
31
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
31 total| Object Name |
|---|
cesmPort OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.5.3.1 |
cesmPortCnfGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.5.3.1.1 |
cesmPortCnfGrpTableThe config table is for CES logical port. This is used for configuring the port type and number of DS0s and number of Subcircuits in DS0 on the CES port. SEQUENCE OF CesmPortCnfGrpEntry .1.3.6.1.4.1.351.110.5.3.1.1.1 |
cesmPortCnfGrpEntryAn entry for each logical port. Each entry contains information on the port type, DS0s configured and number of DS0 subcircuits. CesmPortCnfGrpEntry .1.3.6.1.4.1.351.110.5.3.1.1.1.1 |
cesPortNumThis object identifies the logical port number. The range support depends upon the type of the service module(Card). - 8 port T1 Card, range is 1..192. - 8 port E1 Card, range is 1..248. - 1 port T3 Card, range is 1..1. Range is caclulated as follows. This can be used for calculating the range for other type of cards. For T1 Card: (24 * Number of T1 Ports) For E1 Card: (31 * Number of E1 Ports).ro Integer32 .1.3.6.1.4.1.351.110.5.3.1.1.1.1.1 |
cesPortRowStatusThis variable enables or modifies the port 1 - add : Add a logical port 2 - del : Delete a logical port 3 - mod : Modify a logical port.rw Enumeration .1.3.6.1.4.1.351.110.5.3.1.1.1.1.2 |
cesPortLineNumThis object represents the line number to which this port is associated. The supported range depends upon the type of service module(card).rw Integer32 .1.3.6.1.4.1.351.110.5.3.1.1.1.1.3 |
cesPortTypeThis object represents port type whether it is carrying subrate circuits. structured : This is for SDT(Structured Data Transfer). This type of port supports following features: * intended to emulate point-to-point fractional DS1 or E1 circuit. * Synchronous timing * Fractional(Nx64 Kbps)DS1/E1 service (Contiguous timeslots only).You can map an Nx64 Kbps channel to any Virtual Channel(VC). unstructured : This is for unstructured data transfer(UDT) All the DS0 time slots are allocated. This type of port supports following features: * intended to emulate point-to-point DS1 or E1 circuit. * Synchronous and Asynchronous timing framingOnVcDisconnect : similar to unstructured during normal operation. In case of channel failure line data will be looped back towards line. strau : only one DS0 time slot is allocated. The value strau(4) value is not supported in CESM-8T1/E1 or CESM-T3E3. CESM-T3E3 card supports value unstructured(2) only.rw Enumeration .1.3.6.1.4.1.351.110.5.3.1.1.1.1.4 |
cesPortDs0ConfigBitMapThis represents bit map of DS0s for a line which are used to form this logical port. Bit 0 represents DS0-1.rw Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.1.1.5 |
cesPortNumOfDs0SlotThis represents number of DS0 time slots configured to this Port. If the cesPortType is strau(4), then this can not have more than 1 DS0 time slot.rw Integer32 .1.3.6.1.4.1.351.110.5.3.1.1.1.1.6 |
cesPortNumOfSCIPerDS0This object represents number of subcircuit in the DS0 time slot. This is applicable only when cesPortType is strau(4). 8 = there are 8 no .of 8kbps links (1 bit) 4 = there are 4 no .of 16kbps links (2 bit) 2 = there are 2 no .of 32kbps links (4 bit) Currently not supported in CESM-8.rw Integer32 .1.3.6.1.4.1.351.110.5.3.1.1.1.1.7 |
cesPortSpeedThis object identifies the configured speed of port. Max speed for T1 = 1544 Max speed for E1 = 2038 Max speed for T3 = 44736 Max speed for E3 = 34368.ro Integer32 .1.3.6.1.4.1.351.110.5.3.1.1.1.1.8 |
cesPortStateThis variable indicates the state of the logical port. The possible values are : notConfigured (1) : Port is not configured active (2) : Port is in active state remoteLoopback (3) : Remote Loopback is set failedDueToLine(4) : Port failed due to some failure in physical line failedDueToSignalling(5) : Port failed due to some Signalling issues. inactive (6) : Port is not active inBert (7) : Bit Error Rate Test(BERT) in progress. farEndRemoteLoopback(8): Far End is in loopback.ro Enumeration .1.3.6.1.4.1.351.110.5.3.1.1.1.1.9 |
cesPortBERTEnableThis variable enables/disables BERT. This object is not supported in CESM-T3E3.rw Enumeration .1.3.6.1.4.1.351.110.5.3.1.1.1.1.10 |
cesPortNextAvailableThis variable contains the next UNUSED logical port number of the possible 32 DS0s * n ports. This number can be used in channel config table, the cesportNextAvailable gets updated if the number gets used to create a logical port. A '0' indicates that no more ports are available.ro Integer32 .1.3.6.1.4.1.351.110.5.3.1.1.2 |
cesPortsUsedLine1Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 1ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.3 |
cesPortsUsedLine2Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 2.ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.4 |
cesPortsUsedLine3Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 3ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.5 |
cesPortsUsedLine4Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for line 4ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.6 |
cesPortsUsedLine5Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 5ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.7 |
cesPortsUsedLine6Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 6ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.8 |
cesPortsUsedLine7Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 7ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.9 |
cesPortsUsedLine8Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 8ro Integer32 (0..'ffffff'h) .1.3.6.1.4.1.351.110.5.3.1.1.10 |
ciscoWanCesPortMIBThe MIB module to configure the Circuit Emulation Service(CES) ports. MODULE-IDENTITY .1.3.6.1.4.1.351.150.40 |
ciscoWanCesPortMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.40.2 |
ciscoWanCesPortMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.40.2.1 |
ciscoWanCesPortsUsedGroupThe collection of objects which are applicable for general information about logical ports. Unknown .1.3.6.1.4.1.351.150.40.2.1.1 |
ciscoWanCesPortConfGroupThe collection of objects which are used to represent Circuit Emulation Service Port information. Unknown .1.3.6.1.4.1.351.150.40.2.1.2 |
ciscoWanCesPortDs0InDs1GroupThe collection of objects related to information on DS0 time slots used in each DS1 line. Unknown .1.3.6.1.4.1.351.150.40.2.1.3 |
ciscoWanCesPortMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.40.2.2 |
ciscoWanCesPortComplianceThe compliance statement for objects related to CES Logical Ports. Unknown .1.3.6.1.4.1.351.150.40.2.2.1 |