CISCO-MGX82XX-RPM-SUBIF-MIB
The CISCO-MGX82XX-RPM-SUBIF-MIB enables SNMP-based provisioning and management of backplane sub-interfaces on Cisco MGX 82xx Route Processor Modules running IOS. It facilitates the configuration and monitoring of logical interface instances within the MGX controller's RPM architecture to support routed traffic segmentation.
Imported Objects
Objects
16 total| Object Name |
|---|
rpmPortTableThis table contains information on subinterfaces
configured on RPM back plane interface. SEQUENCE OF RpmPortEntry .1.3.6.1.4.1.351.110.5.2.9.1.1 |
rpmPortEntryAn entry for the RPM backplane sub interface.
Each entry contains RPM's backplane sub interface number,
its IP address and ATM address. RpmPortEntry .1.3.6.1.4.1.351.110.5.2.9.1.1.1 |
rpmPortSlotNumThis object specifies the the slot number
of the RPM card in MGX shelf.ro INTEGER .1.3.6.1.4.1.351.110.5.2.9.1.1.1.1 |
rpmPortInterfaceThis is the RPM's backplane interface.
Currently there is only one interface and
hence only supported value is 1.ro INTEGER .1.3.6.1.4.1.351.110.5.2.9.1.1.1.2 |
rpmPortSubInterfaceThis object identifies the sub-interface number.
The value 0 is for the sub-interface on the
main interface(rpmPortInterface).ro INTEGER .1.3.6.1.4.1.351.110.5.2.9.1.1.1.3 |
rpmPortRowStatusThis indicates the status of this subinterface.
add(1) : sub-interface is added.
del(2) : sub-interface is deleted.
mod(3) : Set to this value before modifying objects
related to Subinterfaces.ro Enumeration .1.3.6.1.4.1.351.110.5.2.9.1.1.1.4 |
rpmPortIpAddressIP address configured on the sub-interface.ro IpAddress .1.3.6.1.4.1.351.110.5.2.9.1.1.1.5 |
rpmPortSubNetMaskThe subnet mask configured on the sub-interface.ro IpAddress .1.3.6.1.4.1.351.110.5.2.9.1.1.1.6 |
rpmPortStateThis indicates the state of this sub-interface.
notConfigured(1) : Sub-interface is not configured.
active(2) : Sub-interface is in active state.
failed(3) : Sub-interface is in failed state.ro Enumeration .1.3.6.1.4.1.351.110.5.2.9.1.1.1.7 |
ciscoMgx82xxRpmSubIfMIB OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.60 |
RFC1155-SMI Unknown .1.3.6.1.4.1.351.150.60 |
cmrSubIfMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.60.2 |
cmrSubIfMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.60.2.1 |
cmrSubIfMIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.60.2.1.1 |
cmrSubIfMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.60.2.2 |
cmrSubIfMIBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.60.2.2.1 |
More MIBs from Stratacom
Browse all StratacomMIBs →Standard SNMP MIB module defining data structures for CISCO-WAN-AXIPOP-MIB.
Standard SNMP MIB module defining data structures for STRATACOM-MIB.
The CISCO-WAN-SVC-MIB manages ATM service provisioning, configuration, and status monitoring on Cisco BPX-SES and MGX ATM switches, specifically tracking XPVC/XPVP segments, OAM cell handling, and ENNI auto-discovery via ILMI. It facilitates the administration of ATM traffic classes (CBR, VBR, UBR, ABR) and virtual circuit states (SVC, SPVC) across User-Network and Network-Network interfaces.
Standard SNMP MIB module defining data structures for CISCO-MGX82XX-SONET-MIB.
The CISCO-MGX82XX-DSX3-MIB enables configuration and monitoring of DS3/E3 interface parameters, including alarm states (AIS, LOF, RAI), performance statistics, and Bit Error Rate Testing (BERT) on Cisco MGX 8220/8230 T3/E3 service modules such as the CESM-T3E3 and FRSM-VHS. This module facilitates the management of physical layer convergence procedures (PLCP) and maintenance byte fields (Tx/Rx MA) defined by ITU-T G.832 for channelized T3 and E3 circuits.
The CISCO-WAN-PAR-MIB manages the Portable AutoRoute (PAR) controller on Cisco MGX and BPX switches to provision, monitor, and alarm connections while controlling LMI communication and clocking selection. It enables the configuration of routing capabilities, failure event conditioning, and the management of feeder-to-node signaling and switch synchronization.