CISCO-MGX82XX-DSX1-MIB
AI MIB Summary
The CISCO-MGX82XX-DSX1-MIB manages DS1/E1 interface parameters and alarm configurations on Cisco MGX 82xx T1/E1 service modules. It enables the monitoring of physical layer metrics and the enforcement of alarm thresholds for T1 and E1 circuit operations.
The MIB module to configure DS1/E1 interface objects. This mib also contains the alarm configuration of DS1/E1 interfaces. This mib is supported in T1/E1 service modules.
Main OID:
ciscoMgx82xxDsx1MIB.1.3.6.1.4.1.351.150.58
104
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
104 total| Object Name |
|---|
dsx1CnfGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.3.1.1 |
dsx1CnfGrpTableThe DS1/E1 Configuration table. The table size is given by the value of lineNumofValidEntries SEQUENCE OF Dsx1CnfGrpEntry .1.3.6.1.4.1.351.110.4.3.1.1.1 |
dsx1CnfGrpEntryAn entry in the DS1 Configuration table. Dsx1CnfGrpEntry .1.3.6.1.4.1.351.110.4.3.1.1.1.1 |
lineNumThis object is the identifier of a DS1/E1 Interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS1/E1 interface, it should have the same value as ifIndex. Otherwise, number the ds1LineIndices with an unique identifier following the rules of choosing a number that is greater than ifNumber and numbering the inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g, network side) with odd numbers. The supported ranges depend upon the type of the card(4 port/8 port etc): For 4 port card : 1 - 4 For 8 port card : 1 - 8 For 2 Port Channelized card : 56 (28*2).ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.1.1.1.1 |
lineConnectorTypeThis variable indicates the connector as well as the backcard type. 1 = T1; 2 = E1. This field is set to unused(4) for FRSM-VHS cards.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.2 |
lineEnableThis variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify In FRSM-2CT3, if the DS3 line is enabled, then the DS1 channels for that line will all be automatically enabled. No independent enable/disable is allowed for each of the 28 DS1 lines in FRSM-2CT3.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.3 |
lineTypeThis variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: dsx1ESF Extended SuperFrame DS1 dsx1D4 AT&T D4 format DS1 dsx1E1 CCITT Recommendation G.704 (Table 4a) dsx1E1-CRC CCITT Recommendation G.704 (Table 4b) dsxE1-MF G.704 (Table 4a) with TS16 multiframing enabled dsx1E1-CRC-MF G.704 (Table 4b) with TS16 multiframing enabled dsx1E1clearchannel E1 clear channel, all DS0s can be used dsx1E1Q50 G.704 (table 14) In TS16 bits 5,7,8 will be set to 100 for all other cases bits 5,7,8 will have a value of 111. dsx1E1Q50CRC same as dsx1E1Q50 but with CRC. NOTE: All E1, E1-CRC, E1-MF or E1-CRC-MF are using DS0 on slot 1 for signaling and E1-MF or E1-CRC-MF use DS0 on slot 17 for synchronization. (Slot 1 and 16 is based on index 1 to 32 DS0) All DS0s can be used for any port when lineType is dsx1E1clearchannel. On a CESM card, only 'dsx1E1clearchannel' option is supported. When the lineType is dsx1E1Q50 the bits 5,7,8 of TS16 of frame zero will be forced to 100 else it will be 111. The default value for T1 is 'dsx1ESF' and for E1 is 'dsx1E1CCS'.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.4 |
lineCodingThis variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS(1): refers the Jammed Bit Zero suppression in which the AT&T specification of at least one pulse every 8 bit periods is literally implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data. dsx1B8ZS(2): refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. E1 links, with or without CRC, use dsx1HDB3 or dsx1AMI. dsx1AMI(4): refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density requirements, such as inverting HDLC data. The default value for T1 is 'dsx1JBZS' and for E1 is 'dsx1HDB3'. This field is not applicable for FRSM-VHS cards and is set to notUsed(5).rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.5 |
lineLengthThis is not a standard RFC 1407 DS1 variable, it is specific to BASIS implementation. It specifies the line length: 1 - 0 to 110 ft (T1 line only) 2 - 110 to 220 ft (T1 line only) 3 - 220 to 330 ft (T1 line only) 4 - 330 to 440 ft (T1 line only) 5 - 440 to 550 ft (T1 line only) 6 - 550 to 660 ft (T1 line only) 7 - greater than 660 ft (T1 line only) 8 - 75 ohms (E1 line only (BNC)) 9 - 120 ohms (E1 line only (DB-15)) The default value for T1 is 1, for E1, if the connector type is DB15 then the default is 9, if BNC, it's 8. For FRSM-2CT3, the line length of DS1 has no meaning as there are no physical DS1 lines. So, for this card, the value is set to notRequired (16).rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.6 |
lineXmtClockSourceThe source of Transmit Clock. loopTiming(1): indicates that the recovered receive clock is used as the transmit clock. localTiming(2): indicates that a local clock source is used.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.7 |
lineLoopbackCommandThis variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: dsx1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx1RemoteLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. dsx1LocalLoop The local data is looped back dsx1PayloadLoop This will loop only the payload and not framing/sync bit.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.8 |
lineSendCodeThis variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal data dsx1SendLineCode sending a request for a line loopback dsx1SendPayloadCode sending a request for a payload loopback dsx1SendResetCode sending a loopback termination requestrw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.9 |
lineUsedTimeslotsBitMapBit map of used DS0 for this line.ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.1.1.1.10 |
lineLoopbackCodeDetectionEnable detection of line Loopback Codesrw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.11 |
lineBERTEnableThis variable enables Bit Error Rate Testing(BERT).rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.12 |
lineBERTPatternThis variable determines BERT pattern to transmitrw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.13 |
lineBERTResultThis shows the result of the BERT.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.14 |
bERTResultClrButtonThis clears the result of the BERT.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.1.1.1.15 |
lineNumofValidEntriesThe number of DS1 configuration entries (regardless of their current configuration) in the dsx1CnfGrpTable.ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.1.2 |
dsx1AlmCnfGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.3.1.2 |
dsx1AlmCnfGrpTableThe DS1 interface alarm configuration table. SEQUENCE OF Dsx1AlmCnfGrpEntry .1.3.6.1.4.1.351.110.4.3.1.2.1 |
dsx1AlmCnfGrpEntryAn entry in the DS1 Alarm Configuration table. Dsx1AlmCnfGrpEntry .1.3.6.1.4.1.351.110.4.3.1.2.1.1 |
almCnfLineNumThis object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.1 |
redSeverityThis variable is used to setup the severity of RED alarm. So when RED alarm is detected by the card, an alarm with appropriate severity status will be sent.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.2.1.1.2 |
rAISeverityThis variable is used to setup the severity of RAI alarm. So when LOS alarm is detected the card, an alarm with appropriate severity status will be sent.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.2.1.1.3 |
nEAlarmUpCountThis parameter specifies the integration counter, the local alarms are LOS and LOF. Default value is 6 and update counter every 10 ms to reach the threshold set in threshold object. This is the up counter.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.4 |
nEAlarmDownCountThis parameter specifies the integration counter, the Near-End alarms are LOS and LOF. Default value is 1 and update counter every 10 ms to reach 0. This is the down counter.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.5 |
nEAlarmThresholdThe value set in this object determines the value to declare Near-End alarm. A count of 1500 gives 2.5 sec to declare LOS with an up count value of 6.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.6 |
fEAlarmUpCountThis parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 6 and update counter 10 ms to reach the threshold set in threshold object. This is the up counter.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.7 |
fEAlarmDownCountThis parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 1 and update counter every 10 ms to reach 0. This is the down counter.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.8 |
fEAlarmThresholdThe value set in this object determines the value to declare Far-End alarm. A count of 1500 gives 2.5 secs to declare LOS with an up count value of 6.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.9 |
statisticalAlarmSeverityThis variable is used to setup the severity of Statistical alarm. So when any statistical alarm is detected by the card, an alarm with appropriate severity status will be sent.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.2.1.1.10 |
lCV15MinThresholdCode Violation - is the occurrence of a received CRC-6 code that is not identical to the corresponding locally. calculated code. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.11 |
lCV24HrThresholdCode Violation - is the occurence of a received CRC-6 code that is not identical to the corresponding locally. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.12 |
lES15MinThresholdErrored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.13 |
lES24HrThresholdErrored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.14 |
lSES15MinThresholdSeverely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.15 |
lSES24HrThresholdSeverely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.16 |
cRC15MinThresholdThe value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.17 |
cRC24HrThresholdThe value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.18 |
cRCES15MinThresholdThe value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.19 |
cRCES24HrThresholdThe value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.20 |
cRCSES15MinThresholdThe value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.21 |
cRCSES24HrThresholdThe value set in this object determines the value when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.22 |
sEFS15MinThresholdSeverely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.23 |
sEFS24HrThresholdSeverely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.24 |
aISS15MinThresholdAlarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.25 |
aISS24HrThresholdAlarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.26 |
uAS15MinThresholdUnavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.rw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.27 |
uAS24HrThresholdUnavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour intervalrw Integer32 .1.3.6.1.4.1.351.110.4.3.1.2.1.1.28 |
dsx1AlmGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.3.1.3 |
dsx1AlmGrpTableThe DS1 interface alarm configuration table. SEQUENCE OF Dsx1AlmGrpEntry .1.3.6.1.4.1.351.110.4.3.1.3.1 |
dsx1AlmGrpEntryAn entry in the DS1 Alarm table. Each entry represents the current, 15 minute and 24 Hour bucket intervals for different performance parameters. Dsx1AlmGrpEntry .1.3.6.1.4.1.351.110.4.3.1.3.1.1 |
almLineNumThis object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.1 |
lineAlarmStateThis variable is a bitmap of the DSX1 Line Alarms. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 Receiving RAI 1 Transmitting RAI 2 Receiving AIS 3 Transmitting AIS 4 Receiving OOF 5 Receiving LOS 6 Near End Local Loopback in effect 7 Near End Remote Loopback in effect 8 Near End Remote Payload Loopback 9 Receiving CRC MF OOF (E1) 10 Receiving Sig MF OOF (E1) 11 Receiving MF RAI (E1) 12 Receiving MF AIS (E1) 13 BERT in effect 14 Far End Remote Loopback in effect 15 Detected Near End Remote Loopback in effectro Integer32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.2 |
lineStatisticalAlarmStateThis variable is a bitmap of the DSX1 Line Statistical Alarms. A value of zero indicates no alarms. Itemized below are the individual alarm bits: BitPosition Alarm ----------- ----- 0 LCV 15 minute threshold exceeded 1 LCV 24 hour threshold exceeded 2 LES 15 minute threshold exceeded 3 LES 24 hour threshold exceeded 4 LSES 15 minute threshold exceeded 5 LSES 24 hour threshold exceeded 6 CRC 15 minute threshold exceeded 7 CRC 24 hour threshold exceeded 8 CRCES 15 minute threshold exceeded 9 CRCES 24 hour threshold exceeded 10 CRCSES 15 minute threshold exceeded 11 CRCSES 24 hour threshold exceeded 12 SEFS 15 minute threshold exceeded 13 SEFS 24 hour threshold exceeded 14 AISS 15 minute threshold exceeded 15 AISS 24 hour threshold exceeded 16 UAS 15 minute threshold exceeded 17 UAS 24 hour threshold exceeded.ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.3 |
lCVCurrentThis counter counts the number of Line code violations encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.4 |
lCV15MinBucketThe counter associated with the number of Line code violations in the last 15 minute period encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.5 |
lCV24HrBucketThe counter associated with the number of Line code violations in the last 24 hour period encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.6 |
lESCurrentThis counter counts the number of Line code violations Errored Seconds encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.7 |
lES15MinBucketThis counter counts the number of Line code violations Errored Seconds in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.8 |
lES24HrBucketThis counter counts the number of Line code violations Errored Seconds in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.9 |
lSESCurrentThis counter counts the number of Line code violations Severely Errored Seconds encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.10 |
lSES15MinBucketThis counter counts the number of LCV Severely Errored Seconds in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.11 |
lSES24HrBucketThis counter counts the number of LCV Severely Errored Seconds in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.12 |
cRCCurrentThis counter counts the number of P Bit code violations encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.13 |
cRC15MinBucketThis counter counts the number of P Bit code violations in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.14 |
cRC24HrBucketThis counter counts the number of P Bit code violations in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.15 |
cRCESCurrentThis counter counts the number of PCV Errored Seconds encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.16 |
cRCES15MinBucketThis counter counts the number of PCV Errored Seconds in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.17 |
cRCES24HrBucketThis counter counts the number of PCV Errored Seconds in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.18 |
cRCSESCurrentThis counter counts the number of P Bit code violations Severely Errored Seconds encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.19 |
cRCSES15MinBucketThis counter counts the number of PCV Severely Errored Seconds in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.20 |
cRCSES24HrBucketThis counter counts the number of PCV Severely Errored Seconds in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.21 |
sEFSCurrentThis counter counts the number of Severely Errored Framing Seconds encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.22 |
sEFS15MinBucketThis counter counts the number of Severely Errored Framing Seconds in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.23 |
sEFS24HrBucketThis counter counts the number of Severely Errored Framing Seconds in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.24 |
aISSCurrentThis counter counts the number of AIS Severely Errored Seconds encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.25 |
aISS15MinBucketThis counter counts the number of AIS Severely Errored Seconds in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.26 |
aISS24HrBucketThis counter counts the number of AIS Severely Errored Seconds in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.27 |
uASCurrentThis counter counts the number of Unavailable Seconds encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.28 |
uAS15MinBucketThis counter counts the number of Unavailable Seconds in the last 15 minutes encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.29 |
uAS24HrBucketThis counter counts the number of Unavailable Seconds in the last 24 hours encountered by the interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.30 |
percentEFSThis counter counts the %LCV Error Free Seconds.ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.3.1.1.31 |
alarmClrButtonThis variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarmrw Enumeration .1.3.6.1.4.1.351.110.4.3.1.3.1.1.32 |
dsx1CntGrp OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.3.1.4 |
dsx1CntGrpTableThe DS1 Counter table. This table contains statistics since the system was up or last re-initialization. SEQUENCE OF Dsx1CntGrpEntry .1.3.6.1.4.1.351.110.4.3.1.4.1 |
dsx1CntGrpEntryAn entry in the DS1 counter table. Dsx1CntGrpEntry .1.3.6.1.4.1.351.110.4.3.1.4.1.1 |
cntLineNumThis object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.ro Integer32 .1.3.6.1.4.1.351.110.4.3.1.4.1.1.1 |
rcvLOSCountThe number of times the Loss of Signal was detected with or without integrating to LOS alarm.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.4.1.1.2 |
rcvOOFCountThe number of times the Out of Frame was detected with or without integrating to OOF alarm.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.4.1.1.3 |
rcvRAICountThe number of times Yellow Alarms was detected with or without integrating to RAI alarm.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.4.1.1.4 |
rcvFECountThe number of Framing Pattern Errors encountered by a DS1 interface.ro Counter32 .1.3.6.1.4.1.351.110.4.3.1.4.1.1.5 |
counterClearButtonThis variable is used to clear all the counters.rw Enumeration .1.3.6.1.4.1.351.110.4.3.1.4.1.1.6 |
ciscoMgx82xxDsx1MIBThe MIB module to configure DS1/E1 interface objects. This mib also contains the alarm configuration of DS1/E1 interfaces. This mib is supported in T1/E1 service modules. MODULE-IDENTITY .1.3.6.1.4.1.351.150.58 |
cmDsx1MIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.58.2 |
cmDsx1MIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.58.2.1 |
cmDsx1GeneralGroupThe collection of objects used for DS1/E1 interfaces. Unknown .1.3.6.1.4.1.351.150.58.2.1.1 |
cmDsx1ConfGroupThe collection of objects used for DS1/E1 interface configuration. Unknown .1.3.6.1.4.1.351.150.58.2.1.2 |
cmDsx1CountGroupThe collection of objects related to DS1/E1 statistics. Unknown .1.3.6.1.4.1.351.150.58.2.1.3 |
cmDsx1AlarmConfGroupThe collection of objects used for DS1/E1 Alarm threshold configuration. Unknown .1.3.6.1.4.1.351.150.58.2.1.4 |
cmDsx1AlarmGroupThe collection of objects used for DS1/E1 Alarm configuration. Unknown .1.3.6.1.4.1.351.150.58.2.1.5 |
cmDsx1MIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.58.2.2 |
cmDsx1ComplianceThe compliance statement for objects related to DS1/E1 mib. Unknown .1.3.6.1.4.1.351.150.58.2.2.1 |