CHIPAGENT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CHIPAGENT-MIB.
111
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
111 total| Object Name |
|---|
chipcom OBJECT IDENTIFIER .1.3.6.1.4.1.49 |
RFC1155-SMI Unknown .1.3.6.1.4.1.49 |
chipmib02 OBJECT IDENTIFIER .1.3.6.1.4.1.49.2 |
chipGen OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.1 |
chipGenProductThe product type represented by this agent.ro Enumeration .1.3.6.1.4.1.49.2.1.1 |
chipGenServiceDateThe date that the product was last serviced in the
format yymmdd. If this date is unknown, the value of this
object is '000000'.ro DisplayString .1.3.6.1.4.1.49.2.1.2 |
chipGenNetmanThe IP (source) Address of the last authenticated SNMP PDU
received by this entity before this request. An IP Address
of 00.00.00.00 represents the default value.ro IpAddress .1.3.6.1.4.1.49.2.1.3 |
chipGenDiagnosticsThe result of this product's diagnostic test(s). If
any test fails, this will have the failed(2) value.
Note, many products do not operate after a diagnostic
failure. In this case, no SNMP communication would
be available.ro Enumeration .1.3.6.1.4.1.49.2.1.4 |
chipGenSerialThe serial number of this product.ro DisplayString .1.3.6.1.4.1.49.2.1.5 |
chipGenIDA unique ID used for grouping disparate agents together.
For example, a concentrator may contain multiple agents.
This ID is could be assigned by the management station
to identify all of these agents as being contained in the
same concentrator.rw INTEGER .1.3.6.1.4.1.49.2.1.6 |
chipGenVersThe version identifier(s) for this agent.ro DisplayString .1.3.6.1.4.1.49.2.1.7 |
chipGenAuthFailureAddrThe source IP Address of the last SNMP request that caused
an authentication failure trap to be generated. This
object is also included in the SNMP authenticationFailure
trap.ro IpAddress .1.3.6.1.4.1.49.2.1.8 |
chipGenTimeLastChangedA snapshot of sysUpTime when the last trap was generated.
This attribute can be used to save polling by a management
station. If there have been no traps generated since the last
poll, there is no need for the station to poll again.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.49.2.1.9 |
chipEcho OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.2 |
chipEchoStartSetting chipEchoStart to startEcho(2) causes the device
to begin an ICMP echo sequence using the parameters
indicated by the rest of the chipEcho group.rw Enumeration .1.3.6.1.4.1.49.2.2.1 |
chipEchoAddrThe IP Address to which the device will ping. The default
value is the loopback address 127.0.0.1 .rw IpAddress .1.3.6.1.4.1.49.2.2.2 |
chipEchoPatternThe actual pattern to be contained in the ICMP echo packet.rw Enumeration .1.3.6.1.4.1.49.2.2.3 |
chipEchoNumberThe number of ICMP echo packets (pings) to send.rw INTEGER .1.3.6.1.4.1.49.2.2.4 |
chipEchoSizeThe size of the ICMP echo packet (ping) to send when
chipEchoStart is set. The valid range is between 64 and
1500 octets.rw INTEGER .1.3.6.1.4.1.49.2.2.5 |
chipEchoResponseCountsThe count of ICMP echo response packets received since
the last PING was initiated.ro Counter .1.3.6.1.4.1.49.2.2.6 |
chipProducts OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3 |
online OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1 |
olAgents OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.1 |
olConc OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.2 |
olEnv OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.3 |
olModules OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4 |
olSpecMods OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4 |
ol50nnMCTL OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.3 |
ol51nnMMGT OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.4 |
ol51nnMFIB OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.5 |
ol51nnMUTP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.6 |
ol51nnMTP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.7 |
ol51nnMBNC OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.8 |
ol51nnBEE OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.9 |
ol51nnRES OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.10 |
ol51nnREE OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.11 |
ol51nnMAUIF OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.12 |
ol51nnMAUIM OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.13 |
ol5208MTP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.14 |
ol51nnMFP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.15 |
ol51nnMFBP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.16 |
ol51nnMTPL OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.17 |
ol51nnMTPPL OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.18 |
ol52nnMTP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.19 |
ol52nnMFR OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.20 |
ol51nnMTS OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.21 |
ol51nnMFL OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.22 |
ol50nnMRCTL OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.23 |
ol51nnMFB OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.24 |
ol53nnMMGT OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.25 |
ol53nnMFBMIC OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.26 |
ol53nnMFIBST OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.27 |
ol53nnMSTP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.28 |
ol51nnMTPCL OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.29 |
ol52nnBTT OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.30 |
ol51nnIx OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.31 |
ol52nnMMGT OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.32 |
ol50nnMHCTL OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.4.4.33 |
olNets OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.5 |
olNet OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.5.1 |
olEnet OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.5.2 |
olTRnet OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.5.3 |
olFDDInet OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.5.4 |
olGroups OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.6 |
olAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.7 |
olThresh OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.7.1 |
olThreshControl OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.1.7.1.1 |
oebm OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.2 |
midnight OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.3 |
workGroupHub OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4 |
hubSysGroup OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4.1 |
hardwareGroup OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4.2 |
softwareGroup OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4.3 |
hubGroup OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4.4 |
boardGroup OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4.5 |
portGroup OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4.6 |
alarmGroup OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.4.7 |
emm OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.5 |
chipBridge OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.6 |
trmm OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.7 |
fmm OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.8 |
focus1 OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.9 |
oeim OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.3.10 |
chipExperiment OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.4 |
chipExpTokenRing OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.4.1 |
dot5 OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.4.1.1 |
dot1dBridge OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.4.14 |
chipTTY OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.5 |
chipTTYNumberThe number of terminal ports on this agent product.ro INTEGER .1.3.6.1.4.1.49.2.5.1 |
chipTTYTableA table of TTY specific information associated with
this agent. SEQUENCE OF ChipTTYEntry .1.3.6.1.4.1.49.2.5.2 |
chipTTYEntryA profile of a specific TTY interface associated with
this agent. ChipTTYEntry .1.3.6.1.4.1.49.2.5.2.1 |
chipTTYIndexThe TTY to which this entry refers.ro INTEGER .1.3.6.1.4.1.49.2.5.2.1.1 |
chipTTYBaudThe baud rate for this TTY. It should be noted that all
serial ports do not support all of the above baud rates.rw Enumeration .1.3.6.1.4.1.49.2.5.2.1.2 |
chipTTYParityThe parity setting for this TTY.rw Enumeration .1.3.6.1.4.1.49.2.5.2.1.3 |
chipTTYStopThe number of stop bits for this TTY.rw Enumeration .1.3.6.1.4.1.49.2.5.2.1.4 |
chipTTYDataThe number of data bits for this TTY.rw Enumeration .1.3.6.1.4.1.49.2.5.2.1.5 |
chipTTYTimeoutThe number of minutes to wait before this agent logs out
an inactive login session on this TTY.
NOTE: In some implementations, this is a single variable
that is used by all of the terminal and telnet
sessions.rw INTEGER .1.3.6.1.4.1.49.2.5.2.1.6 |
chipTTYPromptThe terminal prompt to display on this TTY.
NOTE: In some implementations, this is a single variable
that is used by all of the terminal and telnet
sessions.rw DisplayString .1.3.6.1.4.1.49.2.5.2.1.7 |
chipTTYDTRThis value dictates the behavior of the RS-232 Data
Terminal Ready (DTR) signal at the time a session ends
due to a logout, timeout, or shutdown. This is used by
some modems as an indication that they should hangup.
This variable is only support if the RS-232 port has a
DTR signal.rw Enumeration .1.3.6.1.4.1.49.2.5.2.1.8 |
chipTTYTerminalTypeA string which indicates the type of terminal that
is attached to the serial port. It should be noted that
the string is passed to a telnet server whenever the server
issues the IAC DO TERMINAL-TYPE command (see rfc884).rw DisplayString .1.3.6.1.4.1.49.2.5.2.1.9 |
chipTFTP OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.6 |
chipTFTPStartSetting chipTFTPStart to tftpGet(2) initiates a file
transfer to the agent (download); tftpPut(3) initiates
a file transfer to the server (upload).rw Enumeration .1.3.6.1.4.1.49.2.6.1 |
chipTFTPSlotThe slot number of the module that is to be involved
in the TFTP transfer with the TFTP server (chipTFTPIpAddress).rw Enumeration .1.3.6.1.4.1.49.2.6.2 |
chipTFTPIpAddressThe IP Address of the TFTP server.rw IpAddress .1.3.6.1.4.1.49.2.6.3 |
chipTFTPFileNameThe file name of the file to retrieve (tftpGet), or the
name of the file to create (tftpPut).rw DisplayString .1.3.6.1.4.1.49.2.6.4 |
chipTFTPFileTypeThe type of file image to upload/download. The file
type indicates to the agent what kind of file it is
receiving. flashCode(1) indicates a code upgrade of
the operational proms. bootCode(2) indicates a code
upgrade of the boot proms.rw Enumeration .1.3.6.1.4.1.49.2.6.5 |
chipTFTPResultThe result of the last TFTP operation.ro Enumeration .1.3.6.1.4.1.49.2.6.6 |
chipDownload OBJECT IDENTIFIER .1.3.6.1.4.1.49.2.7 |
chipDownloadUDKSerialA string representing the serial number of the
Upgrade Distribution Kit.rw DisplayString .1.3.6.1.4.1.49.2.7.1 |
chipDownloadKeyThe key code provided by your VAR. Available by
calling technical support at +1 508 460 6195.rw DisplayString .1.3.6.1.4.1.49.2.7.2 |
chipDownloadDateTimeThe date of the last successful download in the
format hh:mm day DD Mon YYro DisplayString .1.3.6.1.4.1.49.2.7.3 |
CHIPAGENT-MIB Technical Reference Overview
The CHIPAGENT-MIB SNMP MIB module published by Chipcom defines 111 managed OID objects, including 35 scalar/column metrics, 1 SNMP tables, and 0 trap/notification events. Key tabular structures include chipTTYTable.
Key OID Definitions in CHIPAGENT-MIB
chipTTYTable
.1.3.6.1.4.1.49.2.5.2A table of TTY specific information associated with this agent.
chipGenProduct
.1.3.6.1.4.1.49.2.1.1The product type represented by this agent.
chipGenServiceDate
.1.3.6.1.4.1.49.2.1.2The date that the product was last serviced in the format yymmdd. If this date is unknown, the value of this object is '000000'.
chipGenNetman
.1.3.6.1.4.1.49.2.1.3The IP (source) Address of the last authenticated SNMP PDU received by this entity before this request. An IP Address of 00.00.00.00 represents the default value.
chipGenDiagnostics
.1.3.6.1.4.1.49.2.1.4The result of this product's diagnostic test(s). If any test fails, this will have the failed(2) value. Note, many products do not operate after a diagnostic failure. In this case, no SNMP communication would be available.
chipGenSerial
.1.3.6.1.4.1.49.2.1.5The serial number of this product.
chipGenID
.1.3.6.1.4.1.49.2.1.6A unique ID used for grouping disparate agents together. For example, a concentrator may contain multiple agents. This ID is could be assigned by the management station to identify all of these agents as being contained in the same concentrator.
chipGenVers
.1.3.6.1.4.1.49.2.1.7The version identifier(s) for this agent.
chipGenAuthFailureAddr
.1.3.6.1.4.1.49.2.1.8The source IP Address of the last SNMP request that caused an authentication failure trap to be generated. This object is also included in the SNMP authenticationFailure trap.
chipGenTimeLastChanged
.1.3.6.1.4.1.49.2.1.9A snapshot of sysUpTime when the last trap was generated. This attribute can be used to save polling by a management station. If there have been no traps generated since the last poll, there is no need for the station to poll again.
chipEchoStart
.1.3.6.1.4.1.49.2.2.1Setting chipEchoStart to startEcho(2) causes the device to begin an ICMP echo sequence using the parameters indicated by the rest of the chipEcho group.
chipEchoAddr
.1.3.6.1.4.1.49.2.2.2The IP Address to which the device will ping. The default value is the loopback address 127.0.0.1 .
More MIBs from Chipcom
Browse all ChipcomMIBs →CHIPCOMMIB
Standard SNMP MIB module defining data structures for CHIPCOMMIB.
1416 objects→
CHIPCOM-MIB
Standard SNMP MIB module defining data structures for CHIPCOM-MIB.
965 objects→
CHIPMODULE-MIB
Standard SNMP MIB module defining data structures for CHIPMODULE-MIB.
586 objects→
CHIPTRNET-MIB
SNMP MIB module
218 objects→
CHIPCONC-MIB
Standard SNMP MIB module defining data structures for CHIPCONC-MIB.
177 objects→
CHIPDOT1D-MIB
Standard SNMP MIB module defining data structures for CHIPDOT1D-MIB.
127 objects→