CERAGON-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CERAGON-MIB.
1503
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
1503 total| Object Name |
|---|
ceragon OBJECT IDENTIFIER .1.3.6.1.4.1.2281 |
RFC1213-MIB Unknown .1.3.6.1.4.1.2281 |
gnODUTrapThe trap is sent every time an alarm occurs in the ODU. TRAP-TYPE .1.3.6.1.4.1.2281.0.1 |
gnIDUTrapThe trap is sent every time an alarm occurs in the IDU. TRAP-TYPE .1.3.6.1.4.1.2281.0.2 |
gnSDHTrapThe trap is sent every time an alarm occurs in the Regenerator section
in
the SONET/SDH. TRAP-TYPE .1.3.6.1.4.1.2281.0.3 |
gnACCESSTrapThe trap is sent every time an alarm occurs in an Access line. TRAP-TYPE .1.3.6.1.4.1.2281.0.4 |
gnODUTrapClearedThe trap is sent every time an alarm occurs in the ODU. TRAP-TYPE .1.3.6.1.4.1.2281.0.5 |
gnIDUTrapClearedThe trap is sent every time an alarm occurs in the IDU. TRAP-TYPE .1.3.6.1.4.1.2281.0.6 |
gnSDHTrapClearedThe trap is sent every time an alarm occurs in the Regenerator section in
the SONET/SDH. TRAP-TYPE .1.3.6.1.4.1.2281.0.7 |
gnAccessTrapClearedThe trap is sent every time an alarm occurs in an Access line. TRAP-TYPE .1.3.6.1.4.1.2281.0.8 |
gnLODUPowerFailTrapThis Trap is sent every time a Local ODU Power fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.10 |
gnLODUSynthUnLockTrapThis Trap is sent every time a Local ODU Hardware fault occurs . TRAP-TYPE .1.3.6.1.4.1.2281.0.11 |
gnLODUTxLevelOutOfRangeTrapThis Trap is sent every time a Local ODU TX signal is out of range. TRAP-TYPE .1.3.6.1.4.1.2281.0.12 |
gnLODURxLevelOutOfRangeTrapThis Trap is sent every time a Local ODU RX signal is out of range. TRAP-TYPE .1.3.6.1.4.1.2281.0.13 |
gnLODUExtremeTempTrapThis Trap is sent every time a Local ODU extreme temperature event occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.14 |
gnLIDUPowerFailTrapThis Trap is sent every time a Local IDU Power fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.15 |
gnLCableFaultTrapThis Trap is sent every time a Local IDU-ODU cable fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.16 |
gnLModemFailTrapThis Trap is sent every time a Local Modem faults occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.17 |
gnLIDUExtremeTempTrapThis Trap is sent every time a Local IDU extreme temperature event occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.18 |
gnLLoopbackOnTrapThis Trap is sent every time a Local Loopback is activated. TRAP-TYPE .1.3.6.1.4.1.2281.0.19 |
gnLRemoteCommFaultTrapThis Trap is sent every time the remote communication is disconnected. TRAP-TYPE .1.3.6.1.4.1.2281.0.20 |
gnLTestRunningTrapThis Trap is sent every time a Local SDH/SONET test is activated. TRAP-TYPE .1.3.6.1.4.1.2281.0.21 |
gnLLOFTrapThis Trap is sent every time a Local Loss of Frame alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.22 |
gnLLOSTrapThis Trap is sent every time a Local Loss of signal alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.23 |
gnLTIMTrapThis Trap is sent every time a Local Trace Identifier Mismatch alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.24 |
gnLEXCTrapThis Trap is sent every time a Local Excessive BER alarm is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.25 |
gnLSDTrapThis Trap is sent every time a Local Signal Degrade alarm is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.26 |
gnLRcvAisTrapThis Trap is sent every time the local terminal receives an Alarm Indication Signal (AIS). TRAP-TYPE .1.3.6.1.4.1.2281.0.27 |
gnLUnExpTrapThis Trap is sent every time a Local terminal receives an unexpected signal. TRAP-TYPE .1.3.6.1.4.1.2281.0.28 |
gnLLocTrapThis Trap is sent every time a Local Loss of Clock alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.29 |
gnLLopTrapThis Trap is sent every time a Local Loss of pointer alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.30 |
gnLRdiTrapThis Trap is sent every time the local terminal receives a Remote Defect Identifier signal (RDI). TRAP-TYPE .1.3.6.1.4.1.2281.0.31 |
gnLSlmTrapThis Trap is sent every time a Local Signal (Payload) Label Mismatch alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.32 |
gnLUnqTrapThis Trap is sent every time a Local unequipped signal is received. TRAP-TYPE .1.3.6.1.4.1.2281.0.33 |
gnLExternalAlarm1OnTrapThis Trap is sent every time a Local External alarm 1 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.34 |
gnLExternalAlarm2OnTrapThis Trap is sent every time a Local External alarm 2 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.35 |
gnLExternalAlarm3OnTrapThis Trap is sent every time a Local External alarm 3 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.36 |
gnLExternalAlarm4OnTrapThis Trap is sent every time a Local External alarm 4 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.37 |
gnLExternalAlarm5OnTrapThis Trap is sent every time a Local External alarm 5 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.38 |
gnLExternalAlarm6OnTrapThis Trap is sent every time a Local External alarm 6 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.39 |
gnLExternalAlarm7OnTrapThis Trap is sent every time a Local External alarm 7 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.40 |
gnLExternalAlarm8OnTrapThis Trap is sent every time a Local External alarm 8 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.41 |
gnLSystemFaultTrapThis Trap is sent every time a Local System fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.42 |
gnLTftpFaultTrapThis Trap is sent every time a Local TFTP Download fails. TRAP-TYPE .1.3.6.1.4.1.2281.0.43 |
gnLInternalDownloadFaultTrapThis Trap is sent every time a Local internal Download fails. TRAP-TYPE .1.3.6.1.4.1.2281.0.44 |
gnLIntralinkFaultTrapThis Trap is sent every time a Local intra-link download fails. TRAP-TYPE .1.3.6.1.4.1.2281.0.45 |
gnLConfMismatchTrapThis Trap is sent every time a Local configuration mismatch fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.46 |
gnLProtectSwitchFaultTrapThis Trap is sent every time a Local Protection fault is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.47 |
gnLProtectCableFaultTrapThis Trap is sent every time a Local protection cable fault is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.48 |
gnLHeartBeatTrapThis Trap is a periodic heart beat trap. TRAP-TYPE .1.3.6.1.4.1.2281.0.49 |
gnLLomTrapThis Trap is sent every time a Local Loss of Multi-frame alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.50 |
gnLHitlessProblemTrapThis Trap is sent every time a Local Hitless fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.51 |
gnLHitlessRadioLofTrapThis Trap is sent every time a Local Hitless RadioLOF fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.52 |
gnLHitlessCableDisconnectTrapThis Trap is sent every time a Local Hitless cable fault is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.53 |
gnLPamTrapThis Trap is sent when system in MSP Protection Architecture Mismatch. TRAP-TYPE .1.3.6.1.4.1.2281.0.54 |
gnLScmTrapThis Trap is sent when there is a MSP Selector Channel Mismatch (K1,K2). TRAP-TYPE .1.3.6.1.4.1.2281.0.55 |
gnLInvTrapThis Trap indicates that the received K1 byte is invalid (MSP). TRAP-TYPE .1.3.6.1.4.1.2281.0.56 |
gnLInbandTrapThis Trap is sent when the Inband PPP link goes down. TRAP-TYPE .1.3.6.1.4.1.2281.0.57 |
gnWSLOSTrapThis Trap is sent when the Wayside channel is in LOS state. TRAP-TYPE .1.3.6.1.4.1.2281.0.58 |
gnODUtoODUCableFaultTrapThis Trap is sent when there is a problem with the ODU to ODU cable - for XPIC topology only. TRAP-TYPE .1.3.6.1.4.1.2281.0.59 |
gnNoSignalReceivedFromODUTrapThis Trap is sent when no signal is received from the ODU. TRAP-TYPE .1.3.6.1.4.1.2281.0.60 |
gnProtectionLockoutConfiguredTrapThis Trap is sent when Protection lockout is configured. TRAP-TYPE .1.3.6.1.4.1.2281.0.61 |
gnRFUPowerFailureTrapThis Trap is sent in case of 12V/-5V/1.5V/6V/Vdrain power supply failure . TRAP-TYPE .1.3.6.1.4.1.2281.0.62 |
gnRFURxLevelPathOutOfRangeTrapThis Trap is sent in case of RSL of Main/Diversity channel is very low(typically below -80dBm) . TRAP-TYPE .1.3.6.1.4.1.2281.0.63 |
gnRFUExtremeTemperatureTrapThis Trap is sent in case of RFU temperature is too high/low . TRAP-TYPE .1.3.6.1.4.1.2281.0.64 |
gnRFUFanFailureTrapThis Trap is sent in case of fan failure detection by RFU . TRAP-TYPE .1.3.6.1.4.1.2281.0.65 |
gnLowSignalToRFUTrapThis Trap is sent in case of low IDM signal reception (350MHz) . TRAP-TYPE .1.3.6.1.4.1.2281.0.66 |
gnRFUXPICClockFailureTrapThis Trap is sent in case of XPIC clock failure . TRAP-TYPE .1.3.6.1.4.1.2281.0.67 |
gnRFUDelayCalibrationFailure1TrapThis Trap is sent if RX AGC is not locked (-10dBm) . TRAP-TYPE .1.3.6.1.4.1.2281.0.68 |
gnRFUDelayCalibrationFailure2TrapThis Trap is sent if calibration cannot be done since the notch is too wide/deep . TRAP-TYPE .1.3.6.1.4.1.2281.0.69 |
gnLSFPFaultTrapThis Trap is sent every time a Gigabit ethernet SFP fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.70 |
gnEncryptionFaultTrapThis Trap is sent every time a Encryption fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.71 |
gnEncryptionSyncLosTrapThis Trap is sent every time a Encryption synchhronization loss occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.72 |
gnEncryptionKepTimoutThis Trap is sent every time a Encryption KEP Timout fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.73 |
gnEncryptionSkTimerElapsedThis Trap is sent every time a Encryption Session Key Timer elapsed. TRAP-TYPE .1.3.6.1.4.1.2281.0.74 |
gnEncryptionPowerUpSelfTestFailThis Trap is sent every time a Encryption Power Up Self Test fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.75 |
gnEncryptionConditionalTestFailThis Trap is sent every time a Encryption Conditional Test fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.76 |
gnEncryptionWillTurnOffOnNextRestThis Trap is sent every time a Encryption will be turned off on the next reset occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.77 |
gnEncryptionEventReportThis Trap is sent every time a Encryption event report occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.78 |
gnEncryptionTechCardWasDetectedThis Trap is sent every time Encryption Technician card is detected. TRAP-TYPE .1.3.6.1.4.1.2281.0.79 |
gnAdminPasswordInDefaultStateThis Trap is sent every time a admin password is in default state. TRAP-TYPE .1.3.6.1.4.1.2281.0.80 |
gnLinkGroupingProtectionFaultTrapThis Trap is sent in case of Link Grouping Protection Fault. TRAP-TYPE .1.3.6.1.4.1.2281.0.81 |
gnLossOfProtectionTrapThis Trap is sent in case of Loss of Protection. TRAP-TYPE .1.3.6.1.4.1.2281.0.82 |
gnTempLicenseTrapThis Trap is sent in case of Temp License is Enable. TRAP-TYPE .1.3.6.1.4.1.2281.0.83 |
gnMUXCfgXTempLicenseTrapThis Trap is sent in case of Temp License is Enable. TRAP-TYPE .1.3.6.1.4.1.2281.0.84 |
gnLODUPowerOkTrapThis Trap is sent every time a Local ODU Power fault cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.110 |
gnLODUSynthLockTrapThis Trap is sent every time a Local ODU Hardware fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.111 |
gnLODUTxLevelInRangeTrapThis Trap is sent every time a Local ODU TX signal is in range. TRAP-TYPE .1.3.6.1.4.1.2281.0.112 |
gnLODURxLevelInRangeTrapThis Trap is sent every time a Local ODU RX signal is in range. TRAP-TYPE .1.3.6.1.4.1.2281.0.113 |
gnLODUNormalTempTrapThis Trap is sent every time a Local ODU returns to normal temperature. TRAP-TYPE .1.3.6.1.4.1.2281.0.114 |
gnLIDUPowerOkTrapThis Trap is sent every time a Local IDU Power fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.115 |
gnLCableOkTrapThis Trap is sent every time a Local IDU-ODU cable fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.116 |
gnLModemOkTrapThis Trap is sent every time a Local Modem faults is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.117 |
gnLIDUNormalTempTrapThis Trap is sent every time a Local IDU returns to normal temperature. TRAP-TYPE .1.3.6.1.4.1.2281.0.118 |
gnLLoopbackOffTrapThis Trap is sent every time a Local Loopback is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.119 |
gnLRemoteCommOkTrapThis Trap is sent every time the remote communication is re-connected. TRAP-TYPE .1.3.6.1.4.1.2281.0.120 |
gnLNoTestRunningTrapThis Trap is sent every time a Local SDH/SONET test is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.121 |
gnLNoLOFTrapThis Trap is sent every time a Local Loss of Frame alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.122 |
gnLNoLOSTrapThis Trap is sent every time a Local Loss of Signal alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.123 |
gnLNoTIMTrapThis Trap is sent every time a Local Trace Identifier Mismatch alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.124 |
gnLNoEXCTrapThis Trap is sent every time a Local Excessive BER alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.125 |
gnLNoSDTrapThis Trap is sent every time a Local Signal Degrade alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.126 |
gnLNoAisTrapThis Trap is sent every time the local terminal stops receiving an Alarm Indication Signal (AIS). TRAP-TYPE .1.3.6.1.4.1.2281.0.127 |
gnLNoUnExpTrapThis Trap is sent every time a Local terminal stops receiving an unexpected signal. TRAP-TYPE .1.3.6.1.4.1.2281.0.128 |
gnLNoLocTrapThis Trap is sent every time a Local Loss of Carrier (On the FE interfaces) alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.129 |
gnLNoLopTrapThis Trap is sent every time a Local Loss of pointer alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.130 |
gnLNoRdiTrapThis Trap is sent every time the local terminal stops receiving a Remote Defect Identifier signal (RDI). TRAP-TYPE .1.3.6.1.4.1.2281.0.131 |
gnLNoSlmTrapThis Trap is sent every time a Local Signal (Payload) Label Mismatch alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.132 |
gnLNoUnqTrapThis Trap is sent every time a Local terminal start receiving an equipped signal. TRAP-TYPE .1.3.6.1.4.1.2281.0.133 |
gnLExternalAlarm1OffTrapThis Trap is sent every time a Local External alarm 1 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.134 |
gnLExternalAlarm2OffTrapThis Trap is sent every time a Local External alarm 2 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.135 |
gnLExternalAlarm3OffTrapThis Trap is sent every time a Local External alarm 3 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.136 |
gnLExternalAlarm4OffTrapThis Trap is sent every time a Local External alarm 4 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.137 |
gnLExternalAlarm5OffTrapThis Trap is sent every time a Local External alarm 5 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.138 |
gnLExternalAlarm6OffTrapThis Trap is sent every time a Local External alarm 6 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.139 |
gnLExternalAlarm7OffTrapThis Trap is sent every time a Local External alarm 7 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.140 |
gnLExternalAlarm8OffTrapThis Trap is sent every time a Local External alarm 8 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.141 |
gnLSystemOkTrapThis Trap is sent every time a Local System fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.142 |
gnLTftpOkTrapThis Trap is sent every time a Local TFTP Download succeeded. TRAP-TYPE .1.3.6.1.4.1.2281.0.143 |
gnLInternalDownloadOkTrapThis Trap is sent every time a Local internal Download succeeded. TRAP-TYPE .1.3.6.1.4.1.2281.0.144 |
gnLIntralinkOkTrapThis Trap is sent every time a Local intra-link download succeeded. TRAP-TYPE .1.3.6.1.4.1.2281.0.145 |
gnLNoConfMismatchTrapThis Trap is sent every time a Local configuration mismatch fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.146 |
gnLProtectSwitchOkTrapNever sent. TRAP-TYPE .1.3.6.1.4.1.2281.0.147 |
gnLProtectCableOkTrapThis Trap is sent every time a Local protection cable fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.148 |
gnLLomOkTrapThis Trap is sent every time a Local Loss of Multi-frame alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.150 |
gnLHitlessProblemOKTrapThis Trap is sent every time a Local Hitless fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.151 |
gnLHitlessRadioLofOKTrapThis Trap is sent every time a Local Hitless RadioLOF fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.152 |
gnLHitlessCableDisconnectOKTrapThis Trap is sent every time a Local Hitless cable fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.153 |
gnLPamOkTrapThis Trap is sent when system in MSP Protection Architecture Mismatch. TRAP-TYPE .1.3.6.1.4.1.2281.0.154 |
gnLScmOkTrapThis Trap is sent when there is a MSP Selector Channel Mismatch (K1,K2). TRAP-TYPE .1.3.6.1.4.1.2281.0.155 |
gnLInvOkTrapThis Trap indicates that the received K1 byte is invalid (MSP). TRAP-TYPE .1.3.6.1.4.1.2281.0.156 |
gnLInbandOkTrapThis Trap is sent when the Inband PPP link goes up. TRAP-TYPE .1.3.6.1.4.1.2281.0.157 |
gnWSNoLOSTrapThis Trap is sent when the Wayside channel is in LOS state. TRAP-TYPE .1.3.6.1.4.1.2281.0.158 |
gnODUtoODUCableOkTrapThis Trap is sent when there is a problem with the ODU to ODU cable - for XPIC topology only. TRAP-TYPE .1.3.6.1.4.1.2281.0.159 |
gnSignalReceivedFromODUTrapThis Trap is sent when a signal is received from the ODU. TRAP-TYPE .1.3.6.1.4.1.2281.0.160 |
gnProtectionLockoutClearededTrapThis Trap is sent when Protection lockout is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.161 |
gnRFUPowerFailureClearedTrapThis Trap is sent in case of 12V/-5V/1.5V/6V/Vdrain power supply failure is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.162 |
gnRFURxLevelPathOutOfRangeClearedTrapThis Trap is sent in case of RSL of Main/Diversity channel is not very low . TRAP-TYPE .1.3.6.1.4.1.2281.0.163 |
gnRFUExtremeTemperatureClearedTrapThis Trap is sent in case of RFU temperature is not too high/low . TRAP-TYPE .1.3.6.1.4.1.2281.0.164 |
gnRFUFanFailureClearedTrapThis Trap is sent when fan failure is cleared . TRAP-TYPE .1.3.6.1.4.1.2281.0.165 |
gnLowSignalToRFUClearedTrapThis Trap is sent in case of not low IDM signal reception . TRAP-TYPE .1.3.6.1.4.1.2281.0.166 |
gnRFUXPICClockFailureClearedTrapThis Trap is sent in case of XPIC clock failure is cleared . TRAP-TYPE .1.3.6.1.4.1.2281.0.167 |
gnRFUDelayCalibrationFailure1ClearedTrapThis Trap is sent if RX AGC is locked . TRAP-TYPE .1.3.6.1.4.1.2281.0.168 |
gnRFUDelayCalibrationFailure2ClearedTrapThis Trap is sent if calibration can be done . TRAP-TYPE .1.3.6.1.4.1.2281.0.169 |
gnLSFPOkTrapThis Trap is sent every time a Gigabit ethernet SFP fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.170 |
gnEncryptionFaultClearedTrapThis Trap is sent every time a Encryption fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.171 |
gnEncryptionSyncLosClearedTrapThis Trap is sent every time a Encryption synchronization loss fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.172 |
gnEncryptionKepTimoutClearedThis Trap is sent every time a Encryption KEP timout fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.173 |
gnEncryptionSkTimerElapsedClearedThis Trap is sent every time a encryption Encryption Session Key Timer elapsed fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.174 |
gnEncryptionPowerUpSelfTestFailClearedThis Trap is sent every time a Encryption Power Up Self Test fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.175 |
gnEncryptionConditionalTestFailClearedThis Trap is sent every time a Encryption Conditional Test fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.176 |
gnEncryptionWillTurnOffOnNextRestClearedThis Trap is sent every time a Encryption will be turned off on the next reset clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.177 |
gnEncryptionEventReportClearedThis Trap is sent every time a Encryption event report fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.178 |
gnEncryptionTechCardWasDetectedClearedThis Trap is sent every time a Encryption Technician card is detected clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.179 |
gnAdminPasswordInDefaultStateClearedThis Trap is sent every time a admin password is in default state clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.180 |
gnLinkGroupingProtectionFaultClearedTrapThis Trap is sent in case the Link Grouping Protection Fault clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.181 |
gnLossOfProtectionClearedTrapThis Trap is sent in case the Loss of Protection clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.182 |
gnTempLicenseClearedTrapThis Trap is sent in case the Temp License Enable clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.183 |
gnMUXCfgXTempLicenseClearedTrapThis Trap is sent in case the Temp License Enable clears. TRAP-TYPE .1.3.6.1.4.1.2281.0.184 |
gnRODUPowerFailTrapThis Trap is sent every time a Remote ODU Power fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.210 |
gnRODUSynthUnLockTrapThis Trap is sent every time a Remote ODU Hardware fault occurs . TRAP-TYPE .1.3.6.1.4.1.2281.0.211 |
gnRODUTxLevelOutOfRangeTrapThis Trap is sent every time a Remote ODU TX signal is out of range. TRAP-TYPE .1.3.6.1.4.1.2281.0.212 |
gnRODURxLevelOutOfRangeTrapThis Trap is sent every time a Remote ODU RX signal is out of range. TRAP-TYPE .1.3.6.1.4.1.2281.0.213 |
gnRODUExtremeTempTrapThis Trap is sent every time a Remote ODU extreme temperature event occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.214 |
gnRIDUPowerFailTrapThis Trap is sent every time a Remote IDU Power fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.215 |
gnRCableFaultTrapThis Trap is sent every time a Remote IDU-ODU cable fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.216 |
gnRModemFailTrapThis Trap is sent every time a Remote Modem faults occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.217 |
gnRIDUExtremeTempTrapThis Trap is sent every time a Remote IDU extreme temperature event occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.218 |
gnRLoopbackOnTrapThis Trap is sent every time a Remote Loopback is activated. TRAP-TYPE .1.3.6.1.4.1.2281.0.219 |
gnRRemoteCommFaultTrapThis Trap is sent every time the remote communication is disconnected. TRAP-TYPE .1.3.6.1.4.1.2281.0.220 |
gnRTestRunningTrapThis Trap is sent every time a Remote SDH/SONET test is activated. TRAP-TYPE .1.3.6.1.4.1.2281.0.221 |
gnRLOFTrapThis Trap is sent every time a Remote Loss of Frame alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.222 |
gnRLOSTrapThis Trap is sent every time a Remote Loss of signal alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.223 |
gnRTIMTrapThis Trap is sent every time a Remote Trace Identifier Mismatch alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.224 |
gnREXCTrapThis Trap is sent every time a Remote Excessive BER alarm is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.225 |
gnRSDTrapThis Trap is sent every time a Remote Signal Degrade alarm is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.226 |
gnRAisTrapThis Trap is sent every time the Remote terminal receives an Alarm Indication Signal (AIS). TRAP-TYPE .1.3.6.1.4.1.2281.0.227 |
gnRUnExpTrapThis Trap is sent every time a Remote terminal receives an unexpected signal. TRAP-TYPE .1.3.6.1.4.1.2281.0.228 |
gnRLocTrapThis Trap is sent every time a Remote Loss of Carrier (On the FE interfaces) alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.229 |
gnRLopTrapThis Trap is sent every time a Remote Loss of pointer alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.230 |
gnRRdiTrapThis Trap is sent every time the Remote terminal receives a Remote Defect Identifier signal (RDI). TRAP-TYPE .1.3.6.1.4.1.2281.0.231 |
gnRSlmTrapThis Trap is sent every time a Remote Signal (Payload) Label Mismatch alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.232 |
gnRUnqTrapThis Trap is sent every time a Remote unequipped signal is received. TRAP-TYPE .1.3.6.1.4.1.2281.0.233 |
gnRExternalAlarm1OnTrapThis Trap is sent every time a Remote External alarm 1 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.234 |
gnRExternalAlarm2OnTrapThis Trap is sent every time a Remote External alarm 2 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.235 |
gnRExternalAlarm3OnTrapThis Trap is sent every time a Remote External alarm 3 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.236 |
gnRExternalAlarm4OnTrapThis Trap is sent every time a Remote External alarm 4 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.237 |
gnRExternalAlarm5OnTrapThis Trap is sent every time a Remote External alarm 5 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.238 |
gnRExternalAlarm6OnTrapThis Trap is sent every time a Remote External alarm 6 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.239 |
gnRExternalAlarm7OnTrapThis Trap is sent every time a Remote External alarm 7 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.240 |
gnRExternalAlarm8OnTrapThis Trap is sent every time a Remote External alarm 8 is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.241 |
gnRSystemFaultTrapThis Trap is sent every time a Remote System fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.242 |
gnRTftpFaultTrapThis Trap is sent every time a Remote TFTP Download fails. TRAP-TYPE .1.3.6.1.4.1.2281.0.243 |
gnRInternalDownloadFaultTrapThis Trap is sent every time a Remote internal Download fails. TRAP-TYPE .1.3.6.1.4.1.2281.0.244 |
gnRIntralinkFaultTrapThis Trap is sent every time a Remote intra-link download fails. TRAP-TYPE .1.3.6.1.4.1.2281.0.245 |
gnRConfMismatchTrapThis Trap is sent every time a Remote configuration mismatch fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.246 |
gnRProtectSwitchFaultTrapThis Trap is sent every time a Remote Protection fault is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.247 |
gnRProtectCableFaultTrapThis Trap is sent every time a Remote protection cable fault is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.248 |
gnRHeartBeatTrapThis Trap is a periodic heart beat trap. TRAP-TYPE .1.3.6.1.4.1.2281.0.249 |
gnRLomTrapThis Trap is sent every time a Remote Loss of Multi-frame alarm occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.250 |
gnRHitlessRadioLofTrapThis Trap is sent every time a Remote Hitless RadioLOF fault occurs. TRAP-TYPE .1.3.6.1.4.1.2281.0.252 |
gnRHitlessCableDisconnectTrapThis Trap is sent every time a Remote Hitless cable fault is raised. TRAP-TYPE .1.3.6.1.4.1.2281.0.253 |
gnRODUPowerOkTrapThis Trap is sent every time a Remote ODU Power fault cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.310 |
gnRODUSynthLockTrapThis Trap is sent every time a Remote ODU Hardware fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.311 |
gnRODUTxLevelInRangeTrapThis Trap is sent every time a Remote ODU TX signal is in range. TRAP-TYPE .1.3.6.1.4.1.2281.0.312 |
gnRODURxLevelInRangeTrapThis Trap is sent every time a Remote ODU RX signal is in range. TRAP-TYPE .1.3.6.1.4.1.2281.0.313 |
gnRODUNormalTempTrapThis Trap is sent every time a Remote ODU returns to normal temperature. TRAP-TYPE .1.3.6.1.4.1.2281.0.314 |
gnRIDUPowerOkTrapThis Trap is sent every time a Remote IDU Power fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.315 |
gnRCableOkTrapThis Trap is sent every time a Remote IDU-ODU cable fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.316 |
gnRModemOkTrapThis Trap is sent every time a Remote Modem faults is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.317 |
gnRIDUNormalTempTrapThis Trap is sent every time a Remote IDU returns to normal temperature. TRAP-TYPE .1.3.6.1.4.1.2281.0.318 |
gnRLoopbackOffTrapThis Trap is sent every time a Remote Loopback is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.319 |
gnRRemoteCommOkTrapThis Trap is sent every time the remote communication is re-connected. TRAP-TYPE .1.3.6.1.4.1.2281.0.320 |
gnRNoTestRunningTrapThis Trap is sent every time a Remote SDH/SONET test is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.321 |
gnRNoLOFTrapThis Trap is sent every time a Remote Loss of Frame alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.322 |
gnRNoLOSTrapThis Trap is sent every time a Remote Loss of Signal alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.323 |
gnRNoTIMTrapThis Trap is sent every time a Remote Trace Identifier Mismatch alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.324 |
gnRNoEXCTrapThis Trap is sent every time a Remote Excessive BER alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.325 |
gnRNoSDTrapThis Trap is sent every time a Remote Signal Degrade alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.326 |
gnRNoAisTrapThis Trap is sent every time the Remote terminal stops receiving an Alarm Indication Signal (AIS). TRAP-TYPE .1.3.6.1.4.1.2281.0.327 |
gnRNoUnExpTrapThis Trap is sent every time a Remote terminal stops receiving an unexpected signal. TRAP-TYPE .1.3.6.1.4.1.2281.0.328 |
gnRNoLocTrapThis Trap is sent every time a Remote Loss of Carrier (on the FE interfaces) alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.329 |
gnRNoLopTrapThis Trap is sent every time a Remote Loss of pointer alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.330 |
gnRNoRdiTrapThis Trap is sent every time the Remote terminal stops receiving a Remote Defect Identifier signal (RDI). TRAP-TYPE .1.3.6.1.4.1.2281.0.331 |
gnRNoSlmTrapThis Trap is sent every time a Remote Signal (Payload) Label Mismatch alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.332 |
gnRNoUnqTrapThis Trap is sent every time a Remote terminal start receiving an equipped signal. TRAP-TYPE .1.3.6.1.4.1.2281.0.333 |
gnRExternalAlarm1OffTrapThis Trap is sent every time a Remote External alarm 1 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.334 |
gnRExternalAlarm2OffTrapThis Trap is sent every time a Remote External alarm 2 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.335 |
gnRExternalAlarm3OffTrapThis Trap is sent every time a Remote External alarm 3 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.336 |
gnRExternalAlarm4OffTrapThis Trap is sent every time a Remote External alarm 4 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.337 |
gnRExternalAlarm5OffTrapThis Trap is sent every time a Remote External alarm 5 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.338 |
gnRExternalAlarm6OffTrapThis Trap is sent every time a Remote External alarm 6 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.339 |
gnRExternalAlarm7OffTrapThis Trap is sent every time a Remote External alarm 7 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.340 |
gnRExternalAlarm8OffTrapThis Trap is sent every time a Remote External alarm 8 is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.341 |
gnRSystemOkTrapThis Trap is sent every time a Remote System fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.342 |
gnRTftpOkTrapThis Trap is sent every time a Remote TFTP Download succeeded. TRAP-TYPE .1.3.6.1.4.1.2281.0.343 |
gnRInternalDownloadOkTrapThis Trap is sent every time a Remoteinternal Download succeeded. TRAP-TYPE .1.3.6.1.4.1.2281.0.344 |
gnRIntralinkOkTrapThis Trap is sent every time a Remote intra-link download succeeded. TRAP-TYPE .1.3.6.1.4.1.2281.0.345 |
gnRNoConfMismatchTrapThis Trap is sent every time a Remote configuration mismatch fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.346 |
gnRProtectCableOkTrapThis Trap is sent every time a Remote protection cable fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.348 |
gnRLomOkTrapThis Trap is sent every time a Remote Loss of Multi-frame alarm is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.350 |
gnRHitlessRadioLofOKTrapThis Trap is sent every time a Remote Hitless RadioLOF fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.352 |
gnRHitlessCableDisconnectOKTrapThis Trap is sent every time a Remote Hitless cable fault is cleared. TRAP-TYPE .1.3.6.1.4.1.2281.0.353 |
gnOID OBJECT IDENTIFIER .1.3.6.1.4.1.2281.1 |
gnFirstOID OBJECT IDENTIFIER .1.3.6.1.4.1.2281.1.1 |
gnSystem OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2 |
gnGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.1 |
gnGenStandardOrgThis parameter specifies which international standard is used.ro Enumeration .1.3.6.1.4.1.2281.2.1.1 |
gnGenTxFreqRangeThis parameter specifies frequency ranges in Hertz. Value 1 to 13 are used
when the link
is working with channels. The notUsed value is used when the link is
working with frequency.ro Enumeration .1.3.6.1.4.1.2281.2.1.2 |
gnGenRemoteConnectionIs the connection between the local manager and
the remote manager.ro Enumeration .1.3.6.1.4.1.2281.2.1.3 |
gnGenRemoteDistanceThis field is the distance between the local and remote ODU, in meters.
This attribute does not auto-detect the distance.
It is used as part of the unfaded RSL calculation feature in CERAGONView.rw INTEGER .1.3.6.1.4.1.2281.2.1.4 |
gnGenInterLenLocalRemoteThis field is the FEC interleaver length - DONT CHANGE THIS FIELD !!!.
WRITE will change both local and remote sides.rw INTEGER .1.3.6.1.4.1.2281.2.1.5 |
gnGenTxFreqLocalRemoteThis parameter indicates the radio TX channel number.
WRITE will change both LOCAL and REMOTE sides.
Not all radios will support TX frequency change via channel numbers.rw INTEGER .1.3.6.1.4.1.2281.2.1.6 |
gnGenRealTimeandDateThis parameter specifies the real time and date
Format 'YYYY-MM-DD,HH:MM:SS' (Hexadecimal).
A date-time specification.
field octets contents range
-
1 1-2 year 0..65536
2 3 month 1..12
3 4 day 1..31
4 5 hour 0..23
5 6 minutes 0..59
6 7 seconds 0..60
(use 60 for leap-second)
7 8 deci-seconds 0..9
8 9 direction from UTC '+' / '-'
9 10 hours from UTC 0..11
10 11 minutes from UTC 0..59
For example, Tuesday May 26, 1992 at 1:30:15 PM EDT
would be displayed as: 07 c8 05 1a 0d 1e 0f 00
( 1992 -5 -26,13:30:15 )
Note that if only local time is known, then timezone
information (fields 8-10) is not present.rw OCTET STRING .1.3.6.1.4.1.2281.2.1.7 |
gnGenCfgDeviceTableThis table contains general configuration info
per device, local and remote. SEQUENCE OF GnGenCfgDeviceEntry .1.3.6.1.4.1.2281.2.1.8 |
gnGenCfgDeviceEntryEntry containing general configuration information, for both local and
remote sides. GnGenCfgDeviceEntry .1.3.6.1.4.1.2281.2.1.8.1 |
gnGenCfgDeviceIdThis value indicates the device table entry (local or
Remote).ro Enumeration .1.3.6.1.4.1.2281.2.1.8.1.1 |
gnGenCfgDeviceResetPerfMonReset performance monitoring.rw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.2 |
gnGenCfgDeviceOperationThis parameter allows the NMS to perform operations.
(3) will implement software RESET
(4) will SET all factory default configurations, including IP address!
(5) will CLEAR IDU software
NOTE: CLEARING IDU software will cause the IDU to use the factory BOOT
software version.
4 and 5 will take place only after reset of the IDUrw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.3 |
gnGenCfgActivateLoopbackThis parameter controls the loop back diagnostics operations.
For remote units, only SPI, MUX and MDM loopbacks are allowed.rw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.4 |
gnGenCfgF1DataChanConnectorThis is the physical interface of the F1 line data channel
(USER CHANNEL connection).ro Enumeration .1.3.6.1.4.1.2281.2.1.8.1.5 |
gnGenCfgWaySideConnectorThis is the physical interface of the radio E1 way side channel
(WAYSIDE CHANNEL connection).ro Enumeration .1.3.6.1.4.1.2281.2.1.8.1.6 |
gnGenCfgActivateChanLoopbackThis parameter controls the USER CHANNEL and WAYSIDE channel
loopback diagnostic operations.
(3) will activate the 64k data channel loopback (USER CHANNEL)
(4) will activate the WAYSIDE CHANNEL loopback.rw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.7 |
gnGenCfgInterLenLocalOnlyThis field is the FEC interleaver length .DONT CAHNGE THIS FIELD !!! .
WRITE will change the local side only.rw INTEGER .1.3.6.1.4.1.2281.2.1.8.1.8 |
gnGenCfgSlipIpThis is the SERIAL interface IP address.
Included for future development, not currently supported.rw IpAddress .1.3.6.1.4.1.2281.2.1.8.1.9 |
gnGenCfgSlipModemConnectionThe telephone number to which the modem will initialize a call,
upon generation of a TRAP.
The number must be entered numerically (for example 18001234567).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.1.8.1.10 |
gnGenCfgSlipSpeedThe SERIAL interface baud rate.rw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.11 |
gnGenCfgAlarmSeverityThis field is used only by the Ceraview management
application
Every Trap severity 4 bits.
15 (MAJOR), 7 (MINOR), 3 (WARNING) and 1 (EVENT) options.
The first 4 bits ODU Power supply severity,
then the Synthesizer severity ,then Tx level then RX level
ODU temperature, ODU loopback , IDU power supply , Cable,
Modem, IDU temperature, IDU loopbacks, External Alarm 1,
External Alarm 2 ,External Alarm 3, External Alarm 4,
External Alarm 5, External Alarm 6, External Alarm 7,
External Alarm 8, Remote connectivity, LOF, LOS, EXC, SD
J0 mismatch and system fault.rw OCTET STRING .1.3.6.1.4.1.2281.2.1.8.1.12 |
gnGenCfgODUSerialNumberThis is the ODU serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.2.1.8.1.13 |
gnGenCfgIDUSerialNumberThis is the IDU serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.2.1.8.1.14 |
gnGenCfgAlarmTextThe private trap text, describing the last generated trap text.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.1.8.1.15 |
gnGenCfgTrapSeverityThe current Trap severity, describing the last generated trap
severityro Enumeration .1.3.6.1.4.1.2281.2.1.8.1.16 |
gnGenCfgProductTypeThe product type.ro Enumeration .1.3.6.1.4.1.2281.2.1.8.1.17 |
gnGenCfgLeftMediumConnectorFor ACCESS hardware, this indicates the first (left) interface connector.ro Enumeration .1.3.6.1.4.1.2281.2.1.8.1.18 |
gnGenCfgMiddleMediumConnectorFor ACCESS hardware, this indicates the second (right)interface connector.ro Enumeration .1.3.6.1.4.1.2281.2.1.8.1.19 |
gnGenCfgPrimaryClockSourceThe primary clock source, configurable for ACCESS radios only.rw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.20 |
gnGenCfgSecondaryClockSourceThe secondary clock source, configurable for ACCESS radios only.rw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.21 |
gnGenCfgTrapOptionThis item defines various trap options (0-31):
0 - SNSN (STANDARD TRAPS DO NOT INCLUDE SERIAL NUMBER)
1 - ASN (ALL TRAPS INCLUDE SERIAL NUMBER)
2 - SNSN, DNLR (DO NOT REPORT LOCAL TRAPS FROM REMOTE IDU)
3 - ASN, DNLR
4 - SNSN, EVT (USE DIFFERENT TRAP ID FOR EACH ALARM TYPE)
5 - ASN, EVT
6 - SNSN, DNLR, EVT
7 - ASN, DNLR, EVT
* - Add 8 to your choice for excluding traps with id >= 128.
Example: for SNSN, DNLR with this filter write 10 (=8+2).
** - Add another 16 to your choice in order to send 'clear' traps with zero severity.rw INTEGER .1.3.6.1.4.1.2281.2.1.8.1.22 |
gnGenCfgCLLICommon Language Location Identifier (maximum length: 30)rw DisplayString .1.3.6.1.4.1.2281.2.1.8.1.23 |
gnGenCfgHeartbeatPeriodThis item defines the number of minutes between each traprw INTEGER .1.3.6.1.4.1.2281.2.1.8.1.24 |
gnGenCfgGetRemoteData.rw Enumeration .1.3.6.1.4.1.2281.2.1.8.1.25 |
gnGenCfgClearLoopTimeoutThis item defines the clear loopbacks timeout in minutes.
possible values: 0..1440.
0 means disable.rw INTEGER .1.3.6.1.4.1.2281.2.1.8.1.26 |
gnGenCfgSubProductTypelsb bit: 1 if fibeair 1500i or 1528i 0 otherwise.ro INTEGER .1.3.6.1.4.1.2281.2.1.8.1.27 |
gnGenStatDeviceTableThis table contains general configuration info
per device; local and remote. SEQUENCE OF GnGenStatDeviceEntry .1.3.6.1.4.1.2281.2.1.9 |
gnGenStatDeviceEntryEntry containing general configuration information per device, both
local and remote sides. GnGenStatDeviceEntry .1.3.6.1.4.1.2281.2.1.9.1 |
gnGenStatDeviceIdThis value indicates which device is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.2.1.9.1.1 |
gnGenStatDeviceCelsiusTempThis is the temperature of the modem of the IDU in degrees of
Celsius.ro INTEGER (-10..70) .1.3.6.1.4.1.2281.2.1.9.1.2 |
gnGenStatDeviceFahrenheitTempThis is the temperature of the modem of the IDU in degrees of
Fahrenheit.ro INTEGER .1.3.6.1.4.1.2281.2.1.9.1.3 |
gnGenStatDevicePowerSupplyThis octet represents the status of the power
supplies of the IDU:
bit 1 on = 3.3V faulty
bit 2 on = -5V faulty
bit 3 on = 5V faulty.
bit 4 on = +8V faultyro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.4 |
gnGenStatDeviceCableStatus of the cable to the ODU.ro Enumeration .1.3.6.1.4.1.2281.2.1.9.1.5 |
gnGenStatDeviceDryContactThe status of the dry contacts, Each input status is represented by a bit.
When the input is on, the bit value is 0.When the input is off, the bit
value is 1.
The MSB represents external alarm 8. For example when only external alarm
1 is
on the status value will be 0xFE00ro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.6 |
gnGenStatDeviceLedsThe status of the IDU front panel LEDs. For the management station use.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.7 |
gnGenStatInternalCommunicationThe status of internal communication problem
bit 1 = 1: between main CPU and ODU CPU.
bit 2 = 1: between main CPU and MUX CPU.
bit 3 = 1: between master main CPU and slave main CPU.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.8 |
gnGenStatDeviceFanStatusThe status of the IDU fans 1-2 or 1-4.
bit 1 = IDU Fan1 is faulty.
bit 2 = IDU Fan2 is faulty.
bit 3 = IDU Fan2 is faulty.
bit 4 = IDU Fan2 is faulty.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.9 |
gnGenStatDeviceODUStatusODU status reported with this parameter.
Bit1 is MSB. The bit is set when a fault occurs.
The bit is cleared when the fault clears.
bit 1 = Power Supply status
bit 2 = Synthesizer lock status
bit 3 = Tx level status
bit 4 = ATPC status
bit 5 = Rx level status
bit 6 = Not currently used.
bit 7 = Temperature status
bit 8 = Not currently used.
bit 9 = ODU loopback status.
bit 10 = Internal use (by application).
bit 11 = Tx is in Mute.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.10 |
gnGenStatDeviceIDUStatusIDU status reported with this parameter. Bit1 is MSB.
The bit is set when a fault occurs. The bit is
cleared when the fault clears.
bit 1 = Power status
bit 2 = Cable open status
bit 3 = Cable short status
bit 4 = Modem Lock status
bit 5 = Temperature status
bit 6 = No signal from ODU (Phos only)
bit 7 = loopback status
bit 8 = External alarm 1 status
bit 9 = External alarm 2 status
bit 10 = External alarm 3 status
bit 11 = External alarm 4 status
bit 12 = External alarm 5 status
bit 13 = External alarm 6 status
bit 14 = External alarm 7 status
bit 15 = External alarm 8 status
bit 16 = Remote connectivity status.
bit 17 = Inner communication status.
bit 18 = Link ID mismatch status.
bit 19 = Configuration mismatch status.
bit 20 = Shelf Id mismatch status (Phos only).
bit 21 = General HW failure.
bit 22 = No power to MUX board.
bit 23 = No power to MODEM board.
bit 24 = IDC disk firmware cinfiguration mismatch.
bit 25 = Modem configuration file.
bit 26 = Wayside channel E1/T1 LOS
bit 27 = loopback on Wayside channelro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.11 |
gnGenStatDeviceRSTStatusThe bit is set when a fault occurs. The bit is
cleared when the fault clears.
bit 1 = Line loss of frame status
bit 2 = Radio loss of frame status
bit 3 = Line EXC status
bit 4 = Radio EXC status
bit 5 = Line SD status
bit 6 = Radio SD status
bit 7 = loss of signal status
bit 8 = J0 mismatch.
bit 9 = Line UNE status.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.9.1.12 |
gnGenChannelBandwidthThe TX channel bandwidth, displayed in 1/100 MHz.
For example:
An STM-1 ETSI TX channel bandwidth of 56MHz is displayed as the value 5600.ro INTEGER .1.3.6.1.4.1.2281.2.1.10 |
gnGenTxFreqNumLocalRemoteIndicates the radio transmit frequency, displayed in
1/100 MHz. WRITE changes the local and remote sides. Only for systems that
support frequency configuration (Not channel).rw INTEGER .1.3.6.1.4.1.2281.2.1.11 |
gnGenProtocolTypeThis is the radio mapping protocol. -C represents 'concatenated'.rw Enumeration .1.3.6.1.4.1.2281.2.1.12 |
gnGenLinkId0 for 'old' system that doesn't support the link ID.
the user can enter values from 1 to 65535rw INTEGER .1.3.6.1.4.1.2281.2.1.13 |
gnGenMibVersionThe current software version supports this MIB version (and the previous MIB versions).ro DisplayString .1.3.6.1.4.1.2281.2.1.14 |
gnGenModemTypeThe system modem type.ro Enumeration .1.3.6.1.4.1.2281.2.1.15 |
gnGenRadioSiderw Enumeration .1.3.6.1.4.1.2281.2.1.16 |
gnGenSystemWorkTimeThe System Work Time (hours).rw INTEGER .1.3.6.1.4.1.2281.2.1.17 |
gnGenRxFreqNumLocalRemoteIndicates the radio receive frequency, displayed in
1/100 MHz. WRITE changes the local and remote sides. Only for systems that
support frequency configuration (Not channel).rw INTEGER .1.3.6.1.4.1.2281.2.1.18 |
gnGenLastCfgTimeandDateThis parameter specifies the last configuration change time and date
Format 'YYYY-MM-DD,HH:MM:SS' (Hexadecimal).
A date-time specification.
field octets contents range
-
1 1-2 year 0..65536
2 3 month 1..12
3 4 day 1..31
4 5 hour 0..23
5 6 minutes 0..59
6 7 seconds 0..60
(use 60 for leap-second)
7 8 deci-seconds 0..9
8 9 direction from UTC '+' / '-'
9 10 hours from UTC 0..11
10 11 minutes from UTC 0..59
For example, Tuesday May 26, 1992 at 1:30:15 PM EDT
would be displayed as: 07 c8 05 1a 0d 1e 0f 00
( 1992 -5 -26,13:30:15 )
Note that if only local time is known, then timezone
information (fields 8-10) is not present.rw OCTET STRING .1.3.6.1.4.1.2281.2.1.19 |
gnGenMostSevereAlarmThis parameter specifies the current moset severe alarm in the system.ro Enumeration .1.3.6.1.4.1.2281.2.1.20 |
gnGenIdcCfgTable SEQUENCE OF GnGenIdcCfgEntry .1.3.6.1.4.1.2281.2.1.21 |
gnGenIdcCfgEntry GnGenIdcCfgEntry .1.3.6.1.4.1.2281.2.1.21.1 |
gnGenIdcCfgIdro Enumeration .1.3.6.1.4.1.2281.2.1.21.1.1 |
gnGenIdcCfgXpicModerw Enumeration .1.3.6.1.4.1.2281.2.1.21.1.2 |
gnGenIdcCfgResetPerfMonReset performance monitoring.rw Enumeration .1.3.6.1.4.1.2281.2.1.21.1.3 |
gnGenIdcCfgOperation.rw Enumeration .1.3.6.1.4.1.2281.2.1.21.1.4 |
gnGenIdcCfgWaySideConnectorThis is the physical interface of the radio E1 way side channel
(WAYSIDE CHANNEL connection).ro Enumeration .1.3.6.1.4.1.2281.2.1.21.1.5 |
gnGenIdcCfgHeartbeatPeriodThis item defines the number of minutes between each traprw INTEGER .1.3.6.1.4.1.2281.2.1.21.1.6 |
gnGenIdcCfgClearLoopTimeoutThis item defines the clear loopbacks timeout in minutes.
possible values: 0..1440.
0 means disable.rw INTEGER .1.3.6.1.4.1.2281.2.1.21.1.7 |
gnGenIdcCfgSlipIpThis is the SERIAL interface IP address.rw IpAddress .1.3.6.1.4.1.2281.2.1.21.1.8 |
gnGenIdcCfgSlipModemConnectionThe telephone number to which the modem will initialize a call,
upon generation of a TRAP.
The number must be entered numerically (for example 18001234567).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.1.21.1.9 |
gnGenIdcCfgSlipSpeedThe SERIAL interface baud rate.rw Enumeration .1.3.6.1.4.1.2281.2.1.21.1.10 |
gnGenIdcCfgAlarmSeverityThis field is used only by the Ceraview management application.rw OCTET STRING .1.3.6.1.4.1.2281.2.1.21.1.11 |
gnGenIdcCfgIDUSerialNumberThis is the IDU serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.2.1.21.1.12 |
gnGenIdcCfgTrapOptionThis item defines various trap options (0-15):
0 - SNSN (STANDARD TRAPS DO NOT INCLUDE SERIAL NUMBER)
1 - ASN (ALL TRAPS INCLUDE SERIAL NUMBER)
2 - SNSN, DNLR (DO NOT REPORT LOCAL TRAPS FROM REMOTE IDU)
3 - ASN, DNLR
4 - SNSN, EVT (EVENTS ARE REPORTED AS TRAPS)
5 - ASN, EVT
6 - SNSN, DNLR, EVT
7 - ASN, DNLR, EVT
* - Add 8 to your choice for excluding traps with id >= 128.
Example: for SNSN, DNLR with this filter write 10 (=8+2).
** - Add another 16 to your choice in order to send 'clear' traps with zero severity.rw INTEGER .1.3.6.1.4.1.2281.2.1.21.1.13 |
gnGenIdcCfgCLLICommon Language Location Identifier (maximum length: 30)rw DisplayString .1.3.6.1.4.1.2281.2.1.21.1.14 |
gnGenIdcCfgEowCascadeStatusNot used!!.rw Enumeration .1.3.6.1.4.1.2281.2.1.21.1.15 |
gnGenIdcCfgSerialPPPAdminStatusEnable\Disable PPP over serial interface.rw Enumeration .1.3.6.1.4.1.2281.2.1.21.1.16 |
gnGenIdcStatTable SEQUENCE OF GnGenIdcStatEntry .1.3.6.1.4.1.2281.2.1.22 |
gnGenIdcStatEntry GnGenIdcStatEntry .1.3.6.1.4.1.2281.2.1.22.1 |
gnGenIdcStatIdro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.1 |
gnGenIdcStatXpicSupportro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.2 |
gnGenIdcStatLedsro OCTET STRING .1.3.6.1.4.1.2281.2.1.22.1.3 |
gnGenIdcStatIDUStatusIDU status reported with this parameter. Bit1 is MSB.
The bit is set when a fault occurs. The bit is
cleared when the fault clears.
bit 1 = Fans status
bit 2 = configuration mismatch
bit 3 = Internal use
bit 4 = Internal use
bit 5 = XPIC cable swap
bit 6 = External alarm 1 status
bit 7 = External alarm 2 status
bit 8 = External alarm 3 status
bit 9 = External alarm 4 status
bit 10 = External alarm 5 status
bit 12 = External alarm 6 status
bit 13 = External alarm 7 status
bit 14 = External alarm 8 status
bit 15 = Auxiliary interface card is downro OCTET STRING .1.3.6.1.4.1.2281.2.1.22.1.4 |
gnGenIdcStatMMCCardStatusBit1 is MSB.
bit 1 = 0=MMC card exist, 1=MMC card not exist
bit 2 = MMC card status: 0=ok, 1=faultro OCTET STRING .1.3.6.1.4.1.2281.2.1.22.1.5 |
gnGenIdcStatDryContactThe status of the dry contacts, Each input status is represented by a bit.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.22.1.6 |
gnGenIdcStatFanStatusThe status of the IDU fans 1-2 or 1-4.
bit 1 = IDU Fan1 is faulty.
bit 2 = IDU Fan2 is faulty.
bit 3 = IDU Fan2 is faulty.
bit 4 = IDU Fan2 is faulty.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.22.1.7 |
gnGenIdcStatLeftDrawerStatusro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.8 |
gnGenIdcStatRightDrawerStatusro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.9 |
gnGenIdcStatHitlessSupportIndication for hitless support.ro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.10 |
gnGenIdcStatEowExistenceThis parameter sight physical existence of the EOW connector.ro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.11 |
gnGenIdcStatEowSupportIndication for EOW (cascade) support.ro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.12 |
gnGenIdcStatIduPositionIndication for idu position.ro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.13 |
gnGenIdcStatBoardTypeIndication for the board type.ro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.14 |
gnGenIdcStatAgentIPAddressIndication for the Agent IP address.ro IpAddress .1.3.6.1.4.1.2281.2.1.22.1.15 |
gnGenIdcStatInterfaceConnectorIndication for the interface connector type.ro Enumeration .1.3.6.1.4.1.2281.2.1.22.1.16 |
gnGenIdcStatIfTableCounterThis counter is initialize to a random number and increment on every change of the IfTable
(This is for NMS use).ro INTEGER .1.3.6.1.4.1.2281.2.1.22.1.17 |
gnGeneralXTable SEQUENCE OF GnGeneralXEntry .1.3.6.1.4.1.2281.2.1.23 |
gnGeneralXEntry GnGeneralXEntry .1.3.6.1.4.1.2281.2.1.23.1 |
gnGenXIdro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.1 |
gnGenXStandardOrgThis parameter specifies which international standard is used.ro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.2 |
gnGenXRemoteConnectionIs the connection between the local manager and
the remote manager.ro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.3 |
gnGenXLinkId0 for 'old' system that doesn't support the link ID.
the user can enter values from 1 to 65535rw INTEGER .1.3.6.1.4.1.2281.2.1.23.1.4 |
gnGenXModemTypeThe system modem type.ro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.5 |
gnGenXRadioSiderw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.6 |
gnGenXSystemWorkTimeThe System Work Time (hours).rw INTEGER .1.3.6.1.4.1.2281.2.1.23.1.7 |
gnGenXOperation.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.8 |
gnGenXResetPerfMonReset performance monitoring.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.9 |
gnGenXAlarmSeverityThis field is used only by the Ceraview management
application Every Trap severity 4 bits.
15 (MAJOR), 7 (MINOR), 3 (WARNING) and 1 (EVENT) options.
The first 4 bits ODU Power supply severity,
then the Synthesizer severity ,then Tx level then RX level
ODU temperature, ODU loopback , IDU power supply , Cable,
Modem, IDU temperature, IDU loopbacks, External Alarm 1,
External Alarm 2 ,External Alarm 3, External Alarm 4,
External Alarm 5, External Alarm 6, External Alarm 7,
External Alarm 8, Remote connectivity, LOF, LOS, EXC, SD
J0 mismatch and system fault.rw OCTET STRING .1.3.6.1.4.1.2281.2.1.23.1.10 |
gnGenXCarrierSerialNumberThis is the carrier serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.2.1.23.1.11 |
gnGenXMUXSerialNumberThis is the MUX serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.2.1.23.1.12 |
gnGenXProductTypeThe product type.ro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.13 |
gnGenXCarrierConnectorFor ACCESS hardware, this indicates the first (left) interface connector.ro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.14 |
gnGenXInterfacesLedsThe status of the Interface LEDs. For the management station use.
Each two bits represents one led as follows: 00 - Gray, 01 - Green, 10 - Orange, 11 - Red.
The led order: Led1 is msb 2 bits , after it led2, till led 16 - 2 lsb bits.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.23.1.15 |
gnGenXMultiRateMultiConsConfThe Link data capacityrw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.16 |
gnGenXMultiRateMultiConsSupportro OCTET STRING .1.3.6.1.4.1.2281.2.1.23.1.17 |
gnGenXWaysideChannelEnable Disable drawer wayside channelrw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.18 |
gnGenXWaySideLoopbackThis parameter controls the WAYSIDE channel loopback diagnostic operations.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.19 |
gnGenXSyncIdcDataBase.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.20 |
gnGenXAesEnableThis parameter defines encryption admin mode.ro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.21 |
gnGenXAesMkeyModeThis parameter is not used.ro Enumeration .1.3.6.1.4.1.2281.2.1.23.1.22 |
gnGenXActNumOfInterfaceOnClass1This value indicates the actual number of interfaces on class 1.ro INTEGER .1.3.6.1.4.1.2281.2.1.23.1.23 |
gnGenXActNumOfInterfaceOnClass2This value indicates the actual number of interfaces on class 2.ro INTEGER .1.3.6.1.4.1.2281.2.1.23.1.24 |
gnGenXActNumOfInterfaceOnClass3This value indicates the actual number of interfaces on class 3.ro INTEGER .1.3.6.1.4.1.2281.2.1.23.1.25 |
gnGenXEowStatusNot used.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.26 |
gnGenXTempLicenseEnableSet temporary license enable or disable.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.27 |
gnGenXTempLicenseTimerThis value indicates the temporary license timer.ro INTEGER .1.3.6.1.4.1.2281.2.1.23.1.28 |
gnGenXDefectBlocksThe number of defected blocks that could not be corrected by the
FECro INTEGER .1.3.6.1.4.1.2281.2.1.23.1.29 |
gnGenXBytesCorrectedNumber of bytes corrected by the FECro INTEGER .1.3.6.1.4.1.2281.2.1.23.1.30 |
gnGenXPrbsTestThis parameter enable the user to activate the PRBS test.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.31 |
gnGenXClearCountersThis parameter enable the user to clear the PRBS counters.rw Enumeration .1.3.6.1.4.1.2281.2.1.23.1.32 |
gnGenAddAlarmExtToTrapsIf chose 'yes', the Alarm Id, Origin and Unit from gnAgnCurrentAlarmTable
will be bind to the end of each ceragon private trap.rw Enumeration .1.3.6.1.4.1.2281.2.1.24 |
gnGenFeatureSupportInidcation for feature support. msb is for bit #1.
The bit is set when a specific feature is support.
Bit #1 - Tftp server support.
Bit #2 - Cold reset support.
Bit #3 - Severity critical for external alarm.
Bit #4 - MRMC filter table.
Bit #5 - NeighborIP Support Fast and DS3.
Bit #6 - Auxiliary channel drawer routing support.
Bit #7 - Single drawer external protection support.
Bit #8 - dual drawer external protection not support.
Bit #9 - Left Drawer XPIC hardware support (0 - support, 1 - not support).
Bit #10 - Right Drawer XPIC hardware support (0 - support, 1 - not support).
Bit #11 - Internal Protection Not Supported (0 - support, 1 - not support).
Bit #12 - One Ws Channel Only (0 - FALSE, 1 - TRUE).
Bit #13 - Protect option not support (0 - support, 1 - not support).
Bit #14 - UC ethernet support (0 - not support, 1 - support).
Bit #15 - WSC only disable (0 - enable & disable, 1 - only disable).
Bit #16 - UC only disable (0 - enable & disable, 1 - only disable).
Bit #17 - EOW only disable (0 - enable & disable, 1 - only disable).
Bit #18 - Left Drawer modem latency Not support (0 - support, 1 - not support).
Bit #19 - Right Drawer modem latency Not support (0 - support, 1 - not support).
Bit #20 - Clear PM for drawer (0 - support, 1 - not support).
Bit #21 - Allow Sync mode in UC#2 (0 - not allow, 1 - allow).ro OCTET STRING .1.3.6.1.4.1.2281.2.1.25 |
gnGeneralMrmcXTable SEQUENCE OF GnGeneralMrmcXEntry .1.3.6.1.4.1.2281.2.1.26 |
gnGeneralMrmcXEntryThis table indicates the supported modem configuration script for each drawer. GnGeneralMrmcXEntry .1.3.6.1.4.1.2281.2.1.26.1 |
gnGenMrmcXIdDrawer number.ro Enumeration .1.3.6.1.4.1.2281.2.1.26.1.1 |
gnGenMrmcXMrmcValThis parameter specifies MRMC value.ro INTEGER .1.3.6.1.4.1.2281.2.1.26.1.2 |
gnGenMrmcXBitRateThis parameter specifies transfer bit rate.ro INTEGER .1.3.6.1.4.1.2281.2.1.26.1.3 |
gnGenMrmcXBandWidthThis parameter specifies channel band width.ro INTEGER .1.3.6.1.4.1.2281.2.1.26.1.4 |
gnGenMrmcXQamThis parameter specifies modem qam.ro INTEGER .1.3.6.1.4.1.2281.2.1.26.1.5 |
gnGenDrawerXTableThis table indicates drawer x. SEQUENCE OF GnGenDrawerXEntry .1.3.6.1.4.1.2281.2.1.27 |
gnGenDrawerXEntryEntry containing drawer x namd and id. GnGenDrawerXEntry .1.3.6.1.4.1.2281.2.1.27.1 |
gnGenDrawerXIdThis value indicates the drawer's idro Enumeration .1.3.6.1.4.1.2281.2.1.27.1.1 |
gnGenDrawerXNameThis value indicates the drawer's namerw DisplayString .1.3.6.1.4.1.2281.2.1.27.1.2 |
gnGenDrawerXSlot1StatusnotExist - board not exist.
powerOff - board inserted and power off.
powerOn - board inserted and power on.
dbReady - board is power on and DB ready.ro Enumeration .1.3.6.1.4.1.2281.2.1.27.1.3 |
gnGenDrawerXSlot2StatusnotExist - board not exist.
powerOff - board inserted and power off.
powerOn - board inserted and power on.
dbReady - board is power on and DB ready.ro Enumeration .1.3.6.1.4.1.2281.2.1.27.1.4 |
gnGenDrawerXDeviceLedsThe status of the IDU front panel LEDs. For the management station use.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.27.1.5 |
gnGenDrawerXInternalCommunicationThe status of internal communication problem
bit 1 = 1: between main CPU and ODU CPU.
bit 2 = 1: between main CPU and MUX CPU.
bit 3 = 1: between master main CPU and slave main CPU.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.27.1.6 |
gnGenDrawerXDeviceIDUStatusIDU status reported with this parameter. Bit1 is MSB.
The bit is set when a fault occurs. The bit is
cleared when the fault clears.
bit 1 = Power status
bit 2 = Cable open status
bit 3 = Cable short status
bit 4 = Modem Lock status
bit 5 = Temperature status
bit 6 = No signal from ODU (Phos only)
bit 7 = loopback status
bit 8 = External alarm 1 status
bit 9 = External alarm 2 status
bit 10 = External alarm 3 status
bit 11 = External alarm 4 status
bit 12 = External alarm 5 status
bit 13 = External alarm 6 status
bit 14 = External alarm 7 status
bit 15 = External alarm 8 status
bit 16 = Remote connectivity status.
bit 17 = Inner communication status.
bit 18 = Link ID mismatch status.
bit 19 = Configuration mismatch status.
bit 20 = Shelf Id mismatch status (Phos only).
bit 21 = General HW failure.
bit 22 = No power to MUX board.
bit 23 = No power to MODEM board.
bit 24 = IDC disk firmware cinfiguration mismatch.
bit 25 = Modem configuration file.
bit 26 = Wayside channel E1/T1 LOS
bit 27 = loopback on Wayside channelro OCTET STRING .1.3.6.1.4.1.2281.2.1.27.1.7 |
gnCluster OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.1.28 |
cluster OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.1.28.1 |
clusterSystemTypeThis value indicates the system type: Phophorus, Avalon or Unknown Backplanero Enumeration .1.3.6.1.4.1.2281.2.1.28.1.1 |
clusterNumOfSubRacksThis value indicates the number of subrack, 1st phase supporsts only 1ro INTEGER .1.3.6.1.4.1.2281.2.1.28.1.3 |
clusterSubRackNumThis value indicates the subrack's numberro INTEGER .1.3.6.1.4.1.2281.2.1.28.1.4 |
clusterFloorNumThis value indicates the subrack's numberro INTEGER .1.3.6.1.4.1.2281.2.1.28.1.5 |
clusterIPBaseThis value indicates the Cluster IP basero IpAddress .1.3.6.1.4.1.2281.2.1.28.1.6 |
clusterIDCRoleThis value indicates - ClusterPrime - 2nd floor of 1st rack, SubRackManager - 2nd floor of other racks.ro Enumeration .1.3.6.1.4.1.2281.2.1.28.1.7 |
clusterPrimeIPAddressThis value enable CV/PV to know the server IP even if it is not connectedro IpAddress .1.3.6.1.4.1.2281.2.1.28.1.8 |
clusterPeerIPLastChangeTimeThis value indicates The last time when the Peer IP Table changedro INTEGER .1.3.6.1.4.1.2281.2.1.28.1.9 |
addressesTableThis table indicates the cluster's IP Addresses. SEQUENCE OF AddressesEntry .1.3.6.1.4.1.2281.2.1.28.2 |
addressesEntryEntry containing the cluster's IP Addresses. AddressesEntry .1.3.6.1.4.1.2281.2.1.28.2.1 |
addressesPeerIPIdThis value indicates the peer IP idro INTEGER .1.3.6.1.4.1.2281.2.1.28.2.1.1 |
addressesPeerIPAddressThis value indicates the IP address of a Server/Client.ro IpAddress .1.3.6.1.4.1.2281.2.1.28.2.1.2 |
primeIDC OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.1.28.3 |
primeIDCAutoInternalClockDistributionThis value indicates whether the internal clock distribution is enabled or disabled.rw Enumeration .1.3.6.1.4.1.2281.2.1.28.3.1 |
primeIDCSynchronizeClockInClusterThis value indicates whether to synchronize the clock in the cluster.rw Enumeration .1.3.6.1.4.1.2281.2.1.28.3.2 |
backplaneSlotMappingTableThis table indicates the cluster's IP Addresses. SEQUENCE OF BackplaneSlotMappingEntry .1.3.6.1.4.1.2281.2.1.28.4 |
backplaneSlotMappingEntryEntry containing the cluster's IP Addresses. BackplaneSlotMappingEntry .1.3.6.1.4.1.2281.2.1.28.4.1 |
backplaneSlotMappingSubrackIdThis value indicates the subrack index.ro INTEGER .1.3.6.1.4.1.2281.2.1.28.4.1.1 |
backplaneSlotMappingFloorIdThis value indicates the floor id
The 4U floor index (upper) will be 99.ro INTEGER .1.3.6.1.4.1.2281.2.1.28.4.1.2 |
backplaneSlotMappingDrawerIdFor floors 1-3: IDC=1, Drawer 1=2, Drwaer2 =3. For 4U floor (floor #99), Aux=1, Power=2.ro INTEGER .1.3.6.1.4.1.2281.2.1.28.4.1.3 |
backplaneSlotMappingSubDrawerIdThis value indicates the sub drawer id
IDC, Drawer 1 & 2 will be only 1. XC main (up) will be 1 and XC backup (lower) will be 2.ro INTEGER .1.3.6.1.4.1.2281.2.1.28.4.1.4 |
backplaneSlotMappingUnitTypeThe values are the same as in gnAgnCurrentAlarm Unit.ro Enumeration .1.3.6.1.4.1.2281.2.1.28.4.1.5 |
backplaneSlotMappingUnitNumberThis value indicates the unit number.ro INTEGER .1.3.6.1.4.1.2281.2.1.28.4.1.6 |
backplaneSlotMappingUnitIndexThis value indicates the unit number.ro INTEGER .1.3.6.1.4.1.2281.2.1.28.4.1.7 |
gnSubrack OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.1.29 |
powerInputTableThis table indicates the Power Input. SEQUENCE OF PowerInputEntry .1.3.6.1.4.1.2281.2.1.29.1 |
powerInputEntryEntry containing the Power Input. PowerInputEntry .1.3.6.1.4.1.2281.2.1.29.1.1 |
powerInputIdThis value indicates the power input Id.ro INTEGER .1.3.6.1.4.1.2281.2.1.29.1.1.1 |
powerInputAdminThis value indicates whether the power input Admin is enables or disabled.rw Enumeration .1.3.6.1.4.1.2281.2.1.29.1.1.2 |
powerInputStatusThis value indicates whether the power input is up or down, Notexist when power input card not exist. unknown when no A-Aux.ro Enumeration .1.3.6.1.4.1.2281.2.1.29.1.1.3 |
powerInputLedStatusThis value, Led1 is MSB 2 bits.
Each two bits represents one led:00 - Gray,01 - Green, 10 - Orange, 11 - Red.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.29.1.1.4 |
auxiliaryDrawer OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.1.29.2 |
auxiliaryDrawerAuxCardTypeThis value indicates whether the Auxiliary Card type.ro Enumeration .1.3.6.1.4.1.2281.2.1.29.2.1 |
auxiliaryDrawerLedsStatusThis value, Led16 is MSB 2 bits, Led1 is LSB 2 bits.
Each two bits represents one led:00 - Gray,01 - Green, 10 - Orange, 11 - Red.
Led 1: Status of WSC/UC Ethernet (upper connector, left side).
Led 2: Status of WSC/UC Ethernet (upper connector, right side).
Led 3: Status of WSC/UC Ethernet (lower connector, left side).
Led 4: Status of WSC/UC Ethernet (lower connector, right side).
Led 5: Reserved - Status of managment link (upper connector).
Led 6: Reserved - Status of managment activity (upper connector).
Led 7: Reserved - Status of managment link (lower connector).
Led 8: Reserved - Status of managment activity (lower connector).
Led 9: Status of WSC E1/T1 (upper connector, left side).
Led 10: Status of WSC E1/T1 (upper connector, right side).
Led 11: Status of WSC E1/T1 (lower connector, left side).
Led 12: Status of WSC E1/T1 (lower connector, right side).
Led 13: Reserved - Status of external fans (upper connector, left side).
Led 14: Reserved - Status of external fans (upper connector, right side).
Led 15: Reserved - Status of EOW Chaining (lower connector, left side).
Led 16: Reserved - Status of EOW Chaining (lower connector, right side).ro OCTET STRING .1.3.6.1.4.1.2281.2.1.29.2.2 |
auxiliaryDrawerBoardHWVersionThis value indicates the EEPROM value.ro INTEGER .1.3.6.1.4.1.2281.2.1.29.2.3 |
auxiliaryDrawerBoardFWVersionThis value indicates the Register value .ro DisplayString .1.3.6.1.4.1.2281.2.1.29.2.4 |
auxiliaryDrawerBoardPostResetFWVersionThis value indicates the Register value .ro DisplayString .1.3.6.1.4.1.2281.2.1.29.2.5 |
auxiliaryDrawerSerialNumberThis value indicates the EEPROM value.ro DisplayString .1.3.6.1.4.1.2281.2.1.29.2.6 |
auxiliaryDrawerBoardResetThis value indicates whether to reset board.rw Enumeration .1.3.6.1.4.1.2281.2.1.29.2.7 |
auxiliaryDrawerOrderWireChainingThis value indicates whether the Order Wire chaining is enables or disabled.rw Enumeration .1.3.6.1.4.1.2281.2.1.29.2.8 |
xcDrawerTableThis table indicates the XC Drawer. SEQUENCE OF XCDrawerEntry .1.3.6.1.4.1.2281.2.1.29.3 |
xcDrawerEntryEntry containing the XC Drawer. XCDrawerEntry .1.3.6.1.4.1.2281.2.1.29.3.1 |
xcDrawerXCIdThis value, 1-2 for 1st rack, 3-4 for 2nd, 5-6 for 3rdy.ro INTEGER .1.3.6.1.4.1.2281.2.1.29.3.1.1 |
xcDrawerLedsStatusThis value, Led1 is MSB 2 bits, Led4 is LSB .
Each two bits represents one led:00 - Gray,01 - Green, 10 - Orange, 11 - Red.ro OCTET STRING .1.3.6.1.4.1.2281.2.1.29.3.1.2 |
xcDrawerBoardHWVersionThis value indicates the EEPROM value.ro INTEGER .1.3.6.1.4.1.2281.2.1.29.3.1.3 |
xcDrawerBoardFWVersionThis value indicates the Register value .ro DisplayString .1.3.6.1.4.1.2281.2.1.29.3.1.4 |
xcDrawerBoardPostResetFWVersionThis value indicates the Register value .ro DisplayString .1.3.6.1.4.1.2281.2.1.29.3.1.5 |
xcDrawerSerialNumberThis value indicates the EEPROM value.ro DisplayString .1.3.6.1.4.1.2281.2.1.29.3.1.6 |
xcDrawerResetXCBoardThis value indicates whether to reset XC.rw Enumeration .1.3.6.1.4.1.2281.2.1.29.3.1.7 |
xcDrawerXCSelfTestResultThis value indicates the XC self test result.ro Enumeration .1.3.6.1.4.1.2281.2.1.29.3.1.8 |
xcDrawerXCActivityRoleThis value indicates the XC activity role.ro Enumeration .1.3.6.1.4.1.2281.2.1.29.3.1.9 |
xcDrawerSyncIdcDataBase.rw Enumeration .1.3.6.1.4.1.2281.2.1.29.3.1.10 |
xcDrawerXCConnectorThis value indicates the XC activity role.ro Enumeration .1.3.6.1.4.1.2281.2.1.29.3.1.11 |
gnGenCarrierXTableThis table indicates carrier x. SEQUENCE OF GnGenCarrierXEntry .1.3.6.1.4.1.2281.2.1.30 |
gnGenCarrierXEntryEntry of carrier x. GnGenCarrierXEntry .1.3.6.1.4.1.2281.2.1.30.1 |
gnGenCarrierXIdThis value indicates the carrier idro Enumeration .1.3.6.1.4.1.2281.2.1.30.1.1 |
gnGenCarrierXResetPerfMonReset performance monitoring.rw Enumeration .1.3.6.1.4.1.2281.2.1.30.1.2 |
gnGenCarrierXSyncIdcDataBaseidcToDrawer - copy configuration from the IDC disk to the HW (this operation istraffic effected).
drawerToIdc - copy configuration from HW to IDC disk.
this operation used to clear User Configuration Mismatch alarm.rw Enumeration .1.3.6.1.4.1.2281.2.1.30.1.3 |
gnAgn OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2 |
gnAgnMgrTableThis table indicates the managers list that will receive traps. SEQUENCE OF GnAgnMgrEntry .1.3.6.1.4.1.2281.2.2.1 |
gnAgnMgrEntryEntry containing the managers IP addresses and the trap filter options. GnAgnMgrEntry .1.3.6.1.4.1.2281.2.2.1.1 |
gnAgnMgrIdThis value indicates an index of a specific managerro INTEGER .1.3.6.1.4.1.2281.2.2.1.1.1 |
gnAgnMgrIPThis value indicates the managers IP address.
WRITE an IP address of all zeroes (0.0.0.0) will remove the entry.rw IpAddress .1.3.6.1.4.1.2281.2.2.1.1.2 |
gnAgnMgrAlarmGroupMaskbit mask .1 is 'send a trap' 0 is 'dont send a trap'.
The list of alarms from MSB to LSB is:
bit 1 = Power Supply Alarm
bit 2 = Cable Alarm
bit 3 = Temperature Alarm
bit 4 = External Alarm
bit 5 = Radio Alarm
bit 6 = Modem Alarm
bit 7 = Line Alarm
bit 8 = SDH Alarm
bit 9 = BER Alarm
bit 10 = System fault Alarm
bit 11 = Maintenance Alarm
If this field is 0, only standard traps will be sent to the managerrw OCTET STRING .1.3.6.1.4.1.2281.2.2.1.1.3 |
gnAgnMgrSeverityFilterThis is a bit mask value for masking traps according to its severity.
There is a bit for each severity. If the relevant bit is on (1), then
the Agent will send traps with this severity, and it won't send if the
bit is off (0).
The list of bits from LSB to MSB:
bit 1 (LSB) = Event.
bit 2 = Warning.
bit 3 = Minor.
bit 4 = Major.
bit 5 (MSB) = Critical.rw OCTET STRING .1.3.6.1.4.1.2281.2.2.1.1.4 |
gnAgnMgrTrapPortThe Port for sending the trap for each manager (possible values: 70-65535)rw INTEGER .1.3.6.1.4.1.2281.2.2.1.1.5 |
gnAgnLogFileData OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.2 |
gnAgnLogFileMaxEntriesThe maximum number of entries.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.1 |
gnAgnLogFileValidEntriesThis is the number of valid entries in the current logfile.
When this value exceeds 70% of capacity (100 entries),
the management station should store the file in its hard
disk.
If the management station is not active, the MIB will display up to
100
recent logfile eventsro INTEGER .1.3.6.1.4.1.2281.2.2.2.2 |
gnAgnLogFileActionThis attribute allows for logfile actions,
CLEARing the logfile and/or SAVING the logfile.rw Enumeration .1.3.6.1.4.1.2281.2.2.2.3 |
gnAgnLogFileTableThis table is the agents alarm and event log file. SEQUENCE OF GnAgnLogFileEntry .1.3.6.1.4.1.2281.2.2.2.4 |
gnAgnLogFileEntryEntry containing the agents alarm and event log file. GnAgnLogFileEntry .1.3.6.1.4.1.2281.2.2.2.4.1 |
gnAgnLogFileIdThis value indicates the index of an alarm logfile entry.
Entry 1 is the most recent logfile
eventro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.1 |
gnAgnLogFileValidThis value indicates the validity of the indexed alarm logfile entry.
a VALID log entry is (2) and an INVALID entry is (3).ro Enumeration .1.3.6.1.4.1.2281.2.2.2.4.1.2 |
gnAgnLogFileDateThis field is the date the alarm occurred, formatted as YYYY-MM-DD.
YYYY represents the year, MM the month and DD -the day.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.2.2.4.1.3 |
gnAgnLogFileTimeThis field is the hour the alarm occurred - format HH:MM.
HH - Hour, MM - minutero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.2.2.4.1.4 |
gnAgnLogFileSeverityThis value indicates the severity of the alarm,
31 for CRITICAL, 15 for MAJOR, 7 for MINOR, 3 for WARNING and 1 for EVENT.ro Enumeration .1.3.6.1.4.1.2281.2.2.2.4.1.5 |
gnAgnLogFileTextThis field describes the alarm that occurred. Max length 40
characters.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.2.2.4.1.6 |
gnAgnLogFileDeviceCelsiusTempThis is the temperature of the IDU in degrees Celsius,
during the alarm acceptance.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.7 |
gnAgnLogFileDevicePowerSupplyThis is the Power supply status of the IDU, during the alarm
acceptance
bit 1 on = 3.3V faulty
bit 2 on = -5V faulty
bit 3 on = 5V faulty.
bit 4 on = +8V faultyro OCTET STRING .1.3.6.1.4.1.2281.2.2.2.4.1.8 |
gnAgnLogFileInternalCommunicationThis is the internal communication status of the IDU, during the alarm
acceptance
bit 1 = 1: between main CPU and ODU CPU.
bit 2 = 1: between main CPU and MUX CPU.
bit 3 = 1: between master main CPU and slave main CPU.ro OCTET STRING .1.3.6.1.4.1.2281.2.2.2.4.1.9 |
gnAgnLogFileDeviceFanStatusThis is the Fan status of the IDU, during the alarm acceptance
bit 1 = Fan1 is faulty.
bit 2 = Fan 2 is faulty.ro OCTET STRING .1.3.6.1.4.1.2281.2.2.2.4.1.10 |
gnAgnLogFileDeviceODUStatusThis is the ODU status during the alarm acceptance
bit 1 MSB
bit 1 = Power Supply status
bit 2 = Synthesizer lock status
bit 3 = Tx level status
bit 4 = ATPC status
bit 5 = Rx level status
bit 6 = Not currently used
bit 7 = Temperature status
bit 8 = Not currently used.
bit 9 = Not currently usedro OCTET STRING .1.3.6.1.4.1.2281.2.2.2.4.1.11 |
gnAgnLogFileDeviceIDUStatusThis is the IDU status during the alarm acceptance
bit 1 MSB
bit 1 = Power status -
bit 2 = Cable open status -
bit 3 = Cable short status -
bit 4 = Modem Lock status
bit 5 = Temperature status
bit 6 = Not currently used.
bit 7 = loopback status
bit 8 = External alarm 1 status
bit 9 = External alarm 2 status
bit 10 = External alarm 3 status
bit 11 = External alarm 4 status
bit 12 = External alarm 5 status
bit 13 = External alarm 6 status
bit 14 = External alarm 7 status
bit 15 = External alarm 8 status
bit 16 = Remote connectivity status.
bit 17 = Inner communication status.ro OCTET STRING .1.3.6.1.4.1.2281.2.2.2.4.1.12 |
gnAgnLogFileOduCelsiusTempThis is the temperature of the ODU in degrees Celsius,
during the alarm acceptance.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.13 |
gnAgnLogFileOduReceiveLevelThis is the received signal level in DBM, during the alarm acceptancero INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.14 |
gnAgnLogFileOduSynthesizerVCOLockThis is the Synthesizer status, during the alarm acceptance
bit 1 on = TX IF synthesizer fault
bit 2 on = RX IF synthesizer fault
bit 3 on = Xband synthesizer fault
bit 4 on = History TX IF synthesizer fault
bit 5 on = History RX IF synthesizer fault
bit 6 on = History Xband synthesizer faultro OCTET STRING .1.3.6.1.4.1.2281.2.2.2.4.1.15 |
gnAgnLogFileOduPowerSupplyThis is the ODU power supply status, during the alarm acceptance
bit 1 on = +5V faulty
bit 2 on = +8V faulty
bit 3 on = +12V faulty
bit 4 on = -12V faulty.ro OCTET STRING .1.3.6.1.4.1.2281.2.2.2.4.1.16 |
gnAgnLogFileLineBERCurThis is the Line BER (Bit Error Rate), during the alarm acceptance.
Included for future development, not currently supported.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.17 |
gnAgnLogFileRadioBERCurThis is the Radio BER (Bit Error Rate), during the alarm acceptance.
Included for future development, not currently supported.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.18 |
gnAgnLogFileModStatusThis is the Modulator status, during the alarm acceptance
ok(2),
modulatorFault(3)ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.19 |
gnAgnLogFileDemodStatusThis is the Demodulator status, during the alarm acceptance . This field
is for Ceragon
internal debuggingro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.20 |
gnAgnLogFileLastDemodDefectBlocksThis is the number of the Defected blocks (blocks that couldn't be
corrected)
by the FEC, during the alarm acceptance last second.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.21 |
gnAgnLogFileLastDemodBytesCorrectedThis is the number of the bytes that were corrected by the FEC,
during the alarm acceptance last second.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.22 |
gnAgnLogFileLastDemodBlocksCorrectedThis is the number of the blocks that were corrected by the FEC
, during the alarm acceptance last second.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.23 |
gnAgnLogFileUniqueIdUnique Id for each log from 1 to 2,147,483,647 ( = 0x7FFFFFFF).ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.24 |
gnAgnLogFileSourceThe soure drawer of the alarm.ro Enumeration .1.3.6.1.4.1.2281.2.2.2.4.1.25 |
gnAgnLogFileTimeTThe time of the alarm represented by the number of seconds from 1.1.1970.ro INTEGER .1.3.6.1.4.1.2281.2.2.2.4.1.26 |
gnAgnLogFileHitlessSwitchLogAdminThis attribute allows for hitless logfile actions.rw Enumeration .1.3.6.1.4.1.2281.2.2.2.5 |
gnAgnLogFileXCSwitchLogAdminThis attribute allows for XC logfile actions.rw Enumeration .1.3.6.1.4.1.2281.2.2.2.6 |
gnAgnExternAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.3 |
gnAgnInExternAlarmTableThis table is the input external alarm table. SEQUENCE OF GnAgnInExternAlarmEntry .1.3.6.1.4.1.2281.2.2.3.1 |
gnAgnInExternAlarmEntryEntry containing the external alarm inputs. GnAgnInExternAlarmEntry .1.3.6.1.4.1.2281.2.2.3.1.1 |
gnAgnInExternAlarmDevIdThis value indicates device to which the external alarm
is connected - 1 Local, 2 Remotero Enumeration .1.3.6.1.4.1.2281.2.2.3.1.1.1 |
gnAgnInExternAlarmIndexThis value indicates the index of the input external alarm
1 to 8ro INTEGER .1.3.6.1.4.1.2281.2.2.3.1.1.2 |
gnAgnInExternAlarmEnableThis value indicates if this Input alarm is enabled.rw Enumeration .1.3.6.1.4.1.2281.2.2.3.1.1.3 |
gnAgnInExternAlarmTextThis field describes the external alarm. Max string 20 charactersrw DisplayString .1.3.6.1.4.1.2281.2.2.3.1.1.4 |
gnAgnInExternAlarmSeverityThis value indicates the severity of the external alarm
31 CRITICAL ,15 MAJOR, 7 MINOR, 3 WARNING and 1 EVENT.rw Enumeration .1.3.6.1.4.1.2281.2.2.3.1.1.5 |
gnAgnOutRelayAlarmTableThis table is the output relay alarm table. SEQUENCE OF GnAgnOutRelayAlarmEntry .1.3.6.1.4.1.2281.2.2.3.2 |
gnAgnOutRelayAlarmEntryEntry containing the output relay alarms. GnAgnOutRelayAlarmEntry .1.3.6.1.4.1.2281.2.2.3.2.1 |
gnAgnOutRelayAlarmDevIdThis value indicates device from which the relay is sent
from - 1 Local, 2 Remotero Enumeration .1.3.6.1.4.1.2281.2.2.3.2.1.1 |
gnAgnOutRelayAlarmIndexThis value indicates the index of the Output Relay alarm
1 to 5ro INTEGER .1.3.6.1.4.1.2281.2.2.3.2.1.2 |
gnAgnOutRelayAlarmTypeThis value indicates the alarm/led that causes
the relay to change its staterw Enumeration .1.3.6.1.4.1.2281.2.2.3.2.1.3 |
gnAgnFileTransfer OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.4 |
gnAgnFileTransferDestinationThe file destination. The file transfer destination will always be set to
1, LOCAL.rw Enumeration .1.3.6.1.4.1.2281.2.2.4.1 |
gnAgnFileTransferServerIPThe IP address of the server from which the file is loadedrw IpAddress .1.3.6.1.4.1.2281.2.2.4.2 |
gnAgnFileTransferFileNameThe name of the file to be loaded, format 8.3.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.2.4.3 |
gnAgnFileTransferTftpTotalTimeOutReceiving time-out value (seconds).rw INTEGER .1.3.6.1.4.1.2281.2.2.4.4 |
gnAgnFileTransferTransCmdThe command to be executed on fileName at fileServerIP.rw Enumeration .1.3.6.1.4.1.2281.2.2.4.5 |
gnAgnFileTransfertFtpStatusTftp session statusro Enumeration .1.3.6.1.4.1.2281.2.2.4.6 |
gnAgnFileTransfertftpBlockCountThe total number of blocks received in the current tFtp sessionro INTEGER .1.3.6.1.4.1.2281.2.2.4.7 |
gnAgnFileTransferProtocolFile transfer protocol: tftp or ftp.rw Enumeration .1.3.6.1.4.1.2281.2.2.4.8 |
gnAgnFileTransferUserNameUser name - only for ftp protocol.rw DisplayString .1.3.6.1.4.1.2281.2.2.4.9 |
gnAgnFileTransferPasswordPassword - only for ftp protocol.rw DisplayString .1.3.6.1.4.1.2281.2.2.4.10 |
gnAgnFileTransferIDCVersionControlPoints to the IDC software version to be downloadedro Enumeration .1.3.6.1.4.1.2281.2.2.4.11 |
gnAgnFileTransferODCVersionControlPoints to the ODC software version to be downloadedro Enumeration .1.3.6.1.4.1.2281.2.2.4.12 |
gnAgnInternalDownloadTableThis table controls the Internal Download process
from manager to MUX and ODU (local and remote). SEQUENCE OF GnAgnInternalDownloadEntry .1.3.6.1.4.1.2281.2.2.5 |
gnAgnInternalDownloadEntryEntry containing the internal download process controls, for local and
remote. GnAgnInternalDownloadEntry .1.3.6.1.4.1.2281.2.2.5.1 |
gnAgnInternalDownloadIdThis value indicates an index of a specific Internal Download
operation.ro INTEGER .1.3.6.1.4.1.2281.2.2.5.1.1 |
gnAgnInternalDownloadOperationThe Operation Descriptionro Enumeration .1.3.6.1.4.1.2281.2.2.5.1.2 |
gnAgnInternalDownloadActionThis parameter controls the download action operation.rw Enumeration .1.3.6.1.4.1.2281.2.2.5.1.3 |
gnAgnInternalDownloadStatusInternal download session statusro Enumeration .1.3.6.1.4.1.2281.2.2.5.1.4 |
gnAgnInternalDownloadBlockCountThe total number of blocks sent in the current session.ro INTEGER .1.3.6.1.4.1.2281.2.2.5.1.5 |
gnAgnInternalDownloadVersionControlPoints to the software version to be uploadedrw Enumeration .1.3.6.1.4.1.2281.2.2.5.1.6 |
gnAgnInternalDownloadFileSizeInBytesThe total number of blocks in the current filero INTEGER .1.3.6.1.4.1.2281.2.2.5.1.7 |
gnAgnInternalDownloadBytesCountThe number of bytes sent in the current sessionro INTEGER .1.3.6.1.4.1.2281.2.2.5.1.8 |
gnAgnInterLinkTableThis table controls the Inter Link Download process
between local and remote masters and between master and slave (local or
remote).
Each session transfers MUX, ODU or manager (IDC) software. SEQUENCE OF GnAgnInterLinkEntry .1.3.6.1.4.1.2281.2.2.6 |
gnAgnInterLinkEntryEntry containing the process controls for the interlink download
process, for local and remote. GnAgnInterLinkEntry .1.3.6.1.4.1.2281.2.2.6.1 |
gnAgnInterLinkIdThis value indicates the index of a specific InterLink
operation.ro INTEGER .1.3.6.1.4.1.2281.2.2.6.1.1 |
gnAgnInterLinkSideThe Link Sidero Enumeration .1.3.6.1.4.1.2281.2.2.6.1.2 |
gnAgnInterLinkSourceThe source distribution center.rw Enumeration .1.3.6.1.4.1.2281.2.2.6.1.3 |
gnAgnInterLinkDestinationThe destination distribution center.
The destination may be selected as the local IDU being contacted (me),
the collocated local IDU, in a protected configuration (mate) or
it may be selected to be the remote IDU.rw Enumeration .1.3.6.1.4.1.2281.2.2.6.1.4 |
gnAgnInterLinkSoftwareThe software type to be transferred. MUX, ODU or IDU (referred to as
manager).rw Enumeration .1.3.6.1.4.1.2281.2.2.6.1.5 |
gnAgnInterLinkActionThis parameter controls the interlink action operation.rw Enumeration .1.3.6.1.4.1.2281.2.2.6.1.6 |
gnAgnInterLinkStatusInter-link session statusro Enumeration .1.3.6.1.4.1.2281.2.2.6.1.7 |
gnAgnInterLinkBlockCountThe total number of blocks sent in the current session.ro INTEGER .1.3.6.1.4.1.2281.2.2.6.1.8 |
gnSoftwareVersionTableThis table contains the IDU, MUX, ODU & WS software versions;
local and remote. SEQUENCE OF GnSoftwareVersionEntry .1.3.6.1.4.1.2281.2.2.7 |
gnSoftwareVersionEntryEntry containing the currently operating IDU, ODU and MUX software
versions. GnSoftwareVersionEntry .1.3.6.1.4.1.2281.2.2.7.1 |
gnSoftwareVersionIdThe ID indicates which device is involved
in the specific row. The software table includes two rows,
one for the local radio and one for the remote radio.ro Enumeration .1.3.6.1.4.1.2281.2.2.7.1.1 |
gnSoftwareVersionIDUThis is the IDU software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.2 |
gnSoftwareVersionMUXThis is the MUX software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.3 |
gnSoftwareVersionODUThis is the ODU software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.4 |
gnSoftwareVersionIDUPostResetVersionThis is the IDU post reset software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.5 |
gnSoftwareVersionMUXPostResetVersionThis is the MUX post reset software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.6 |
gnSoftwareVersionODUPostResetVersionThis is the ODU post reset software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.7 |
gnSoftwareVersionMuxAlteraVerThis string contains the MUX altera versionsro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.8 |
gnSoftwareIDCVersionControlPoints to the software version that will run on the next resetrw Enumeration .1.3.6.1.4.1.2281.2.2.7.1.9 |
gnSoftwareVersionWSAlteraVerThis is the WS software versionro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.10 |
gnSoftwareVersionWSPostResetVersionThis is the WS post reset software versionro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.11 |
gnSoftwareVersionMrmcVerThis is the MRMC filter table software versionro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.12 |
gnSoftwareVersionMrmcPostResetVerThis is the MRMC filter table post reset software versionro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.13 |
gnSoftwareVersionBootSoftVerThis is the BOOT software versionro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.14 |
gnSoftwareVersionBootFlashVerThis is the BOOT FLASH versionro DisplayString .1.3.6.1.4.1.2281.2.2.7.1.15 |
gnAgnNTPCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.8 |
gnAgnNTPCfgServerIPThe IP address of the server from which
the current time is loaded.rw IpAddress .1.3.6.1.4.1.2281.2.2.8.1 |
gnAgnNTPCfgOffsetFromUTCThe offset from Coordinated Universal Time (minutes).
Possible values: -1439..1439.rw INTEGER (-1439..1439) .1.3.6.1.4.1.2281.2.2.8.2 |
gnAgnNTPCfgSummerAdjOffsetThe summer adjustment offset (minutes).
Possible values: -1439..1439.rw INTEGER (-1439..1439) .1.3.6.1.4.1.2281.2.2.8.3 |
gnAgnNTPCfgSummerAdjStartThe summertime adjustment start.
In order to set this value:
1.Turn every parameter (month, day, hour, minute)
to hexadecimal.
2.Write them all together - from left to right.
3.Turn the accepted number to decimal basis.
For example:
in order to set 11:27:1:55
1 = 0x01, 55 = 0x37
0x0b1b0137 = 186319159 (the last number is the one to set).rw INTEGER .1.3.6.1.4.1.2281.2.2.8.4 |
gnAgnNTPCfgSummerAdjEndThe summertime adjustment end.
In order to set this value:
1.Turn every parameter (month, day, hour, minute)
to hexadecimal.
2.Write them all together - from left to right.
3.Turn the accepted number to decimal basis.
For example:
in order to set 11:27:1:55
1 = 0x01, 55 = 0x37
0x0b1b0137 = 186319159 (the last number is the one to set).rw INTEGER .1.3.6.1.4.1.2281.2.2.8.5 |
gnAgnNTPCfgEnableAuthThis value indicates if the Authentication is enabled.rw Enumeration .1.3.6.1.4.1.2281.2.2.8.6 |
gnAgnNTPCfgAuthSecretKeyThe authentication secret key (HEX).
Not relevant when authentication is disable.rw OCTET STRING .1.3.6.1.4.1.2281.2.2.8.7 |
gnAgnNTPCfgAuthPublicKeyThe authentication public key is an integer number.
The valid values: 1-4294967295.
Not relevant when authentication is disable.rw Gauge .1.3.6.1.4.1.2281.2.2.8.8 |
gnAgnNTPCfgUpdateIntervalThe time interval between sending NTP requests
to the NTP server (minutes). Possible values: 1-65535.rw INTEGER .1.3.6.1.4.1.2281.2.2.8.9 |
gnAgnNTPCfgProtocolTyperw Enumeration .1.3.6.1.4.1.2281.2.2.8.10 |
gnAgnInBandMng OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.9 |
gnAgnInBandMngEthernetIpThe ethernet IP of the gateway network element.ro IpAddress .1.3.6.1.4.1.2281.2.2.9.1 |
gnAgnInBandMngEthernetMaskThe IP mask of the gateway network element.rw IpAddress .1.3.6.1.4.1.2281.2.2.9.2 |
gnAgnInBandMngPppIpThe PPP IP address of the gateway network element.ro IpAddress .1.3.6.1.4.1.2281.2.2.9.3 |
gnAgnInBandMngPppMaskThe PPP IP mask of the gateway network element.rw IpAddress .1.3.6.1.4.1.2281.2.2.9.4 |
gnAgnInBandMngDefRouteThe IP address of the default gateway/router
to the internet.rw IpAddress .1.3.6.1.4.1.2281.2.2.9.5 |
gnAgnInBandMngEnableEnable/Disable in-band management.rw Enumeration .1.3.6.1.4.1.2281.2.2.9.6 |
gnAgnInBandMngNetworkElementTypeThe element type of a single unit on the
inband network (Gateway or Network Element).rw Enumeration .1.3.6.1.4.1.2281.2.2.9.7 |
gnAgnInBandMngRadioChannelThe channel the in-band-management goes over
(DCCR\DCCM\etc.).rw Enumeration .1.3.6.1.4.1.2281.2.2.9.8 |
gnAgnInBandMngUnknownPacketsSelect if unknown packets will be transparently
transmitted over the RING or discarded and dropped.rw Enumeration .1.3.6.1.4.1.2281.2.2.9.9 |
gnAgnInBandMngTTLTime To Live.rw INTEGER .1.3.6.1.4.1.2281.2.2.9.10 |
gnAgnInBandMngRingIpSubnetThe IP subnet address of the ring.rw IpAddress .1.3.6.1.4.1.2281.2.2.9.11 |
gnAgnInBandMngRingIpMaskThe IP mask of the ring subnet address.rw IpAddress .1.3.6.1.4.1.2281.2.2.9.12 |
gnAgnInBandMngNetworkIdIdentification for single link path of
PPPoE over cross-networks.rw INTEGER .1.3.6.1.4.1.2281.2.2.9.13 |
gnAgnInBandMngLineModeEnable the user to force PPPoE mode
instead of DCCR line communication.rw Enumeration .1.3.6.1.4.1.2281.2.2.9.14 |
gnAgnInBandMngFiberChannelrw Enumeration .1.3.6.1.4.1.2281.2.2.9.15 |
gnAgnInBandMngTribChannelrw Enumeration .1.3.6.1.4.1.2281.2.2.9.16 |
gnAgnInBandMngXChannelTableThis table defines the inband channels mapping. SEQUENCE OF GnAgnInBandMngXChannelEntry .1.3.6.1.4.1.2281.2.2.9.17 |
gnAgnInBandMngXChannelEntryThis is an entry in the inband channel table.
This table contains a row for every channel (1..4).
First 3 physical channels are available in the 8 possible mapping options (on both carrier drawers).
An additional channel (4) is available on the IDC (PPPoE)). GnAgnInBandMngXChannelEntry .1.3.6.1.4.1.2281.2.2.9.17.1 |
gnAgnInBandMngXChannelIdThe channel Idro Enumeration .1.3.6.1.4.1.2281.2.2.9.17.1.1 |
gnAgnInBandMngXChannelIfIndexThe ifIndex of the interface that is mapped to this channelrw INTEGER .1.3.6.1.4.1.2281.2.2.9.17.1.2 |
gnAgnInBandMngXChannelTypeThe type of channel the in-band-management goes over.
Default value for channels 1 and 3 in the carrier drawers is Proprietary.
Channel 2 not allowed to be Proprietary.
In protection the ch_type of ch#3 can not be modified
Channel 4 must be PPPoErw Enumeration .1.3.6.1.4.1.2281.2.2.9.17.1.3 |
gnAgnInBandMngXChannelStateEnable/Disable the in band channelrw Enumeration .1.3.6.1.4.1.2281.2.2.9.17.1.4 |
gnAgnInBandMngXChannelNeighborIPThe PPP IP address of the gateway network element.rw IpAddress .1.3.6.1.4.1.2281.2.2.9.17.1.5 |
gnAgnInBandMngXChannelStatusThis MIB parameter defines the In-band PPP connection status.
If the MIB value is up the PPP connection is up and running
If the MIB value is down the PPP connection is down and is in initialization state.
(Trying to establish a connection)
If the MIB value is closed the PPP connection is down and is not trying open a connection.ro Enumeration .1.3.6.1.4.1.2281.2.2.9.17.1.6 |
gnAgnInBandMngXEnableInbandChannelsThis configuration enables/disables the in-band channels: 1-4.
The LSB represent channel 1, the 2nd bit channel 2, etc.
If a bit is on (1) it's channel is enabled.
Example: if channels 2 & 4 are enabled and channels 1 & 3 are disabled, then
the binary value is 1010, so the MIB value (decimal integer) will be 10.rw INTEGER .1.3.6.1.4.1.2281.2.2.9.18 |
gnAgnInBandMngMainGNEInterfacedetermines the primary GNE channel.
Default means fixed channel prioritizing, in the following order (from first to last):
Right Carrier Radio interface, [STM-1] Line interface on either Left or Right Carrier,
Left Carrier Radio interface and PPPoE interface.rw Enumeration .1.3.6.1.4.1.2281.2.2.9.19 |
gnNeighborIP OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.10 |
gnNeighborInBandTableThis table defines the IP addresses of the units that are connected Inband. SEQUENCE OF GnNeighborInBandEntry .1.3.6.1.4.1.2281.2.2.10.1 |
gnNeighborInBandEntryThis is an entry in the IP addresses of the units that are connected Inband.
This table contains a row for every interface which type is logically connected.
for example regenerator which is connected in band has two neighbors: the first (index 1)
the remote radio unit and the second the remote fiber neighbor (index 2). GnNeighborInBandEntry .1.3.6.1.4.1.2281.2.2.10.1.1 |
gnNeighborInBandIPThe PPP IP address of the gateway network element.rw IpAddress .1.3.6.1.4.1.2281.2.2.10.1.1.1 |
gnNeighborInBandStatusThis MIB parameter defines the In-band PPP connection status.
If the MIB value is up the PPP connection is up and running
If the MIB value is down the PPP connection is down and is in initialization state.
(Trying to establish a connection)
If the MIB value is closed the PPP connection is down and is not trying open a connection.ro Enumeration .1.3.6.1.4.1.2281.2.2.10.1.1.2 |
gnNeighborMateIPThe Protection Mate IP address.ro IpAddress .1.3.6.1.4.1.2281.2.2.10.2 |
gnNeighborRemoteRadioIPThe IP address of the Radio Remote IDU.ro IpAddress .1.3.6.1.4.1.2281.2.2.10.3 |
gnNeighborInBandXTableThis table defines the IP addresses of the units that are connected Inband. SEQUENCE OF GnNeighborInBandXEntry .1.3.6.1.4.1.2281.2.2.10.4 |
gnNeighborInBandXEntryThis is an entry in the IP addresses of the units that are connected Inband.
This table contains a row for every interface which type is logically connected.
for example regenerator which is connected in band has two neighbors: the first (index 1)
the remote radio unit and the second the remote fiber neighbor (index 2). GnNeighborInBandXEntry .1.3.6.1.4.1.2281.2.2.10.4.1 |
gnNeighborInBandXIdro Enumeration .1.3.6.1.4.1.2281.2.2.10.4.1.1 |
gnNeighborInBandXIPThe PPP IP address of the gateway network element.rw IpAddress .1.3.6.1.4.1.2281.2.2.10.4.1.2 |
gnNeighborIpTableThis table shows the Neighbor IP for each STM connection. SEQUENCE OF GnNeighborIpEntry .1.3.6.1.4.1.2281.2.2.10.5 |
gnNeighborIpEntry. GnNeighborIpEntry .1.3.6.1.4.1.2281.2.2.10.5.1 |
gnNeighborIpDetectModeThe Neighbor detect can be done automatically or to be manually insreted.
Disable marks that the IP Detect is not used.rw Enumeration .1.3.6.1.4.1.2281.2.2.10.5.1.1 |
gnNeighborIpAddressThe neighbor IP address.rw IpAddress .1.3.6.1.4.1.2281.2.2.10.5.1.2 |
gnNeighborIpRemoteIfIndexThe If index of the neighbor IP address connected to the current If Index.rw INTEGER .1.3.6.1.4.1.2281.2.2.10.5.1.3 |
gnNeighborIpRemoteTypeThe Type of the neighbor.rw Enumeration .1.3.6.1.4.1.2281.2.2.10.5.1.4 |
gnAgnSNMPCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.11 |
gnAgnSNMPCfgTrapCommunityrw OCTET STRING .1.3.6.1.4.1.2281.2.2.11.1 |
gnAgnSNMPCfgReadCommunityrw OCTET STRING .1.3.6.1.4.1.2281.2.2.11.2 |
gnAgnSNMPCfgWriteCommunityrw OCTET STRING .1.3.6.1.4.1.2281.2.2.11.3 |
gnAgnPrvt OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.12 |
gnAgnPrvtCmd.rw Enumeration .1.3.6.1.4.1.2281.2.2.12.1 |
gnAgnPrvtCmdStat.ro Enumeration .1.3.6.1.4.1.2281.2.2.12.2 |
gnSoftwareDrawerVersionTableThis table contains the IDU, MUX & ODU software versions;
local and remote. SEQUENCE OF GnSoftwareDrawerVersionEntry .1.3.6.1.4.1.2281.2.2.13 |
gnSoftwareDrawerVersionEntryEntry containing the currently operating IDU, ODU and MUX software
versions. GnSoftwareDrawerVersionEntry .1.3.6.1.4.1.2281.2.2.13.1 |
gnSoftwareDrawerIdThe ID indicates which Drawer is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.2.2.13.1.1 |
gnSoftwareDrawerVersionMUXThis is the MUX software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.2 |
gnSoftwareDrawerVersionMUXPostResetVersionThis is the ODU software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.3 |
gnSoftwareDrawerVersionODUThis is the MUX post reset software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.4 |
gnSoftwareDrawerVersionODUPostResetVersionThis is the MUX post reset software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.5 |
gnSoftwareDrawerVersionModemFileThis is the Modem software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.6 |
gnSoftwareDrawerVersionModemFilePostResetVersionThis is the Modem post reset software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.7 |
gnSoftwareDrawerVersionModemScriptThis is the Modem software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.8 |
gnSoftwareDrawerVersionModemScriptPostResetVersionThis is the Modem post reset software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.9 |
gnSoftwareDrawerVersionRfuFpgaVersionThis is the Rfu Fpga software version.ro DisplayString .1.3.6.1.4.1.2281.2.2.13.1.10 |
gnAgnCurrentAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.14 |
gnAgnCurrentAlarmLastChangeThis counter initialized with random number after resest, and incremented on each change in the gnAgnCurrentAlarmTable
(either add or remove of an entery).ro INTEGER .1.3.6.1.4.1.2281.2.2.14.1 |
gnAgnCurrentAlarmTableThis table includes the currently open alarm (when a RAISED trap is
sent, an alarm is added to the table, when a CLEAR trap is sent,
the alarm is removed. SEQUENCE OF GnCurrentAlarmEntry .1.3.6.1.4.1.2281.2.2.14.2 |
gnCurrentAlarmEntryEntry containing the info of a currently RAISED trap. GnCurrentAlarmEntry .1.3.6.1.4.1.2281.2.2.14.2.1 |
gnAgnCurrentAlarmCounterA running counter of open alarm, the counter is incremented on every new RAISED trap.
It is cleared after reset. This counter is (optionaly) attached to each trap.ro INTEGER .1.3.6.1.4.1.2281.2.2.14.2.1.1 |
gnAgnCurrentAlarmSeverityThe current Alarm severityro Enumeration .1.3.6.1.4.1.2281.2.2.14.2.1.2 |
gnAgnCurrentAlarmIdAlarm Identifier (contains alarm type and interface). Same AlarmId for rasie and clear alarms.ro INTEGER .1.3.6.1.4.1.2281.2.2.14.2.1.3 |
gnAgnCurrentAlarmIfIndexInterface Index where the alarm occurred, alarms that are
not associated with specific interface will have the following value:
For IDC related alarms the value is: 65001
For drawer1 related alarms the value is: 65003
For drawer2 related alarms the value is: 65004
If Alarm's origin is bigger than 256, it will be 65000 + the originro INTEGER .1.3.6.1.4.1.2281.2.2.14.2.1.4 |
gnAgnCurrentAlarmOriginThe origin drawer of the alarm (if applicable, otherwise it will be idc(2)).ro Enumeration .1.3.6.1.4.1.2281.2.2.14.2.1.5 |
gnAgnCurrentAlarmUnitThe unit of the alarm.ro Enumeration .1.3.6.1.4.1.2281.2.2.14.2.1.6 |
gnAgnCurrentAlarmTrapIDThe ID of the RAISED trap that was sent when this alarm was raised.ro INTEGER .1.3.6.1.4.1.2281.2.2.14.2.1.7 |
gnAgnCurrentAlarmTimeTTimestamp of this alarm, this number is the seconds from midnight 1.1.1970.ro INTEGER .1.3.6.1.4.1.2281.2.2.14.2.1.8 |
gnAgnCurrentAlarmTextThe alarm display text (same as the text in the sent trap).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.2.2.14.2.1.9 |
gnNMS OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.15 |
gnApplicFileTableThis table contains the application file list. SEQUENCE OF GnApplicFileEntry .1.3.6.1.4.1.2281.2.2.16 |
gnApplicFileEntryEntry containing the application file list. GnApplicFileEntry .1.3.6.1.4.1.2281.2.2.16.1 |
gnApplicFileIdThe ID indicates which device is involved
in the specific row. The application file table includes two rows,
one for the local radio and one for the remote radio.ro INTEGER .1.3.6.1.4.1.2281.2.2.16.1.1 |
gnApplicFileNameThis is the application file name.ro DisplayString .1.3.6.1.4.1.2281.2.2.16.1.2 |
gnApplicFileVersionThis is the application file version.ro DisplayString .1.3.6.1.4.1.2281.2.2.16.1.3 |
gnApplicFileCreateDateThis parameter specifies the application file download date
Format 'YYYY-MM-DD,HH:MM:SS' (Hexadecimal).
A date-time specification.
field octets contents range
-
1 1-2 year 0..65536
2 3 month 1..12
3 4 day 1..31
4 5 hour 0..23
5 6 minutes 0..59
6 7 seconds 0..60
(use 60 for leap-second)
7 8 deci-seconds 0..9
8 9 direction from UTC '+' / '-'
9 10 hours from UTC 0..11
10 11 minutes from UTC 0..59
For example, Tuesday May 26, 1992 at 1:30:15 PM EDT
would be displayed as: 07 c8 05 1a 0d 1e 0f 00
( 1992 -5 -26,13:30:15 )
Note that if only local time is known, then timezone
information (fields 8-10) is not present.ro OCTET STRING .1.3.6.1.4.1.2281.2.2.16.1.4 |
gnApplicFileDownloadDateThis parameter specifies the application file download date
Format 'YYYY-MM-DD,HH:MM:SS' (Hexadecimal).
A date-time specification.
field octets contents range
-
1 1-2 year 0..65536
2 3 month 1..12
3 4 day 1..31
4 5 hour 0..23
5 6 minutes 0..59
6 7 seconds 0..60
(use 60 for leap-second)
7 8 deci-seconds 0..9
8 9 direction from UTC '+' / '-'
9 10 hours from UTC 0..11
10 11 minutes from UTC 0..59
For example, Tuesday May 26, 1992 at 1:30:15 PM EDT
would be displayed as: 07 c8 05 1a 0d 1e 0f 00
( 1992 -5 -26,13:30:15 )
Note that if only local time is known, then timezone
information (fields 8-10) is not present.ro OCTET STRING .1.3.6.1.4.1.2281.2.2.16.1.5 |
gnApplicFileTypeThis is the application file type.ro Enumeration .1.3.6.1.4.1.2281.2.2.16.1.6 |
gnApplicFileSubTypeThis is the application file sub type.ro DisplayString .1.3.6.1.4.1.2281.2.2.16.1.7 |
gnApplicFileFirmwareThis is the application file firmware.ro INTEGER .1.3.6.1.4.1.2281.2.2.16.1.8 |
gnApplicFileGeneralPurposeThis is the application file General Purpose.ro INTEGER .1.3.6.1.4.1.2281.2.2.16.1.9 |
gnApplicFileSizeThis is the application file size in bytes.ro INTEGER .1.3.6.1.4.1.2281.2.2.16.1.10 |
gnApplicFileCompressedThis is indicate the application file compress status.ro Enumeration .1.3.6.1.4.1.2281.2.2.16.1.11 |
gnApplicFileDssSupportThis is indicate the application file DSS support.ro Enumeration .1.3.6.1.4.1.2281.2.2.16.1.12 |
gnApplicFileCrcSupportThis is indicate the application file CRC support.ro Enumeration .1.3.6.1.4.1.2281.2.2.16.1.13 |
gnDiskCapacityData OBJECT IDENTIFIER .1.3.6.1.4.1.2281.2.2.17 |
gnDiskUsedspaceThe ID indicates Disk Used space.ro INTEGER .1.3.6.1.4.1.2281.2.2.17.1 |
gnDiskFreespaceThe ID indicates Disk Free space.ro INTEGER .1.3.6.1.4.1.2281.2.2.17.2 |
gnUnits OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3 |
gnODU OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.1 |
gnOduCfgTableThis table defines the configuration of the Outdoor part
of the system. SEQUENCE OF GnOduCfgEntry .1.3.6.1.4.1.2281.3.1.1 |
gnOduCfgEntryThis is an entry in the ODU Configuration Table. This table
contains two rows, indexed by ifIndex= 1 for local ODU and
ifIndex = 101 for remote ODU. GnOduCfgEntry .1.3.6.1.4.1.2281.3.1.1.1 |
gnOduCfgTransmitterFrequencyThis parameter indicates the radio TX channel number.
WRITE will change the LOCAL side only.
Not all radios will support TX frequency change via channel numbers.rw INTEGER .1.3.6.1.4.1.2281.3.1.1.1.1 |
gnOduCfgRLPerfMonThresh1When the Received Level (RL) exceeds this threshold a
performance monitoring RL1 counter increments.rw INTEGER (-75..-15) .1.3.6.1.4.1.2281.3.1.1.1.2 |
gnOduCfgRLPerfMonThresh2When the Received Level (RL) exceeds this threshold a
performance monitoring RL2 counter increments.rw INTEGER (-75..-15) .1.3.6.1.4.1.2281.3.1.1.1.3 |
gnOduCfgATPCStatusThis parameter indicates if the ATPC option is enabled or disabled.rw Enumeration .1.3.6.1.4.1.2281.3.1.1.1.4 |
gnOduCfgMUTEStatusThis parameter indicates if transmitter will be in mute state.
(Mute on -> don't transmit)rw Enumeration .1.3.6.1.4.1.2281.3.1.1.1.5 |
gnOduCfgAntennaTypeThis parameter indicates the size of the antenna used
in the ODU. This attribute will not auto-detect the antenna size.
It is used for the unfaded RSL calculation feature included in
CERAGONView.rw Enumeration .1.3.6.1.4.1.2281.3.1.1.1.6 |
gnOduCfgTransmitLevelThis is the transmitter output power level of the signal
transmitted by the radios, displayed in DBM.rw INTEGER (-50..30) .1.3.6.1.4.1.2281.3.1.1.1.7 |
gnOduCfgRealTxFreqNumberIdentifies the RF Tx frequency. For 6, 7 and 8 bands the Tx frequency
resolution is in kHz, for other bands the resolution is in 10kHz.
If the Tx frequency value is over 4000000 than the band is identified
as 6, 7 or 8G band.rw INTEGER .1.3.6.1.4.1.2281.3.1.1.1.8 |
gnOduCfgRealRxFreqNumberIdentifies the RF Rx frequency. For 6, 7 and 8 bands the Rx frequency
resolution is in kHz, for other bands the resolution is in 10kHz.
If the Rx frequency value is over 4000000 than the band is identified
as 6, 7 or 8G band.rw INTEGER .1.3.6.1.4.1.2281.3.1.1.1.9 |
gnOduCfgMinTxFreqNumberThis the Minimum TX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.1.1.10 |
gnOduCfgMaxTxFreqNumberThis the Maximum TX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.1.1.11 |
gnOduCfgMaxTxLevelThis is the theoretical maximum level that this ODU unit
can transmit.ro INTEGER .1.3.6.1.4.1.2281.3.1.1.1.12 |
gnOduCfgRefRslThis is the received level reference, applicable when utilizing ATPC mode;
displayed in dBm.rw INTEGER (-70..-30) .1.3.6.1.4.1.2281.3.1.1.1.13 |
gnOduCfgForceRmtMuteTxWhen on, this parameter force the transmitter to be in mute state.
(Mute on -> don't transmit)rw Enumeration .1.3.6.1.4.1.2281.3.1.1.1.14 |
gnOduCfgForceRmtMaxTxThis parameter force the transmitter output power level of the signal
transmitted by the radio.rw INTEGER (-50..30) .1.3.6.1.4.1.2281.3.1.1.1.15 |
gnOduCfgTLPerfMonThresh1When the Transmitted Level (TL) exceeds this threshold a
performance monitoring TL1 counter increments.rw INTEGER (-10..25) .1.3.6.1.4.1.2281.3.1.1.1.16 |
gnOduCfgMinRxFreqNumberThis the Minimum RX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.1.1.17 |
gnOduCfgMaxRxFreqNumberThis the Maximum RX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.1.1.18 |
gnOduCfgOduLoopSupportIndication for loopback support by the connected ODU.ro Enumeration .1.3.6.1.4.1.2281.3.1.1.1.19 |
gnOduCfgOduModel.ro Enumeration .1.3.6.1.4.1.2281.3.1.1.1.20 |
gnOduCfgFreqPlanStandardFor the NMS use.rw DisplayString .1.3.6.1.4.1.2281.3.1.1.1.21 |
gnOduCfgFreqDeviderIndicates the number with which we should divide the MIB Freq value to get to the actual Freq (100 or 1000)ro INTEGER .1.3.6.1.4.1.2281.3.1.1.1.22 |
gnOduStatusTableThis table defines the status of the Outdoor unit
of the system. SEQUENCE OF GnOduStatusEntry .1.3.6.1.4.1.2281.3.1.2 |
gnOduStatusEntryThis is an entry in the ODU Status Table. This table
contains two rows, indexed by ifIndex= 1 for local ODU and
ifIndex = 101 for remote ODU. GnOduStatusEntry .1.3.6.1.4.1.2281.3.1.2.1 |
gnOduStatusCelsiusTempThis is the temperature of the ODU in degrees Celsius.ro INTEGER (-50..80) .1.3.6.1.4.1.2281.3.1.2.1.1 |
gnOduStatusFahrenheitTempThis is the temperature of the ODU in degrees Fahrenheit.ro INTEGER (-58..176) .1.3.6.1.4.1.2281.3.1.2.1.2 |
gnOduStatusTransmitLevelThis is the transmit level of the signal transmitted by the radios
transmitter, displayed in DBM.ro INTEGER (-99..30) .1.3.6.1.4.1.2281.3.1.2.1.3 |
gnOduStatusReceiveLevelThis is the receive level of the signal transmitted by the radios
transmitter, displayed in DBM.ro INTEGER (-99..-15) .1.3.6.1.4.1.2281.3.1.2.1.4 |
gnOduStatusSynthesizerVCOLockThis octet represents the ODU status as follows (bit 1, LSB):
bit 1 on = TX IF synthesizer
bit 2 on = RX IF synthesizer
bit 3 on = Xband synthesizer
bit 4 on = History TX IF synthesizer
bit 5 on = History RX IF synthesizer
bit 6 on = History Xband synthesizerro OCTET STRING .1.3.6.1.4.1.2281.3.1.2.1.5 |
gnOduStatusPowerSupplyThis octet represents the status of the power
supplies of the ODU:
bit 1 on = +5V faulty
bit 2 on = +8V faulty
bit 3 on = +12V faulty
bit 4 on = -12V faulty.ro OCTET STRING .1.3.6.1.4.1.2281.3.1.2.1.6 |
gnOduStatusClearLoopTimerThis variable indicates the remaining time (in minutes)
till the relevant odu loopback timer will be expired.
when starting a loopback and the value of gnGenCfgClearLoopTimeout is x,
the gnOduStatusClearLoopTimer will be also x, after one minute it will be x-1, etc.ro INTEGER .1.3.6.1.4.1.2281.3.1.2.1.7 |
gnOduMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.1.3 |
gnOduMonCurrTableThis table defines/keeps the counters of the current 15 min interval. SEQUENCE OF GnOduMonCurrEntry .1.3.6.1.4.1.2281.3.1.3.1 |
gnOduMonCurrEntryThis is an entry in the Current Interval Table. This table
contains two rows, indexed by ifIndex= 1 for local ODU and
ifIndex = 101 for remote ODU. GnOduMonCurrEntry .1.3.6.1.4.1.2281.3.1.3.1.1 |
gnOduMonCurrMinRLThe minimum received signal level (RL) in the current 15 minute interval.
(in DBM)ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.1 |
gnOduMonCurrMaxRLThe maximum received signal level (RL) in the current 15 minute interval.
(in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.2 |
gnOduMonCurrTLThresh1ExceedThe number of seconds TL exceeded the TL1
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.3.1.1.3 |
gnOduMonCurrRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.3.1.1.4 |
gnOduMonCurrRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.3.1.1.5 |
gnOduMonCurrDayMinRLThe minimum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.6 |
gnOduMonCurrDayMaxRLThe maximum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.7 |
gnOduMonCurrDayTLThresh1ExceedThe number of seconds TL exceeded the TL1 threshold
in the last 24 hours.ro Counter .1.3.6.1.4.1.2281.3.1.3.1.1.8 |
gnOduMonCurrDayRLThresh1ExceedThe number of seconds RL exceeded the RL1 threshold
in the last 24 hours.ro Counter .1.3.6.1.4.1.2281.3.1.3.1.1.9 |
gnOduMonCurrDayRLThresh2ExceedThe number of seconds RL exceeded the RL2 threshold
in the last 24 hours.ro Counter .1.3.6.1.4.1.2281.3.1.3.1.1.10 |
gnOduMonCurrMinTLThe minimum transmitted signal level (TL) in the current 15 minute interval.
(in DBM)ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.11 |
gnOduMonCurrMaxTLThe maximum transmitted signal level (TL) in the current 15 minute interval.
(in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.12 |
gnOduMonCurrDayMinTLThe minimum Transmitted Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.13 |
gnOduMonCurrDayMaxTLThe maximum Transmitted Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.1.1.14 |
gnOduMonIntervalTableThis table defines/keeps the counters of the 96 last intervals of 15 min. SEQUENCE OF GnOduMonIntervalEntry .1.3.6.1.4.1.2281.3.1.3.2 |
gnOduMonIntervalEntryThis is an entry in the Interval Table. This table
is indexed by ifIndex= 1 for local ODU and
ifIndex = 101 for remote ODU and by interval idx GnOduMonIntervalEntry .1.3.6.1.4.1.2281.3.1.3.2.1 |
gnOduMonIntervalIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.2.1.1 |
gnOduMonIntervalMinRLThe minimum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.3.2.1.2 |
gnOduMonIntervalMaxRLThe maximum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.3.2.1.3 |
gnOduMonIntervalTLThresh1ExceedThe number of seconds TL exceeded the TL1
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.3.2.1.4 |
gnOduMonIntervalEventEvents
bit 1 = CommDisc.
bit 2 = CommCon
bit 3 = ATPC2Max.
bit 4 = ATPC2Norm.
Included for future development, not currently supported.ro OCTET STRING .1.3.6.1.4.1.2281.3.1.3.2.1.5 |
gnOduMonIntervalRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.3.2.1.6 |
gnOduMonIntervalRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.3.2.1.7 |
gnOduMonIntervalMinTLThe minimum TL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.3.2.1.8 |
gnOduMonIntervalMaxTLThe maximum TL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.3.2.1.9 |
gnOduMonDayTableThis table defines/keeps the counters of 96 intervals of 15 min. SEQUENCE OF GnOduMonDayEntry .1.3.6.1.4.1.2281.3.1.3.3 |
gnOduMonDayEntryThis is an entry in the Days Table. This table
is indexed by ifIndex= 1 for local ODU and
ifIndex = 101 for remote ODU and by day idx.
gnOduMonDayIdx = 1 is one day from now,
gnOduMonDayIdx = 2 is two days from now, and so on... GnOduMonDayEntry .1.3.6.1.4.1.2281.3.1.3.3.1 |
gnOduMonDayIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.3.1.1 |
gnOduMonDayMinRLThe minimum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.3.1.2 |
gnOduMonDayMaxRLThe maximum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.3.1.3 |
gnOduMonDayTLThresh1ExceedThe number of seconds TL exceeded the TL1 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.3.3.1.4 |
gnOduMonDayRLThresh1ExceedThe number of seconds RL exceeded the RL1 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.3.3.1.5 |
gnOduMonDayRLThresh2ExceedThe number of seconds RL exceeded the RL2 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.3.3.1.6 |
gnOduMonDayMinTLThe minimum Transmit Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.3.1.7 |
gnOduMonDayMaxTLThe maximum Transmit Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.3.3.1.8 |
gnOduCfgXTableThis table defines the configuration of the Outdoor part
of the system. SEQUENCE OF GnOduCfgXEntry .1.3.6.1.4.1.2281.3.1.4 |
gnOduCfgXEntryThis is an entry in the ODU Configuration Table. This table
contains two rows, indexed by gnOduCfgXId= 3 for drawer1 ODU and
gnOduCfgXId = 4 for drawer2 ODU. GnOduCfgXEntry .1.3.6.1.4.1.2281.3.1.4.1 |
gnOduCfgXIdro Enumeration .1.3.6.1.4.1.2281.3.1.4.1.1 |
gnOduCfgXTxFreqNumLocalRemoteIndicates the radio transmit frequency, displayed in
1/100 MHz. WRITE changes the local and remote sides. Only for systems that
support frequency configuration (Not channel).rw INTEGER .1.3.6.1.4.1.2281.3.1.4.1.2 |
gnOduCfgXRLPerfMonThresh1When the Received Level (RL) exceeds this threshold a
performance monitoring RL1 counter increments.rw INTEGER (-75..-15) .1.3.6.1.4.1.2281.3.1.4.1.3 |
gnOduCfgXRLPerfMonThresh2When the Received Level (RL) exceeds this threshold a
performance monitoring RL2 counter increments.rw INTEGER (-75..-15) .1.3.6.1.4.1.2281.3.1.4.1.4 |
gnOduCfgXATPCStatusThis parameter indicates if the ATPC option is enabled or disabled.rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.5 |
gnOduCfgXMUTEStatusThis parameter indicates if transmitter will be in mute state.
(Mute on -> don't transmit)rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.6 |
gnOduCfgXAntennaTypeThis parameter indicates the size of the antenna used
in the ODU. This attribute will not auto-detect the antenna size.
It is used for the unfaded RSL calculation feature included in
CERAGONView.rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.7 |
gnOduCfgXTransmitLevelThis is the transmitter output power level of the signal
transmitted by the radios, displayed in DBM.rw INTEGER (-50..34) .1.3.6.1.4.1.2281.3.1.4.1.8 |
gnOduCfgXRealTxFreqNumberIdentifies the RF Tx frequency. For 6, 7 and 8 bands the Tx frequency
resolution is in kHz, for other bands the resolution is in 10kHz.
If the Tx frequency value is over 4000000 than the band is identified
as 6, 7 or 8G band.rw INTEGER .1.3.6.1.4.1.2281.3.1.4.1.9 |
gnOduCfgXRealRxFreqNumberIdentifies the RF Rx frequency. For 6, 7 and 8 bands the Rx frequency
resolution is in kHz, for other bands the resolution is in 10kHz.
If the Rx frequency value is over 4000000 than the band is identified
as 6, 7 or 8G band.rw INTEGER .1.3.6.1.4.1.2281.3.1.4.1.10 |
gnOduCfgXMinTxFreqNumberThis the Minimum TX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.4.1.11 |
gnOduCfgXMaxTxFreqNumberThis the Maximum TX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.4.1.12 |
gnOduCfgXMaxTxLevelThis is the theoretical maximum level that this ODU unit
can transmit.ro INTEGER .1.3.6.1.4.1.2281.3.1.4.1.13 |
gnOduCfgXRefRslThis is the received level reference, applicable when utilizing ATPC mode;
displayed in dBm.rw INTEGER (-70..-30) .1.3.6.1.4.1.2281.3.1.4.1.14 |
gnOduCfgXForceRmtMuteTxWhen on, this parameter force the transmitter to be in mute state.
(Mute on -> don't transmit)rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.15 |
gnOduCfgXForceRmtMaxTxThis parameter force the transmitter output power level of the signal
transmitted by the radio.rw INTEGER (-50..30) .1.3.6.1.4.1.2281.3.1.4.1.16 |
gnOduCfgXTLPerfMonThresh1When the Transmitted Level (TL) exceeds this threshold a
performance monitoring TL1 counter increments.rw INTEGER (-10..25) .1.3.6.1.4.1.2281.3.1.4.1.17 |
gnOduCfgXOperationThis parameter allows to perform ODU operations.
(3) will SET all ODU default configurations.
(4) will implement ODU reset.rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.18 |
gnOduCfgXODUSerialNumberThis is the ODU serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.3.1.4.1.19 |
gnOduCfgXChannelBandwidthThe TX channel bandwidth, displayed in 1/100 MHz.
For example:
An STM-1 ETSI TX channel bandwidth of 56MHz is displayed as the value 5600.ro INTEGER .1.3.6.1.4.1.2281.3.1.4.1.20 |
gnOduCfgXMinRxFreqNumberThis the Minimum RX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.4.1.21 |
gnOduCfgXMaxRxFreqNumberThis the Maximum RX frequency that the ODU can receive - Used by the
management station.ro INTEGER .1.3.6.1.4.1.2281.3.1.4.1.22 |
gnOduCfgXRxFreqNumLocalRemoteIndicates the radio transmit frequency, displayed in
1/100 MHz. WRITE changes the local and remote sides. Only for systems that
support frequency configuration (Not channel).rw INTEGER .1.3.6.1.4.1.2281.3.1.4.1.23 |
gnOduCfgXOduLoopSupportInidcation for loopback support by the connected ODU.ro Enumeration .1.3.6.1.4.1.2281.3.1.4.1.24 |
gnOduCfgXOduModel.ro Enumeration .1.3.6.1.4.1.2281.3.1.4.1.25 |
gnOduCfgXFreqPlanStandardFor the NMS use.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2281.3.1.4.1.26 |
gnOduCfgXFreqDeviderIndicates the number with which we should divide the MIB Freq value to get to the actual Freq (100 or 1000)ro INTEGER .1.3.6.1.4.1.2281.3.1.4.1.27 |
gnOduCfgXLoopbackOptionThis parameter enable the user to activate an ODU loopback .rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.28 |
gnOduCfgXxpicClockModeThis is the status of the xpic clock mode.ro Enumeration .1.3.6.1.4.1.2281.3.1.4.1.29 |
gnOduCfgXUnfadedReferenceRslThis is used for the unfaded RSL calculation feature included in
CERAGONView.rw INTEGER (-70..-15) .1.3.6.1.4.1.2281.3.1.4.1.30 |
gnOduCfgXRfuModeThe RX mode of operation.rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.31 |
gnOduCfgXRslRouteToConnectorChoose the receive level signal for the RSL connector.rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.32 |
gnOduCfgXDelayCalibrationOperationThis parameter enables launching a delay calibration parameters calculation.rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.33 |
gnOduCfgXDelayCalibrationValueThis parameter indicates the delay calibration result and delay calibration override value.
values are between -130 to 130.rw INTEGER (-130..130) .1.3.6.1.4.1.2281.3.1.4.1.34 |
gnOduCfgXDelayCalibrationWgTypeDelay Calibration WG Type For the NMS use.rw DisplayString .1.3.6.1.4.1.2281.3.1.4.1.35 |
gnOduCfgXOduLogThis parameter enable the user to activate ODU log.rw Enumeration .1.3.6.1.4.1.2281.3.1.4.1.36 |
gnOduCfgXOduLogPeriodThis parameter enable the user to chose the log peroid (in sec).rw INTEGER .1.3.6.1.4.1.2281.3.1.4.1.37 |
gnOduCfgXXpiPerfMonThreshWhen the Received XPI beneath this threshold a
performance monitoring XPI counter increments (future develope).rw INTEGER .1.3.6.1.4.1.2281.3.1.4.1.38 |
gnOduStatusXTableThis table defines the status of the Outdoor unit
of the system. SEQUENCE OF GnOduStatusXEntry .1.3.6.1.4.1.2281.3.1.5 |
gnOduStatusXEntryThis is an entry in the ODU Status Table. This table
contains two rows, indexed by gnOduStatusXId= 3 for drawer1 ODU
and gnOduStatusXId = 4 for drawer2 ODU. GnOduStatusXEntry .1.3.6.1.4.1.2281.3.1.5.1 |
gnOduStatusXIdro Enumeration .1.3.6.1.4.1.2281.3.1.5.1.1 |
gnOduStatusXCelsiusTempThis is the temperature of the ODU in degrees Celsius.ro INTEGER (-70..80) .1.3.6.1.4.1.2281.3.1.5.1.2 |
gnOduStatusXFahrenheitTempThis is the temperature of the ODU in degrees Fahrenheit.ro INTEGER (-58..176) .1.3.6.1.4.1.2281.3.1.5.1.3 |
gnOduStatusXTransmitLevelThis is the transmit level of the signal transmitted by the radios
transmitter, displayed in DBM.ro INTEGER (-99..34) .1.3.6.1.4.1.2281.3.1.5.1.4 |
gnOduStatusXReceiveLevelThis is the receive level of the signal transmitted by the radios
transmitter, displayed in DBM.ro INTEGER (-99..-15) .1.3.6.1.4.1.2281.3.1.5.1.5 |
gnOduStatusXSynthesizerVCOLockThis octet represents the ODU status as follows (bit 1, LSB):
bit 1 on = TX IF synthesizer
bit 2 on = RX IF synthesizer
bit 3 on = Xband synthesizer
bit 4 on = History TX IF synthesizer
bit 5 on = History RX IF synthesizer
bit 6 on = History Xband synthesizerro OCTET STRING .1.3.6.1.4.1.2281.3.1.5.1.6 |
gnOduStatusXPowerSupplyThis octet represents the status of the power
supplies of the ODU:
bit 1 on = +5V faulty
bit 2 on = +8V faulty
bit 3 on = +12V faulty
bit 4 on = -12V faulty.ro OCTET STRING .1.3.6.1.4.1.2281.3.1.5.1.7 |
gnOduStatusXIfcSupportedIndication for IFC support.ro Enumeration .1.3.6.1.4.1.2281.3.1.5.1.8 |
gnOduStatusXRslDiversityThis is the receive level of the space diversity signal, displayed in DBM.ro INTEGER (-99..0) .1.3.6.1.4.1.2281.3.1.5.1.9 |
gnOduStatusXRslCombinedThis is the receive level of the combined signal, displayed in DBM.ro INTEGER (-99..0) .1.3.6.1.4.1.2281.3.1.5.1.10 |
gnOduStatusXRfuAddressThe RFU Address.ro INTEGER .1.3.6.1.4.1.2281.3.1.5.1.11 |
gnOduStatusXMinTransmitLevelThis is the minimum transmit level of the signal transmitted by the radios
transmitter, displayed in DBM.. (for RFU unit only)ro INTEGER (-50..34) .1.3.6.1.4.1.2281.3.1.5.1.12 |
gnOduStatusXOduSWVerThis is the ODU software version.ro DisplayString .1.3.6.1.4.1.2281.3.1.5.1.13 |
gnOduStatusXOduSWPostVerThis is the ODU post reset software version.ro DisplayString .1.3.6.1.4.1.2281.3.1.5.1.14 |
gnOduStatusXRfuFwVerThis is the RFU FW version.ro DisplayString .1.3.6.1.4.1.2281.3.1.5.1.15 |
gnOduStatusXValidIntervalsThe number of previous valid intervals for which valid data has been stored
for the specific ODU.ro INTEGER .1.3.6.1.4.1.2281.3.1.5.1.16 |
gnOduMonitorX OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.1.6 |
gnOduMonCurrXTableThis table defines/keeps the counters of the current 15 min interval. SEQUENCE OF GnOduMonCurrXEntry .1.3.6.1.4.1.2281.3.1.6.1 |
gnOduMonCurrXEntryThis is an entry in the Current Interval Table. This table
contains two rows, indexed by gnOduMonCurrXId= 3 for drawer1 ODU and
gnOduMonCurrXId = 4 for drawer2 ODU. GnOduMonCurrXEntry .1.3.6.1.4.1.2281.3.1.6.1.1 |
gnOduMonCurrXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.1.1.1 |
gnOduMonCurrXMinRLThe minimum received signal level (RL) in the current 15 minute interval.
(in DBM)ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.2 |
gnOduMonCurrXMaxRLThe maximum received signal level (RL) in the current 15 minute interval.
(in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.3 |
gnOduMonCurrXTLThresh1ExceedThe number of seconds TL exceeded the TL1
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.4 |
gnOduMonCurrXRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.5 |
gnOduMonCurrXRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.6 |
gnOduMonCurrXDayMinRLThe minimum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.7 |
gnOduMonCurrXDayMaxRLThe maximum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.8 |
gnOduMonCurrXDayTLThresh1ExceedThe number of seconds TL exceeded the TL1 threshold
in the last 24 hours.ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.9 |
gnOduMonCurrXDayRLThresh1ExceedThe number of seconds RL exceeded the RL1 threshold
in the last 24 hours.ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.10 |
gnOduMonCurrXDayRLThresh2ExceedThe number of seconds RL exceeded the RL2 threshold
in the last 24 hours.ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.11 |
gnOduMonCurrXMinTLThe minimum transmitted signal level (TL) in the current 15 minute interval.
(in DBM)ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.12 |
gnOduMonCurrXMaxTLThe maximum transmitted signal level (TL) in the current 15 minute interval.
(in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.13 |
gnOduMonCurrXDayMinTLThe minimum Transmitted Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.14 |
gnOduMonCurrXDayMaxTLThe maximum Transmitted Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.15 |
gnOduMonCurrXXpiThe Current XPI level (in [DBM/100]).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.16 |
gnOduMonCurrXMinXpiThe minimum XPI Level (in [DBM/100]).
in the last 15 minute (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.17 |
gnOduMonCurrXMaxXpiThe maximum XPI Level (in [DBM/100]).
in the last 15 minute (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.18 |
gnOduMonCurrXDayMinXpiThe minimum XPI Level (in [DBM/100]).
in the last 24 hours (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.19 |
gnOduMonCurrXDayMaxXpiThe maximum XPI Level (in [DBM/100]).
in the last 24 hours (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.20 |
gnOduMonCurrXXpiThreshExceedThe number of seconds XPI beneath the XPI
threshold in the last 15 minutes (future develope).ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.21 |
gnOduMonCurrXDayXpiThreshExceedThe number of seconds XPI beneath the XPI threshold
in the last 24 hours (future develope).ro Counter .1.3.6.1.4.1.2281.3.1.6.1.1.22 |
gnOduMonCurrXMseThe Current MSE level (in [DBM/100]).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.1.1.23 |
gnOduMonCurrXLastDayIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.3.1.6.1.1.24 |
gnOduMonIntervalXTableThis table defines/keeps the counters of the 96 last intervals of 15 min. SEQUENCE OF GnOduMonIntervalXEntry .1.3.6.1.4.1.2281.3.1.6.2 |
gnOduMonIntervalXEntryThis is an entry in the Interval Table. This table
is indexed by gnOduMonIntervalXId= 3 for drawer1 ODU and
gnOduMonIntervalXId = 4 for drawer2 ODU and by interval idx GnOduMonIntervalXEntry .1.3.6.1.4.1.2281.3.1.6.2.1 |
gnOduMonIntervalXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.2.1.1 |
gnOduMonIntervalXIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.2.1.2 |
gnOduMonIntervalXMinRLThe minimum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.2.1.3 |
gnOduMonIntervalXMaxRLThe maximum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.2.1.4 |
gnOduMonIntervalXTLThresh1ExceedThe number of seconds TL exceeded the TL1
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.2.1.5 |
gnOduMonIntervalXEventEvents
bit 1 = CommDisc.
bit 2 = CommCon
bit 3 = ATPC2Max.
bit 4 = ATPC2Norm.
Included for future development, not currently supported.ro OCTET STRING .1.3.6.1.4.1.2281.3.1.6.2.1.6 |
gnOduMonIntervalXRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.2.1.7 |
gnOduMonIntervalXRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.2.1.8 |
gnOduMonIntervalXMinTLThe minimum TL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.2.1.9 |
gnOduMonIntervalXMaxTLThe maximum TL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.2.1.10 |
gnOduMonIntervalXMinXpiThe minimum XPI level (in [DBM/100]) in a 15 minutes intervalin (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.2.1.11 |
gnOduMonIntervalXMaxXpiThe maximum XPI level (in [DBM/100]) in a 15 minutes interval (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.2.1.12 |
gnOduMonIntervalXXpiThreshExceedThe number of seconds XPI exceeded the XPI
threshold in a 15 minutes interval (future develope).ro Counter .1.3.6.1.4.1.2281.3.1.6.2.1.13 |
gnOduMonIntervalXIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.3.1.6.2.1.14 |
gnOduMonDayXTableThis table defines/keeps the counters of 96 intervals of 15 min. SEQUENCE OF GnOduMonDayXEntry .1.3.6.1.4.1.2281.3.1.6.3 |
gnOduMonDayXEntryThis is an entry in the Days Table. This table
is indexed by gnOduMonDayXId= 3 for drawer1 ODU and
gnOduMonDayXId = 4 for drawer2 ODU and by day idx.
gnOduMonDayIdx = 1 is one day from now,
gnOduMonDayIdx = 2 is two days from now, and so on... GnOduMonDayXEntry .1.3.6.1.4.1.2281.3.1.6.3.1 |
gnOduMonDayXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.3.1.1 |
gnOduMonDayXIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.3.1.2 |
gnOduMonDayXMinRLThe minimum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.3.1.3 |
gnOduMonDayXMaxRLThe maximum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.3.1.4 |
gnOduMonDayXTLThresh1ExceedThe number of seconds TL exceeded the TL1 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.3.1.5 |
gnOduMonDayXRLThresh1ExceedThe number of seconds RL exceeded the RL1 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.3.1.6 |
gnOduMonDayXRLThresh2ExceedThe number of seconds RL exceeded the RL2 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.3.1.7 |
gnOduMonDayXMinTLThe minimum Transmit Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.3.1.8 |
gnOduMonDayXMaxTLThe maximum Transmit Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.3.1.9 |
gnOduMonDayXMinXpiThe minimum XPI Level (in [DBM/100]) in a 24 hour interval (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.3.1.10 |
gnOduMonDayXMaxXpiThe maximum XPI Level (in [DBM/100]) in a 24 hour interval (future develope).
For [DBM] level divide by 100.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.3.1.11 |
gnOduMonDayXXpiThreshExceedThe number of seconds XPI exceeded the XPI threshold
in a 24 hour interval (future develope).ro Counter .1.3.6.1.4.1.2281.3.1.6.3.1.12 |
gnOduMonDayXIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.3.1.6.3.1.13 |
gnOduMonCurrDiversityXTableThis table defines/keeps the counters of the current 15 min interval. SEQUENCE OF GnOduMonCurrDiversityXEntry .1.3.6.1.4.1.2281.3.1.6.4 |
gnOduMonCurrDiversityXEntryThis is an entry in the Current Interval Table. This table
contains two rows, indexed by gnOduMonCurrCombinedXId= 3 for drawer1 ODU and
gnOduMonCurrDiversityXId = 4 for drawer2 ODU. GnOduMonCurrDiversityXEntry .1.3.6.1.4.1.2281.3.1.6.4.1 |
gnOduMonCurrDiversityXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.4.1.1 |
gnOduMonCurrDiversityXMinRLThe minimum received signal level (RL) in the current 15 minute interval.
(in DBM)ro INTEGER .1.3.6.1.4.1.2281.3.1.6.4.1.2 |
gnOduMonCurrDiversityXMaxRLThe maximum received signal level (RL) in the current 15 minute interval.
(in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.4.1.3 |
gnOduMonCurrDiversityXRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.6.4.1.4 |
gnOduMonCurrDiversityXRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.6.4.1.5 |
gnOduMonCurrDiversityXDayMinRLThe minimum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.4.1.6 |
gnOduMonCurrDiversityXDayMaxRLThe maximum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.4.1.7 |
gnOduMonCurrDiversityXDayRLThresh1ExceedThe number of seconds Diversity RL exceeded the RL1 threshold
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.4.1.8 |
gnOduMonCurrDiversityXDayRLThresh2ExceedThe number of seconds Diversity RL exceeded the RL2 threshold
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.4.1.9 |
gnOduMonIntervalDiversityXTableThis table defines/keeps the counters of the 96 last intervals of 15 min. SEQUENCE OF GnOduMonIntervalDiversityXEntry .1.3.6.1.4.1.2281.3.1.6.5 |
gnOduMonIntervalDiversityXEntryThis is an entry in the Interval Table. This table
is indexed by gnOduMonIntervalDiversityXId= 3 for drawer1 ODU and
gnOduMonIntervalDiversityXId = 4 for drawer2 ODU and by interval idx GnOduMonIntervalDiversityXEntry .1.3.6.1.4.1.2281.3.1.6.5.1 |
gnOduMonIntervalDiversityXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.5.1.1 |
gnOduMonIntervalDiversityXIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.5.1.2 |
gnOduMonIntervalDiversityXMinRLThe minimum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.5.1.3 |
gnOduMonIntervalDiversityXMaxRLThe maximum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.5.1.4 |
gnOduMonIntervalDiversityXRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.5.1.5 |
gnOduMonIntervalDiversityXRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.5.1.6 |
gnOduMonDayDiversityXTableThis table defines/keeps the counters of 96 intervals of 15 min. SEQUENCE OF GnOduMonDayDiversityXEntry .1.3.6.1.4.1.2281.3.1.6.6 |
gnOduMonDayDiversityXEntryThis is an entry in the Days Table. This table
is indexed by gnOduMonDayDiversityXId= 3 for drawer1 ODU and
gnOduMonDayDiversityXId = 4 for drawer2 ODU and by day idx.
gnOduMonDayDiversityXIdx = 1 is one day from now,
gnOduMonDayDiversityXIdx = 2 is two days from now, and so on... GnOduMonDayDiversityXEntry .1.3.6.1.4.1.2281.3.1.6.6.1 |
gnOduMonDayDiversityXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.6.1.1 |
gnOduMonDayDiversityXIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.6.1.2 |
gnOduMonDayDiversityXMinRLThe minimum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.6.1.3 |
gnOduMonDayDiversityXMaxRLThe maximum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.6.1.4 |
gnOduMonDayDiversityXRLThresh1ExceedThe number of seconds RL exceeded the RL1 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.6.1.5 |
gnOduMonDayDiversityXRLThresh2ExceedThe number of seconds RL exceeded the RL2 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.6.1.6 |
gnOduMonCurrCombinedXTableThis table defines/keeps the counters of the current 15 min interval. SEQUENCE OF GnOduMonCurrCombinedXEntry .1.3.6.1.4.1.2281.3.1.6.7 |
gnOduMonCurrCombinedXEntryThis is an entry in the Current Interval Table. This table
contains two rows, indexed by gnOduMonCurrCombinedXId= 3 for drawer1 ODU and
gnOduMonCurrCombinedXId = 4 for drawer2 ODU. GnOduMonCurrCombinedXEntry .1.3.6.1.4.1.2281.3.1.6.7.1 |
gnOduMonCurrCombinedXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.7.1.1 |
gnOduMonCurrCombinedXMinRLThe minimum received signal level (RL) in the current 15 minute interval.
(in DBM)ro INTEGER .1.3.6.1.4.1.2281.3.1.6.7.1.2 |
gnOduMonCurrCombinedXMaxRLThe maximum received signal level (RL) in the current 15 minute interval.
(in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.7.1.3 |
gnOduMonCurrCombinedXRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.6.7.1.4 |
gnOduMonCurrCombinedXRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in the last 15 minutes.ro Counter .1.3.6.1.4.1.2281.3.1.6.7.1.5 |
gnOduMonCurrCombinedXDayMinRLThe minimum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.7.1.6 |
gnOduMonCurrCombinedXDayMaxRLThe maximum Receive Level (in DBM).
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.7.1.7 |
gnOduMonCurrCombinedXDayRLThresh1ExceedThe number of seconds Combined RL exceeded the RL1 threshold
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.7.1.8 |
gnOduMonCurrCombinedXDayRLThresh2ExceedThe number of seconds Combined RL exceeded the RL2 threshold
in the last 24 hours.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.7.1.9 |
gnOduMonIntervalCombinedXTableThis table defines/keeps the counters of the 96 last intervals of 15 min. SEQUENCE OF GnOduMonIntervalCombinedXEntry .1.3.6.1.4.1.2281.3.1.6.8 |
gnOduMonIntervalCombinedXEntryThis is an entry in the Interval Table. This table
is indexed by gnOduMonIntervalCombinedXId= 3 for drawer1 ODU and
gnOduMonIntervalCombinedXId = 4 for drawer2 ODU and by interval idx GnOduMonIntervalCombinedXEntry .1.3.6.1.4.1.2281.3.1.6.8.1 |
gnOduMonIntervalCombinedXIdro Enumeration .1.3.6.1.4.1.2281.3.1.6.8.1.1 |
gnOduMonIntervalCombinedXIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.8.1.2 |
gnOduMonIntervalCombinedXMinRLThe minimum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.8.1.3 |
gnOduMonIntervalCombinedXMaxRLThe maximum RL in a 15 minutes interval. (in DBM).ro INTEGER .1.3.6.1.4.1.2281.3.1.6.8.1.4 |
gnOduMonIntervalCombinedXRLThresh1ExceedThe number of seconds RL exceeded the RL1
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.8.1.5 |
gnOduMonIntervalCombinedXRLThresh2ExceedThe number of seconds RL exceeded the RL2
threshold in a 15 minutes interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.8.1.6 |
gnOduMonDayCombinedXTableThis table defines/keeps the counters of 96 intervals of 15 min. SEQUENCE OF GnOduMonDayCombinedXEntry .1.3.6.1.4.1.2281.3.1.6.9 |
gnOduMonDayCombinedXEntryThis is an entry in the Days Table. This table
is indexed by gnOduMonDayDiversityXId= 3 for drawer1 ODU and
gnOduMonDayCombinedXId = 4 for drawer2 ODU and by day idx.
gnOduMonDayCombinedXIdx = 1 is one day from now,
gnOduMonDayCombinedXIdx = 2 is two days from now, and so on... GnOduMonDayCombinedXEntry .1.3.6.1.4.1.2281.3.1.6.9.1 |
gnOduMonDayCombinedXId.ro Enumeration .1.3.6.1.4.1.2281.3.1.6.9.1.1 |
gnOduMonDayCombinedXIdxThe interval number to which this row is related.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.9.1.2 |
gnOduMonDayCombinedXMinRLThe minimum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.9.1.3 |
gnOduMonDayCombinedXMaxRLThe maximum Receive Level (in DBM).
in a 24 hour interval.ro INTEGER .1.3.6.1.4.1.2281.3.1.6.9.1.4 |
gnOduMonDayCombinedXRLThresh1ExceedThe number of seconds RL exceeded the RL1 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.9.1.5 |
gnOduMonDayCombinedXRLThresh2ExceedThe number of seconds RL exceeded the RL2 threshold
in a 24 hour interval.ro Counter .1.3.6.1.4.1.2281.3.1.6.9.1.6 |
gnIDU OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2 |
gnMdm OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.1 |
gnMdmStatTableThis table maintains the status of the Indoor part
of the system. SEQUENCE OF GnMdmStatEntry .1.3.6.1.4.1.2281.3.2.1.2 |
gnMdmStatEntryThis is an entry in the IDU Modem Configuration Table. This table
contains two rows, indexed by ifIndex= 1 for local modem and
ifIndex = 101 for remote modem. GnMdmStatEntry .1.3.6.1.4.1.2281.3.2.1.2.1 |
gnMdmModStatusThis parameters indicates a modem fault.ro Enumeration .1.3.6.1.4.1.2281.3.2.1.2.1.1 |
gnMdmDemodStatusThis parameters indicates a demodem fault - For Ceragon internal use.ro INTEGER .1.3.6.1.4.1.2281.3.2.1.2.1.2 |
gnMdmDefectBlocksThe number of defected blocks that could not be corrected by the
FECro INTEGER .1.3.6.1.4.1.2281.3.2.1.2.1.3 |
gnMdmBytesCorrectedNumber of bytes corrected by the FECro INTEGER .1.3.6.1.4.1.2281.3.2.1.2.1.4 |
gnMdmClearBCclears Defected Blocks, Defected Bytes and Blocks Corrected.rw Enumeration .1.3.6.1.4.1.2281.3.2.1.2.1.5 |
gnMdmStatXTableThis table maintains the status of the Indoor part
of the system. SEQUENCE OF GnMdmStatXEntry .1.3.6.1.4.1.2281.3.2.1.3 |
gnMdmStatXEntryThis is an entry in the IDU Modem Configuration Table. GnMdmStatXEntry .1.3.6.1.4.1.2281.3.2.1.3.1 |
gnMdmStatXIdro Enumeration .1.3.6.1.4.1.2281.3.2.1.3.1.1 |
gnMdmStatXStandardOrgThis parameter specifies which international standard is used.ro Enumeration .1.3.6.1.4.1.2281.3.2.1.3.1.2 |
gnMdmStatXRemoteConnectionIs the connection between the local manager and
the remote manager.ro Enumeration .1.3.6.1.4.1.2281.3.2.1.3.1.3 |
gnMdmStatXModemTypeThis parameter specifies the modem qam.ro INTEGER .1.3.6.1.4.1.2281.3.2.1.3.1.4 |
gnMdmStatXModemWorkTimeThe modem Work Time (hours).ro INTEGER .1.3.6.1.4.1.2281.3.2.1.3.1.5 |
gnMdmStatXModemSerialNumberThis is the modem serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.3.2.1.3.1.6 |
gnMdmStatXModemFWVerThis is the Modem firmware version.ro DisplayString .1.3.6.1.4.1.2281.3.2.1.3.1.7 |
gnMdmStatXModemFWPostVerThis is the Modem post reset firmware version.ro DisplayString .1.3.6.1.4.1.2281.3.2.1.3.1.8 |
gnMdmStatXModemScriptVerThis is the Modem script version.ro DisplayString .1.3.6.1.4.1.2281.3.2.1.3.1.9 |
gnMdmStatXModemScriptPostVerThis is the Modem post reset script version.ro DisplayString .1.3.6.1.4.1.2281.3.2.1.3.1.10 |
gnMdmStatXIfLoopbackTimeOutThis variable indicates the remaining time (in minutes)
till the relevant loopback timer will be expired.
when starting a loopback and the value of gnMdmStatXIfLoopbackTimeOut is x,
the gnMdmStatXIfLoopbackTimeOut will be also x, after one minute it will be x-1, etc.ro INTEGER .1.3.6.1.4.1.2281.3.2.1.3.1.11 |
gnMdmStatXBoardTypeThis parameter defines the type of the modem for NMS use.ro Enumeration .1.3.6.1.4.1.2281.3.2.1.3.1.12 |
gnMdmStatXDefectedBlocksThe number of defected blocks.ro INTEGER .1.3.6.1.4.1.2281.3.2.1.3.1.13 |
gnMdmCfgTable SEQUENCE OF GnMdmCfgEntry .1.3.6.1.4.1.2281.3.2.1.4 |
gnMdmCfgEntry GnMdmCfgEntry .1.3.6.1.4.1.2281.3.2.1.4.1 |
gnMdmCfgIdro Enumeration .1.3.6.1.4.1.2281.3.2.1.4.1.1 |
gnMdmCfgDiversityModerw Enumeration .1.3.6.1.4.1.2281.3.2.1.4.1.2 |
gnMdmCfgXTableThis table defines the configuration of modem. SEQUENCE OF GnMdmCfgXEntry .1.3.6.1.4.1.2281.3.2.1.5 |
gnMdmCfgXEntryThis is an entry in the modem configuration table. GnMdmCfgXEntry .1.3.6.1.4.1.2281.3.2.1.5.1 |
gnMdmCfgXIdThis value indicates which device is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.1 |
gnMdmCfgXLatencyTyperw Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.2 |
gnMdmCfgXLinkId0 for 'old' system that doesn't support the link ID.
the user can enter values from 1 to 65535rw INTEGER .1.3.6.1.4.1.2281.3.2.1.5.1.3 |
gnMdmCfgXRadioSiderw Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.4 |
gnMdmCfgXMrmcConfThe Link data capacityrw Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.5 |
gnMdmCfgXIfLoopbackThis parameter enable the user to activate a loopback.rw Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.6 |
gnMdmCfgXHwResethwReset - Hardware reset for modem board.rw Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.7 |
gnMdmCfgXPrbsTestThis parameter enable the user to activate the PRBS test.rw Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.8 |
gnMdmCfgXClearCountersThis parameter enable the user to clear the PRBS counters.rw Enumeration .1.3.6.1.4.1.2281.3.2.1.5.1.9 |
gnSpi OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.2 |
gnSpiCfgTableThis table defines the configuration of the SPI part
of the system. SEQUENCE OF GnSpiCfgEntry .1.3.6.1.4.1.2281.3.2.2.1 |
gnSpiCfgEntryThis is an entry in the SPI Configuration Table. This table
contains two rows, indexed by ifIndex= 2 for local SPI and
ifIndex = 102 for remote SPI. GnSpiCfgEntry .1.3.6.1.4.1.2281.3.2.2.1.1 |
gnSpiCfgConnectorThe physical connector of the SPI - Used only in old regeneratorsro Enumeration .1.3.6.1.4.1.2281.3.2.2.1.1.1 |
gnMux OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.3 |
gnRstCfgTableThis table defines the configuration of the regenerator part
of the MUX. SEQUENCE OF GnRstCfgEntry .1.3.6.1.4.1.2281.3.2.3.1 |
gnRstCfgEntryThis is an entry in the Regenerator part of the MUX Configuration Table.
This table contains a row for every interface which type is SONET(39).
for example regenerator on local and remote sides will have four entries
1,2 for local
IDU and 101 and 102 for remote IDU. GnRstCfgEntry .1.3.6.1.4.1.2281.3.2.3.1.1 |
gnRstCfgTransmittedJ0This is the J0 string that would be sent. This string must be 15
characters in length.rw DisplayString .1.3.6.1.4.1.2281.3.2.3.1.1.1 |
gnRstCfgExpectedJ0This is the J0 string that is expected to be received. This string must be
15 characters in length.rw DisplayString .1.3.6.1.4.1.2281.3.2.3.1.1.2 |
gnRstCfgTransparencyJ0Send the received J0 string transparently or send the Transmitted J0
configured string.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.3 |
gnRstCfgRSTAISModeIn the case of a J0 mismatch error, send or don't send AIS.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.4 |
gnRstCfgRstEXCThreshIf the bit error rate is higher than this threshold
an EXC alarm would be generated.
EXC is for excessive.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.5 |
gnRstCfgRstSDThreshIf the bit error rate is higher than this threshold
a SD alarm would be generated.
SD is for Signal Degrade.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.6 |
gnRstCfgTransparencyE1Transmit the order wire data received or terminate the E1 data received.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.7 |
gnRstCfgTransparencyF1Transmit the F1/User channel data received or terminate the F1/User channel data received.
set the TransparencyF1 to disable when the User channel used by In-Band management.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.8 |
gnRstCfgTransparencyUnscrambledTransmit the unscrambled national bytes data received or terminate the
unscrambled national bytes data received.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.9 |
gnRstCfgMngByteLocationThis parameter indicates which media specific bytes are in use and which
are transparent.
not currently supportedrw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.10 |
gnRstCfgE1waysideChannelIf this parameter is enabled, an E1 wayside channel will be sent
through the network using the unused bytes in the SDH header.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.11 |
gnRstCfgTransparencyDCCRTransmit on the DCCR channel or terminate the DCCR channel.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.12 |
gnRstCfgTransparencyB1ChanCorrect B1 byte or send transmit it transparently .rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.13 |
gnRstCfgTestActivateThis field allows the NMS to activate the
following tests:
bit 1 = 1 Force AIS
bit 2 = 1 Force RDI.rw OCTET STRING .1.3.6.1.4.1.2281.3.2.3.1.1.14 |
gnRstCfgLoopbackOptionThis parameter enable the user to activate a loopback .rw Enumeration .1.3.6.1.4.1.2281.3.2.3.1.1.15 |
gnRstStatTableThis table defines the status of the regenerator part
of the MUX. SEQUENCE OF GnRstStatEntry .1.3.6.1.4.1.2281.3.2.3.2 |
gnRstStatEntryThis is an entry in the Regenerator part of the MUX
Status Table. This table contains a row for every interface which type is
SONET(39). GnRstStatEntry .1.3.6.1.4.1.2281.3.2.3.2.1 |
gnRstStatReceivedJ0This is the J0 string received.ro DisplayString .1.3.6.1.4.1.2281.3.2.3.2.1.1 |
gnRstStatBERCurCurrent Bit Error Rate.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.2.1.2 |
gnRstStatStatusbit 2 = LOS
bit 3 = LOF
bit 7 = TIM
bit 9 = SD
bit 10 = EXC
bit 11 = UNEXPro OCTET STRING .1.3.6.1.4.1.2281.3.2.3.2.1.3 |
gnRstStatClearLoopTimerThis variable indicates the remaining time (in minutes)
till the relevant loopback timer will be expired.
when starting a loopback and the value of gnGenCfgClearLoopTimeout is x,
the gnRstStatClearLoopTimer will be also x, after one minute it will be x-1, etc.
gnRstStatClearLoopTimer.1 is for the radio aggregate loopbacks,
gnRstStatClearLoopTimer.2 is for the line aggregate loopbacksro INTEGER .1.3.6.1.4.1.2281.3.2.3.2.1.4 |
gnRstMon OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.3.3 |
gnRstMonCurrTableThis table maintains the counters of the regenerator part
of the MUX. SEQUENCE OF GnRstMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.3.1 |
gnRstMonCurrEntryThis is an entry in the Regenerator part of the MUX
Counters Table. This table contains a row for every interface which type
is SONET(39). GnRstMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.3.1.1 |
gnRstMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.1.1.1 |
gnRstMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.1.1.2 |
gnRstMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.1.1.3 |
gnRstMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.1.1.4 |
gnRstMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.1.1.5 |
gnRstMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.1.1.6 |
gnRstMonCurrLastDayOFSThe current number of Out Of Frame Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.1.1.7 |
gnRstMonCurrLastDayIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.3.1.1.8 |
gnRstMonIntervalTableThis table maintains the counters of the regenerator part
of the MUX per interval. SEQUENCE OF GnRstMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.3.2 |
gnRstMonIntervalEntryThis is an entry in the Regenerator part of the MUX
Counters Table. This table contains an interface index for every interface
which type is SONET(39).
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnRstMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.3.2.1 |
gnRstMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.3.2.1.1 |
gnRstMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.2.1.2 |
gnRstMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.2.1.3 |
gnRstMonIntervalIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.3.2.1.4 |
gnRstMonDayTableThis table maintains the counters of the regenerator part
of the MUX per 24 hours interval. SEQUENCE OF GnRstMonDayEntry .1.3.6.1.4.1.2281.3.2.3.3.3 |
gnRstMonDayEntryThis is an entry in the Regenerator part of the MUX
Counters Table. This table contains an interface index for every interface
which type is SONET(39).
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnRstMonDayEntry .1.3.6.1.4.1.2281.3.2.3.3.3.1 |
gnRstMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.3.3.1.1 |
gnRstMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.3.1.2 |
gnRstMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.3.1.3 |
gnRstMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.3.1.4 |
gnRstMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.3.1.5 |
gnRstMonDayOFSThe number of Out Of Frame Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.3.3.1.6 |
gnRstMonDayIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.3.3.1.7 |
gnMstCfgTableThis table maintains the counters of the MST part
of the MUX. SEQUENCE OF GnMstCfgEntry .1.3.6.1.4.1.2281.3.2.3.4 |
gnMstCfgEntryThis is an entry in the MST part of the MUX
Configuration Table. This table contains a row for every interface
which type is SONET(39). GnMstCfgEntry .1.3.6.1.4.1.2281.3.2.3.4.1 |
gnMstCfgEXCThreshIf the bit error rate is higher than this threshold
an EXC alarm would be generated.
EXC is for excessive.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.4.1.1 |
gnMstCfgSDThreshIf the bit error rate is higher than this threshold
a SD alarm would be generated.
SD is for Signal Degrade.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.4.1.2 |
gnMstStatTableThis table defines the status of the MST part
of the MUX. SEQUENCE OF GnMstStatEntry .1.3.6.1.4.1.2281.3.2.3.5 |
gnMstStatEntryThis is an entry in the MST part of the MUX
Status Table. This table contains a row for every interface which type is
SONET(39). GnMstStatEntry .1.3.6.1.4.1.2281.3.2.3.5.1 |
gnMstStatReceivedS1Received Synchronization status byte.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.5.1.1 |
gnMstStatStatusAlarm status. Bit 1 is MSB, bit=1 when alarm active.
bit 5 = RDI
bit 6 = AIS
bit 9 = SD
bit 10 = EXC
bit 16 = PAM (MSP)
bit 17 = SCM (MSP)
bit 18 = INV (MSP)ro OCTET STRING .1.3.6.1.4.1.2281.3.2.3.5.1.2 |
gnMstStatTransmitS1Transmitted Synchronization status byte.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.5.1.3 |
gnMstStatCurrentBerro Enumeration .1.3.6.1.4.1.2281.3.2.3.5.1.4 |
gnMstStatReceivedK1Received K1 byte (Automatic Protection Switch message).ro INTEGER .1.3.6.1.4.1.2281.3.2.3.5.1.5 |
gnMstStatReceivedK2Received K2 byte (Automatic Protection Switch message).ro INTEGER .1.3.6.1.4.1.2281.3.2.3.5.1.6 |
gnMstStatTransmitK1Transmitted K1 byte (Automatic Protection Switch message).ro INTEGER .1.3.6.1.4.1.2281.3.2.3.5.1.7 |
gnMstStatTransmitK2Transmitted K2 byte (Automatic Protection Switch message).ro INTEGER .1.3.6.1.4.1.2281.3.2.3.5.1.8 |
gnMstMon OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.3.6 |
gnMstMonCurrTableThis table maintains the counters of the MST part
of the MUX. SEQUENCE OF GnMstMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.6.1 |
gnMstMonCurrEntryThis is an entry in the MST part of the MUX
Counters Table. This table contains a row for every interface which type
is SONET(39). GnMstMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.6.1.1 |
gnMstMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.1.1.1 |
gnMstMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.1.1.2 |
gnMstMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.1.1.3 |
gnMstMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.1.1.4 |
gnMstMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.1.1.5 |
gnMstMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.1.1.6 |
gnMstMonIntervalTableThis table maintains the counters of the MST part
of the MUX per interval. SEQUENCE OF GnMstMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.6.2 |
gnMstMonIntervalEntryThis is an entry in the MST part of the MUX
Counters Table. This table contains an interface index for every interface
which type is SONET(39).
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnMstMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.6.2.1 |
gnMstMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.6.2.1.1 |
gnMstMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.2.1.2 |
gnMstMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.2.1.3 |
gnMstMonDayTableThis table maintains the counters of the MST part
of the MUX per 24 hours interval. SEQUENCE OF GnMstMonDayEntry .1.3.6.1.4.1.2281.3.2.3.6.3 |
gnMstMonDayEntryThis is an entry in the MST part of the MUX
Counters Table. This table contains an interface index for every interface
which type is SONET(39).
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnMstMonDayEntry .1.3.6.1.4.1.2281.3.2.3.6.3.1 |
gnMstMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.6.3.1.1 |
gnMstMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.3.1.2 |
gnMstMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.3.1.3 |
gnMstMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.3.1.4 |
gnMstMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.3.1.5 |
gnMstFarEndMonCurrTableThis table maintains the counters of the far end MST part of the MUX.
This Table is not supported. SEQUENCE OF GnMstFarEndMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.6.4 |
gnMstFarEndMonCurrEntryThis is an entry in the far end MST part of the MUX
Counters Table. This table contains an interface index for every interface
which type is SONET(39). GnMstFarEndMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.6.4.1 |
gnMstFarEndMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.4.1.1 |
gnMstFarEndMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.4.1.2 |
gnMstFarEndMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.4.1.3 |
gnMstFarEndMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.4.1.4 |
gnMstFarEndMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.4.1.5 |
gnMstFarEndMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.4.1.6 |
gnMstFarEndMonIntervalTableThis table maintains the counters of the far end MST part
of the MUX per interval.
This Table is not supported. SEQUENCE OF GnMstFarEndMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.6.5 |
gnMstFarEndMonIntervalEntryThis is an entry in the far end MST part of the MUX
Counters Table. This table contains an interface index for every interface
which type is SONET(39)
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnMstFarEndMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.6.5.1 |
gnMstFarEndMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.6.5.1.1 |
gnMstFarEndMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.5.1.2 |
gnMstFarEndMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.5.1.3 |
gnMstFarEndMonDayTableThis table maintains the counters of the far end MST part
of the MUX per 24 hours interval.
This Table is not supported. SEQUENCE OF GnMstFarEndMonDayEntry .1.3.6.1.4.1.2281.3.2.3.6.6 |
gnMstFarEndMonDayEntryThis is an entry in the far end MST part of the MUX
Counters Table. This table contains an interface index for every interface
which type is SONET(39).
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnMstFarEndMonDayEntry .1.3.6.1.4.1.2281.3.2.3.6.6.1 |
gnMstFarEndMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.6.6.1.1 |
gnMstFarEndMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.6.1.2 |
gnMstFarEndMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.6.1.3 |
gnMstFarEndMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.6.1.4 |
gnMstFarEndMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.6.6.1.5 |
gnHptCfgTableThis table maintains the counters of the HPT part
of the MUX. SEQUENCE OF GnHptCfgEntry .1.3.6.1.4.1.2281.3.2.3.7 |
gnHptCfgEntryThis is an entry in the HPT part of the MUX
Configuration Table. This table contains an interface index for every
interface
which type is PATH(50, according to RFC1573). GnHptCfgEntry .1.3.6.1.4.1.2281.3.2.3.7.1 |
gnHptCfgTransmittedJ1This is the J1 string that would be sent.rw DisplayString .1.3.6.1.4.1.2281.3.2.3.7.1.1 |
gnHptCfgExpectedJ1This is the J1 string that is expected to be received.rw DisplayString .1.3.6.1.4.1.2281.3.2.3.7.1.2 |
gnHptCfgMismatchJ1In case of a J1 mismatch error, send or don't send AIS.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.7.1.3 |
gnHptCfgTransparencyJ1Send the received J1 string transparently or send the Transmitted J1
configured string.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.7.1.4 |
gnHptCfgEXCThreshIf the bit error rate is higher than this threshold
an EXC alarm would be generated.
EXC is for excessive.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.7.1.5 |
gnHptCfgSDThreshIf the bit error rate is higher than this threshold
a SD alarm would be generated.
SD is for Signal Degrade.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.7.1.6 |
gnHptCfgTug3Structure1This field set the TUG-3 #1 structure: (hexadecimal number)
the lsb 4 bits set VC12=0 or VC3=1 structure to the TUG3 #1. (the K of the KLM index is 1)
for VC12 structure the next 21 bits (for SDH) or 28 bits (for SONET) set each of the VC12
to be blocked (bit is 0) or unblocked (bit is 1).
if it is VC3 only one more bit indicates if it is blocked (0) or unblocked (1).
if a VC12 is set to blocked (this is the default) the system will send TU-AIS in that VC12.
it it is unblocked it will be path-through or mapped to a E1/T1 port (according to the gnAccessCfgLowPathIndex).
the 21 or 28 bits order is as folwed (from lsb to msb direction): first 7 bits for M=1 (from KLM index),
the next 7 bits for M=2, the next for M=3, and the last (only for SONET) for M=4.
Example : SDH, VC12 strcture, blocked VCs: KLM=111,121 (M=1), 112,122 (M=2), 163,173 (M=3), unblocked VCs: all the other.
the value in bits will be: 0011111 1111100 1111100 0000, and in Hexadecimal: 0x7FE7C0. (so enter: 00 7F E7 C0).rw OCTET STRING .1.3.6.1.4.1.2281.3.2.3.7.1.7 |
gnHptCfgTug3Structure2This field set the TUG-3 #2 structure: (hexadecimal number)
the lsb 4 bits set VC12=0 or VC3=1 structure to the TUG-3 #2. (the K of the KLM index is 2)
for VC12 structure the next 21 bits (for SDH) or 28 bits (for SONET) set each of the VC12
to be blocked (bit is 0) or unblocked (bit is 1).
if it is VC3 only one more bit indicates if it is blocked (0) or unblocked (1).
if a VC12 is set to blocked (this is the default) the system will send TU-AIS in that VC12.
it it is unblocked it will be path-through or mapped to a E1/T1 port (according to the gnAccessCfgLowPathIndex).
the 21 or 28 bits order is as folwed (from lsb to msb direction): first 7 bits for M=1 (from KLM index),
the next 7 bits for M=2, the next for M=3, and the last (only for SONET) for M=4.
Example : SDH, VC12 strcture, blocked VCs: KLM=211,221 (M=1), 212,222 (M=2), 263,273 (M=3), unblocked VCs: all the other.
the value in bits will be: 0011111 1111100 1111100 0000, and in Hexadecimal: 0x7FE7C0. (so enter: 00 7F E7 C0).rw OCTET STRING .1.3.6.1.4.1.2281.3.2.3.7.1.8 |
gnHptCfgTug3Structure3This field set the TUG-3 #3 structure: (hexadecimal number)
the lsb 4 bits set VC12=0 or VC3=1 structure to the TUG-3 #3. (the K of the KLM index is 3)
for VC12 structure the next 21 bits (for SDH) or 28 bits (for SONET) set each of the VC12
to be blocked (bit is 0) or unblocked (bit is 1).
if it is VC3 only one more bit indicates if it is blocked (0) or unblocked (1).
if a VC12 is set to blocked (this is the default) the system will send TU-AIS in that VC12.
it it is unblocked it will be path-through or mapped to a E1/T1 port (according to the gnAccessCfgLowPathIndex).
the 21 or 28 bits order is as folwed (from lsb to msb direction): first 7 bits for M=1 (from KLM index),
the next 7 bits for M=2, the next for M=3, and the last (only for SONET) for M=4.
Example : SDH, VC12 strcture, blocked VCs: KLM=311,321 (M=1), 312,322 (M=2), 363,373 (M=3), unblocked VCs: all the other.
the value in bits will be: 0011111 1111100 1111100 0000, and in Hexadecimal: 0x7FE7C0. (so enter: 00 7F E7 C0).rw OCTET STRING .1.3.6.1.4.1.2281.3.2.3.7.1.9 |
gnHptCfgSignalLabelMismatchIn case of a C2 mismatch error, send or don't send AIS.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.7.1.10 |
gnHptCfgTrailPT1This field set the TUG-3 #1 Trails Pass Through (hexadecimal number)
It used by the NMS to indicate that a trail is not 'ended' on this ADM, but it is the
last in the configuration chain.
the lsb 4 bits set VC12=0 or VC3=1 structure to the TUG-3 #1.
for VC12 structure the next 21 bits (for SDH) or 28 bits (for SONET) set each of the VC12
to be blocked (bit is 0) or unblocked (bit is 1).
if it is VC3 only one more bit indicates if it is Pass-Through disabled (0, default) or Pass-Through enabled (1).
if it is VC12, the 21 or 28 bits order is as folwed (from lsb to msb direction): first 7 bits for M=1 (from KLM index),
the next 7 bits for M=2, the next for M=3, and the last (only for SONET) for M=4.rw OCTET STRING .1.3.6.1.4.1.2281.3.2.3.7.1.11 |
gnHptCfgTrailPT2This field set the TUG-3 #2 Trails Pass Through (hexadecimal number).
It used by the NMS to indicate that a trail is not 'ended' on this ADM, but it is the
last in the configuration chain.
the lsb 4 bits set VC12=0 or VC3=1 structure to the TUG-3 #2.
for VC12 structure the next 21 bits (for SDH) or 28 bits (for SONET) set each of the VC12
to be blocked (bit is 0) or unblocked (bit is 1).
if it is VC3 only one more bit indicates if it is Pass-Through disabled (0, default) or Pass-Through enabled (1).
if it is VC12, the 21 or 28 bits order is as folwed (from lsb to msb direction): first 7 bits for M=1 (from KLM index),
the next 7 bits for M=2, the next for M=3, and the last (only for SONET) for M=4.rw OCTET STRING .1.3.6.1.4.1.2281.3.2.3.7.1.12 |
gnHptCfgTrailPT3This field set the TUG-3 #3 Trails Pass Through (hexadecimal number)
It used by the NMS to indicate that a trail is not 'ended' on this ADM, but it is the
last in the configuration chain.
the lsb 4 bits set VC12=0 or VC3=1 structure to the TUG-3 #3.
for VC12 structure the next 21 bits (for SDH) or 28 bits (for SONET) set each of the VC12
to be blocked (bit is 0) or unblocked (bit is 1).
if it is VC3 only one more bit indicates if it is Pass-Through disabled (0, default) or Pass-Through enabled (1).
if it is VC12, the 21 or 28 bits order is as folwed (from lsb to msb direction): first 7 bits for M=1 (from KLM index),
the next 7 bits for M=2, the next for M=3, and the last (only for SONET) for M=4.rw OCTET STRING .1.3.6.1.4.1.2281.3.2.3.7.1.13 |
gnHptStatTableThis table defines the status of the HPT part
of the MUX. SEQUENCE OF GnHptStatEntry .1.3.6.1.4.1.2281.3.2.3.8 |
gnHptStatEntryThis is an entry in the HPT part of the MUX
Status Table. This table contains an interface index for every interface
which type is PATH(50, according to RFC1573). GnHptStatEntry .1.3.6.1.4.1.2281.3.2.3.8.1 |
gnHptStatReceivedJ1This is the J1 string that was received.ro DisplayString .1.3.6.1.4.1.2281.3.2.3.8.1.1 |
gnHptStatStatusAlarm status byte. Bit 1 is MSB, bit=1 when alarm active.
bit 4 = LOP
bit 5 = RDI
bit 6 = AIS
bit 7 = TIM
bit 8 = SLM/PLM
bit 9 = SD
bit 10 = EXC
bit 12 = UNEQ
bit 15 = LOMro OCTET STRING .1.3.6.1.4.1.2281.3.2.3.8.1.2 |
gnHptStatCurrentBerro Enumeration .1.3.6.1.4.1.2281.3.2.3.8.1.3 |
gnHptStatFarEndCurrentBerro Enumeration .1.3.6.1.4.1.2281.3.2.3.8.1.4 |
gnHptStatReceivedSignalLabelThis is the C2 string that was received.ro OCTET STRING .1.3.6.1.4.1.2281.3.2.3.8.1.5 |
gnHptMon OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.3.9 |
gnHptMonCurrTableThis table maintains the counters of the HPT part
of the MUX. SEQUENCE OF GnHptMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.9.1 |
gnHptMonCurrEntryThis is an entry in the HPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is PATH(50, according to RFC1573). GnHptMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.9.1.1 |
gnHptMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.1.1.1 |
gnHptMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.1.1.2 |
gnHptMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.1.1.3 |
gnHptMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.1.1.4 |
gnHptMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.1.1.5 |
gnHptMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.1.1.6 |
gnHptMonIntervalTableThis table maintains the counters of the HPT part
of the MUX per interval. SEQUENCE OF GnHptMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.9.2 |
gnHptMonIntervalEntryThis is an entry in the HPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is PATH(50, according to RFC1573).
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnHptMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.9.2.1 |
gnHptMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.9.2.1.1 |
gnHptMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.2.1.2 |
gnHptMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.2.1.3 |
gnHptMonDayTableThis table maintains the counters of the HPT part
of the MUX per 24 hours interval. SEQUENCE OF GnHptMonDayEntry .1.3.6.1.4.1.2281.3.2.3.9.3 |
gnHptMonDayEntryThis is an entry in the HPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is PATH(50, according to RFC1573).
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnHptMonDayEntry .1.3.6.1.4.1.2281.3.2.3.9.3.1 |
gnHptMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.9.3.1.1 |
gnHptMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.3.1.2 |
gnHptMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.3.1.3 |
gnHptMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.3.1.4 |
gnHptMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.3.1.5 |
gnHptFarEndMonCurrTableThis table maintains the counters of the far end HPT part
of the MUX. SEQUENCE OF GnHptFarEndMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.9.4 |
gnHptFarEndMonCurrEntryThis is an entry in the far end HPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is PATH(50, according to RFC1573). GnHptFarEndMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.9.4.1 |
gnHptFarEndMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.4.1.1 |
gnHptFarEndMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.4.1.2 |
gnHptFarEndMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.4.1.3 |
gnHptFarEndMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.4.1.4 |
gnHptFarEndMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.4.1.5 |
gnHptFarEndMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.4.1.6 |
gnHptFarEndMonIntervalTableThis table maintains the counters of the far end HPT part
of the MUX per interval. SEQUENCE OF GnHptFarEndMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.9.5 |
gnHptFarEndMonIntervalEntryThis is an entry in the far end HPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is PATH(50, according to RFC1573).
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnHptFarEndMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.9.5.1 |
gnHptFarEndMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.9.5.1.1 |
gnHptFarEndMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.5.1.2 |
gnHptFarEndMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.5.1.3 |
gnHptFarEndMonDayTableThis table maintains the counters of the far end HPT part
of the MUX per 24 hours interval. SEQUENCE OF GnHptFarEndMonDayEntry .1.3.6.1.4.1.2281.3.2.3.9.6 |
gnHptFarEndMonDayEntryThis is an entry in the far end HPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is PATH(50, according to RFC1573).
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnHptFarEndMonDayEntry .1.3.6.1.4.1.2281.3.2.3.9.6.1 |
gnHptFarEndMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.9.6.1.1 |
gnHptFarEndMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.6.1.2 |
gnHptFarEndMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.6.1.3 |
gnHptFarEndMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.6.1.4 |
gnHptFarEndMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.9.6.1.5 |
gnLptCfgTableThis table maintains the counters of the LPT part
of the MUX. SEQUENCE OF GnLptCfgEntry .1.3.6.1.4.1.2281.3.2.3.10 |
gnLptCfgEntryThis is an entry in the LPT part of the MUX
Configuration Table. This table contains an interface index for every
interface which type is VT(51, according to RFC1573). GnLptCfgEntry .1.3.6.1.4.1.2281.3.2.3.10.1 |
gnLptCfgEXCThreshIf the bit error rate is higher than this threshold
an alarm would be generated.
EXC is for excessive.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.10.1.1 |
gnLptCfgSDThreshIf the bit error rate is higher than this threshold
an alarm would be generated.
SD is for Signal Degrade.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.10.1.2 |
gnLptStatTableThis table defines the status of the LPT part
of the MUX. SEQUENCE OF GnLptStatEntry .1.3.6.1.4.1.2281.3.2.3.11 |
gnLptStatEntryThis is an entry in the LPT part of the MUX
Status Table. This table contains an interface index for every interface
which type is VT(51, according to RFC1573). GnLptStatEntry .1.3.6.1.4.1.2281.3.2.3.11.1 |
gnLptStatReceivedJ2This is the J2 string that was received.ro DisplayString .1.3.6.1.4.1.2281.3.2.3.11.1.1 |
gnLptStatStatusAlarm status byte. Bit 1 is MSB, bit=1 when alarm active.
bit 4 = LOP
bit 5 = RDI
bit 6 = AIS
bit 7 = TIM
bit 8 = SLM/PLM
bit 9 = SD
bit 10 = EXC
bit 12 = UNEQro OCTET STRING .1.3.6.1.4.1.2281.3.2.3.11.1.2 |
gnLptStatProtectionModero Enumeration .1.3.6.1.4.1.2281.3.2.3.11.1.3 |
gnLptStatCurrentBerro Enumeration .1.3.6.1.4.1.2281.3.2.3.11.1.4 |
gnLptStatFarEndCurrentBerro Enumeration .1.3.6.1.4.1.2281.3.2.3.11.1.5 |
gnLptStatReceivedSignalLabelThese are bits 1..3 of the V5 string that was received
(bit 0 is the lsb).ro OCTET STRING .1.3.6.1.4.1.2281.3.2.3.11.1.6 |
gnLptStatKLMro INTEGER .1.3.6.1.4.1.2281.3.2.3.11.1.7 |
gnLptMon OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.3.12 |
gnLptMonCurrTableThis table maintains the counters of the LPT part
of the MUX. SEQUENCE OF GnLptMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.12.1 |
gnLptMonCurrEntryThis is an entry in the LPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is VT(51, according to RFC1573). GnLptMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.12.1.1 |
gnLptMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.1.1.1 |
gnLptMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.1.1.2 |
gnLptMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.1.1.3 |
gnLptMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.1.1.4 |
gnLptMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.1.1.5 |
gnLptMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.1.1.6 |
gnLptMonIntervalTableThis table maintains the counters of the LPT part
of the MUX per interval. SEQUENCE OF GnLptMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.12.2 |
gnLptMonIntervalEntryThis is an entry in the LPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is VT(51, according to RFC1573).
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnLptMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.12.2.1 |
gnLptMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.12.2.1.1 |
gnLptMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.2.1.2 |
gnLptMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.2.1.3 |
gnLptMonDayTableThis table maintains the counters of the LPT part
of the MUX per 24 hours interval. SEQUENCE OF GnLptMonDayEntry .1.3.6.1.4.1.2281.3.2.3.12.3 |
gnLptMonDayEntryThis is an entry in the LPT part of the MUX
Counters Table. This table contains four groups of rows,
indexed by ifIndex= 1,2 for local IDU and
ifIndex = 101 and 102 for remote IDU.
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnLptMonDayEntry .1.3.6.1.4.1.2281.3.2.3.12.3.1 |
gnLptMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.12.3.1.1 |
gnLptMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.3.1.2 |
gnLptMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.3.1.3 |
gnLptMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.3.1.4 |
gnLptMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.3.1.5 |
gnLptFarEndMonCurrTableThis table maintains the counters of the far end LPT part
of the MUX. SEQUENCE OF GnLptFarEndMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.12.4 |
gnLptFarEndMonCurrEntryThis is an entry in the far end LPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is VT(51, according to RFC1573). GnLptFarEndMonCurrEntry .1.3.6.1.4.1.2281.3.2.3.12.4.1 |
gnLptFarEndMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.4.1.1 |
gnLptFarEndMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.4.1.2 |
gnLptFarEndMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.4.1.3 |
gnLptFarEndMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.4.1.4 |
gnLptFarEndMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.4.1.5 |
gnLptFarEndMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.4.1.6 |
gnLptFarEndMonIntervalTableThis table maintains the counters of the far end LPT part
of the MUX per interval. SEQUENCE OF GnLptFarEndMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.12.5 |
gnLptFarEndMonIntervalEntryThis is an entry in the far end LPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is VT(51, according to RFC1573).
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnLptFarEndMonIntervalEntry .1.3.6.1.4.1.2281.3.2.3.12.5.1 |
gnLptFarEndMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.12.5.1.1 |
gnLptFarEndMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.5.1.2 |
gnLptFarEndMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.5.1.3 |
gnLptFarEndMonDayTableThis table maintains the counters of the far end LPT part
of the MUX per 24 hours interval. SEQUENCE OF GnLptFarEndMonDayEntry .1.3.6.1.4.1.2281.3.2.3.12.6 |
gnLptFarEndMonDayEntryThis is an entry in the far end LPT part of the MUX
Counters Table. This table contains an interface index for every interface
which type is VT(51, according to RFC1573).
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnLptFarEndMonDayEntry .1.3.6.1.4.1.2281.3.2.3.12.6.1 |
gnLptFarEndMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.12.6.1.1 |
gnLptFarEndMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.6.1.2 |
gnLptFarEndMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.6.1.3 |
gnLptFarEndMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.6.1.4 |
gnLptFarEndMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.3.2.3.12.6.1.5 |
gnMuxCfgXTableThis table defines the configuration of the mux board. SEQUENCE OF GnMuxCfgXEntry .1.3.6.1.4.1.2281.3.2.3.13 |
gnMuxCfgXEntryThis is an entry in the mux configuration table. GnMuxCfgXEntry .1.3.6.1.4.1.2281.3.2.3.13.1 |
gnMuxCfgXIdThis value indicates which device is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.13.1.1 |
gnMuxCfgXWsAdminEnable Disable drawer wayside channelrw Enumeration .1.3.6.1.4.1.2281.3.2.3.13.1.2 |
gnMuxCfgXWsLoopbackThis parameter controls the WAYSIDE channel loopback diagnostic operations.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.13.1.3 |
gnMuxCfgXHwResethwReset - Hardware reset for mux board.rw Enumeration .1.3.6.1.4.1.2281.3.2.3.13.1.4 |
gnMUXCfgXTempLicenseEnableSet temporary license enable or disablerw Enumeration .1.3.6.1.4.1.2281.3.2.3.13.1.5 |
gnMUXCfgXTempLicenseTimerThis value indicates the temporary license timerro INTEGER .1.3.6.1.4.1.2281.3.2.3.13.1.6 |
gnMuxStatXTableThis table defines the status of the mux board. SEQUENCE OF GnMuxStatXEntry .1.3.6.1.4.1.2281.3.2.3.14 |
gnMuxStatXEntryThis is an entry in the mux configuration table. GnMuxStatXEntry .1.3.6.1.4.1.2281.3.2.3.14.1 |
gnMuxStatXIdThis value indicates which device is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.14.1.1 |
gnMuxStatXMuxSerialNumberThis is the MUX serial number - up to 20 charactersro DisplayString .1.3.6.1.4.1.2281.3.2.3.14.1.2 |
gnMuxStatXIfLedsThe status of the Interface LEDs. For the management station use.
Each two bits represents one led as follows: 00 - Gray, 01 - Green, 10 - Orange, 11 - Red.
The led order: Led1 is msb 2 bits , after it led2, till led 16 - 2 lsb bits.ro OCTET STRING .1.3.6.1.4.1.2281.3.2.3.14.1.3 |
gnMuxStatXNumOfIfOnClass1This value indicates the actual number of interfaces on class 1.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.14.1.4 |
gnMuxStatXNumOfIfOnClass2This value indicates the actual number of interfaces on class 2.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.14.1.5 |
gnMuxStatXNumOfIfOnClass3This value indicates the actual number of interfaces on class 3.ro INTEGER .1.3.6.1.4.1.2281.3.2.3.14.1.6 |
gnMuxStatXAesAdminThis parameter defines encryption admin mode.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.14.1.7 |
gnMuxStatXMuxFWVerThis is the Mux firmware version.ro DisplayString .1.3.6.1.4.1.2281.3.2.3.14.1.8 |
gnMuxStatXMuxFWPostVerThis is the Mux post reset firmware version.ro DisplayString .1.3.6.1.4.1.2281.3.2.3.14.1.9 |
gnMuxStatXBoardConnectorThis parameter defines the connector of the mux board, for NMS use.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.14.1.10 |
gnMuxStatXBoardTypeThis parameter defines the type of the mux.ro Enumeration .1.3.6.1.4.1.2281.3.2.3.14.1.11 |
gnAux OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.4 |
gnAuxGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.4.1 |
gnAuxGeneralTableThis table defines the commands of the Auxiliary channel. SEQUENCE OF GnAuxGeneralEntry .1.3.6.1.4.1.2281.3.2.4.1.1 |
gnAuxGeneralEntryThis is an entry in the Auxiliary channel command Table. GnAuxGeneralEntry .1.3.6.1.4.1.2281.3.2.4.1.1.1 |
gnAuxGeneralIdro Enumeration .1.3.6.1.4.1.2281.3.2.4.1.1.1.1 |
gnAuxGeneralSyncIdcDataBaseThis parameter synchronize between hardware and data base of auxiliary channel.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.1.1.1.2 |
gnWsc OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.4.2 |
gnWscCfgTableThis table defines the configuration of the Wayside channel. SEQUENCE OF GnWscCfgEntry .1.3.6.1.4.1.2281.3.2.4.2.1 |
gnWscCfgEntryThis is an entry in the Wayside channel part of the AUX Configuration Table. GnWscCfgEntry .1.3.6.1.4.1.2281.3.2.4.2.1.1 |
gnWscCfgIdro Enumeration .1.3.6.1.4.1.2281.3.2.4.2.1.1.1 |
gnWscCfgChNumberWayside channel number.ro Enumeration .1.3.6.1.4.1.2281.3.2.4.2.1.1.2 |
gnWscCfgRoutingWayside channel routing.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.2.1.1.3 |
gnWscCfgEnableWayside channel enable\disable.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.2.1.1.4 |
gnWscCfgBitRateWayside channel bit rate.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.2.1.1.5 |
gnWscCfgTypeWayside channel bit rate.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.2.1.1.6 |
gnWscStatTableThis table defines the status of the Wayside channel. SEQUENCE OF GnWscStatEntry .1.3.6.1.4.1.2281.3.2.4.2.2 |
gnWscStatEntryThis is an entry in the Wayside channel part of the AUX Status Table. GnWscStatEntry .1.3.6.1.4.1.2281.3.2.4.2.2.1 |
gnWscStatIdro Enumeration .1.3.6.1.4.1.2281.3.2.4.2.2.1.1 |
gnWscStatChNumberWayside channel number.ro Enumeration .1.3.6.1.4.1.2281.3.2.4.2.2.1.2 |
gnWscStatBitRateSupportIndication for Wayside channel bit rate support.ro Enumeration .1.3.6.1.4.1.2281.3.2.4.2.2.1.3 |
gnEow OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.4.3 |
gnEowCfgTableThis table defines the configuration of the EOW. SEQUENCE OF GnEowCfgEntry .1.3.6.1.4.1.2281.3.2.4.3.1 |
gnEowCfgEntryThis is an entry in the EOW configuration Table. GnEowCfgEntry .1.3.6.1.4.1.2281.3.2.4.3.1.1 |
gnEowCfgIdro Enumeration .1.3.6.1.4.1.2281.3.2.4.3.1.1.1 |
gnEowCfgEowLeftEnableEOW enable\disable.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.3.1.1.2 |
gnEowCfgEowRightEnableEOW enable\disable.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.3.1.1.3 |
gnEowCfgEowCascadeEnableEOW cascade enable\disable.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.3.1.1.4 |
gnEowStatTableThis table defines the status of the EOW. SEQUENCE OF GnEowStatEntry .1.3.6.1.4.1.2281.3.2.4.3.2 |
gnEowStatEntryThis is an entry in the EOW status Table. GnEowStatEntry .1.3.6.1.4.1.2281.3.2.4.3.2.1 |
gnEowStatIdro Enumeration .1.3.6.1.4.1.2281.3.2.4.3.2.1.1 |
gnEowStatEowLeftSupportIndication for EOW support.ro Enumeration .1.3.6.1.4.1.2281.3.2.4.3.2.1.2 |
gnEowStatEowRightSupportIndication for EOW support.ro Enumeration .1.3.6.1.4.1.2281.3.2.4.3.2.1.3 |
gnUc OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.2.4.4 |
gnUcCfgTableThis table defines the configuration of the User channel. SEQUENCE OF GnUcCfgEntry .1.3.6.1.4.1.2281.3.2.4.4.1 |
gnUcCfgEntryThis is an entry in the User channel part of the AUX Configuration Table. GnUcCfgEntry .1.3.6.1.4.1.2281.3.2.4.4.1.1 |
gnUcCfgIdro Enumeration .1.3.6.1.4.1.2281.3.2.4.4.1.1.1 |
gnUcCfgChNumberUser channel number.ro Enumeration .1.3.6.1.4.1.2281.3.2.4.4.1.1.2 |
gnUcCfgRoutingUser channel routing.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.4.1.1.3 |
gnUcCfgEnableUser channel enable\disable.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.4.1.1.4 |
gnUcCfgTypeUser channel protocol type.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.4.1.1.5 |
gnUcCfgLoopbackUser channel loopback activation.rw Enumeration .1.3.6.1.4.1.2281.3.2.4.4.1.1.6 |
gnUcStatTableThis table defines the status of the user channel. SEQUENCE OF GnUcStatEntry .1.3.6.1.4.1.2281.3.2.4.4.2 |
gnUcStatEntryThis is an entry in the user channel status Table. GnUcStatEntry .1.3.6.1.4.1.2281.3.2.4.4.2.1 |
gnUcStatIdro Enumeration .1.3.6.1.4.1.2281.3.2.4.4.2.1.1 |
gnUcStatLeftMaxRouteChannelIndication for NMS on the number of
channels the right radio can passthrough.ro INTEGER .1.3.6.1.4.1.2281.3.2.4.4.2.1.2 |
gnUcStatRightMaxRouteChannelIndication for NMS on the number of
channels the right radio can passthrough.ro INTEGER .1.3.6.1.4.1.2281.3.2.4.4.2.1.3 |
gnProtect OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.3 |
gnProtectCfgTableThis table contains protection switch configuration
per device; local and remote. SEQUENCE OF GnProtectCfgEntry .1.3.6.1.4.1.2281.3.3.1 |
gnProtectCfgEntry GnProtectCfgEntry .1.3.6.1.4.1.2281.3.3.1.1 |
gnProtectCfgIdThis value indicates which device is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.3.3.1.1.1 |
gnProtectCfgSwitchRequestProtection user switch request.rw Enumeration .1.3.6.1.4.1.2281.3.3.1.1.2 |
gnProtectCfgBERSwitchEnable or disable automatic switch as a result of BER condition.rw Enumeration .1.3.6.1.4.1.2281.3.3.1.1.3 |
gnProtectCfgExtInSwitchEnable or disable automatic switch as a result of alarm
on External Input No. 8.rw Enumeration .1.3.6.1.4.1.2281.3.3.1.1.4 |
gnProtectCfgOptionbit 8 (lsb) = dual fiber input.
bit 7 = protection disable
bit 4 = 0 (default) for External protection ; 1 for Internal protection (between the drawers)
bit 3 = 0 (default) for Full protection ; 1 for Radio protection.rw OCTET STRING .1.3.6.1.4.1.2281.3.3.1.1.5 |
gnProtectCfgUserCommandCopy All the configuration that should be equal in master and slave.
The copy is made from the current unit to it's mate/Left drawer to right drawer or right drawer to left drawer.rw Enumeration .1.3.6.1.4.1.2281.3.3.1.1.6 |
gnProtectCfgType.rw Enumeration .1.3.6.1.4.1.2281.3.3.1.1.7 |
gnProtectCfgProtectionLockout.rw Enumeration .1.3.6.1.4.1.2281.3.3.1.1.8 |
gnProtectCfgSdBERSwitchEnable or disable automatic switch as a result of signal degrade BER condition.rw Enumeration .1.3.6.1.4.1.2281.3.3.1.1.9 |
gnProtectUnitModeThis parameter indicates the unit mode: Master of Slave.ro Enumeration .1.3.6.1.4.1.2281.3.3.2 |
gnHitLessCfgTableThis table contains hitless configuration
per device; local and remote. SEQUENCE OF GnHitLessCfgEntry .1.3.6.1.4.1.2281.3.3.3 |
gnHitLessCfgEntry GnHitLessCfgEntry .1.3.6.1.4.1.2281.3.3.3.1 |
gnHitLessCfgIdThis value indicates which device is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.3.3.3.1.1 |
gnHitLessCfgSwitchEnableEnable or disable the Hitless feature.rw Enumeration .1.3.6.1.4.1.2281.3.3.3.1.2 |
gnHitLessCfgDiversityTypeIs the hitless feature working in space diversity mode
or in frequency diversity mode.rw Enumeration .1.3.6.1.4.1.2281.3.3.3.1.3 |
gnHitLessCfgSwitchingModerw Enumeration .1.3.6.1.4.1.2281.3.3.3.1.4 |
gnHitLessCfgRevertTimeThis parameter indicates the revert time in seconds.
Possible values: 0..15.rw INTEGER .1.3.6.1.4.1.2281.3.3.3.1.5 |
gnHitLessCfgManualSwitchForce manually switch between the hitless modems.rw Enumeration .1.3.6.1.4.1.2281.3.3.3.1.6 |
gnHitLessCfgEventCounterCommandClears the gnHitLessStatEventCounter.rw Enumeration .1.3.6.1.4.1.2281.3.3.3.1.7 |
gnHitLessCfgSwitchLock.rw Enumeration .1.3.6.1.4.1.2281.3.3.3.1.8 |
gnHitLessStatTableThis table contains hitless status
per device; local and remote. SEQUENCE OF GnHitLessStatEntry .1.3.6.1.4.1.2281.3.3.4 |
gnHitLessStatEntry GnHitLessStatEntry .1.3.6.1.4.1.2281.3.3.4.1 |
gnHitLessStatIdThis value indicates which device is involved
in the specific row.ro Enumeration .1.3.6.1.4.1.2281.3.3.4.1.1 |
gnHitLessStatReceiverStatusThis parameter indicates which Modem is active:
the Local or the mate.ro Enumeration .1.3.6.1.4.1.2281.3.3.4.1.2 |
gnHitLessStatModeStatusThis parameter indicates if the Hitless system
is working properly.ro Enumeration .1.3.6.1.4.1.2281.3.3.4.1.3 |
gnHitLessStatEventCounterThis counter counts the number of hitless switch events.ro INTEGER .1.3.6.1.4.1.2281.3.3.4.1.4 |
gnHitLessStatAlarmStatusbit 1 represent the MSB
bits 1-7 are not in use
bit 8 : Switch lock to right.
bit 9 : Switch lock to left.
bit 10: Protection config mismatch.
bit 11: Diversity config mismatch.
bit 12: Unused radio LOF.
bit 13: Hitless Functionality Failure.
bit 14: Hitless Cable Disconnect.
bit 15: Hitless Mate LOF.
bit 16: Hitless Primary Radio LOF.ro OCTET STRING .1.3.6.1.4.1.2281.3.3.4.1.5 |
gnTribStmProtectCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.3.5 |
gnTribStmProtectType.rw Enumeration .1.3.6.1.4.1.2281.3.3.5.1 |
gnTribStmMspConnect.rw Enumeration .1.3.6.1.4.1.2281.3.3.5.2 |
gnTribStmMspType.rw Enumeration .1.3.6.1.4.1.2281.3.3.5.3 |
gnTribStmMspRevertiveMode.rw Enumeration .1.3.6.1.4.1.2281.3.3.5.4 |
gnTribStmMspProtectRole.rw Enumeration .1.3.6.1.4.1.2281.3.3.5.5 |
gnTribStmMspWaitToRestoreTimeThis is the wait-to-restore time in minutes.
Possible values: 5..12.rw INTEGER .1.3.6.1.4.1.2281.3.3.5.6 |
gnTribStmMspUserCommand.rw Enumeration .1.3.6.1.4.1.2281.3.3.5.7 |
gnTribStmProtectStat OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.3.6 |
gnTribStmProtectCurrentState.ro Enumeration .1.3.6.1.4.1.2281.3.3.6.1 |
gnTribStmProtectCableStatus.ro Enumeration .1.3.6.1.4.1.2281.3.3.6.2 |
gnProtectXTable SEQUENCE OF GnProtectXEntry .1.3.6.1.4.1.2281.3.3.7 |
gnProtectXEntry GnProtectXEntry .1.3.6.1.4.1.2281.3.3.7.1 |
gnProtectXIdro Enumeration .1.3.6.1.4.1.2281.3.3.7.1.1 |
gnProtectXProtectUnitModeThis parameter indicates the unit mode: Master of Slave.ro Enumeration .1.3.6.1.4.1.2281.3.3.7.1.2 |
gnLinkGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.3.8 |
topologiesOptionsTableThis table indicates the Topologies options. SEQUENCE OF TopologiesOptionsEntry .1.3.6.1.4.1.2281.3.3.8.1 |
topologiesOptionsEntryEntry containing the Topologies options. TopologiesOptionsEntry .1.3.6.1.4.1.2281.3.3.8.1.1 |
protectionTableThis table indicates the link grouping protection. SEQUENCE OF ProtectionEntry .1.3.6.1.4.1.2281.3.3.8.3 |
protectionEntryEntry containing the link grouping protection. ProtectionEntry .1.3.6.1.4.1.2281.3.3.8.3.1 |
protectionGroupIdThis value indicates the group id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.3.1.1 |
protectionGroupsProtectionAdminThis value indicates the groups protection admin.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.3.1.2 |
protectionNplus1ProtectionMethodThis value indicates the N+1 protection method.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.3.1.3 |
protectionProtectingCarrierIdThis value indicates the carrier id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.3.1.4 |
standardProtectionTableThis table indicates the link grouping standard protection. SEQUENCE OF StandardProtectionEntry .1.3.6.1.4.1.2281.3.3.8.4 |
standardProtectionEntryEntry containing the link grouping standard protection. StandardProtectionEntry .1.3.6.1.4.1.2281.3.3.8.4.1 |
standardProtectionGroupIdThis value indicates the group id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.4.1.1 |
standardProtectionSwitchOnEarlyWarningThis value indicates switch on early warning.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.4.1.2 |
standardProtectionHighPrioProtectionThThis value indicates the high priority protection.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.4.1.3 |
standardProtectionRevertiveLinkThis value indicates the revertive link.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.4.1.4 |
standardProtectionRevertiveSwitchTimeOutThis value indicates the revertive switch time out.rw INTEGER .1.3.6.1.4.1.2281.3.3.8.4.1.5 |
membersTableThis table indicates the link groups members. SEQUENCE OF MembersEntry .1.3.6.1.4.1.2281.3.3.8.5 |
membersEntryEntry containing the link groups members. MembersEntry .1.3.6.1.4.1.2281.3.3.8.5.1 |
membersGroupIdThis value indicates the group id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.5.1.1 |
membersCarrierIdThis value indicates the carrier id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.5.1.2 |
membersProtectionPriorityLevelThis value indicates the protection priority level.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.5.1.3 |
nplus1ProtectingTableThis table indicates the link group N+1 protecting. SEQUENCE OF Nplus1ProtectingEntry .1.3.6.1.4.1.2281.3.3.8.6 |
nplus1ProtectingEntryEntry containing the link group N+1 protecting. Nplus1ProtectingEntry .1.3.6.1.4.1.2281.3.3.8.6.1 |
nplus1ProtectingGroupIdThis value indicates the group id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.6.1.1 |
nplus1ProtectingXCProtectionFramingThis value indicates the XC protecting framing.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.6.1.2 |
nplus1ProtectingProtectedLinkTxThis value indicates the last known carrier num. 0 means no carrier.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.6.1.3 |
nplus1ProtectingProtectedLinkRxThis value indicates the last known carrier num. 0 means no carrier.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.6.1.4 |
nplus1ProtectingRequestedLinkTxThis value indicates the last known carrier num. 0 means no carrier.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.6.1.5 |
nplus1ProtectingRequestedLinkRxThis value indicates the last known carrier num. 0 means no carrier.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.6.1.6 |
nplus1ProtectingSwitchToProtectingCommandThis value indicates the switch to protecting command.
The force switch command is Bi-directional.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.6.1.7 |
carrierProtectionTableThis table indicates the carrier protection. SEQUENCE OF CarrierProtectionEntry .1.3.6.1.4.1.2281.3.3.8.7 |
carrierProtectionEntryEntry containing the carrier protection. CarrierProtectionEntry .1.3.6.1.4.1.2281.3.3.8.7.1 |
carrierProtectionXCIdThis value indicates the XC id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.7.1.1 |
carrierProtectionCarrierIdThis value indicates the carrier id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.7.1.2 |
carrierProtectionLinkGroupNumThis value indicates the link group number.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.7.1.3 |
carrierProtectionServedByRemoteXCThis value indicates whether served by remote XC.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.7.1.4 |
carrierProtectionRadioStatusThis value indicates the radio status.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.7.1.5 |
carrierProtectionLineFramingThis value indicates the line framing.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.7.1.6 |
carrierProtectionLoopbackThis value indicates the loopback.rw Enumeration .1.3.6.1.4.1.2281.3.3.8.7.1.7 |
carrierProtectionLoopbackTimerThis variable indicates the remaining time (in minutes) till the loopback timer will be expired.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.7.1.8 |
nplus1StandardPMCurrTableThis table indicates the standard PM current. SEQUENCE OF Nplus1StandardPMCurrEntry .1.3.6.1.4.1.2281.3.3.8.8 |
nplus1StandardPMCurrEntryEntry containing the standard PM current. Nplus1StandardPMCurrEntry .1.3.6.1.4.1.2281.3.3.8.8.1 |
nplus1StandardPMCurrCarrierIdThis value indicates the carrier id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.8.1.1 |
nplus1StandardPMCurrTimeElapsedThis value indicates the time that elapsed.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.8.1.2 |
nplus1StandardPMCurrValidIntervalsThis value indicates the valid intervals.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.8.1.3 |
nplus1StandardPMCurrLastDayIDFThis value indicates the carrier id.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.8.1.4 |
nplus1StandardPMCurrLastDayGroupNumThis value indicates the group's number.ro INTEGER (-1..4) .1.3.6.1.4.1.2281.3.3.8.8.1.5 |
nplus1StandardPMCurrPSACThis value indicates the PSAC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.6 |
nplus1StandardPMCurrFSRCThis value indicates the FSRC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.7 |
nplus1StandardPMCurrPSADThis value indicates the PSAD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.8 |
nplus1StandardPMCurrFSRDThis value indicates the FSRD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.9 |
nplus1StandardPMCurrLastDayPSACThis value indicates the last Day PSAC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.10 |
nplus1StandardPMCurrLastDayFSRCThis value indicates the last Day FSRC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.11 |
nplus1StandardPMCurrLastDayPSADThis value indicates the last Day PSAD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.12 |
nplus1StandardPMCurrLastDayFSRDThis value indicates the last Day FSRD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.8.1.13 |
nplus1StandardPMIntervalTableThis table indicates the standard PM interval. SEQUENCE OF Nplus1StandardPMIntervalEntry .1.3.6.1.4.1.2281.3.3.8.9 |
nplus1StandardPMIntervalEntryEntry containing the standard PM interval. Nplus1StandardPMIntervalEntry .1.3.6.1.4.1.2281.3.3.8.9.1 |
nplus1StandardPMIntervalCarrierIdThis value indicates the carrier id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.9.1.1 |
nplus1StandardPMIntervalIdxThis value indicates the index.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.9.1.2 |
nplus1StandardPMIntervalIDFThis value is an invalid data flag.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.9.1.3 |
nplus1StandardPMIntervalGroupNumThis value indicates the group's number.ro INTEGER (-1..4) .1.3.6.1.4.1.2281.3.3.8.9.1.4 |
nplus1StandardPMIntervalPSACThis value indicates the PSAC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.9.1.5 |
nplus1StandardPMIntervalFSRCThis value indicates the FSRC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.9.1.6 |
nplus1StandardPMIntervalPSADThis value indicates the PSAD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.9.1.7 |
nplus1StandardPMIntervalFSRDThis value indicates the FSRD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.9.1.8 |
nplus1StandardPMDayTableThis table indicates the standard PM day table. SEQUENCE OF Nplus1StandardPMDayEntry .1.3.6.1.4.1.2281.3.3.8.10 |
nplus1StandardPMDayEntryEntry containing the standard PM day table. Nplus1StandardPMDayEntry .1.3.6.1.4.1.2281.3.3.8.10.1 |
nplus1StandardPMDayCarrierIdThis value indicates the carrier id.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.10.1.1 |
nplus1StandardPMDayIdxThis value indicates the index.ro INTEGER .1.3.6.1.4.1.2281.3.3.8.10.1.2 |
nplus1StandardPMDayIDFThis value is an invalid data flag.ro Enumeration .1.3.6.1.4.1.2281.3.3.8.10.1.3 |
nplus1StandardPMDayGroupNumThis value indicates the group's number.ro INTEGER (-1..4) .1.3.6.1.4.1.2281.3.3.8.10.1.4 |
nplus1StandardPMDayPSACThis value indicates the PSAC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.10.1.5 |
nplus1StandardPMDayFSRCThis value indicates the FSRC value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.10.1.6 |
nplus1StandardPMDayPSADThis value indicates the PSAD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.10.1.7 |
nplus1StandardPMDayFSRDThis value indicates the FSRD value.ro Gauge .1.3.6.1.4.1.2281.3.3.8.10.1.8 |
gnSSM OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.4 |
gnSSMCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.4.1 |
gnSSMCfgSSMModerw Enumeration .1.3.6.1.4.1.2281.3.4.1.1 |
gnSSMCfgPrimaryClockSourceThe primary clock source, configurable for ACCESS radios only.rw Enumeration .1.3.6.1.4.1.2281.3.4.1.2 |
gnSSMCfgPrimaryClockQualityThis parameter indicates the primary clock quality.
Possible values for SDH:
PRC(1), SSUT(2), SSUL(3), SEC(4), STU(5).
Possible values for Sonet:
PRS(1), STU(2), ST2(3), ST3(4), SMC(5), ST4(6).rw INTEGER .1.3.6.1.4.1.2281.3.4.1.3 |
gnSSMCfgSecondaryClockSourceThe secondary clock source, configurable for ACCESS radios only.rw Enumeration .1.3.6.1.4.1.2281.3.4.1.4 |
gnSSMCfgSecondaryClockQualityThis parameter indicates the secondary clock quality.
Possible values for SDH:
PRC(1), SSUT(2), SSUL(3), SEC(4), STU(5).
Possible values for Sonet:
PRS(1), STU(2), ST2(3), ST3(4), SMC(5), ST4(6).rw INTEGER .1.3.6.1.4.1.2281.3.4.1.5 |
gnSSMCfgClockUserCommandThe clock user command.
Switch is possible only when the SSM mode is disable.rw Enumeration .1.3.6.1.4.1.2281.3.4.1.6 |
gnSSMCfgClockOutputMuteThis parameter indicates if clock output will be in mute state.
(Mute on -> don't transmit)rw Enumeration .1.3.6.1.4.1.2281.3.4.1.7 |
gnSSMStat OBJECT IDENTIFIER .1.3.6.1.4.1.2281.3.4.2 |
gnSSMStatStatusAlarm status of SSM. Bit 1 is MSB, bit=1 when alarm active.
bit 1 = Unlock
bit 2 = Out Of Range
bit 3 = Primary Clock Source Failure
bit 4 = Secondary Clock Source Failurero OCTET STRING .1.3.6.1.4.1.2281.3.4.2.1 |
gnSSMStatCurrentClockro Enumeration .1.3.6.1.4.1.2281.3.4.2.2 |
gnSSMStatCurrentClockQualityThis parameter indicates the current clock quality.
SDH values: PRC(1), SSUT(2), SSUL(3), SEC(4), STU(5), DNU(6).
Sonet values: PRS(1), STU(2), ST2(3), ST3(4), SMC(5), ST4(6), DUS(7).ro INTEGER .1.3.6.1.4.1.2281.3.4.2.3 |
gnSSMStatClockUnitTypero Enumeration .1.3.6.1.4.1.2281.3.4.2.4 |
gnSSMStatHoldoverPeriodThis parameter indicates the minutes time period in holdover state.ro INTEGER .1.3.6.1.4.1.2281.3.4.2.5 |
gnAccess OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4 |
gnAccessCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.1 |
gnAccessCfgTableThis table defines the configuration and status of the access ports. SEQUENCE OF GnAccessCfgEntry .1.3.6.1.4.1.2281.4.1.1 |
gnAccessCfgEntryEntry for the table containing an interface index for every interface
which type is DS3 (30, according to RFC1573). GnAccessCfgEntry .1.3.6.1.4.1.2281.4.1.1.1 |
gnAccessCfgLongCableOptionThis parameter defines the line build-out option.
Possible values:
For DS3: ds3ShortCable, ds3LongCable.
For T1: t1From0to133ft..t1From533to655ft.
For E1/E3: anyLength.
For T1 in FIBEAIR 640 systems: t1FA640From0to110ft..t1FA640From440to550ft.rw Enumeration .1.3.6.1.4.1.2281.4.1.1.1.1 |
gnAccessCfgLoopbackOptionThis parameter enable the user to launch a loopback.rw Enumeration .1.3.6.1.4.1.2281.4.1.1.1.2 |
gnAccessCfgRunPrbsThis parameter enables launching a PRBS test.rw Enumeration .1.3.6.1.4.1.2281.4.1.1.1.3 |
gnAccessCfgEXCThreshIf the bit error rate is higher than this threshold
an EXC alarm would be generated.
EXC is for excessive.rw Enumeration .1.3.6.1.4.1.2281.4.1.1.1.4 |
gnAccessCfgSDThreshIf the bit error rate is higher than this threshold
a SD alarm would be generated.
SD is for Signal Degrade.rw Enumeration .1.3.6.1.4.1.2281.4.1.1.1.5 |
gnAccessCfgTestThis parameter controls the action to send AIS or not.rw Enumeration .1.3.6.1.4.1.2281.4.1.1.1.6 |
gnAccessCfgLineCodingThe line coding possible values:
For T1: B7ZS(ami), B8ZS.
For E1 & E3: HDB3.
For DS3: B3ZSrw Enumeration .1.3.6.1.4.1.2281.4.1.1.1.7 |
gnAccessStat OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.2 |
gnAccessStatTableThis table defines the status of the access ports. SEQUENCE OF GnAccessStatEntry .1.3.6.1.4.1.2281.4.2.1 |
gnAccessStatEntryEntry for the table containing an interface index for every interface
which type is DS3 (30, according to RFC1573). GnAccessStatEntry .1.3.6.1.4.1.2281.4.2.1.1 |
gnAccessStatInterfaceBerCurrent Bit Error Rate.ro Enumeration .1.3.6.1.4.1.2281.4.2.1.1.1 |
gnAccessStatStatusAlarm status of an ACCESS radio. Bit 1 is MSB, bit=1 when alarm active.
bit 2 = LOS
bit 6 = AIS
bit 9 = SD
bit 10 = EXC
bit 11 = Unexpected signal
bit 14 = Out Of Lockro OCTET STRING .1.3.6.1.4.1.2281.4.2.1.1.2 |
gnAccessStatPrbsBerCurrent PRBS Errors of the operation set
in the mib variable gnAccessCfgRunPrbs,
use this variable to clear the error counter.ro Enumeration .1.3.6.1.4.1.2281.4.2.1.1.3 |
gnAccessStatValidIntervalsThe number of previous valid intervals for which valid data has been stored
for the specific interface.ro INTEGER .1.3.6.1.4.1.2281.4.2.1.1.4 |
gnFastEthernetCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.3 |
gnFastEthernetCfgTableThis table defines the configuration of the Fast Ethernet ports. SEQUENCE OF GnFastEthernetCfgEntry .1.3.6.1.4.1.2281.4.3.1 |
gnFastEthernetCfgEntryThis is an entry in the Fast Ethernet configuration table. GnFastEthernetCfgEntry .1.3.6.1.4.1.2281.4.3.1.1 |
gnFastEthernetCfgAutoNegotiationThis parameter defines if auto negotiations protocol is active.rw Enumeration .1.3.6.1.4.1.2281.4.3.1.1.1 |
gnFastEthernetCfgForceSpeedThis parameter force speed when auto negotiation is off.rw Enumeration .1.3.6.1.4.1.2281.4.3.1.1.2 |
gnFastEthernetCfgDynamicBandDynamic bandwidth allocation:
dynamic means that the two Fast Ethernet ports have the same priority.
LeftPreferred indicates that left Fast Ethernet card priority is higher.rw Enumeration .1.3.6.1.4.1.2281.4.3.1.1.3 |
gnFastEthernetCfgGigabitEthernetGigabit Ethernet option.
This parameter will be changed after reset.rw Enumeration .1.3.6.1.4.1.2281.4.3.1.1.4 |
gnFastEthernetCfgDuplexModeThis parameter force duplex mode when auto negotiation is off.rw Enumeration .1.3.6.1.4.1.2281.4.3.1.1.5 |
gnFastEthernetCfgQueuingSchemeThis parameter set the Queuing algorithm.rw Enumeration .1.3.6.1.4.1.2281.4.3.1.1.6 |
gnFastEthernetStat OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.4 |
gnFastEthernetStatTableThe Fast Ethernet status table. SEQUENCE OF GnFastEthernetStatEntry .1.3.6.1.4.1.2281.4.4.1 |
gnFastEthernetStatEntryThis is an entry in the Fast Ethernet status table. GnFastEthernetStatEntry .1.3.6.1.4.1.2281.4.4.1.1 |
gnFastEthernetStatStatusAlarm status of an FE radio. Bit 1 is MSB, bit=1 when alarm active.
bit 2 = Loss of Carrierro OCTET STRING .1.3.6.1.4.1.2281.4.4.1.1.1 |
gnPdhMon OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.5 |
gnPdhMonCurrTableThis table maintains the counters for the PDH table. SEQUENCE OF GnPdhMonCurrEntry .1.3.6.1.4.1.2281.4.5.1 |
gnPdhMonCurrEntryThis is an entry in the PDH
Counters Table. This table contains an interface index for every interface
which type is DS3(30, according to RFC1573). GnPdhMonCurrEntry .1.3.6.1.4.1.2281.4.5.1.1 |
gnPdhMonCurrESThe current number of errored seconds starting from the present 15 minute
period. .ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.1 |
gnPdhMonCurrSESThe current number of severely errored seconds, starting from the present
15 minute period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.2 |
gnPdhMonCurrBBEThe current number of Background Block Errors
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.3 |
gnPdhMonCurrUASThe current number of Unavailable Seconds
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.4 |
gnPdhMonCurrCVThe current number of CV
starting from the present 15 minutes period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.5 |
gnPdhMonCurrLastDayESThe current number of Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.6 |
gnPdhMonCurrLastDaySESThe current number of Severely Errored Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.7 |
gnPdhMonCurrLastDayBBEThe current number of Background Block Errors
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.8 |
gnPdhMonCurrLastDayUASThe current number of Unavailable Seconds
starting from the present 24 hours period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.9 |
gnPdhMonCurrLastDayCVThe current number of CV, starting from the present 24-hour period.ro Gauge .1.3.6.1.4.1.2281.4.5.1.1.10 |
gnPdhMonCurrLastDayIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.4.5.1.1.11 |
gnPdhMonIntervalTableThis table maintains the counters of the PDH per interval. SEQUENCE OF GnPdhMonIntervalEntry .1.3.6.1.4.1.2281.4.5.2 |
gnPdhMonIntervalEntryThis is an entry in the PDH
Counters Table. This table contains an interface index for every interface
which type is DS3(30, according to RFC1573).
This table is indexed by an interval index, between 1
to 96 and representing each one 15 minutes.
The oldest is 96. GnPdhMonIntervalEntry .1.3.6.1.4.1.2281.4.5.2.1 |
gnPdhMonIntervalIdxThis table is indexed per interval number. Each interval
is of 15 minutes and the oldest is 96.ro INTEGER .1.3.6.1.4.1.2281.4.5.2.1.1 |
gnPdhMonIntervalESThe number of errored seconds per interval.ro Gauge .1.3.6.1.4.1.2281.4.5.2.1.2 |
gnPdhMonIntervalSESThe number of severely errored seconds per interval.ro Gauge .1.3.6.1.4.1.2281.4.5.2.1.3 |
gnPdhMonIntervalBBEThe number of Background Block Errors
per interval.ro Gauge .1.3.6.1.4.1.2281.4.5.2.1.4 |
gnPdhMonIntervalUASThe number of Unavailable Seconds per interval.ro Gauge .1.3.6.1.4.1.2281.4.5.2.1.5 |
gnPdhMonIntervalCVThe number of CV per interval.ro Gauge .1.3.6.1.4.1.2281.4.5.2.1.6 |
gnPdhMonIntervalIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.4.5.2.1.7 |
gnPdhMonDayTableThis table maintains the counters of the PDH per 24 hours interval. SEQUENCE OF GnPdhMonDayEntry .1.3.6.1.4.1.2281.4.5.3 |
gnPdhMonDayEntryThis is an entry in the PDH
Counters Table. This table contains an interface index for every interface
which type is DS3(30, according to RFC1573).
This table is indexed by an interval index, between 1
to 30 and representing each one 24 hours.
The oldest is 30. GnPdhMonDayEntry .1.3.6.1.4.1.2281.4.5.3.1 |
gnPdhMonDayIdxThis table is indexed per interval number. Each interval
is of 24 hours and the oldest is 30.ro INTEGER .1.3.6.1.4.1.2281.4.5.3.1.1 |
gnPdhMonDayESThe number of Errored Seconds per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.4.5.3.1.2 |
gnPdhMonDaySESThe number of Severely Errored Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.4.5.3.1.3 |
gnPdhMonDayBBEThe number of Background Block Errors
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.4.5.3.1.4 |
gnPdhMonDayUASThe number of Unavailable Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.4.5.3.1.5 |
gnPdhMonDayCVThe number of Code Violation Seconds
per interval of 24 hours.ro Gauge .1.3.6.1.4.1.2281.4.5.3.1.6 |
gnPdhMonDayIDFIDF = Invalid Data Flag.ro Enumeration .1.3.6.1.4.1.2281.4.5.3.1.7 |
gnFastEthernetMon OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.6 |
gnFastEthernetMonPrivateTableThe Fast Ethernet Private Statistics Table. SEQUENCE OF GnFastEthernetMonPrivateEntry .1.3.6.1.4.1.2281.4.6.1 |
gnFastEthernetMonPrivateEntryThis is an entry in the Fast Ethernet private statistics table. GnFastEthernetMonPrivateEntry .1.3.6.1.4.1.2281.4.6.1.1 |
gnFastEthernetMonPrivateAlignmentErrorsThe number of received packets with an alignment
error (Received frame length is not a multiple
of 8 bits, and an FCS error had occurred).ro Counter .1.3.6.1.4.1.2281.4.6.1.1.1 |
gnFastEthernetMonPrivateFcsErrorsTotal number of received packets with a frame check
sequence (FCS) or Cycle Redundancy Check (CRC) error.ro Counter .1.3.6.1.4.1.2281.4.6.1.1.2 |
gnFastEthernetMonPrivateFrameTooLongsTotal number of received frames with an illegal
packet length (>1518 bytes).ro Counter .1.3.6.1.4.1.2281.4.6.1.1.3 |
gnFastEthernetMonStdHiTableThis table contains the 32 high bits (MSB) of RFC1213 statistics
for Fast Ethernet. SEQUENCE OF GnFastEthernetMonStdHiEntry .1.3.6.1.4.1.2281.4.6.2 |
gnFastEthernetMonStdHiEntryThis is an entry in the Fast Ethernet
Standard Statistics Table. GnFastEthernetMonStdHiEntry .1.3.6.1.4.1.2281.4.6.2.1 |
gnFastEthernetMonStdHiInOctetsHCThe 32 MSB of The total number of octets received
on the interface, including framing characters.ro Counter .1.3.6.1.4.1.2281.4.6.2.1.1 |
gnFastEthernetMonStdHiInUcastPktsHCThe 32 MSB of The number of subnetwork-unicast
packets delivered to a higher-layer protocol.ro Counter .1.3.6.1.4.1.2281.4.6.2.1.2 |
gnFastEthernetMonStdHiInNUcastPktsHCThe 32 MSB of The number of non-unicast
(i.e., subnetwork- broadcast or subnetwork-multicast)
packets delivered to a higher-layer protocol.ro Counter .1.3.6.1.4.1.2281.4.6.2.1.3 |
gnFastEthernetMonStdHiOutOctetsHCThe 32 MSB of The total number of octets transmitted
out of the interface, including framing characters.ro Counter .1.3.6.1.4.1.2281.4.6.2.1.4 |
gnFastEthernetMonStdHiOutUcastPktsHCThe 32 MSB of The total number of packets that
higher-level protocols requested be transmitted
to a subnetwork-unicast address, including those
that were discarded or not sent.ro Counter .1.3.6.1.4.1.2281.4.6.2.1.5 |
gnFastEthernetMonStdHiOutNUcastPktsHCThe 32 MSB of The total number of packets that
higher-level protocols requested be transmitted
to a non- unicast (i.e., a subnetwork-broadcast
or subnetwork-multicast) address, including those
that were discarded or not sent.ro Counter .1.3.6.1.4.1.2281.4.6.2.1.6 |
gnTrailCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.7 |
gnTrailCfgTableThis table defines the configuration of the trail ports. SEQUENCE OF GnTrailCfgEntry .1.3.6.1.4.1.2281.4.7.1 |
gnTrailCfgEntry GnTrailCfgEntry .1.3.6.1.4.1.2281.4.7.1.1 |
gnTrailCfgTrailNamerw DisplayString .1.3.6.1.4.1.2281.4.7.1.1.1 |
gnTrailCfgProtectionrw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.2 |
gnTrailCfgLowPathIndexThis parameter indicates the K.L.M index.
It includes 3 digits:
K - most significant digit, L - next digit,
M - last significant digit.
For E1 ports (SDH): K=1..3 ; L=1..7 ; M=1..3.
For T1 ports (Sonet): K=1..3 ; L=1..7 ; M=1..4.
For DS3/E3: K=1..3 ; L=M=0.
If there is no K.L.M index: K=L=M=0.
Example: for mapping an E1 port to K.L.M = 2.5.3, write 253.rw INTEGER .1.3.6.1.4.1.2281.4.7.1.1.3 |
gnTrailCfgLowPathSiderw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.4 |
gnTrailCfgProtectionOptionsrw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.5 |
gnTrailCfgMismatchJ2In case of J2 mismatch error, send alarm or send AIS.rw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.6 |
gnTrailCfgTransmittedJ2This is the J2 string that would be sent.rw DisplayString .1.3.6.1.4.1.2281.4.7.1.1.7 |
gnTrailCfgExpectedJ2This is the J2 string that is expected to be received.rw DisplayString .1.3.6.1.4.1.2281.4.7.1.1.8 |
gnTrailCfgReversionModerw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.9 |
gnTrailCfgProtectionUserCommandrw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.10 |
gnTrailCfgHoldOffTimeThis is the hold-off time in milliseconds.
Possible values: 0..20000, 100 mSec steps.rw INTEGER .1.3.6.1.4.1.2281.4.7.1.1.11 |
gnTrailCfgOscillationGuardTimeThis is the oscillation guard time in seconds.
Possible values: 0..60.rw INTEGER .1.3.6.1.4.1.2281.4.7.1.1.12 |
gnTrailCfgWaitToRestoreTimeThis is the wait-to-restore time in minutes.
Possible values: 5..12.rw INTEGER .1.3.6.1.4.1.2281.4.7.1.1.13 |
gnTrailCfgSignalLabelMismatchIn case of a V5 mismatch error, send or don't send AIS.rw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.14 |
gnTrailCfgBERConsActionrw Enumeration .1.3.6.1.4.1.2281.4.7.1.1.15 |
gnTribCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.8 |
gnTribCfgTableThis table defines the configuration of the virtual trails in the Trib STM-1. SEQUENCE OF GnTribCfgEntry .1.3.6.1.4.1.2281.4.8.1 |
gnTribCfgEntry GnTribCfgEntry .1.3.6.1.4.1.2281.4.8.1.1 |
gnTribCfgLowPathIndexThis parameter indicates the K.L.M index.
It includes 3 digits:
K - most significant digit, L - next digit,
M - last significant digit.
For E1 ports (SDH): K=1..3 ; L=1..7 ; M=1..3.
For T1 ports (Sonet): K=1..3 ; L=1..7 ; M=1..4.
For DS3/E3: K=1..3 ; L=M=0.
If there is no K.L.M index: K=L=M=0.
Example: for mapping an E1 port to K.L.M = 2.5.3, write 253.rw INTEGER .1.3.6.1.4.1.2281.4.8.1.1.1 |
gnTribCfgLowPathSiderw Enumeration .1.3.6.1.4.1.2281.4.8.1.1.2 |
gnTribCfgProtectionrw Enumeration .1.3.6.1.4.1.2281.4.8.1.1.3 |
gnTribCfgProtectionOptionsrw Enumeration .1.3.6.1.4.1.2281.4.8.1.1.4 |
gnTribCfgReversionModerw Enumeration .1.3.6.1.4.1.2281.4.8.1.1.5 |
gnTribCfgProtectionUserCommandrw Enumeration .1.3.6.1.4.1.2281.4.8.1.1.6 |
gnTribCfgHoldOffTimeThis is the hold-off time in milliseconds.
Possible values: 0..20000, 100 mSec steps.rw INTEGER .1.3.6.1.4.1.2281.4.8.1.1.7 |
gnTribCfgOscillationGuardTimeThis is the oscillation guard time in seconds.
Possible values: 0..60.rw INTEGER .1.3.6.1.4.1.2281.4.8.1.1.8 |
gnTribCfgWaitToRestoreTimeThis is the wait-to-restore time in minutes.
Possible values: 5..12.rw INTEGER .1.3.6.1.4.1.2281.4.8.1.1.9 |
gnTribCfgKLMrw INTEGER .1.3.6.1.4.1.2281.4.8.1.1.10 |
gnTrailPassThrough OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.9 |
gnTrailPassThroughTableThis table defines the configuration of the virtual trails in the Trib STM-1. It is applicable for ADM SEQUENCE OF GnTrailPassThroughEntry .1.3.6.1.4.1.2281.4.9.1 |
gnTrailPassThroughEntry GnTrailPassThroughEntry .1.3.6.1.4.1.2281.4.9.1.1 |
gnTrailPassThroughIndexThis is the index of Trail Pass-Through Table. SDH(1-63), Sonet (1-84).ro INTEGER .1.3.6.1.4.1.2281.4.9.1.1.1 |
gnTrailPassThroughNamefor NMS userw DisplayString .1.3.6.1.4.1.2281.4.9.1.1.2 |
gnGigabitEthernetCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2281.4.10 |
gnGigabitEthernetCfgTableThis table defines the configuration of the Gigabit Ethernet port. SEQUENCE OF GnGigabitEthernetCfgEntry .1.3.6.1.4.1.2281.4.10.1 |
gnGigabitEthernetCfgEntryThis is an entry in the Gigabit Ethernet configuration table. GnGigabitEthernetCfgEntry .1.3.6.1.4.1.2281.4.10.1.1 |
gnGigabitEthernetCfgFlowControlThis parameter defines if flow control protocol is active.rw Enumeration .1.3.6.1.4.1.2281.4.10.1.1.1 |
gnGigabitEthernetCfgMuteOnExcErrorThis parameter defines whether to mute GBE Tx on excessive BER.rw Enumeration .1.3.6.1.4.1.2281.4.10.1.1.2 |
gnGigabitEthernetCfgMuteOnSdThis parameter defines whether to mute GBE Tx port on signal degrade.rw Enumeration .1.3.6.1.4.1.2281.4.10.1.1.3 |
gnGigabitEthernetCfgMuteOnRemoteRadioFaultThis parameter defines whether to mute GBE Tx port on exe error.rw Enumeration .1.3.6.1.4.1.2281.4.10.1.1.4 |
gnLastDummy OBJECT IDENTIFIER .1.3.6.1.4.1.2281.9 |
gnLastDummyParamThis parameter specifies the end of CERAGON's MIB.ro INTEGER .1.3.6.1.4.1.2281.9.1 |
topologiesOptionsGroupTopologyThis value indicates a bitmap :
| 15..12 | 11...........8 | 7........0 |
| Set Id | Group Topology | Group Size |
::= { topologiesOptionsEntry 1 }
topologiesOptionsMembersCarriers OBJECT-TYPE
SYNTAX INTEGER (1)
ACCESS read-only
STATUS mandatory
DESCRIPTIONro INTEGER (1) .linkGroupingEntry.3 |
linkGroupingExtraTrafficAdminThis value indicates the ET adminrw Enumeration .linkGroupingEntry.4 |
linkGroupingGroupNameThis value indicates the groups name.rw DisplayString .linkGroupingEntry.5 |