CAMBIUM-PTP500-MIB
AI MIB Summary
The CAMBIUM-PTP500-MIB enables SNMP-based monitoring and management of Cambium Networks PTP 500 series 105Mbps non-line-of-sight wireless Ethernet bridges, tracking critical operational metrics such as link throughput, signal strength (RSSI/SNR), interface error counters, and device environmental sensors.
MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge.
Main OID:
cambium.1.3.6.1.4.1.17713
221
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
221 total| Object Name |
|---|
cambiumMIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge. MODULE-IDENTITY .1.3.6.1.4.1.17713 |
ptp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.1 |
ptmp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.2 |
ptp500 OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5 |
dfs OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.3 |
dfsTableNumberNumber of entries in the dfsTablero INTEGER .1.3.6.1.4.1.17713.5.3.1 |
dfsTableA table storing a snapshot of various DFS measurements for each channel SEQUENCE OF DfsTableEntry .1.3.6.1.4.1.17713.5.3.2 |
dfsTableEntryTable DfsTable DfsTableEntry .1.3.6.1.4.1.17713.5.3.2.1 |
dfsTableIndexused to index values in the dfsTable. INTEGER .1.3.6.1.4.1.17713.5.3.2.1.1 |
dfsMeansSnapshot of DFS meansro Integer32 .1.3.6.1.4.1.17713.5.3.2.1.2 |
dfsNineNinePointNinePercentilesSnapshot of DFS 99.9 percentilesro Integer32 .1.3.6.1.4.1.17713.5.3.2.1.3 |
dfsPeaksSnapshot of DFS peaksro Integer32 .1.3.6.1.4.1.17713.5.3.2.1.4 |
configuration OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.5 |
iPAddressInternet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute.rw IpAddress .1.3.6.1.4.1.17713.5.5.1 |
subnetMaskA subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attributerw IpAddress .1.3.6.1.4.1.17713.5.5.2 |
gatewayIPAddressThe IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attributerw IpAddress .1.3.6.1.4.1.17713.5.5.3 |
targetMACAddressMAC address of the PTP wireless unit forming the other end of the PTP linkro OCTET STRING .1.3.6.1.4.1.17713.5.5.4 |
masterSlaveModeThe PTP wireless link operates using a master and slave relationshipro Enumeration .1.3.6.1.4.1.17713.5.5.5 |
maximumTransmitPowerMaximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless linkro INTEGER (-100..27) .1.3.6.1.4.1.17713.5.5.6 |
antennaGainAntenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna.rw INTEGER .1.3.6.1.4.1.17713.5.5.7 |
cableLossLoss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.rw INTEGER .1.3.6.1.4.1.17713.5.5.8 |
eIRPEffective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBmro Integer32 .1.3.6.1.4.1.17713.5.5.9 |
channelBandwidthThis control sets the bandwidth of the transmit and receive radio channelsro Enumeration .1.3.6.1.4.1.17713.5.5.11 |
remoteIPAddressIP Address of the peer wireless unitro IpAddress .1.3.6.1.4.1.17713.5.5.12 |
linkNameName of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.ro DisplayString .1.3.6.1.4.1.17713.5.5.14 |
siteNameThis field contains a user-provided description of the site name together with any additional notesrw DisplayString .1.3.6.1.4.1.17713.5.5.15 |
accessMethodThis controls whether the link can be established between pre-paired Master-Slave using MAC addresses (Link Access) or by using link name (Link Name Access)ro Enumeration .1.3.6.1.4.1.17713.5.5.16 |
groupIDWhen Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group. Group Access is only supported on some platformsro INTEGER .1.3.6.1.4.1.17713.5.5.17 |
ethernet OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.6 |
dataPortAutoNegotiationThis controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.rw Enumeration .1.3.6.1.4.1.17713.5.6.1 |
dataPortAutoNegAdvertisementThis sets the different Ethernet configurations that will be advertised during auto negotiation. NB: The new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!rw Bits .1.3.6.1.4.1.17713.5.6.2 |
dataPortAutoMdixThis enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system rebootrw Enumeration .1.3.6.1.4.1.17713.5.6.3 |
dataPortStatusCurrent status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.6.4 |
dataPortSpeedAndDuplexThe current speed and duplex of the Ethernet linkro Enumeration .1.3.6.1.4.1.17713.5.6.5 |
dataPortWirelessDownAlertWhen enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.rw Enumeration .1.3.6.1.4.1.17713.5.6.6 |
useVLANForManagementInterfacesThis controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system rebootrw Enumeration .1.3.6.1.4.1.17713.5.6.7 |
vLANManagementPriorityThis VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system rebootrw INTEGER .1.3.6.1.4.1.17713.5.6.8 |
vLANManagementVIDThis VLAN VID (0-4094) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system rebootrw INTEGER .1.3.6.1.4.1.17713.5.6.11 |
vLANPriorityTableNumberNumber of entries in the vLANPriorityTable.ro INTEGER (9) .1.3.6.1.4.1.17713.5.6.14 |
vLANPriorityTableA priority queue mapping table. This is a list of packet queues indexed by VLAN priority. SEQUENCE OF VLANPriorityTableEntry .1.3.6.1.4.1.17713.5.6.15 |
vLANPriorityTableEntryTable VLANPriorityTable VLANPriorityTableEntry .1.3.6.1.4.1.17713.5.6.15.1 |
vLANPriorityQueueMappingMapping of VLAN priority flag to packet queue. The higher the queue number the greater its priority.rw Enumeration .1.3.6.1.4.1.17713.5.6.15.1.1 |
vLANPriorityTableIndexVLAN priority flag, used to index values in the vLANPriorityTable. Enumeration .1.3.6.1.4.1.17713.5.6.15.1.2 |
telecom OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.7 |
telecomsInterfaceThe line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored.ro Enumeration .1.3.6.1.4.1.17713.5.7.1 |
telecomsChannelStatusCurrent status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.7.2 |
telecomsLineCodeThe line code setting of the telecoms interface. This must match the setting of the device connected to this interfacero Enumeration .1.3.6.1.4.1.17713.5.7.4 |
telecomsCableLengthThe length of the cable connected to the telecoms interface, measured in feetro Enumeration .1.3.6.1.4.1.17713.5.7.6 |
telecomsLoopbackThe loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.7.8 |
licence OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.8 |
regionCodeThe region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.8.1 |
productVariantThe product variantro Enumeration .1.3.6.1.4.1.17713.5.8.2 |
productNameName of the product variantro DisplayString .1.3.6.1.4.1.17713.5.8.3 |
ethernetFiberSupportEthernet fiber support availability on this wireless unitro Enumeration .1.3.6.1.4.1.17713.5.8.4 |
frequencyVariantFrequency variant of the wireless unitro Enumeration .1.3.6.1.4.1.17713.5.8.5 |
bandwidthVariantBandwidth variant of the wireless unitro Enumeration .1.3.6.1.4.1.17713.5.8.6 |
constantPowerSpectralDensityConstant power spectral density mode controlro Enumeration .1.3.6.1.4.1.17713.5.8.7 |
sNMPv3EnableSNMPv3 availability controlro Enumeration .1.3.6.1.4.1.17713.5.8.9 |
licensedCapacityMaximum allowable data rate for ethernet frames permitted by the licence key. The actual data rate depends upon the prevailing wireless conditionsro Enumeration .1.3.6.1.4.1.17713.5.8.11 |
management OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.9 |
installStatusA non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.9.3 |
installArmStateIndicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.9.4 |
tFTPServerIPAddressIP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedrw IpAddress .1.3.6.1.4.1.17713.5.9.5 |
tFTPServerPortNumberThe port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedrw INTEGER .1.3.6.1.4.1.17713.5.9.6 |
tFTPSoftwareUpgradeFileNameFilename of the Software Upgrade to be loaded from the TFTP Serverrw DisplayString .1.3.6.1.4.1.17713.5.9.7 |
tFTPStartSoftwareUpgradeWrite '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finishedrw Integer32 .1.3.6.1.4.1.17713.5.9.8 |
tFTPSoftwareUpgradeStatusThe current status of the TFTP Software upgrade processro Enumeration .1.3.6.1.4.1.17713.5.9.9 |
tFTPSoftwareUpgradeStatusTextDescriptive text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.5.9.10 |
tFTPSoftwareUpgradeStatusAdditionalTextAny additional text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.5.9.11 |
hTTPAccessEnabledThis controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)rw Enumeration .1.3.6.1.4.1.17713.5.9.12 |
telnetAccessEnabledThis controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)rw Enumeration .1.3.6.1.4.1.17713.5.9.13 |
hTTPPortNumberThis controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)rw INTEGER .1.3.6.1.4.1.17713.5.9.14 |
hTTPSPortNumberThis controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the Licence Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)rw INTEGER .1.3.6.1.4.1.17713.5.9.15 |
telnetPortNumberThis controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)rw INTEGER .1.3.6.1.4.1.17713.5.9.16 |
hTTPSAccessEnabledThis controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)rw Enumeration .1.3.6.1.4.1.17713.5.9.17 |
phyControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.10 |
linkSymmetryIn fixed asymmetric mode (3 to 1) the transmit time is three times as long as the receive time. In fixed symmetric mode (1 to 1) the unit spends an equal amount of time transmitting and receiving. In fixed asymmetric mode (1 to 3) the receive time is three times as long as the transmit time. In adaptive mode the transmit and receive periods adjust with applied load. NB: only applicable for master nodes.ro Enumeration .1.3.6.1.4.1.17713.5.10.1 |
linkModeOptimisationOptimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols.ro Enumeration .1.3.6.1.4.1.17713.5.10.2 |
userConfiguredMaxModulationModeThe maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizardrw Enumeration .1.3.6.1.4.1.17713.5.10.3 |
remoteMaximumTransmitPowerMaximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless linkro INTEGER (-100..27) .1.3.6.1.4.1.17713.5.10.4 |
phyStatus OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.12 |
receivePowerReceive power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.5.12.1 |
vectorErrorThe vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.5.12.2 |
transmitPowerTransmit power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.5.12.3 |
rangeDistance between the two peer wireless units expressed in tenths of a kilometerro Integer32 .1.3.6.1.4.1.17713.5.12.4 |
linkLossThe wireless link loss expressed in tenths of a dBro INTEGER (-500..500) .1.3.6.1.4.1.17713.5.12.5 |
receiveChannelCurrent active receive channelro INTEGER .1.3.6.1.4.1.17713.5.12.6 |
transmitChannelCurrent active transmit channelro INTEGER .1.3.6.1.4.1.17713.5.12.7 |
receiveModulationModeCurrent active receive modulation modero Enumeration .1.3.6.1.4.1.17713.5.12.8 |
transmitModulationModeCurrent active transmit modulation modero Enumeration .1.3.6.1.4.1.17713.5.12.9 |
receiveFreqMHzCurrent receive frequency expressed in integer MHzro INTEGER .1.3.6.1.4.1.17713.5.12.11 |
transmitFreqMHzCurrent transmit frequency expressed in integer MHzro INTEGER .1.3.6.1.4.1.17713.5.12.12 |
signalStrengthRatioSignal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.5.12.13 |
receiveFreqKHzCurrent receive frequency expressed as KHzro INTEGER .1.3.6.1.4.1.17713.5.12.14 |
transmitFreqKHzCurrent transmit frequency expressed as KHzro INTEGER .1.3.6.1.4.1.17713.5.12.15 |
searchStateSearch status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.ro Enumeration .1.3.6.1.4.1.17713.5.12.16 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.13 |
unitOutOfCalibrationThe unit is out of calibrationro Enumeration .1.3.6.1.4.1.17713.5.13.1 |
incompatibleRegionCodesThe master and slave units have incompatible region codes. NB: Both units must have compatible licence keysro Enumeration .1.3.6.1.4.1.17713.5.13.4 |
noWirelessChannelAvailableSpectrum Management was unable to locate a suitable wireless channel to operate onro Enumeration .1.3.6.1.4.1.17713.5.13.5 |
wirelessLinkDisabledWarningThe SNMP ifAdminStatus of the wireless interface has disabled wireless trafficro Enumeration .1.3.6.1.4.1.17713.5.13.6 |
dataPortDisabledWarningThe SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet trafficro Enumeration .1.3.6.1.4.1.17713.5.13.7 |
dataPortConfigurationMismatchThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatchro Enumeration .1.3.6.1.4.1.17713.5.13.9 |
incompatibleMasterAndSlaveA non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.13.10 |
tDDSynchronizationStatusAn alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference.ro Enumeration .1.3.6.1.4.1.17713.5.13.11 |
tDDSynchronizationAlarmNot Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.ro Enumeration .1.3.6.1.4.1.17713.5.13.13 |
linkModeOptimizationMismatchThe remote node of this link has been configured with a different link mode optimizationro Enumeration .1.3.6.1.4.1.17713.5.13.14 |
capacityLicenseMismatchThe local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unitro Enumeration .1.3.6.1.4.1.17713.5.13.16 |
smtp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.15 |
sMTPEmailAlertSimple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address. This utility can only be configured by the system administratorrw Enumeration .1.3.6.1.4.1.17713.5.15.1 |
sMTPServerIPAddressIP address of the SMTP serverrw IpAddress .1.3.6.1.4.1.17713.5.15.2 |
sMTPServerPortNumberPort number of the SMTP serverrw INTEGER .1.3.6.1.4.1.17713.5.15.3 |
sMTPSourceEmailAddressThe 'from' email address used when constructing the automatically generated e-mail messagerw DisplayString .1.3.6.1.4.1.17713.5.15.4 |
sMTPDestinationEmailAddressThe 'to' email address used when constructing the automatically generated e-mail messagerw DisplayString .1.3.6.1.4.1.17713.5.15.5 |
sMTPEnabledMessagesThis controls which SMTP messages the unit will sendrw Bits .1.3.6.1.4.1.17713.5.15.6 |
snmpControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.16 |
sNMPPortNumberThe IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attributerw INTEGER .1.3.6.1.4.1.17713.5.16.1 |
sNMPCommunityStringThe SNMP community string. NB: A system reboot is required to activate changes to this attributerw DisplayString .1.3.6.1.4.1.17713.5.16.2 |
sNMPTrapTableNumberNumber of entries in the sNMPTrapTable.ro INTEGER (2) .1.3.6.1.4.1.17713.5.16.3 |
sNMPTrapTableSNMP trap configuration table. SEQUENCE OF SNMPTrapTableEntry .1.3.6.1.4.1.17713.5.16.4 |
sNMPTrapTableEntryTable SNMPTrapTable SNMPTrapTableEntry .1.3.6.1.4.1.17713.5.16.4.1 |
sNMPTrapTableIndexSNMP trap value, used to index the SNMPTrapTable. INTEGER .1.3.6.1.4.1.17713.5.16.4.1.1 |
sNMPTrapIPAddressThe IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute.rw IpAddress .1.3.6.1.4.1.17713.5.16.4.1.2 |
sNMPTrapPortNumberDestination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute.rw INTEGER .1.3.6.1.4.1.17713.5.16.4.1.3 |
sNMPTrapVersionThe SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attributerw Enumeration .1.3.6.1.4.1.17713.5.16.5 |
sNMPEnabledTrapsThis controls which SNMP Traps the unit will sendrw Bits .1.3.6.1.4.1.17713.5.16.6 |
enabledDiagnosticAlarmsControls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributesrw Bits .1.3.6.1.4.1.17713.5.16.7 |
sNMPSendAllTrapsAtStartupControls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up.rw Enumeration .1.3.6.1.4.1.17713.5.16.8 |
sntp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.17 |
sNTPStateSNTP control staterw Enumeration .1.3.6.1.4.1.17713.5.17.1 |
sNTPServerIPAddressThe IP address of a valid SNTP serverrw IpAddress .1.3.6.1.4.1.17713.5.17.2 |
sNTPServerPortNumberThe IP port number of the SNTP server. Defaults to port 123.rw INTEGER .1.3.6.1.4.1.17713.5.17.3 |
sNTPPollIntervalThe SNTP server polling intervalrw INTEGER .1.3.6.1.4.1.17713.5.17.4 |
sNTPSyncIf SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.5.17.5 |
sNTPLastSyncLast SNTP sync timero Integer32 .1.3.6.1.4.1.17713.5.17.6 |
systemClockSystem clock presented as local timero Integer32 .1.3.6.1.4.1.17713.5.17.7 |
timeZoneTime zone offsets from Greenwich Mean Time (GMT)rw Enumeration .1.3.6.1.4.1.17713.5.17.8 |
daylightSavingDaylight Saving Timerw Enumeration .1.3.6.1.4.1.17713.5.17.9 |
reset OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.18 |
systemResetSetting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memoryrw Enumeration .1.3.6.1.4.1.17713.5.18.1 |
versions OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.19 |
softwareVersionCurrent software versionro DisplayString .1.3.6.1.4.1.17713.5.19.1 |
hardwareVersionHardware platform versionro DisplayString .1.3.6.1.4.1.17713.5.19.2 |
secondarySoftwareVersionSecondary software version, used when the primary software image is invalid or erasedro DisplayString .1.3.6.1.4.1.17713.5.19.3 |
bootVersionBoot code software versionro DisplayString .1.3.6.1.4.1.17713.5.19.4 |
pubStats OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.20 |
receiveDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.5.20.1 |
transmitDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.5.20.2 |
aggregateDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.5.20.3 |
wirelessLinkAvailabilityLink availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precisionro INTEGER .1.3.6.1.4.1.17713.5.20.4 |
wirelessLinkStatusCurrent status of the wireless linkro Enumeration .1.3.6.1.4.1.17713.5.20.5 |
byteErrorRatioReciprocal of the byte error ratio calculated since the last reset of the system countersro Integer32 .1.3.6.1.4.1.17713.5.20.6 |
receiveModulationModeDetailThe reason for the current receive modulation modero Enumeration .1.3.6.1.4.1.17713.5.20.7 |
encryption OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.22 |
encryptionAlgorithmThe Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctlyro Enumeration .1.3.6.1.4.1.17713.5.22.1 |
tDDControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.23 |
tDDSynchronizationModeTDD Synchronization Mode selectionro Enumeration .1.3.6.1.4.1.17713.5.23.1 |
syslogControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.24 |
syslogClientEnable or disable the syslog clientro Enumeration .1.3.6.1.4.1.17713.5.24.1 |
syslogStateThe syslog service has been enabled or disabledro Enumeration .1.3.6.1.4.1.17713.5.24.2 |
aAAControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.25 |
userTableNumberNumber of entries in the userTablero INTEGER .1.3.6.1.4.1.17713.5.25.1 |
userTableThe User Table Control group contains objects specifically for user account management. SEQUENCE OF UserTableEntry .1.3.6.1.4.1.17713.5.25.2 |
userTableEntryTable UserTable UserTableEntry .1.3.6.1.4.1.17713.5.25.2.1 |
userTableIndexused to index values in the userTable. INTEGER .1.3.6.1.4.1.17713.5.25.2.1.1 |
userNameUser name which must be entered, along with the appropriate password, in order to gain access to the system.ro OCTET STRING .1.3.6.1.4.1.17713.5.25.2.1.2 |
userRoleRole of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes.ro Enumeration .1.3.6.1.4.1.17713.5.25.2.1.3 |
userEnabledEnable / Disable the selected userro Enumeration .1.3.6.1.4.1.17713.5.25.2.1.4 |
userPasswordUser password, which must be entered in order to gain access to the system.rw OCTET STRING .1.3.6.1.4.1.17713.5.25.2.1.5 |
supplementary OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.96 |
longitudeThe longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.rw DisplayString .1.3.6.1.4.1.17713.5.96.1 |
latitudeThe latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.rw DisplayString .1.3.6.1.4.1.17713.5.96.2 |
altitudeThe altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function.rw Integer32 .1.3.6.1.4.1.17713.5.96.3 |
ptpComplianceThe compliance statement for the Cambium PTP MIB Unknown .1.3.6.1.4.1.17713.5.97 |
ptpGroups OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.98 |
dfsGroupThe dfs object group. Unknown .1.3.6.1.4.1.17713.5.98.3 |
configurationGroupThe configuration object group. Unknown .1.3.6.1.4.1.17713.5.98.5 |
ethernetGroupThe ethernet object group. Unknown .1.3.6.1.4.1.17713.5.98.6 |
telecomGroupThe telecom object group. Unknown .1.3.6.1.4.1.17713.5.98.7 |
licenceGroupThe licence object group. Unknown .1.3.6.1.4.1.17713.5.98.8 |
managementGroupThe management object group. Unknown .1.3.6.1.4.1.17713.5.98.9 |
phyControlGroupThe phyControl object group. Unknown .1.3.6.1.4.1.17713.5.98.10 |
phyStatusGroupThe phyStatus object group. Unknown .1.3.6.1.4.1.17713.5.98.12 |
alarmsGroupThe alarms object group. Unknown .1.3.6.1.4.1.17713.5.98.13 |
smtpGroupThe smtp object group. Unknown .1.3.6.1.4.1.17713.5.98.15 |
snmpControlGroupThe snmpControl object group. Unknown .1.3.6.1.4.1.17713.5.98.16 |
sntpGroupThe sntp object group. Unknown .1.3.6.1.4.1.17713.5.98.17 |
resetGroupThe reset object group. Unknown .1.3.6.1.4.1.17713.5.98.18 |
versionsGroupThe versions object group. Unknown .1.3.6.1.4.1.17713.5.98.19 |
pubStatsGroupThe pubStats object group. Unknown .1.3.6.1.4.1.17713.5.98.20 |
encryptionGroupThe encryption object group. Unknown .1.3.6.1.4.1.17713.5.98.22 |
tDDControlGroupThe tDDControl object group. Unknown .1.3.6.1.4.1.17713.5.98.23 |
syslogControlGroupThe syslogControl object group. Unknown .1.3.6.1.4.1.17713.5.98.24 |
aAAControlGroupThe aAAControl object group. Unknown .1.3.6.1.4.1.17713.5.98.25 |
supplementaryGroupThe supplementary object group. Unknown .1.3.6.1.4.1.17713.5.98.96 |
notificationsGroupThe notifications group. Unknown .1.3.6.1.4.1.17713.5.98.99 |
ptpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.99 |
ptpTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.17713.5.99.0 |
channelChangeTrapThe PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.1 |
dfsImpulsiveInterferenceTrapDFS impulsive interference detected event NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.2 |
dataPortStatusTrapCurrent status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.3 |
telecomsChannelStatusTrapCurrent status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.4 |
telecomsLoopbackTrapThe loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.6 |
regionCodeTrapThe region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.8 |
installStatusTrapA non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.9 |
installArmStateTrapIndicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.10 |
unitOutOfCalibrationTrapThe unit is out of calibration NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.11 |
incompatibleRegionCodesTrapThe master and slave units have incompatible region codes. NB: Both units must have compatible licence keys NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.14 |
noWirelessChannelAvailableTrapSpectrum Management was unable to locate a suitable wireless channel to operate on NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.15 |
wirelessLinkDisabledWarningTrapThe SNMP ifAdminStatus of the wireless interface has disabled wireless traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.16 |
dataPortDisabledWarningTrapThe SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.17 |
dataPortConfigurationMismatchTrapThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.19 |
incompatibleMasterAndSlaveTrapA non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.20 |
sNTPSyncTrapIf SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.21 |
tDDSynchronizationAlarmTrapNot Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.22 |
linkModeOptimizationMismatchTrapThe remote node of this link has been configured with a different link mode optimization NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.25 |
capacityLicenseMismatchTrapThe local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.27 |
syslogStateTrapThe syslog service has been enabled or disabled NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.30 |
syslogLocalNearlyFullTrapThe syslog local log is nearly full (90%) NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.31 |
syslogLocalWrappedTrapThe syslog local log has wrapped NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.32 |
syslogClientTrapEnable or disable the syslog client NOTIFICATION-TYPE .1.3.6.1.4.1.17713.5.99.0.33 |