CAMBIUM-PTP650-MIB
AI MIB Summary
The CAMBIUM-PTP650-MIB enables monitoring and management of Cambium Networks PTP 650 non-line-of-sight wireless Ethernet bridges via SNMP, exposing critical operational metrics such as link throughput, signal quality (RSSI/SNR), interface statistics, and device health parameters.
MIB for non-line-of-sight (NLOS) wireless ethernet bridge.
Main OID:
cambium.1.3.6.1.4.1.17713
426
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
426 total| Object Name |
|---|
cambiumMIB for non-line-of-sight (NLOS) wireless ethernet bridge. MODULE-IDENTITY .1.3.6.1.4.1.17713 |
ptp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.1 |
ptmp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.2 |
ptp650 OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7 |
dfs OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.3 |
dfsTableNumberNumber of entries in the dfsTablero INTEGER .1.3.6.1.4.1.17713.7.3.1 |
dfsTableA table storing a snapshot of various DFS measurements for each channel SEQUENCE OF DfsTableEntry .1.3.6.1.4.1.17713.7.3.2 |
dfsTableEntryTable DfsTable DfsTableEntry .1.3.6.1.4.1.17713.7.3.2.1 |
dfsTableIndexused to index values in the dfsTable. INTEGER .1.3.6.1.4.1.17713.7.3.2.1.1 |
dfsMeansSnapshot of DFS meansro Integer32 .1.3.6.1.4.1.17713.7.3.2.1.2 |
dfsNineNinePointNinePercentilesSnapshot of DFS 99.9 percentilesro Integer32 .1.3.6.1.4.1.17713.7.3.2.1.3 |
dfsPeaksSnapshot of DFS peaksro Integer32 .1.3.6.1.4.1.17713.7.3.2.1.4 |
extendedSpectrumScanningEnables Extended Spectrum Scanningro Enumeration .1.3.6.1.4.1.17713.7.3.3 |
bridge OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.4 |
localPacketFilteringWhen Local Packet Filtering is Enabled, the unit keeps track of the port (Main, SFP, Aux or Wireless) on which a packet with a given MAC source address destined to the management agent has been received. This MAC address to port mapping is then used in order to route any response from the management agent to the right port. When Local Packet Filtering is Disabled, any Ethernet packet from the management agent is sent to all ports.rw Enumeration .1.3.6.1.4.1.17713.7.4.1 |
configuration OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.5 |
iPv4AddressInternet protocol (IPv4) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network.rw IpAddress .1.3.6.1.4.1.17713.7.5.1 |
subnetMaskA subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance.rw IpAddress .1.3.6.1.4.1.17713.7.5.2 |
gatewayIPAddressThe IPv4 address of a device on the current network that acts as an IPv4 network gateway. A gateway acts as an entrance / exit to packets from / to other networksrw IpAddress .1.3.6.1.4.1.17713.7.5.3 |
targetMACAddressMAC address of the PTP wireless unit forming the other end of the PTP linkro OCTET STRING .1.3.6.1.4.1.17713.7.5.4 |
masterSlaveModeThe PTP wireless link operates using a master and slave relationshiprw Enumeration .1.3.6.1.4.1.17713.7.5.5 |
maximumTransmitPowerMaximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link. This may be reduced during installationro INTEGER (-15..30) .1.3.6.1.4.1.17713.7.5.6 |
antennaGainAntenna Gain. Expressed in 10ths of dBi.rw INTEGER .1.3.6.1.4.1.17713.7.5.7 |
cableLossLoss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.rw INTEGER .1.3.6.1.4.1.17713.7.5.8 |
eIRPEffective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBmro Integer32 .1.3.6.1.4.1.17713.7.5.9 |
channelBandwidthThis control sets the bandwidth of the transmit and receive radio channelsro Enumeration .1.3.6.1.4.1.17713.7.5.11 |
linkNameName of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.rw DisplayString .1.3.6.1.4.1.17713.7.5.14 |
siteNameThis field contains a user-provided description of the site name together with any additional notesrw DisplayString .1.3.6.1.4.1.17713.7.5.15 |
accessMethodODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For the Link Access method, each ODU must be configured with Target MAC Address equal to the MAC Address of the other unit. For the Link Name Access method, both units must be configured with the same Link Name. For the Group Access method, both units must be configured with the same Group ID.ro Enumeration .1.3.6.1.4.1.17713.7.5.16 |
groupIDWhen Access Method is set to Group Access, the Group ID identifies all the units belonging to the same grouprw INTEGER .1.3.6.1.4.1.17713.7.5.17 |
iPv6AddressInternet protocol (IPv6) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network.rw DisplayString .1.3.6.1.4.1.17713.7.5.18 |
iPVersionIP protocol selection. Choice of IPv4, IPv6 or Dual.rw Enumeration .1.3.6.1.4.1.17713.7.5.20 |
iPv6AutoConfiguredLinkLocalAddressThe auto configured link local IPv6 addressro DisplayString .1.3.6.1.4.1.17713.7.5.21 |
iPv6PrefixLengthIPv6 prefix lengthrw INTEGER .1.3.6.1.4.1.17713.7.5.22 |
iPv6GatewayAddressThe IPv6 address of a device on the current network that is currently acting as an IPv6 network gateway. A gateway acts as an entrance / exit to packets from / to other networks.rw DisplayString .1.3.6.1.4.1.17713.7.5.23 |
remoteInternetAddressTypeThe type of Internet address specified by the associated remoteInternetAddressType.ro Enumeration .1.3.6.1.4.1.17713.7.5.24 |
remoteInternetAddressINET address used to identify the peer wireless unitro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.17713.7.5.25 |
subbandLowestFrequencyLowest center frequency of the subset of channels.ro Integer32 .1.3.6.1.4.1.17713.7.5.26 |
subbandHighestFrequencyHighest center frequency of the subset of channels.ro Integer32 .1.3.6.1.4.1.17713.7.5.27 |
enableTransmissionControl for enabling/disabling the radio transmitter of the Master. Note: Use Web Properties to control this feature.rw Enumeration .1.3.6.1.4.1.17713.7.5.28 |
ethernet OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.6 |
mainPSUPortAutoNegotiationThis controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.ro Enumeration .1.3.6.1.4.1.17713.7.6.1 |
mainPSUPortAutoNegAdvertisementThis sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!ro Bits .1.3.6.1.4.1.17713.7.6.2 |
mainPSUPortAutoMdixThis enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system rebootro Enumeration .1.3.6.1.4.1.17713.7.6.3 |
mainPSUPortStatusCurrent status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.6.4 |
mainPSUPortSpeedAndDuplexThe current speed and duplex of the Main PSU Ethernet linkro Enumeration .1.3.6.1.4.1.17713.7.6.5 |
dataPortWirelessDownAlertWhen enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.rw Enumeration .1.3.6.1.4.1.17713.7.6.6 |
useVLANForManagementInterfacesThis controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system rebootrw Enumeration .1.3.6.1.4.1.17713.7.6.7 |
vLANManagementPriorityThis VLAN Priority (0-7) will be included in packets generated by the management interfacesrw Enumeration .1.3.6.1.4.1.17713.7.6.8 |
vLANManagementVIDThis VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system rebootrw INTEGER .1.3.6.1.4.1.17713.7.6.11 |
auxPortStatusCurrent status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.6.12 |
auxPortSpeedAndDuplexThe current speed and duplex of the Aux Ethernet linkro Enumeration .1.3.6.1.4.1.17713.7.6.13 |
ethernetPriorityTableNumberNumber of entries in the vLANPriorityTable.ro INTEGER (9) .1.3.6.1.4.1.17713.7.6.14 |
ethernetPriorityTableA priority queue mapping table. This is a list of packet queues indexed by Ethernet priority. SEQUENCE OF EthernetPriorityTableEntry .1.3.6.1.4.1.17713.7.6.15 |
ethernetPriorityTableEntryTable EthernetPriorityTable EthernetPriorityTableEntry .1.3.6.1.4.1.17713.7.6.15.1 |
ethernetPriorityTableIndexEthernet priority flag, used to index values in the ethernetPriorityTable Enumeration .1.3.6.1.4.1.17713.7.6.15.1.1 |
ethernetPriorityQueueMappingConfigures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.7.6.15.1.2 |
l2CPPriorityTableNumberNumber of entries in the l2CPPriorityTable.ro INTEGER (5) .1.3.6.1.4.1.17713.7.6.16 |
l2CPPriorityTableA priority queue mapping table. This is a list of packet queues indexed by L2CP priority. SEQUENCE OF L2CPPriorityTableEntry .1.3.6.1.4.1.17713.7.6.17 |
l2CPPriorityTableEntryTable L2CPPriorityTable L2CPPriorityTableEntry .1.3.6.1.4.1.17713.7.6.17.1 |
l2CPPriorityTableIndexL2CP priority flag, used to index values in the l2CPPriorityTable Enumeration .1.3.6.1.4.1.17713.7.6.17.1.1 |
l2CPPriorityQueueMappingConfigures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.7.6.17.1.2 |
iPDSCPPriorityTableNumberNumber of entries in the iPDSCPPriorityTable.ro INTEGER (64) .1.3.6.1.4.1.17713.7.6.18 |
iPDSCPPriorityTableA priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority. SEQUENCE OF IPDSCPPriorityTableEntry .1.3.6.1.4.1.17713.7.6.19 |
iPDSCPPriorityTableEntryTable IPDSCPPriorityTable IPDSCPPriorityTableEntry .1.3.6.1.4.1.17713.7.6.19.1 |
iPDSCPPriorityTableIndexIP DSCP priority flag, used to index values in the iPDSCPPriorityTable INTEGER .1.3.6.1.4.1.17713.7.6.19.1.1 |
iPDSCPPriorityQueueMappingConfigures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.7.6.19.1.2 |
mPLSTCPriorityTableNumberNumber of entries in the mPLSTCPriorityTable.ro INTEGER (8) .1.3.6.1.4.1.17713.7.6.20 |
mPLSTCPriorityTableA priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority. SEQUENCE OF MPLSTCPriorityTableEntry .1.3.6.1.4.1.17713.7.6.21 |
mPLSTCPriorityTableEntryTable MPLSTCPriorityTable MPLSTCPriorityTableEntry .1.3.6.1.4.1.17713.7.6.21.1 |
mPLSTCPriorityTableIndexMPLS TC priority flag, used to index values in the mPLSTCPriorityTable INTEGER .1.3.6.1.4.1.17713.7.6.21.1.1 |
mPLSTCPriorityQueueMappingConfigures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.7.6.21.1.2 |
managementPortWirelessDownAlertWhen enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.rw Enumeration .1.3.6.1.4.1.17713.7.6.23 |
qOSPrioritySchemeSelects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP and MPLSrw Enumeration .1.3.6.1.4.1.17713.7.6.24 |
unknownNetworkPriorityQueueMappingConfigures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLSrw Enumeration .1.3.6.1.4.1.17713.7.6.25 |
dSCPManagementPriorityThis Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfacesro INTEGER .1.3.6.1.4.1.17713.7.6.26 |
dataBridgingStatusCurrent status of Ethernet Data traffic bridging over the wireless linkro Enumeration .1.3.6.1.4.1.17713.7.6.27 |
mainPSUPortAllocationIndicates the service or services supported by the Main PSU Ethernet portro Enumeration .1.3.6.1.4.1.17713.7.6.28 |
auxPortAllocationIndicates the service or services supported by the Aux Ethernet portro Enumeration .1.3.6.1.4.1.17713.7.6.29 |
sFPPortAllocationIndicates the service or services supported by the SFP Ethernet portro Enumeration .1.3.6.1.4.1.17713.7.6.30 |
dataPortPauseFramesControls whether the bridge tunnels or discards Layer 2 PAUSE frames arriving at the Data Port. Such frames are identified by the destination MAC Address being equal to 01-80-C2-00-00-01ro Enumeration .1.3.6.1.4.1.17713.7.6.31 |
sFPPortAutoNegotiationThis controls whether the local SFP Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.ro Enumeration .1.3.6.1.4.1.17713.7.6.32 |
sFPPortAutoNegAdvertisementThis sets the different SFP Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!ro Bits .1.3.6.1.4.1.17713.7.6.33 |
sFPPortAutoMdixThis enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system rebootro Enumeration .1.3.6.1.4.1.17713.7.6.34 |
sFPPortStatusCurrent status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.6.35 |
sFPPortSpeedAndDuplexThe current speed and duplex of the SFP Ethernet linkro Enumeration .1.3.6.1.4.1.17713.7.6.36 |
auxPortPowerOverEthernetOutputThe state of the Power Over Ethernet (PoE) output of the Aux port. Enabling PoE output may lead to system instability; please refer to the User Guide before enabling this controlro Enumeration .1.3.6.1.4.1.17713.7.6.37 |
auxPortPowerOverEthernetOutputStatusCurrent status of the Power Over Ethernet (PoE) output of the Aux portro Enumeration .1.3.6.1.4.1.17713.7.6.38 |
syncETrackingControls whether Synchronous Ethernet (SyncE) network synchronization is enabled.rw Enumeration .1.3.6.1.4.1.17713.7.6.39 |
syncEEquipmentClockEEC-Option 1 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 2048-kbit/s hierarchy. Corresponds to ITU-T G.813 Option 1; EEC-Option 2 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 1544-kbit/s hierarchy. Corresponds to Type IV clock from ITU-T G.812.rw Enumeration .1.3.6.1.4.1.17713.7.6.40 |
mainPSUPortQLRxOverwriteOverride for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the main PSU port.rw Enumeration .1.3.6.1.4.1.17713.7.6.41 |
mainPSUPortSSMTxControls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Main PSU portrw Enumeration .1.3.6.1.4.1.17713.7.6.42 |
sFPPortSSMTxControls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the SFP portrw Enumeration .1.3.6.1.4.1.17713.7.6.43 |
auxPortSSMTxControls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Aux portrw Enumeration .1.3.6.1.4.1.17713.7.6.44 |
syncETrackingStateThe current state of Synchronous Ethernet (SyncE) network synchronization.ro Enumeration .1.3.6.1.4.1.17713.7.6.45 |
mainPSUPortQLRxThe Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the main PSU port.ro Enumeration .1.3.6.1.4.1.17713.7.6.46 |
auxPortQLRxThe Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the auxiliary port.ro Enumeration .1.3.6.1.4.1.17713.7.6.47 |
sFPPortQLRxThe Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the SFP port.ro Enumeration .1.3.6.1.4.1.17713.7.6.48 |
mainPSUPortQLTxThe Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the main PSU port.ro Enumeration .1.3.6.1.4.1.17713.7.6.49 |
auxPortQLTxThe Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the auxiliary port.ro Enumeration .1.3.6.1.4.1.17713.7.6.50 |
sFPPortQLTxThe Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the SFP port.ro Enumeration .1.3.6.1.4.1.17713.7.6.51 |
mainPSUPortSyncEMasterSlaveStatusThe main PSU port Synchronous Ethernet (SyncE) Master/Slave statusro Enumeration .1.3.6.1.4.1.17713.7.6.52 |
auxPortSyncEMasterSlaveStatusThe auxiliary port Synchronous Ethernet (SyncE) Master/Slave statusro Enumeration .1.3.6.1.4.1.17713.7.6.53 |
sFPPortSyncEMasterSlaveStatusThe SFP port Synchronous Ethernet (SyncE) Master/Slave statusro Enumeration .1.3.6.1.4.1.17713.7.6.54 |
mainPSUPortGigabitMasterSlaveStatusThe main PSU port Gigabit Ethernet Master/Slave statusro Enumeration .1.3.6.1.4.1.17713.7.6.55 |
auxPortGigabitMasterSlaveStatusThe auxiliary port Gigabit Ethernet Master/Slave statusro Enumeration .1.3.6.1.4.1.17713.7.6.56 |
sFPPortGigabitMasterSlaveStatusThe SFP port Gigabit Ethernet Master/Slave statusro Enumeration .1.3.6.1.4.1.17713.7.6.57 |
transparentClockThis control enables the Precision Time Protocol (IEEE-1588) Transparent Clock. Once enabled the unit will modify the correction field in PTP event messages to take account of the time these frames have been resident in this system. This will happen for all PTP frames at Layer 2 & Layer 3 (IPv4 & IPv6) unless a transparent clock VLAN is enabled.rw Enumeration .1.3.6.1.4.1.17713.7.6.58 |
transparentClockVLANIf All is selected then all PTP frames will have their correction fields modified with the residence time. If an S-TAG or C-TAG is selected, only frames with this VLAN tag and matching the VLAN ID in the Transparent Clock VID will have their correction fields modified.rw Enumeration .1.3.6.1.4.1.17713.7.6.59 |
transparentClockVIDThe VLAN ID which frames must match if they are to be corrected. Only valid when an S-TAG or C-TAG has been selected.rw INTEGER .1.3.6.1.4.1.17713.7.6.60 |
mainPSUPortAcceptedQLRxThe Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the main PSU port.ro Enumeration .1.3.6.1.4.1.17713.7.6.61 |
auxPortAcceptedQLRxThe Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the auxiliary port.ro Enumeration .1.3.6.1.4.1.17713.7.6.62 |
sFPPortAcceptedQLRxThe Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the SFP port.ro Enumeration .1.3.6.1.4.1.17713.7.6.63 |
mainPSUPortSyncERxStatusThe Synchronous Ethernet (SyncE) Receive Status of the main PSU portro Enumeration .1.3.6.1.4.1.17713.7.6.64 |
auxPortSyncERxStatusThe Synchronous Ethernet (SyncE) Receive Status of the auxiliary portro Enumeration .1.3.6.1.4.1.17713.7.6.65 |
sFPPortSyncERxStatusThe Synchronous Ethernet (SyncE) Receive Status of the SFP portro Enumeration .1.3.6.1.4.1.17713.7.6.66 |
nIDULanPortStatusCurrent status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.6.67 |
nIDULanPortSpeedAndDuplexThe current speed and duplex of the Ethernet link to the NIDU LAN Portro Enumeration .1.3.6.1.4.1.17713.7.6.68 |
oOBPriorityQueueMappingConfigures the classification of traffic to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.7.6.69 |
nIDULanPortAutoNegotiationThis controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.ro Enumeration .1.3.6.1.4.1.17713.7.6.70 |
nIDULanPortAutoNegAdvertisementThis sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!ro Bits .1.3.6.1.4.1.17713.7.6.71 |
nIDULanPortAutoMdixThis enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system rebootro Enumeration .1.3.6.1.4.1.17713.7.6.72 |
nIDULanPortGigabitMasterSlaveStatusThe NIDU LAN port Gigabit Ethernet Master/Slave statusro Enumeration .1.3.6.1.4.1.17713.7.6.73 |
txMABFramesNumber of MAB frames transmittedro Integer32 .1.3.6.1.4.1.17713.7.6.74 |
managementNetworkAccessEnabledWhen enabled the local Out-of-Band interface can be used to access the remote management network. If not enabled the local management agent can still be accessed from the remote management network and the local Out-of-Band interfacerw Enumeration .1.3.6.1.4.1.17713.7.6.75 |
secondDataPortPauseFramesControls whether the bridge tunnels or discards Layer 2 PAUSE frames arriving at the Second Data Service Port. Such frames are identified by the destination MAC Address being equal to 01-80-C2-00-00-01ro Enumeration .1.3.6.1.4.1.17713.7.6.76 |
secondDataBridgingStatusCurrent status of bridging Second Data Service Ethernet traffic over the wireless linkro Enumeration .1.3.6.1.4.1.17713.7.6.80 |
transparentClockPortIEEE 1588 Transparent Clock sourcerw Enumeration .1.3.6.1.4.1.17713.7.6.81 |
tDM OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.7 |
tDMInterfaceControlThe line interface type. If this is set to 'None' then the TDM interfaces are disabled, and the TDM settings will be ignored.ro Enumeration .1.3.6.1.4.1.17713.7.7.1 |
tDMInterfaceStatus@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be usedro Enumeration .1.3.6.1.4.1.17713.7.7.2 |
tDMEnabledChannelsThe number of TDM channels enabled in the systemro INTEGER .1.3.6.1.4.1.17713.7.7.3 |
tdmTableNumberNumber of entries in the TdmTablero INTEGER .1.3.6.1.4.1.17713.7.7.4 |
tdmTableA table storing a configuration and status for each TDM channel SEQUENCE OF TdmTableEntry .1.3.6.1.4.1.17713.7.7.5 |
tdmTableEntryTable TdmTable TdmTableEntry .1.3.6.1.4.1.17713.7.7.5.1 |
tdmTableIndexTDM Channel flag, used to index channels in the TdmTable INTEGER .1.3.6.1.4.1.17713.7.7.5.1.1 |
tDMChannelStatusCurrent status of the TDM channels. A value of 0 indicates that a TDM channel is establishedro Enumeration .1.3.6.1.4.1.17713.7.7.5.1.2 |
tDMChannelLineCodeThe line code setting of the TDM interfaces. This must match the setting of the device connected to an interfacero Enumeration .1.3.6.1.4.1.17713.7.7.5.1.3 |
tDMChannelCableLengthThe lengths of the cables connected to the TDM interfaces, measured in feetro Enumeration .1.3.6.1.4.1.17713.7.7.5.1.4 |
tDMChannelLoopbackThe loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.7.5.1.5 |
tDMConfigurationMismatchCurrent status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end.ro Enumeration .1.3.6.1.4.1.17713.7.7.6 |
lowestTDMModulationModeThe lowest modulation mode at which tdm data will be sent. The effective lowest modulation mode is displayed in the TDM Configuration pagero Enumeration .1.3.6.1.4.1.17713.7.7.7 |
license OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.8 |
regulatoryBandThe Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key. NB: a change of state may generate an SNMP trap and/or SMTP email alert.ro Enumeration .1.3.6.1.4.1.17713.7.8.1 |
productVariantThe product variantro Enumeration .1.3.6.1.4.1.17713.7.8.2 |
productNameName of the product variantro DisplayString .1.3.6.1.4.1.17713.7.8.3 |
frequencyVariantThe hardware frequency variantro Enumeration .1.3.6.1.4.1.17713.7.8.5 |
sNMPv3EnableSNMPv3 availability controlro Enumeration .1.3.6.1.4.1.17713.7.8.9 |
licenseVersionThe license key version.ro INTEGER (1) .1.3.6.1.4.1.17713.7.8.12 |
licenseUnitSerialNumberThe unit serial number.ro DisplayString .1.3.6.1.4.1.17713.7.8.13 |
licenseIssueNumberThe license key issue number for this unit.ro INTEGER .1.3.6.1.4.1.17713.7.8.15 |
licenseCountryThe country in which this unit is licensed to operate.ro DisplayString .1.3.6.1.4.1.17713.7.8.16 |
licenseNumberOfRegulatoryBandsThe number of regulatory bands for which the unit is licensed to operate.ro INTEGER .1.3.6.1.4.1.17713.7.8.17 |
licenseRegulatoryBandsTable SEQUENCE OF LicenseRegulatoryBandsTableEntry .1.3.6.1.4.1.17713.7.8.18 |
licenseRegulatoryBandsTableEntryTable LicenseRegulatoryBandsTable LicenseRegulatoryBandsTableEntry .1.3.6.1.4.1.17713.7.8.18.1 |
licenseRegulatoryBandsTableIndexLicense regulatory bands, used to index the LicenseRegulatoryBandsTable. INTEGER .1.3.6.1.4.1.17713.7.8.18.1.1 |
licenseRegulatoryBandsListThe list of regulatory bands for which the unit is licensed to operate. A regulatory band prohibits the wireless unit from operating outside the regulated limits. An invalid regulatory band indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert.ro Enumeration .1.3.6.1.4.1.17713.7.8.18.1.2 |
licenseBandwidthCapThe wireless link bandwidth cap in MHz. Zero indicates no bandwidth cap.ro INTEGER .1.3.6.1.4.1.17713.7.8.20 |
licenseEncryptionThe license key encryption algorithms available.ro Enumeration .1.3.6.1.4.1.17713.7.8.21 |
licenseSecurityLevelThe license key security level.ro Enumeration .1.3.6.1.4.1.17713.7.8.22 |
licenseGroupAccessThe license key group access setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.23 |
licenseOOBManagementSupportThe license key Out-Of-Band (OOB) support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.24 |
licenseSFPPortSupportThe license key Ethernet SFP Port support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.25 |
licenseAuxiliaryPortSupportThe license key Ethernet Auxiliary Port support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.26 |
licenseCapacityThe license key capacityro Enumeration .1.3.6.1.4.1.17713.7.8.27 |
licenseMaxNumberOfTDMChannelsThe license key maximum TDM channels setting. Zero indicates TDM not available.ro INTEGER .1.3.6.1.4.1.17713.7.8.28 |
licenseIEEE1588SupportThe license key IEEE-1588 support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.29 |
licenseSyncESupportThe license key SyncE support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.30 |
licenseIPv6SupportThe license key IPv6 support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.31 |
licenseMinimumFirmwareVersionThe minimum firmware version required to support this license key.ro DisplayString .1.3.6.1.4.1.17713.7.8.32 |
licenseFullCapabilityTrialStatusThe license key full capability trial period status.ro Enumeration .1.3.6.1.4.1.17713.7.8.33 |
licenseRemainingTrialPeriodThe remaining time for the license key full capability trial period.ro INTEGER .1.3.6.1.4.1.17713.7.8.34 |
licenseRemainingTrialPeriodAlarmIf the full capability trial license period is about to expire then purchase a license upgrade from your reseller.ro Enumeration .1.3.6.1.4.1.17713.7.8.35 |
capacityVariantMismatchThe remote node of this link has a lower link capacity. Operating with a reduced effective link capacity.ro Enumeration .1.3.6.1.4.1.17713.7.8.36 |
licenseTDDSyncSupportThe license key TDD Synchronization support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.37 |
licenseMaxLinkRangeMaximum licensed range for the wireless link in tenths of km. A value of zero indicates that the maximum link range is not limited by the license.ro INTEGER .1.3.6.1.4.1.17713.7.8.38 |
licenseTrialPeriodThe license key maximum trial period, in days.ro INTEGER .1.3.6.1.4.1.17713.7.8.39 |
licenseRARSupportThe license key Radio Aware Routing support setting.ro Enumeration .1.3.6.1.4.1.17713.7.8.40 |
management OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.9 |
targetRangeInitial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0ro INTEGER .1.3.6.1.4.1.17713.7.9.1 |
rangingModeType of ranging to use during installation, either Auto-Ranging or use a selectable Target Rangero Enumeration .1.3.6.1.4.1.17713.7.9.2 |
installStatusA non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.9.3 |
installArmStateIndicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.9.4 |
tFTPServerPortNumberThe port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedrw INTEGER .1.3.6.1.4.1.17713.7.9.6 |
tFTPSoftwareUpgradeFileNameFilename of the Software Upgrade to be loaded from the TFTP Serverrw DisplayString .1.3.6.1.4.1.17713.7.9.7 |
tFTPStartSoftwareUpgradeWrite '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with the software upgrade will cause spectrum management (DSO) channel metrics collection to stop. The wireless unit will no longer search for the optimal operational radio channel. The performance of this wireless link may deterioate over time. If operating in a regulatory band where RADAR detection is mandatory you must complete the software upgrade and reboot the unit. Channel metrics collection will only be restarted after the wireless unit has been rebootedrw Integer32 .1.3.6.1.4.1.17713.7.9.8 |
tFTPSoftwareUpgradeStatusThe current status of the TFTP Software upgrade processro Enumeration .1.3.6.1.4.1.17713.7.9.9 |
tFTPSoftwareUpgradeStatusTextDescriptive text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.7.9.10 |
tFTPSoftwareUpgradeStatusAdditionalTextAny additional text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.7.9.11 |
hTTPAccessEnabledThis controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)rw Enumeration .1.3.6.1.4.1.17713.7.9.12 |
telnetAccessEnabledThis controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)rw Enumeration .1.3.6.1.4.1.17713.7.9.13 |
hTTPPortNumberThis controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)rw INTEGER .1.3.6.1.4.1.17713.7.9.14 |
hTTPSPortNumberThis controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)rw INTEGER .1.3.6.1.4.1.17713.7.9.15 |
telnetPortNumberThis controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)rw INTEGER .1.3.6.1.4.1.17713.7.9.16 |
hTTPSAccessEnabledThis controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)rw Enumeration .1.3.6.1.4.1.17713.7.9.17 |
tFTPServerInternetAddressTypeThe type of Internet address specified by the associated tFTPServerInternetAddress.ro Enumeration .1.3.6.1.4.1.17713.7.9.18 |
tFTPServerInternetAddressINET address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedrw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.17713.7.9.19 |
lowestDataModulationModeThe lowest modulation mode at which Ethernet Data traffic will be bridged over the wireless linkro Enumeration .1.3.6.1.4.1.17713.7.9.20 |
lowestSecondDataModulationModeThe lowest modulation mode at which Second Data Service Ethernet traffic will be bridged over the wireless linkro Enumeration .1.3.6.1.4.1.17713.7.9.21 |
phyControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.10 |
linkSymmetryProvides configuration options for sharing the available wireless capacity between the transmit and receive directions. Fixed link symmetry is defined by a ratio of the burst duration for the transmit direction to the burst duration for the receive direction. Permitted settings are 5:1, 3:1, 2:1, 1:1, 1:2, 1:3, 1:5. The 1:1 option provides fixed symmetric operation. The adaptive option selects transmit and receive burst durations automatically in response to the offered Ethernet traffic in each link direction. This attribute is valid only for a unit configured as a TDD Masterro Enumeration .1.3.6.1.4.1.17713.7.10.1 |
userConfiguredMaxModulationModeThe maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizardrw Enumeration .1.3.6.1.4.1.17713.7.10.2 |
linkModeOptimizationOptimizes the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimize transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimize transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols.ro Enumeration .1.3.6.1.4.1.17713.7.10.3 |
txColorCodeTransmit Color Code. This attribute need only be considered when the unit is installed in a network of PTP units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Rx Color Code parameter at the far end of the link.ro Enumeration .1.3.6.1.4.1.17713.7.10.4 |
rxColorCodeReceive Color Code. This attribute need only be considered when the unit is installed in a network of PTP units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Tx Color Code parameter at the far end of the link.ro Enumeration .1.3.6.1.4.1.17713.7.10.5 |
remoteMaximumTransmitPowerMaximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless linkro INTEGER (-15..30) .1.3.6.1.4.1.17713.7.10.6 |
phyStatus OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.12 |
linkLossThe wireless link loss expressed in tenths of a dBro INTEGER (-500..500) .1.3.6.1.4.1.17713.7.12.1 |
receivePowerReceive power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.7.12.2 |
vectorErrorThe vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.7.12.3 |
transmitPowerTransmit power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.7.12.4 |
receiveChannelCurrent active receive channelro INTEGER .1.3.6.1.4.1.17713.7.12.5 |
transmitChannelCurrent active transmit channelro INTEGER .1.3.6.1.4.1.17713.7.12.6 |
receiveFreqMHzCurrent receive frequency expressed in integer MHzro INTEGER .1.3.6.1.4.1.17713.7.12.7 |
transmitFreqMHzCurrent transmit frequency expressed in integer MHzro INTEGER .1.3.6.1.4.1.17713.7.12.8 |
signalStrengthRatioSignal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.7.12.9 |
receiveFreqKHzCurrent receive frequency expressed as KHzro INTEGER .1.3.6.1.4.1.17713.7.12.10 |
transmitFreqKHzCurrent transmit frequency expressed as KHzro INTEGER .1.3.6.1.4.1.17713.7.12.11 |
rawReceivePowerRaw receive power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.7.12.12 |
rangeDistance between the two peer wireless units expressed in tenths of a kilometerro Integer32 .1.3.6.1.4.1.17713.7.12.13 |
receiveModulationModeCurrent active receive modulation modero Enumeration .1.3.6.1.4.1.17713.7.12.14 |
transmitModulationModeCurrent active transmit modulation modero Enumeration .1.3.6.1.4.1.17713.7.12.15 |
searchStateSearch status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.ro Enumeration .1.3.6.1.4.1.17713.7.12.16 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.13 |
unitOutOfCalibrationThe unit is out of calibrationro Enumeration .1.3.6.1.4.1.17713.7.13.1 |
incompatibleRegulatoryBandsThe master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keysro Enumeration .1.3.6.1.4.1.17713.7.13.4 |
noWirelessChannelAvailableSpectrum Management was unable to locate a suitable wireless channel to operate onro Enumeration .1.3.6.1.4.1.17713.7.13.5 |
wirelessLinkDisabledWarningThe SNMP ifAdminStatus of the wireless interface has disabled wireless trafficro Enumeration .1.3.6.1.4.1.17713.7.13.6 |
mainPSUPortDisabledWarningThe SNMP ifAdminStatus of the interface has disabled Ethernet trafficro Enumeration .1.3.6.1.4.1.17713.7.13.7 |
sFPErrorIf the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.13.8 |
mainPSUPortConfigurationMismatchThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatchro Enumeration .1.3.6.1.4.1.17713.7.13.9 |
incompatibleMasterAndSlaveA non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.7.13.10 |
tDDSynchronizationStatusAn alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference.ro Enumeration .1.3.6.1.4.1.17713.7.13.11 |
auxPortDisabledWarningThe SNMP ifAdminStatus of the interface has disabled Ethernet trafficro Enumeration .1.3.6.1.4.1.17713.7.13.12 |
tDDSynchronizationAlarmNot Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.ro Enumeration .1.3.6.1.4.1.17713.7.13.13 |
linkModeOptimizationMismatchThe remote node of this link has been configured with a different link mode optimizationro Enumeration .1.3.6.1.4.1.17713.7.13.14 |
auxPortConfigurationMismatchThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.ro Enumeration .1.3.6.1.4.1.17713.7.13.15 |
secureModeAlarmThe secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image.ro Enumeration .1.3.6.1.4.1.17713.7.13.16 |
dataBridgingStatusAlarmEthernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Modero Enumeration .1.3.6.1.4.1.17713.7.13.17 |
sFPPortDisabledWarningThe SNMP ifAdminStatus of the interface has disabled Ethernet trafficro Enumeration .1.3.6.1.4.1.17713.7.13.18 |
sFPPortConfigurationMismatchThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.ro Enumeration .1.3.6.1.4.1.17713.7.13.19 |
maxLinkRangeExceededThe measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active.ro Enumeration .1.3.6.1.4.1.17713.7.13.20 |
nIDULanPortDisabledWarningThe SNMP ifAdminStatus of the interface has disabled Ethernet trafficro Enumeration .1.3.6.1.4.1.17713.7.13.21 |
nIDULanPortConfigurationMismatchThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch.ro Enumeration .1.3.6.1.4.1.17713.7.13.22 |
portAllocationMismatchThe local and remote ODUs have different services configured.ro Enumeration .1.3.6.1.4.1.17713.7.13.23 |
secondDataBridgingStatusAlarmBridging of Ethernet traffic from Second Data Service has been disabled because the wireless link is not operating at the configured Lowest Second Data Modulation Modero Enumeration .1.3.6.1.4.1.17713.7.13.24 |
transparentClockSourcePortAlarmTransparent Clock will not function properly because SFP, the selected clock source port is not FIBERro Enumeration .1.3.6.1.4.1.17713.7.13.25 |
smtp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.15 |
sMTPEmailAlertSimple Mail Transfer Protocol is used to send equipment alerts via email to a specified email addressrw Enumeration .1.3.6.1.4.1.17713.7.15.1 |
sMTPServerPortNumberPort number of the SMTP serverrw INTEGER .1.3.6.1.4.1.17713.7.15.3 |
sMTPSourceEmailAddressThe 'from' email address used when constructing the automatically generated e-mail messagerw DisplayString .1.3.6.1.4.1.17713.7.15.4 |
sMTPDestinationEmailAddressThe 'to' email address used when constructing the automatically generated e-mail messagerw DisplayString .1.3.6.1.4.1.17713.7.15.5 |
sMTPEnabledMessagesThis controls which SMTP messages the unit will sendrw Bits .1.3.6.1.4.1.17713.7.15.6 |
sMTPServerInternetAddressTypeThe type of Internet address specified by the associated sMTPServerInternetAddress.ro Enumeration .1.3.6.1.4.1.17713.7.15.7 |
sMTPServerInternetAddressInternet address of the SMTP serverrw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.17713.7.15.8 |
snmpControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.16 |
sNMPPortNumberThe IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attributerw INTEGER .1.3.6.1.4.1.17713.7.16.1 |
sNMPCommunityStringThe SNMP community string. NB: A system reboot is required to activate changes to this attributerw DisplayString .1.3.6.1.4.1.17713.7.16.2 |
sNMPTrapTableNumberNumber of entries in the sNMPTrapTable.ro INTEGER (2) .1.3.6.1.4.1.17713.7.16.3 |
sNMPTrapTableSNMP trap configuration table. SEQUENCE OF SNMPTrapTableEntry .1.3.6.1.4.1.17713.7.16.4 |
sNMPTrapTableEntryTable SNMPTrapTable SNMPTrapTableEntry .1.3.6.1.4.1.17713.7.16.4.1 |
sNMPTrapTableIndexSNMP trap value, used to index the SNMPTrapTable. INTEGER .1.3.6.1.4.1.17713.7.16.4.1.1 |
sNMPTrapPortNumberDestination port for SNMP Traps (default=162). NB: A system reboot is required to activate changes to this attribute.rw INTEGER .1.3.6.1.4.1.17713.7.16.4.1.3 |
sNMPTrapInternetAddressTypeThe type of Internet address specified by the associated sNMPTrapInternetAddress.ro Enumeration .1.3.6.1.4.1.17713.7.16.4.1.4 |
sNMPTrapInternetAddressThe Internet address to which all SNMP Traps are sent.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.17713.7.16.4.1.5 |
sNMPTrapReceiverEnabledA value of 0 disables the sending of SNMP trap to corresponding receiver. A value of 1 enables the sending of SNMP trap to corresponding receiver.rw Enumeration .1.3.6.1.4.1.17713.7.16.4.1.6 |
sNMPTrapVersionThe SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attributerw Enumeration .1.3.6.1.4.1.17713.7.16.5 |
sNMPEnabledTrapsThis controls which SNMP Traps the unit will sendrw Bits .1.3.6.1.4.1.17713.7.16.6 |
enabledDiagnosticAlarmsControls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributesrw Bits .1.3.6.1.4.1.17713.7.16.7 |
sNMPSendAllTrapsAtStartupControls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up.rw Enumeration .1.3.6.1.4.1.17713.7.16.8 |
sntp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.17 |
sNTPStateSNTP control staterw Enumeration .1.3.6.1.4.1.17713.7.17.1 |
sNTPPollIntervalThe SNTP server polling intervalrw INTEGER .1.3.6.1.4.1.17713.7.17.4 |
sNTPSyncIf SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTPro Enumeration .1.3.6.1.4.1.17713.7.17.5 |
sNTPLastSyncLast SNTP sync timero Integer32 .1.3.6.1.4.1.17713.7.17.6 |
systemClockSystem clock presented as local timero Integer32 .1.3.6.1.4.1.17713.7.17.7 |
timeZoneTime zone offsets from Greenwich Mean Time (GMT)rw Enumeration .1.3.6.1.4.1.17713.7.17.8 |
daylightSavingDaylight Saving Timerw Enumeration .1.3.6.1.4.1.17713.7.17.9 |
sNTPPrimaryServerSpecifies the primary SNTP server, determining the order in which the servers are tried.rw Enumeration .1.3.6.1.4.1.17713.7.17.10 |
sNTPPrimaryServerDeadTimeTime (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer.rw INTEGER .1.3.6.1.4.1.17713.7.17.11 |
sNTPServerRetriesNumber of times the PTP will retry after an SNTP server fails to respond.rw INTEGER .1.3.6.1.4.1.17713.7.17.12 |
sNTPServerTimeoutTime (in seconds) the PTP will wait for a response from an SNTP server.rw INTEGER .1.3.6.1.4.1.17713.7.17.13 |
sNTPServerTableNumberNumber of entries in the SNTPServerTable.ro INTEGER (2) .1.3.6.1.4.1.17713.7.17.14 |
sNTPServerTable SEQUENCE OF SNTPServerTableEntry .1.3.6.1.4.1.17713.7.17.15 |
sNTPServerTableEntryTable SNTPServerTable SNTPServerTableEntry .1.3.6.1.4.1.17713.7.17.15.1 |
sNTPServerTableIndexIndex range for the SNTPServerTable. INTEGER .1.3.6.1.4.1.17713.7.17.15.1.1 |
sNTPServerPortNumberThe IP port number of the SNTP server. Defaults to port 123.rw INTEGER .1.3.6.1.4.1.17713.7.17.15.1.3 |
sNTPServerStatusStatus message reflecting the result of communications with the SNTP server when last polledro DisplayString .1.3.6.1.4.1.17713.7.17.15.1.4 |
sNTPServerInternetAddressTypeThe type of Internet address specified by the associated sNTPServerInternetAddress.ro Enumeration .1.3.6.1.4.1.17713.7.17.15.1.5 |
sNTPServerInternetAddressThe Internet address of a valid SNTP serverrw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.17713.7.17.15.1.6 |
reset OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.18 |
systemResetSetting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memoryrw Enumeration .1.3.6.1.4.1.17713.7.18.1 |
versions OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.19 |
softwareVersionCurrent software versionro DisplayString .1.3.6.1.4.1.17713.7.19.1 |
hardwareVersionHardware platform versionro DisplayString .1.3.6.1.4.1.17713.7.19.2 |
secondarySoftwareVersionSecondary software version, used when the primary software image is invalid or erasedro DisplayString .1.3.6.1.4.1.17713.7.19.3 |
bootVersionBoot code software versionro DisplayString .1.3.6.1.4.1.17713.7.19.4 |
pubStats OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.20 |
receiveDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.7.20.1 |
transmitDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.7.20.2 |
aggregateDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.7.20.3 |
wirelessLinkAvailabilityLink availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precisionro INTEGER .1.3.6.1.4.1.17713.7.20.4 |
wirelessLinkStatusCurrent status of the wireless linkro Enumeration .1.3.6.1.4.1.17713.7.20.5 |
byteErrorRatioReciprocal of the byte error ratio calculated since the last reset of the system countersro Integer32 .1.3.6.1.4.1.17713.7.20.6 |
receiveModulationModeDetailThe reason for the current receive modulation modero Enumeration .1.3.6.1.4.1.17713.7.20.7 |
dataBridgingAvailabilityLink availability bridging Ethernet Data traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precisionro INTEGER .1.3.6.1.4.1.17713.7.20.8 |
encryption OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.22 |
encryptionAlgorithmThe Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctlyro Enumeration .1.3.6.1.4.1.17713.7.22.1 |
tDDControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.23 |
tDDSynchronizationModeTDD Synchronization Mode selectionro Enumeration .1.3.6.1.4.1.17713.7.23.1 |
syslogControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.24 |
syslogClientEnable or disable the syslog clientro Enumeration .1.3.6.1.4.1.17713.7.24.1 |
syslogStateThe syslog service has been enabled or disabledro Enumeration .1.3.6.1.4.1.17713.7.24.2 |
aAAControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.25 |
userTableNumberNumber of entries in the userTablero INTEGER .1.3.6.1.4.1.17713.7.25.1 |
userTableThe User Table Control group contains objects specifically for user account management. SEQUENCE OF UserTableEntry .1.3.6.1.4.1.17713.7.25.2 |
userTableEntryTable UserTable UserTableEntry .1.3.6.1.4.1.17713.7.25.2.1 |
userTableIndexused to index values in the userTable. INTEGER .1.3.6.1.4.1.17713.7.25.2.1.1 |
userNameUser name which must be entered, along with the appropriate password, in order to gain access to the system.ro DisplayString .1.3.6.1.4.1.17713.7.25.2.1.2 |
userRoleRole of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes.ro Enumeration .1.3.6.1.4.1.17713.7.25.2.1.3 |
userEnabledEnable / Disable the selected userro Enumeration .1.3.6.1.4.1.17713.7.25.2.1.4 |
userPasswordUser password, which must be entered in order to gain access to the system.rw DisplayString .1.3.6.1.4.1.17713.7.25.2.1.5 |
routerProtocols OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.26 |
microwaveAdaptiveBandwidthEnable support of Microwave Adaptive Bandwidth Protocol. MAB is disabled if link symmetry is configured as Adaptivero Enumeration .1.3.6.1.4.1.17713.7.26.1 |
mABNominalModulationModeThe Nominal modulation mode is the desired modulation mode. MAB VSM packets are generated when the current modulation mode falls below the nominal modulation.ro Enumeration .1.3.6.1.4.1.17713.7.26.2 |
mABTransmissionIntervalThe minimum interval (in seconds) between successive MAB vendor specific messages (VSM). These VSM are sent when the current transmit capacity falls below the configured MAB Nominal Modulation Mode.ro Enumeration .1.3.6.1.4.1.17713.7.26.3 |
mABHoldoffPeriodThe period (in seconds) over which transmit capacity is averaged over to determine when the wireless link has degradedro INTEGER .1.3.6.1.4.1.17713.7.26.4 |
mABMaintenanceLevelMaintenance Levels (0-7) determines the destination MAC address of MAB vendor specific messages.ro INTEGER .1.3.6.1.4.1.17713.7.26.5 |
useVLANForMABProtocolThis controls whether MAB vendor specific messages (VSM) packets use VLAN tags or not.ro Enumeration .1.3.6.1.4.1.17713.7.26.6 |
mABProtocolVIDThis VLAN VID (0-4094) will be included in MAB vendor specific messages (VSM) packets.ro INTEGER .1.3.6.1.4.1.17713.7.26.7 |
mABProtocolVLANPriorityThis VLAN Priority (0-7) will be included in MAB vendor specific messages (VSM) packets.ro INTEGER .1.3.6.1.4.1.17713.7.26.8 |
mABStateCurrent state of MAB Protocol. A state of 'Normal' on a green background indicates that a PTP link is operating at nominal capacityro Enumeration .1.3.6.1.4.1.17713.7.26.9 |
mABNominalTransmitCapacityThe nominal Tx capacity used in MAB Vendor Specific Messages for the selected nominal modulation modero INTEGER .1.3.6.1.4.1.17713.7.26.10 |
mABCurrentTransmitCapacityThe current Tx capacity of the wireless link used in the last MAB Vendor Specific Message transmitted.ro INTEGER .1.3.6.1.4.1.17713.7.26.11 |
cableDiagnostics OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.27 |
cableDiagnosticsPortsSelect ports on which Cable Diagnostics must be executedrw Bits .1.3.6.1.4.1.17713.7.27.1 |
cableDiagnosticsControlSet this attribute to 'Test in Progress' to start a Cable Diagnostics testrw Enumeration .1.3.6.1.4.1.17713.7.27.2 |
cableDiagnosticsWarningNormal Ethernet operation is disrupted when a Cable Diagnostics test is in progressro Enumeration .1.3.6.1.4.1.17713.7.27.3 |
cableDiagnosticsResultTableNumberNumber of rows in the Cable Diagnostics Result Table.ro INTEGER .1.3.6.1.4.1.17713.7.27.4 |
cableDiagnosticsResultTable SEQUENCE OF CableDiagnosticsResultTableEntry .1.3.6.1.4.1.17713.7.27.5 |
cableDiagnosticsResultTableEntryTable CableDiagnosticsResultTable CableDiagnosticsResultTableEntry .1.3.6.1.4.1.17713.7.27.5.1 |
cableDiagnosticsResultTableIndexCable Diagnostics Port value used to index into the result table. INTEGER .1.3.6.1.4.1.17713.7.27.5.1.1 |
cableDiagnosticsResultsDateTimeThe Date and Time when a Cable Diagnostics test was last executedro Integer32 .1.3.6.1.4.1.17713.7.27.5.1.2 |
cableDiagPair1ResultsThe result of the most recent execution of Cable Diagnostics on cable pair 1. According to the T658B wiring scheme, pair 1 is pins 4 & 5 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.ro Enumeration .1.3.6.1.4.1.17713.7.27.5.1.3 |
cableDiagPair1DistanceThe distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).ro Integer32 .1.3.6.1.4.1.17713.7.27.5.1.4 |
cableDiagPair2ResultsThe result of the most recent execution of Cable Diagnostics on cable pair 2. According to the T658B wiring scheme, pair 2 is pins 1 & 2 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.ro Enumeration .1.3.6.1.4.1.17713.7.27.5.1.5 |
cableDiagPair2DistanceThe distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).ro Integer32 .1.3.6.1.4.1.17713.7.27.5.1.6 |
cableDiagPair3ResultsThe result of the most recent execution of Cable Diagnostics on cable pair 3. According to the T658B wiring scheme, pair 3 is pins 3 & 6 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.ro Enumeration .1.3.6.1.4.1.17713.7.27.5.1.7 |
cableDiagPair3DistanceThe distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).ro Integer32 .1.3.6.1.4.1.17713.7.27.5.1.8 |
cableDiagPair4ResultsThe result of the most recent execution of Cable Diagnostics on cable pair 4. According to the T658B wiring scheme, pair 4 is pins 7 & 8 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test.ro Enumeration .1.3.6.1.4.1.17713.7.27.5.1.9 |
cableDiagPair4DistanceThe distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).ro Integer32 .1.3.6.1.4.1.17713.7.27.5.1.10 |
supplementary OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.96 |
longitudeThe longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.rw DisplayString .1.3.6.1.4.1.17713.7.96.1 |
latitudeThe latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.rw DisplayString .1.3.6.1.4.1.17713.7.96.2 |
altitudeThe altitude of the unit, measured in meters. This object is set by the SNMP manager and has no internal function.rw Integer32 .1.3.6.1.4.1.17713.7.96.3 |
ptpComplianceThe compliance statement for the Cambium PTP MIB Unknown .1.3.6.1.4.1.17713.7.97 |
ptpGroups OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.98 |
dfsGroupThe dfs object group. Unknown .1.3.6.1.4.1.17713.7.98.3 |
bridgeGroupThe bridge object group. Unknown .1.3.6.1.4.1.17713.7.98.4 |
configurationGroupThe configuration object group. Unknown .1.3.6.1.4.1.17713.7.98.5 |
ethernetGroupThe ethernet object group. Unknown .1.3.6.1.4.1.17713.7.98.6 |
tDMGroupThe tDM object group. Unknown .1.3.6.1.4.1.17713.7.98.7 |
licenseGroupThe license object group. Unknown .1.3.6.1.4.1.17713.7.98.8 |
managementGroupThe management object group. Unknown .1.3.6.1.4.1.17713.7.98.9 |
phyControlGroupThe phyControl object group. Unknown .1.3.6.1.4.1.17713.7.98.10 |
phyStatusGroupThe phyStatus object group. Unknown .1.3.6.1.4.1.17713.7.98.12 |
alarmsGroupThe alarms object group. Unknown .1.3.6.1.4.1.17713.7.98.13 |
smtpGroupThe smtp object group. Unknown .1.3.6.1.4.1.17713.7.98.15 |
snmpControlGroupThe snmpControl object group. Unknown .1.3.6.1.4.1.17713.7.98.16 |
sntpGroupThe sntp object group. Unknown .1.3.6.1.4.1.17713.7.98.17 |
resetGroupThe reset object group. Unknown .1.3.6.1.4.1.17713.7.98.18 |
versionsGroupThe versions object group. Unknown .1.3.6.1.4.1.17713.7.98.19 |
pubStatsGroupThe pubStats object group. Unknown .1.3.6.1.4.1.17713.7.98.20 |
encryptionGroupThe encryption object group. Unknown .1.3.6.1.4.1.17713.7.98.22 |
tDDControlGroupThe tDDControl object group. Unknown .1.3.6.1.4.1.17713.7.98.23 |
syslogControlGroupThe syslogControl object group. Unknown .1.3.6.1.4.1.17713.7.98.24 |
aAAControlGroupThe aAAControl object group. Unknown .1.3.6.1.4.1.17713.7.98.25 |
routerProtocolsGroupThe routerProtocols object group. Unknown .1.3.6.1.4.1.17713.7.98.26 |
cableDiagnosticsGroupThe cableDiagnostics object group. Unknown .1.3.6.1.4.1.17713.7.98.27 |
supplementaryGroupThe supplementary object group. Unknown .1.3.6.1.4.1.17713.7.98.96 |
notificationsGroupThe notifications group. Unknown .1.3.6.1.4.1.17713.7.98.99 |
ptpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.99 |
ptpTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.17713.7.99.0 |
channelChangeTrapThe PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.1 |
dfsImpulsiveInterferenceTrapDFS impulsive interference detected event NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.2 |
mainPSUPortStatusTrapCurrent status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.3 |
mainPSUPortDisabledWarningTrapThe SNMP ifAdminStatus of the interface has disabled Ethernet traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.4 |
mainPSUPortConfigurationMismatchTrapThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.5 |
auxPortStatusTrapCurrent status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.6 |
auxPortDisabledWarningTrapThe SNMP ifAdminStatus of the interface has disabled Ethernet traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.7 |
regulatoryBandTrapThe Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key. NB: a change of state may generate an SNMP trap and/or SMTP email alert. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.8 |
installStatusTrapA non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.9 |
installArmStateTrapIndicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.10 |
unitOutOfCalibrationTrapThe unit is out of calibration NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.11 |
auxPortPowerOverEthernetOutputStatusTrapCurrent status of the Power Over Ethernet (PoE) output of the Aux port NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.12 |
incompatibleRegulatoryBandsTrapThe master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.14 |
noWirelessChannelAvailableTrapSpectrum Management was unable to locate a suitable wireless channel to operate on NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.15 |
wirelessLinkDisabledWarningTrapThe SNMP ifAdminStatus of the wireless interface has disabled wireless traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.16 |
auxPortConfigurationMismatchTrapThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.17 |
sFPErrorTrapIf the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.18 |
sFPPortStatusTrapCurrent status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.19 |
incompatibleMasterAndSlaveTrapA non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.20 |
sNTPSyncTrapIf SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.21 |
tDDSynchronizationAlarmTrapNot Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.22 |
sFPPortDisabledWarningTrapThe SNMP ifAdminStatus of the interface has disabled Ethernet traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.23 |
sFPPortConfigurationMismatchTrapThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.24 |
linkModeOptimizationMismatchTrapThe remote node of this link has been configured with a different link mode optimization NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.25 |
tDMInterfaceStatusTrap@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be used NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.26 |
tDMChannelStatusTrapCurrent status of the TDM channels. A value of 0 indicates that a TDM channel is established NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.27 |
tDMChannelLoopbackTrapThe loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.28 |
nIDULanPortStatusTrapCurrent status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.29 |
syslogStateTrapThe syslog service has been enabled or disabled NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.30 |
syslogLocalNearlyFullTrapThe syslog local log is nearly full (90%) NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.31 |
syslogLocalWrappedTrapThe syslog local log has wrapped NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.32 |
syslogClientTrapEnable or disable the syslog client NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.33 |
secureModeAlarmTrapThe secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.34 |
dataBridgingStatusAlarmTrapEthernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.35 |
licenseRemainingTrialPeriodAlarmTrapIf the full capability trial license period is about to expire then purchase a license upgrade from your reseller. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.36 |
capacityVariantMismatchTrapThe remote node of this link has a lower link capacity. Operating with a reduced effective link capacity. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.37 |
maxLinkRangeExceededTrapThe measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.38 |
tDMConfigurationMismatchTrapCurrent status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.39 |
nIDULanPortDisabledWarningTrapThe SNMP ifAdminStatus of the interface has disabled Ethernet traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.40 |
nIDULanPortConfigurationMismatchTrapThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.41 |
secondDataBridgingStatusAlarmTrapBridging of Ethernet traffic from Second Data Service has been disabled because the wireless link is not operating at the configured Lowest Second Data Modulation Mode NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.42 |
transparentClockSourcePortAlarmTrapTransparent Clock will not function properly because SFP, the selected clock source port is not FIBER NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.43 |
portAllocationMismatchTrapThe local and remote ODUs have different services configured. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.7.99.0.44 |