CAMBIUM-PTP600-MIB
AI MIB Summary
The CAMBIUM-PTP600-MIB enables SNMP-based monitoring and management of Cambium Networks PTP 600 series 300Mbps non-line-of-sight wireless Ethernet bridges, exposing critical operational metrics such as RF link quality, signal strength (RSSI), noise floor, throughput counters, and interface status.
MIB for 300Mbps non-line-of-sight (NLOS) wireless ethernet bridge.
Main OID:
cambium.1.3.6.1.4.1.17713
273
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
273 total| Object Name |
|---|
cambiumMIB for 300Mbps non-line-of-sight (NLOS) wireless ethernet bridge. MODULE-IDENTITY .1.3.6.1.4.1.17713 |
ptp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.1 |
ptmp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.2 |
ptp600 OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6 |
dfs OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.3 |
dfsTableNumberNumber of entries in the dfsTablero INTEGER .1.3.6.1.4.1.17713.6.3.1 |
dfsTableA table storing a snapshot of various DFS measurements for each channel SEQUENCE OF DfsTableEntry .1.3.6.1.4.1.17713.6.3.2 |
dfsTableEntryTable DfsTable DfsTableEntry .1.3.6.1.4.1.17713.6.3.2.1 |
dfsTableIndexused to index values in the dfsTable. INTEGER .1.3.6.1.4.1.17713.6.3.2.1.1 |
dfsMeansSnapshot of DFS meansro Integer32 .1.3.6.1.4.1.17713.6.3.2.1.2 |
dfsNineNinePointNinePercentilesSnapshot of DFS 99.9 percentilesro Integer32 .1.3.6.1.4.1.17713.6.3.2.1.3 |
dfsPeaksSnapshot of DFS peaksro Integer32 .1.3.6.1.4.1.17713.6.3.2.1.4 |
bridge OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.4 |
localPacketFilteringWhen Local Packet Filtering is Enabled, the bridge learns the source MAC addresses of devices transmitting Ethernet packets on the local Ethernet network, and only bridges packets to the remote unit if the destination MAC address has not been learnt as a 'local' device. When Local Packet Filtering is Disabled then the bridge does not learn the source MAC addresses of devices transmitting Ethernet packets on the local Ethernet network, and bridges ALL Ethernet packets received to the remote unit. Local Packet Filtering should be enabled if no external routing hardware is presentrw Enumeration .1.3.6.1.4.1.17713.6.4.1 |
configuration OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.5 |
iPAddressInternet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute.rw IpAddress .1.3.6.1.4.1.17713.6.5.1 |
subnetMaskA subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attributerw IpAddress .1.3.6.1.4.1.17713.6.5.2 |
gatewayIPAddressThe IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attributerw IpAddress .1.3.6.1.4.1.17713.6.5.3 |
targetMACAddressMAC address of the PTP wireless unit forming the other end of the PTP linkro OCTET STRING .1.3.6.1.4.1.17713.6.5.4 |
masterSlaveModeThe PTP wireless link operates using a master and slave relationshiprw Enumeration .1.3.6.1.4.1.17713.6.5.5 |
maximumTransmitPowerMaximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless linkro INTEGER (-15..27) .1.3.6.1.4.1.17713.6.5.6 |
antennaGainAntenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna.rw INTEGER .1.3.6.1.4.1.17713.6.5.7 |
cableLossLoss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.rw INTEGER .1.3.6.1.4.1.17713.6.5.8 |
eIRPEffective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBmro Integer32 .1.3.6.1.4.1.17713.6.5.9 |
ethernetCappedMaxWirelessSpeedEthernet frames will be discarded in the ODU if the data rate over the wireless link exceeds the Ethernet link speed at the local or remote Data port. The Ethernet Capped Max Wireless Speed control limits the wireless data rate based on the local and remote Ethernet link speed. Set this control to Enabled if either ODU is connected to an Ethernet link operating at less than 1000 Mbps. NB: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard.rw Enumeration .1.3.6.1.4.1.17713.6.5.10 |
channelBandwidthThis control sets the bandwidth of the transmit and receive radio channelsro Enumeration .1.3.6.1.4.1.17713.6.5.11 |
remoteIPAddressIP Address of the peer wireless unitro IpAddress .1.3.6.1.4.1.17713.6.5.12 |
linkNameName of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.rw DisplayString .1.3.6.1.4.1.17713.6.5.14 |
siteNameThis field contains a user-provided description of the site name together with any additional notesrw DisplayString .1.3.6.1.4.1.17713.6.5.15 |
accessMethodODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For the Link Access method, each ODU must be configured with Target MAC Address equal to the MAC Address of the other unit. For the Link Name Access method, both units must be configured with the same Link Name. For the Group Access method, both units must be configured with the same Group ID.ro Enumeration .1.3.6.1.4.1.17713.6.5.16 |
groupIDWhen Access Method is set to Group Access, the Group ID identifies all the units belonging to the same grouprw INTEGER .1.3.6.1.4.1.17713.6.5.17 |
ethernet OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.6 |
dataPortAutoNegotiationThis controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.rw Enumeration .1.3.6.1.4.1.17713.6.6.1 |
dataPortAutoNegAdvertisementThis sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!rw Bits .1.3.6.1.4.1.17713.6.6.2 |
dataPortAutoMdixThis enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system rebootrw Enumeration .1.3.6.1.4.1.17713.6.6.3 |
dataPortStatusCurrent status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.6.4 |
dataPortSpeedAndDuplexThe current speed and duplex of the Ethernet linkro Enumeration .1.3.6.1.4.1.17713.6.6.5 |
dataPortWirelessDownAlertWhen enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.rw Enumeration .1.3.6.1.4.1.17713.6.6.6 |
useVLANForManagementInterfacesThis controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system rebootrw Enumeration .1.3.6.1.4.1.17713.6.6.7 |
vLANManagementPriorityThis VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system rebootrw Enumeration .1.3.6.1.4.1.17713.6.6.8 |
vLANManagementVIDThis VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system rebootrw INTEGER .1.3.6.1.4.1.17713.6.6.11 |
managementPortStatusCurrent status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.6.12 |
managementPortSpeedAndDuplexThe current speed and duplex of the out-of-band management linkro Enumeration .1.3.6.1.4.1.17713.6.6.13 |
ethernetPriorityTableNumberNumber of entries in the vLANPriorityTable.ro INTEGER (9) .1.3.6.1.4.1.17713.6.6.14 |
ethernetPriorityTableA priority queue mapping table. This is a list of packet queues indexed by Ethernet priority. SEQUENCE OF EthernetPriorityTableEntry .1.3.6.1.4.1.17713.6.6.15 |
ethernetPriorityTableEntryTable EthernetPriorityTable EthernetPriorityTableEntry .1.3.6.1.4.1.17713.6.6.15.1 |
ethernetPriorityTableIndexEthernet priority flag, used to index values in the ethernetPriorityTable Enumeration .1.3.6.1.4.1.17713.6.6.15.1.1 |
ethernetPriorityQueueMappingConfigures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.6.6.15.1.2 |
l2CPPriorityTableNumberNumber of entries in the l2CPPriorityTable.ro INTEGER (5) .1.3.6.1.4.1.17713.6.6.16 |
l2CPPriorityTableA priority queue mapping table. This is a list of packet queues indexed by L2CP priority. SEQUENCE OF L2CPPriorityTableEntry .1.3.6.1.4.1.17713.6.6.17 |
l2CPPriorityTableEntryTable L2CPPriorityTable L2CPPriorityTableEntry .1.3.6.1.4.1.17713.6.6.17.1 |
l2CPPriorityTableIndexL2CP priority flag, used to index values in the l2CPPriorityTable Enumeration .1.3.6.1.4.1.17713.6.6.17.1.1 |
l2CPPriorityQueueMappingConfigures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.6.6.17.1.2 |
iPDSCPPriorityTableNumberNumber of entries in the iPDSCPPriorityTable.ro INTEGER (64) .1.3.6.1.4.1.17713.6.6.18 |
iPDSCPPriorityTableA priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority. SEQUENCE OF IPDSCPPriorityTableEntry .1.3.6.1.4.1.17713.6.6.19 |
iPDSCPPriorityTableEntryTable IPDSCPPriorityTable IPDSCPPriorityTableEntry .1.3.6.1.4.1.17713.6.6.19.1 |
iPDSCPPriorityTableIndexIP DSCP priority flag, used to index values in the iPDSCPPriorityTable INTEGER .1.3.6.1.4.1.17713.6.6.19.1.1 |
iPDSCPPriorityQueueMappingConfigures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.6.6.19.1.2 |
mPLSTCPriorityTableNumberNumber of entries in the mPLSTCPriorityTable.ro INTEGER (8) .1.3.6.1.4.1.17713.6.6.20 |
mPLSTCPriorityTableA priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority. SEQUENCE OF MPLSTCPriorityTableEntry .1.3.6.1.4.1.17713.6.6.21 |
mPLSTCPriorityTableEntryTable MPLSTCPriorityTable MPLSTCPriorityTableEntry .1.3.6.1.4.1.17713.6.6.21.1 |
mPLSTCPriorityTableIndexMPLS TC priority flag, used to index values in the mPLSTCPriorityTable INTEGER .1.3.6.1.4.1.17713.6.6.21.1.1 |
mPLSTCPriorityQueueMappingConfigures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless portrw Enumeration .1.3.6.1.4.1.17713.6.6.21.1.2 |
managementModeOut-of-Band Management (only available on certain hardware models): End-to-end out-of-band mode in which the management agent can be reached from the management port at the local ODU and (assuming that the wireless link is established) the management port at the remote ODU. Out-of-Band Local Management (only available on certain hardware models): Similar to the standard Out-of-Band mode, except that management frames are not forwarded over the wireless link. In-Band Management (default): The management agent can be reached from the data port at the local ODU and (assuming that the wireless link is established) the data port at the remote ODU. In this mode the management port is disabled. In-Band Local Management (only available when 'Use VLAN For Management Interfaces' configures a VLAN tag): Similar to the standard In-Band mode, except that management frames are not forwarded over the wireless link.ro Enumeration .1.3.6.1.4.1.17713.6.6.22 |
managementPortWirelessDownAlertWhen enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.ro Enumeration .1.3.6.1.4.1.17713.6.6.23 |
qOSPrioritySchemeSelects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP and MPLSrw Enumeration .1.3.6.1.4.1.17713.6.6.24 |
unknownNetworkPriorityQueueMappingConfigures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLSrw Enumeration .1.3.6.1.4.1.17713.6.6.25 |
dSCPManagementPriorityThis Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfacesro INTEGER .1.3.6.1.4.1.17713.6.6.26 |
ethernetBridgingStatusCurrent status of Ethernet packet bridging over the wireless linkro Enumeration .1.3.6.1.4.1.17713.6.6.27 |
telecom OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.7 |
telecomsInterfaceThe line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored.ro Enumeration .1.3.6.1.4.1.17713.6.7.1 |
telecomsChannelAStatusCurrent status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.7.2 |
telecomsChannelBStatusCurrent status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.7.3 |
channelALineCodeThe line code setting of the telecoms interface. This must match the setting of the device connected to this interfacero Enumeration .1.3.6.1.4.1.17713.6.7.4 |
channelBLineCodeThe line code setting of the telecoms interface. This must match the setting of the device connected to this interfacero Enumeration .1.3.6.1.4.1.17713.6.7.5 |
channelACableLengthThe length of the cable connected to the telecoms interface, measured in feetro Enumeration .1.3.6.1.4.1.17713.6.7.6 |
channelBCableLengthThe length of the cable connected to the telecoms interface, measured in feetro Enumeration .1.3.6.1.4.1.17713.6.7.7 |
channelALoopbackThe loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.7.8 |
channelBLoopbackThe loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.7.9 |
telecomsChannelSelectionIndicates which telecoms channels have been enabled. If only Channel A has been enabled, then the Channel B attributes will be ignored.ro Enumeration .1.3.6.1.4.1.17713.6.7.10 |
licence OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.8 |
regionCodeThe region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.8.1 |
productVariantThe product variantro Enumeration .1.3.6.1.4.1.17713.6.8.2 |
productNameName of the product variantro DisplayString .1.3.6.1.4.1.17713.6.8.3 |
ethernetFiberSupportEthernet fiber support availability on this wireless unitro Enumeration .1.3.6.1.4.1.17713.6.8.4 |
frequencyVariantFrequency variant of the wireless unitro Enumeration .1.3.6.1.4.1.17713.6.8.5 |
bandwidthVariantBandwidth variant of the wireless unitro Enumeration .1.3.6.1.4.1.17713.6.8.6 |
constantPowerSpectralDensityConstant power spectral density mode controlro Enumeration .1.3.6.1.4.1.17713.6.8.7 |
sNMPv3EnableSNMPv3 availability controlro Enumeration .1.3.6.1.4.1.17713.6.8.9 |
hAZLOCConfigurationThe HAZLOC/ATEX Configuration of this unit. The Gas Group is configured by the license key.ro Enumeration .1.3.6.1.4.1.17713.6.8.10 |
securityLevelThe maximum configurable security levelro Enumeration .1.3.6.1.4.1.17713.6.8.11 |
management OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.9 |
targetRangeInitial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0ro INTEGER .1.3.6.1.4.1.17713.6.9.1 |
rangingModeType of ranging to use during installation, either Auto-Ranging or use a selectable Target Rangero Enumeration .1.3.6.1.4.1.17713.6.9.2 |
installStatusA non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.9.3 |
installArmStateIndicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.9.4 |
tFTPServerIPAddressIP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedrw IpAddress .1.3.6.1.4.1.17713.6.9.5 |
tFTPServerPortNumberThe port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedrw INTEGER .1.3.6.1.4.1.17713.6.9.6 |
tFTPSoftwareUpgradeFileNameFilename of the Software Upgrade to be loaded from the TFTP Serverrw DisplayString .1.3.6.1.4.1.17713.6.9.7 |
tFTPStartSoftwareUpgradeWrite '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with the software upgrade will cause spectrum management (iDFS) channel metrics collection to stop. The wireless unit will no longer search for the optimal operational radio channel. The performance of this wireless link may deterioate over time. If operating in a region where RADAR detection is mandatory you must complete the software upgrade and reboot the unit. Channel metrics collection will only be restarted after the wireless unit has been rebootedrw Integer32 .1.3.6.1.4.1.17713.6.9.8 |
tFTPSoftwareUpgradeStatusThe current status of the TFTP Software upgrade processro Enumeration .1.3.6.1.4.1.17713.6.9.9 |
tFTPSoftwareUpgradeStatusTextDescriptive text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.6.9.10 |
tFTPSoftwareUpgradeStatusAdditionalTextAny additional text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.6.9.11 |
hTTPAccessEnabledThis controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)rw Enumeration .1.3.6.1.4.1.17713.6.9.12 |
telnetAccessEnabledThis controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)rw Enumeration .1.3.6.1.4.1.17713.6.9.13 |
hTTPPortNumberThis controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)rw INTEGER .1.3.6.1.4.1.17713.6.9.14 |
hTTPSPortNumberThis controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)rw INTEGER .1.3.6.1.4.1.17713.6.9.15 |
telnetPortNumberThis controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)rw INTEGER .1.3.6.1.4.1.17713.6.9.16 |
hTTPSAccessEnabledThis controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)rw Enumeration .1.3.6.1.4.1.17713.6.9.17 |
phyControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.10 |
linkSymmetryLink Symmetry: in fixed symmetric mode the master spends an equal amount of time transmitting and receiving; in fixed asymmetric modes the master transmit and receive times have a fixed ratio; in adaptive mode the transmit and receive periods adjust with applied load.ro Enumeration .1.3.6.1.4.1.17713.6.10.1 |
linkModeOptimisationOptimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols.ro Enumeration .1.3.6.1.4.1.17713.6.10.2 |
userConfiguredMaxModulationModeThe maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizardrw Enumeration .1.3.6.1.4.1.17713.6.10.3 |
remoteMaximumTransmitPowerMaximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless linkro INTEGER (-15..27) .1.3.6.1.4.1.17713.6.10.4 |
txColorCodeTransmit Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Rx Color Code parameter at the far end of the link.ro Enumeration .1.3.6.1.4.1.17713.6.10.5 |
rxColorCodeReceive Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Tx Color Code parameter at the far end of the link.ro Enumeration .1.3.6.1.4.1.17713.6.10.6 |
automaticTxPowerControlWhen enabled, the transmit power of the local end is automatically adjusted to maintain a configurable target receive signal level at the remote end of the link. When set to Enable with initial estimate, the Slave estimates the optional transmit power before it responds to the Master.ro Enumeration .1.3.6.1.4.1.17713.6.10.8 |
remoteRxTargetPowerThis is the target receive level for the end of the link which is remote from the end being configured. When Automatic Power Control is enabled, the transmit power of the local end is automatically adjusted in order to maintain the receive signal level at the remote end within a range centered on this valuero INTEGER (-600..-400) .1.3.6.1.4.1.17713.6.10.9 |
phyStatus OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.12 |
receivePowerReceive power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.6.12.1 |
vectorErrorThe vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.6.12.2 |
transmitPowerTransmit power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.6.12.3 |
rangeDistance between the two peer wireless units expressed in tenths of a kilometerro Integer32 .1.3.6.1.4.1.17713.6.12.4 |
linkLossThe wireless link loss expressed in tenths of a dBro INTEGER (-500..500) .1.3.6.1.4.1.17713.6.12.5 |
receiveChannelCurrent active receive channelro INTEGER .1.3.6.1.4.1.17713.6.12.6 |
transmitChannelCurrent active transmit channelro INTEGER .1.3.6.1.4.1.17713.6.12.7 |
receiveModulationModeCurrent active receive modulation modero Enumeration .1.3.6.1.4.1.17713.6.12.8 |
transmitModulationModeCurrent active transmit modulation modero Enumeration .1.3.6.1.4.1.17713.6.12.9 |
receiveFreqMHzCurrent receive frequency expressed in integer MHzro INTEGER .1.3.6.1.4.1.17713.6.12.11 |
transmitFreqMHzCurrent transmit frequency expressed in integer MHzro INTEGER .1.3.6.1.4.1.17713.6.12.12 |
signalStrengthRatioSignal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.6.12.13 |
receiveFreqKHzCurrent receive frequency expressed as KHzro INTEGER .1.3.6.1.4.1.17713.6.12.14 |
transmitFreqKHzCurrent transmit frequency expressed as KHzro INTEGER .1.3.6.1.4.1.17713.6.12.15 |
searchStateSearch status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.ro Enumeration .1.3.6.1.4.1.17713.6.12.16 |
rawReceivePowerRaw receive power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.6.12.17 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.13 |
unitOutOfCalibrationThe unit is out of calibrationro Enumeration .1.3.6.1.4.1.17713.6.13.1 |
encryptionEnabledMismatchEncryption has been enabled on one end of the wireless link but not the otherro Enumeration .1.3.6.1.4.1.17713.6.13.3 |
incompatibleRegionCodesThe master and slave units have incompatible region codes. NB: Both units must have compatible license keysro Enumeration .1.3.6.1.4.1.17713.6.13.4 |
noWirelessChannelAvailableSpectrum Management was unable to locate a suitable wireless channel to operate onro Enumeration .1.3.6.1.4.1.17713.6.13.5 |
wirelessLinkDisabledWarningThe SNMP ifAdminStatus of the wireless interface has disabled wireless trafficro Enumeration .1.3.6.1.4.1.17713.6.13.6 |
dataPortDisabledWarningThe SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet trafficro Enumeration .1.3.6.1.4.1.17713.6.13.7 |
dataPortFiberStatusIf the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include fiber support), the link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), or the link could not be established and LOS is detected (i.e. no optical carrier is detected). NB: a change of status may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.13.8 |
dataPortConfigurationMismatchThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatchro Enumeration .1.3.6.1.4.1.17713.6.13.9 |
incompatibleMasterAndSlaveA non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.6.13.10 |
tDDSynchronizationStatusAn alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference.ro Enumeration .1.3.6.1.4.1.17713.6.13.11 |
managementPortDisabledWarningThe SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet trafficro Enumeration .1.3.6.1.4.1.17713.6.13.12 |
tDDSynchronizationAlarmNot Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.ro Enumeration .1.3.6.1.4.1.17713.6.13.13 |
linkModeOptimizationMismatchThe remote node of this link has been configured with a different link mode optimizationro Enumeration .1.3.6.1.4.1.17713.6.13.14 |
managementPortConfigurationMismatchThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.ro Enumeration .1.3.6.1.4.1.17713.6.13.15 |
secureModeAlarmThe secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image.ro Enumeration .1.3.6.1.4.1.17713.6.13.16 |
ethernetBridgingStatusAlarmEthernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Modero Enumeration .1.3.6.1.4.1.17713.6.13.17 |
smtp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.15 |
sMTPEmailAlertSimple Mail Transfer Protocol is used to send equipment alerts via email to a specified email addressrw Enumeration .1.3.6.1.4.1.17713.6.15.1 |
sMTPServerIPAddressIP address of the SMTP serverrw IpAddress .1.3.6.1.4.1.17713.6.15.2 |
sMTPServerPortNumberPort number of the SMTP serverrw INTEGER .1.3.6.1.4.1.17713.6.15.3 |
sMTPSourceEmailAddressThe 'from' email address used when constructing the automatically generated e-mail messagerw DisplayString .1.3.6.1.4.1.17713.6.15.4 |
sMTPDestinationEmailAddressThe 'to' email address used when constructing the automatically generated e-mail messagerw DisplayString .1.3.6.1.4.1.17713.6.15.5 |
sMTPEnabledMessagesThis controls which SMTP messages the unit will sendrw Bits .1.3.6.1.4.1.17713.6.15.6 |
snmpControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.16 |
sNMPPortNumberThe IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attributerw INTEGER .1.3.6.1.4.1.17713.6.16.1 |
sNMPCommunityStringThe SNMP community string. NB: A system reboot is required to activate changes to this attributerw DisplayString .1.3.6.1.4.1.17713.6.16.2 |
sNMPTrapTableNumberNumber of entries in the sNMPTrapTable.ro INTEGER (2) .1.3.6.1.4.1.17713.6.16.3 |
sNMPTrapTableSNMP trap configuration table. SEQUENCE OF SNMPTrapTableEntry .1.3.6.1.4.1.17713.6.16.4 |
sNMPTrapTableEntryTable SNMPTrapTable SNMPTrapTableEntry .1.3.6.1.4.1.17713.6.16.4.1 |
sNMPTrapTableIndexSNMP trap value, used to index the SNMPTrapTable. INTEGER .1.3.6.1.4.1.17713.6.16.4.1.1 |
sNMPTrapIPAddressThe IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute.rw IpAddress .1.3.6.1.4.1.17713.6.16.4.1.2 |
sNMPTrapPortNumberDestination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute.rw INTEGER .1.3.6.1.4.1.17713.6.16.4.1.3 |
sNMPTrapVersionThe SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attributerw Enumeration .1.3.6.1.4.1.17713.6.16.5 |
sNMPEnabledTrapsThis controls which SNMP Traps the unit will sendrw Bits .1.3.6.1.4.1.17713.6.16.6 |
enabledDiagnosticAlarmsControls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributesrw Bits .1.3.6.1.4.1.17713.6.16.7 |
sntp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.17 |
sNTPStateSNTP control staterw Enumeration .1.3.6.1.4.1.17713.6.17.1 |
sNTPPollIntervalThe SNTP server polling intervalrw INTEGER .1.3.6.1.4.1.17713.6.17.4 |
sNTPSyncIf SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTPro Enumeration .1.3.6.1.4.1.17713.6.17.5 |
sNTPLastSyncLast SNTP sync timero Integer32 .1.3.6.1.4.1.17713.6.17.6 |
systemClockSystem clock presented as local timero Integer32 .1.3.6.1.4.1.17713.6.17.7 |
timeZoneTime zone offsets from Greenwich Mean Time (GMT)rw Enumeration .1.3.6.1.4.1.17713.6.17.8 |
daylightSavingDaylight Saving Timerw Enumeration .1.3.6.1.4.1.17713.6.17.9 |
sNTPPrimaryServerSpecifies the primary SNTP server, determining the order in which the servers are tried.rw Enumeration .1.3.6.1.4.1.17713.6.17.10 |
sNTPPrimaryServerDeadTimeTime (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer.rw INTEGER .1.3.6.1.4.1.17713.6.17.11 |
sNTPServerRetriesNumber of times the PTP will retry after an SNTP server fails to respond.rw INTEGER .1.3.6.1.4.1.17713.6.17.12 |
sNTPServerTimeoutTime (in seconds) the PTP will wait for a response from an SNTP server.rw INTEGER .1.3.6.1.4.1.17713.6.17.13 |
sNTPServerTableNumberNumber of entries in the SNTPServerTable.ro INTEGER (2) .1.3.6.1.4.1.17713.6.17.14 |
sNTPServerTable SEQUENCE OF SNTPServerTableEntry .1.3.6.1.4.1.17713.6.17.15 |
sNTPServerTableEntryTable SNTPServerTable SNTPServerTableEntry .1.3.6.1.4.1.17713.6.17.15.1 |
sNTPServerTableIndexIndex range for the SNTPServerTable. INTEGER .1.3.6.1.4.1.17713.6.17.15.1.1 |
sNTPServerIPAddressThe IP address of a valid SNTP serverrw IpAddress .1.3.6.1.4.1.17713.6.17.15.1.2 |
sNTPServerPortNumberThe IP port number of the SNTP server. Defaults to port 123.rw INTEGER .1.3.6.1.4.1.17713.6.17.15.1.3 |
sNTPServerStatusStatus message reflecting the state of communications with the SNTP serverro DisplayString .1.3.6.1.4.1.17713.6.17.15.1.4 |
reset OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.18 |
systemResetSetting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memoryrw Enumeration .1.3.6.1.4.1.17713.6.18.1 |
versions OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.19 |
softwareVersionCurrent software versionro DisplayString .1.3.6.1.4.1.17713.6.19.1 |
hardwareVersionHardware platform versionro DisplayString .1.3.6.1.4.1.17713.6.19.2 |
secondarySoftwareVersionSecondary software version, used when the primary software image is invalid or erasedro DisplayString .1.3.6.1.4.1.17713.6.19.3 |
bootVersionBoot code software versionro DisplayString .1.3.6.1.4.1.17713.6.19.4 |
pubStats OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.20 |
receiveDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.6.20.1 |
transmitDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.6.20.2 |
aggregateDataRateAverage data rate over the last one second interval (kbps)ro Integer32 .1.3.6.1.4.1.17713.6.20.3 |
wirelessLinkAvailabilityLink availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precisionro INTEGER .1.3.6.1.4.1.17713.6.20.4 |
wirelessLinkStatusCurrent status of the wireless linkro Enumeration .1.3.6.1.4.1.17713.6.20.5 |
byteErrorRatioReciprocal of the byte error ratio calculated since the last reset of the system countersro Integer32 .1.3.6.1.4.1.17713.6.20.6 |
receiveModulationModeDetailThe reason for the current receive modulation modero Enumeration .1.3.6.1.4.1.17713.6.20.7 |
ethernetBridgingAvailabilityLink availability bridging Ethernet traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precisionro INTEGER .1.3.6.1.4.1.17713.6.20.8 |
encryption OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.22 |
encryptionAlgorithmThe Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctlyro Enumeration .1.3.6.1.4.1.17713.6.22.1 |
tDDControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.23 |
tDDSynchronizationModeTDD Synchronization Mode selectionro Enumeration .1.3.6.1.4.1.17713.6.23.1 |
syslogControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.24 |
syslogClientEnable or disable the syslog clientro Enumeration .1.3.6.1.4.1.17713.6.24.1 |
syslogStateThe syslog service has been enabled or disabledro Enumeration .1.3.6.1.4.1.17713.6.24.2 |
supplementary OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.96 |
longitudeThe longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.rw DisplayString .1.3.6.1.4.1.17713.6.96.1 |
latitudeThe latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.rw DisplayString .1.3.6.1.4.1.17713.6.96.2 |
altitudeThe altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function.rw Integer32 .1.3.6.1.4.1.17713.6.96.3 |
ptpComplianceThe compliance statement for the Cambium PTP MIB Unknown .1.3.6.1.4.1.17713.6.97 |
ptpGroups OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.98 |
dfsGroupThe dfs object group. Unknown .1.3.6.1.4.1.17713.6.98.3 |
bridgeGroupThe bridge object group. Unknown .1.3.6.1.4.1.17713.6.98.4 |
configurationGroupThe configuration object group. Unknown .1.3.6.1.4.1.17713.6.98.5 |
ethernetGroupThe ethernet object group. Unknown .1.3.6.1.4.1.17713.6.98.6 |
telecomGroupThe telecom object group. Unknown .1.3.6.1.4.1.17713.6.98.7 |
licenceGroupThe licence object group. Unknown .1.3.6.1.4.1.17713.6.98.8 |
managementGroupThe management object group. Unknown .1.3.6.1.4.1.17713.6.98.9 |
phyControlGroupThe phyControl object group. Unknown .1.3.6.1.4.1.17713.6.98.10 |
phyStatusGroupThe phyStatus object group. Unknown .1.3.6.1.4.1.17713.6.98.12 |
alarmsGroupThe alarms object group. Unknown .1.3.6.1.4.1.17713.6.98.13 |
smtpGroupThe smtp object group. Unknown .1.3.6.1.4.1.17713.6.98.15 |
snmpControlGroupThe snmpControl object group. Unknown .1.3.6.1.4.1.17713.6.98.16 |
sntpGroupThe sntp object group. Unknown .1.3.6.1.4.1.17713.6.98.17 |
resetGroupThe reset object group. Unknown .1.3.6.1.4.1.17713.6.98.18 |
versionsGroupThe versions object group. Unknown .1.3.6.1.4.1.17713.6.98.19 |
pubStatsGroupThe pubStats object group. Unknown .1.3.6.1.4.1.17713.6.98.20 |
encryptionGroupThe encryption object group. Unknown .1.3.6.1.4.1.17713.6.98.22 |
tDDControlGroupThe tDDControl object group. Unknown .1.3.6.1.4.1.17713.6.98.23 |
syslogControlGroupThe syslogControl object group. Unknown .1.3.6.1.4.1.17713.6.98.24 |
supplementaryGroupThe supplementary object group. Unknown .1.3.6.1.4.1.17713.6.98.96 |
notificationsGroupThe notifications group. Unknown .1.3.6.1.4.1.17713.6.98.99 |
ptpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.99 |
ptpTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.17713.6.99.0 |
dfsChannelChangeTrapDFS channel change event NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.1 |
dfsImpulsiveInterferenceTrapDFS impulsive interference detected event NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.2 |
dataPortStatusTrapCurrent status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.3 |
telecomsChannelAStatusTrapCurrent status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.4 |
telecomsChannelBStatusTrapCurrent status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.5 |
channelALoopbackTrapThe loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.6 |
channelBLoopbackTrapThe loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.7 |
regionCodeTrapThe region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.8 |
installStatusTrapA non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.9 |
installArmStateTrapIndicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.10 |
unitOutOfCalibrationTrapThe unit is out of calibration NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.11 |
encryptionEnabledMismatchTrapEncryption has been enabled on one end of the wireless link but not the other NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.13 |
incompatibleRegionCodesTrapThe master and slave units have incompatible region codes. NB: Both units must have compatible license keys NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.14 |
noWirelessChannelAvailableTrapSpectrum Management was unable to locate a suitable wireless channel to operate on NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.15 |
wirelessLinkDisabledWarningTrapThe SNMP ifAdminStatus of the wireless interface has disabled wireless traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.16 |
dataPortDisabledWarningTrapThe SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.17 |
dataPortFiberStatusTrapIf the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include fiber support), the link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), or the link could not be established and LOS is detected (i.e. no optical carrier is detected). NB: a change of status may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.18 |
dataPortConfigurationMismatchTrapThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.19 |
incompatibleMasterAndSlaveTrapA non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.20 |
sNTPSyncTrapIf SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.21 |
tDDSynchronizationAlarmTrapNot Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.22 |
managementPortStatusTrapCurrent status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alert NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.23 |
managementPortDisabledWarningTrapThe SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet traffic NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.24 |
linkModeOptimizationMismatchTrapThe remote node of this link has been configured with a different link mode optimization NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.25 |
managementPortConfigurationMismatchTrapThe detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.28 |
syslogStateTrapThe syslog service has been enabled or disabled NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.30 |
syslogLocalNearlyFullTrapThe syslog local log is nearly full (90%) NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.31 |
syslogLocalWrappedTrapThe syslog local log has wrapped NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.32 |
syslogClientTrapEnable or disable the syslog client NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.33 |
secureModeAlarmTrapThe secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.34 |
ethernetBridgingStatusAlarmTrapEthernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Mode NOTIFICATION-TYPE .1.3.6.1.4.1.17713.6.99.0.35 |