CAMBIUM-PTP250-MIB
AI MIB Summary
The CAMBIUM-PTP250-MIB enables SNMP-based monitoring and management of Cambium Networks PTP250 point-to-point wireless bridges, exposing critical operational metrics such as link throughput, signal strength (RSSI/SNR), interface status, and hardware temperature. This module facilitates the tracking of RF performance parameters and device health to support proactive maintenance and troubleshooting of the wireless backhaul link.
MIB for PTP250
Main OID:
cambium.1.3.6.1.4.1.17713
123
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
123 total| Object Name |
|---|
cambiumMIB for PTP250 MODULE-IDENTITY .1.3.6.1.4.1.17713 |
ptp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.1 |
ptmp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.2 |
ptp250 OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250 |
configuration OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.1 |
iPAddressInternet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network.ro IpAddress .1.3.6.1.4.1.17713.250.1.1 |
subnetMaskA subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance.ro IpAddress .1.3.6.1.4.1.17713.250.1.2 |
gatewayIPAddressThe IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks.ro IpAddress .1.3.6.1.4.1.17713.250.1.3 |
remoteMACAddressMAC address of the PTP wireless unit forming the other end of the PTP linkro OCTET STRING .1.3.6.1.4.1.17713.250.1.4 |
masterSlaveModeThe PTP wireless link operates using a master and slave relationshipro Enumeration .1.3.6.1.4.1.17713.250.1.5 |
maximumTransmitPowerMaximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless linkro Integer32 (-15..27) .1.3.6.1.4.1.17713.250.1.6 |
antennaGainAntenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna.ro Integer32 .1.3.6.1.4.1.17713.250.1.7 |
cableLossLoss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.ro Integer32 .1.3.6.1.4.1.17713.250.1.8 |
channelBandwidthThe selected bandwidth of the transmit and receive radio channelsro Enumeration .1.3.6.1.4.1.17713.250.1.9 |
remoteIPAddressIP Address of the peer wireless unitro IpAddress .1.3.6.1.4.1.17713.250.1.10 |
linkNameName of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.ro DisplayString .1.3.6.1.4.1.17713.250.1.11 |
siteNameThis field contains a user-provided description of the site name together with any additional notesro DisplayString .1.3.6.1.4.1.17713.250.1.12 |
configuredModulationModeThe fixed modulation mode or maximum adaptive modulation mode to be used by the wireless linkro Enumeration .1.3.6.1.4.1.17713.250.1.13 |
bandThe frequency band to be used by the wireless linkro Enumeration .1.3.6.1.4.1.17713.250.1.14 |
configuredRangeConfigured distance between the two peer wireless units expressed in hundredths of a kilometer.ro Integer32 .1.3.6.1.4.1.17713.250.1.15 |
channelSelectionThe channels selected for use by the user. The current channel will be selected from this list.ro Bits .1.3.6.1.4.1.17713.250.1.16 |
vlanTaggingWhether or not to use VLAN tagging for management.ro Enumeration .1.3.6.1.4.1.17713.250.1.17 |
vlanIdVLAN ID for management.ro Integer32 .1.3.6.1.4.1.17713.250.1.18 |
vlanPriorityVLAN priority for management.ro Integer32 .1.3.6.1.4.1.17713.250.1.19 |
fixedModModeIf disabled, allows automatic modulation mode selection.ro Enumeration .1.3.6.1.4.1.17713.250.1.22 |
dualPayloadIf enabled, allows dual payload modulation modes to be selected.ro Enumeration .1.3.6.1.4.1.17713.250.1.23 |
ethernet OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.2 |
dataPortAutoNegotiationThis controls whether the local Ethernet interface configuration is automatically negotiated or forced.ro Enumeration .1.3.6.1.4.1.17713.250.2.1 |
dataPortAutoNegAdvertisementThis sets the different Ethernet configurations that will be advertised during auto negotiation.ro Bits .1.3.6.1.4.1.17713.250.2.2 |
dataPortStatusCurrent status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.250.2.3 |
dataPortSpeedAndDuplexThe current speed and duplex of the Ethernet linkro Enumeration .1.3.6.1.4.1.17713.250.2.4 |
licence OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.3 |
regionCodeThe region code prohibits the wireless unit from operating outside the regulated limits. NB: a change of state may generate an SNMP trap and/or SMTP email alertro DisplayString .1.3.6.1.4.1.17713.250.3.1 |
productVariantThe product variantro Enumeration .1.3.6.1.4.1.17713.250.3.2 |
productNameName of the product variantro DisplayString .1.3.6.1.4.1.17713.250.3.3 |
management OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.4 |
installArmStateIndicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alertro Enumeration .1.3.6.1.4.1.17713.250.4.1 |
tFTPServerIPAddressIP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedro IpAddress .1.3.6.1.4.1.17713.250.4.2 |
tFTPServerPortNumberThe port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrievedro Integer32 .1.3.6.1.4.1.17713.250.4.3 |
tFTPSoftwareUpgradeFileNameFilename of the Software Upgrade to be loaded from the TFTP Serverro DisplayString .1.3.6.1.4.1.17713.250.4.4 |
tFTPSoftwareUpgradeStatusThe current status of the TFTP Software upgrade processro Enumeration .1.3.6.1.4.1.17713.250.4.5 |
tFTPSoftwareUpgradeStatusTextDescriptive text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.250.4.6 |
tFTPSoftwareUpgradeStatusAdditionalTextAny additional text describing the status of the TFTP Software upgrade process, including any error detailsro DisplayString .1.3.6.1.4.1.17713.250.4.7 |
phyStatus OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.5 |
receivePowerReceive power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.250.5.1 |
vectorErrorThe vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.250.5.2 |
transmitPowerTransmit power expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.250.5.3 |
linkLossThe wireless link loss expressed in tenths of a dBro Integer32 (-500..500) .1.3.6.1.4.1.17713.250.5.5 |
currentChannelCurrent active channelro Integer32 .1.3.6.1.4.1.17713.250.5.6 |
extendedChannelCurrent extended channel in 40MHz modero Integer32 .1.3.6.1.4.1.17713.250.5.7 |
receiveModulationModeCurrent active receive modulation modero Enumeration .1.3.6.1.4.1.17713.250.5.8 |
transmitModulationModeCurrent active transmit modulation modero Enumeration .1.3.6.1.4.1.17713.250.5.9 |
currentFreqMHzCurrent channel frequency expressed in integer MHzro Integer32 .1.3.6.1.4.1.17713.250.5.11 |
extendedFreqMHzExtended channel frequency expressed in integer MHzro Integer32 .1.3.6.1.4.1.17713.250.5.12 |
signalStrengthRatioSignal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dBro Integer32 .1.3.6.1.4.1.17713.250.5.13 |
searchStateSearch status of the wireless unit. 'Registering' means that the unit has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the unit has not locked to an OFDM signal.ro Enumeration .1.3.6.1.4.1.17713.250.5.14 |
noiseFloorNoise floor expressed in tenths of a dBmro Integer32 .1.3.6.1.4.1.17713.250.5.15 |
radarDetectChannelChannel on which Radar has been detected. (Note that this variable is accessible-for-notify only).ro Integer32 .1.3.6.1.4.1.17713.250.5.16 |
measuredRangeMeasured distance between the two peer wireless units expressed in tenths of Km.ro Integer32 .1.3.6.1.4.1.17713.250.5.17 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.6 |
noWirelessChannelAvailableSpectrum Management was unable to locate a suitable wireless channel to operate onro Enumeration .1.3.6.1.4.1.17713.250.6.1 |
smtp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.7 |
sMTPServerIPAddressIP address of the SMTP serverro IpAddress .1.3.6.1.4.1.17713.250.7.1 |
sMTPServerPortNumberPort number of the SMTP serverro Integer32 .1.3.6.1.4.1.17713.250.7.2 |
sMTPSourceEmailAddressThe 'from' email address used when constructing the automatically generated e-mail messagero DisplayString .1.3.6.1.4.1.17713.250.7.3 |
sMTPDestinationEmailAddressThe 'to' email address used when constructing the automatically generated e-mail messagero DisplayString .1.3.6.1.4.1.17713.250.7.4 |
sMTPEnabledMessagesThis controls which SMTP messages the unit will sendro Bits .1.3.6.1.4.1.17713.250.7.5 |
snmpControl OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.8 |
sNMPCommunityTableNumberNumber of entries in the sNMPCommunityTable.ro Integer32 (2) .1.3.6.1.4.1.17713.250.8.1 |
sNMPCommunityTableSNMP community string configuration table. SEQUENCE OF SNMPCommunityTableEntry .1.3.6.1.4.1.17713.250.8.2 |
sNMPCommunityTableEntryTable SNMPCommunityTable SNMPCommunityTableEntry .1.3.6.1.4.1.17713.250.8.2.1 |
sNMPCommunityTableIndexSNMP community value, used to index the SNMPCommunityTable. Integer32 .1.3.6.1.4.1.17713.250.8.2.1.1 |
sNMPCommunityStringThe community string for this entryro OCTET STRING .1.3.6.1.4.1.17713.250.8.2.1.2 |
sNMPCommunityAccessWhether this community allows read-only or read-write accessro Enumeration .1.3.6.1.4.1.17713.250.8.2.1.3 |
sNMPCommunityOidThe OID at which the root of this community's subtree startsro OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.8.2.1.4 |
sNMPTrapTableNumberNumber of entries in the sNMPTrapTable.ro Integer32 (2) .1.3.6.1.4.1.17713.250.8.3 |
sNMPTrapTableSNMP trap configuration table. SEQUENCE OF SNMPTrapTableEntry .1.3.6.1.4.1.17713.250.8.4 |
sNMPTrapTableEntryTable SNMPTrapTable SNMPTrapTableEntry .1.3.6.1.4.1.17713.250.8.4.1 |
sNMPTrapTableIndexSNMP trap value, used to index the SNMPTrapTable. Integer32 .1.3.6.1.4.1.17713.250.8.4.1.1 |
sNMPTrapIPAddressThe IP address to which all SNMP Traps are sent.ro IpAddress .1.3.6.1.4.1.17713.250.8.4.1.2 |
sNMPTrapPortNumberDestination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver.ro Integer32 .1.3.6.1.4.1.17713.250.8.4.1.3 |
sNMPTrapCommunityThe community string for this trap entryro OCTET STRING .1.3.6.1.4.1.17713.250.8.4.1.4 |
sNMPTrapVersionThe SNMP protocol version for this trap entryro Enumeration .1.3.6.1.4.1.17713.250.8.4.1.5 |
sNMPEnabledTrapsThis controls which SNMP Traps the unit will sendro Bits .1.3.6.1.4.1.17713.250.8.6 |
ntp OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.9 |
nTPStateNTP control statero Enumeration .1.3.6.1.4.1.17713.250.9.1 |
nTPPollIntervalThe NTP server polling intervalro Integer32 .1.3.6.1.4.1.17713.250.9.2 |
nTPSyncIf NTP Sync fails then check the server settings in the Remote Management page, or disable NTPro Enumeration .1.3.6.1.4.1.17713.250.9.3 |
nTPLastSyncLast NTP sync timero Integer32 .1.3.6.1.4.1.17713.250.9.4 |
systemClockSystem clock presented as local timero Integer32 .1.3.6.1.4.1.17713.250.9.5 |
timeZoneTime zone offsets from Greenwich Mean Time (GMT)ro Enumeration .1.3.6.1.4.1.17713.250.9.6 |
nTPServerIpSpecifies the NTP server IP address.ro IpAddress .1.3.6.1.4.1.17713.250.9.7 |
nTPServerPortNumberPort number of the NTP serverro Integer32 .1.3.6.1.4.1.17713.250.9.8 |
versions OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.10 |
softwareVersionCurrent software versionro DisplayString .1.3.6.1.4.1.17713.250.10.1 |
hardwareVersionHardware platform versionro DisplayString .1.3.6.1.4.1.17713.250.10.2 |
bootVersionBoot code software versionro DisplayString .1.3.6.1.4.1.17713.250.10.3 |
pubStats OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.11 |
receiveDataRateAverage data rate over the last one second interval (tenths of Mbps)ro Integer32 .1.3.6.1.4.1.17713.250.11.1 |
transmitDataRateAverage data rate over the last one second interval (tenths of Mbps)ro Integer32 .1.3.6.1.4.1.17713.250.11.2 |
aggregateDataRateAverage data rate over the last one second interval (tenths of Mbps)ro Integer32 .1.3.6.1.4.1.17713.250.11.3 |
wirelessLinkStatusCurrent status of the wireless linkro Enumeration .1.3.6.1.4.1.17713.250.11.4 |
ptpComplianceThe compliance statement for the Cambium Networks PTP MIB Unknown .1.3.6.1.4.1.17713.250.97 |
ptpGroups OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.98 |
configurationGroupThe configuration object group. Unknown .1.3.6.1.4.1.17713.250.98.5 |
ethernetGroupThe ethernet object group. Unknown .1.3.6.1.4.1.17713.250.98.6 |
licenceGroupThe licence object group. Unknown .1.3.6.1.4.1.17713.250.98.8 |
managementGroupThe management object group. Unknown .1.3.6.1.4.1.17713.250.98.9 |
phyStatusGroupThe phyStatus object group. Unknown .1.3.6.1.4.1.17713.250.98.12 |
alarmsGroupThe alarms object group. Unknown .1.3.6.1.4.1.17713.250.98.13 |
smtpGroupThe smtp object group. Unknown .1.3.6.1.4.1.17713.250.98.15 |
snmpControlGroupThe snmpControl object group. Unknown .1.3.6.1.4.1.17713.250.98.16 |
ntpGroupThe ntp object group. Unknown .1.3.6.1.4.1.17713.250.98.17 |
versionsGroupThe versions object group. Unknown .1.3.6.1.4.1.17713.250.98.19 |
pubStatsGroupThe pubStats object group. Unknown .1.3.6.1.4.1.17713.250.98.20 |
notificationsGroupThe notifications group. Unknown .1.3.6.1.4.1.17713.250.98.99 |
ptpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.99 |
ptpTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.17713.250.99.0 |
dataPortStatusTrapStatus of the Ethernet link has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.17713.250.99.0.1 |
installArmStateTrapUnit install arm state has changed NOTIFICATION-TYPE .1.3.6.1.4.1.17713.250.99.0.2 |
noWirelessChannelAvailableTrapWireless channel availability has changed NOTIFICATION-TYPE .1.3.6.1.4.1.17713.250.99.0.3 |
linkStatusTrapWireless link status has changed NOTIFICATION-TYPE .1.3.6.1.4.1.17713.250.99.0.4 |
radarDetectTrapRadar has been detected on one or more channels NOTIFICATION-TYPE .1.3.6.1.4.1.17713.250.99.0.5 |