CADANT-CMTS-POLICY-MIB
AI MIB Summary
The CADANT-CMTS-POLICY-MIB enables monitoring and configuration of Quality of Service (QoS) policy parameters and traffic shaping constants on Arris Cadant C4 Cable Modem Termination Systems (CMTS). It provides access to specific policy definitions, including bandwidth limits, priority queues, and service flow attributes required for managing upstream and downstream data traffic on DOCSIS networks.
Arris Cadant C4 CMTS policy parameters and constants
Main OID:
cadPolicyMib.1.3.6.1.4.1.4998.1.1.35.1
167
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
167 total| Object Name |
|---|
cadPolicyMibArris Cadant C4 CMTS policy parameters and constants MODULE-IDENTITY .1.3.6.1.4.1.4998.1.1.35.1 |
cadScmAccessTableA table contains SCM access control list information. Each physical interface is associated with the access list number defined as hjpolAccListNumber in hjpolAccListTable of NETPLANE-POLICY-MIB. With this information, C4 can permit/deny access usnig access list filtering before the packet reach SCM from the specified physical interface. SEQUENCE OF CadScmAccessEntry .1.3.6.1.4.1.4998.1.1.35.1.1 |
cadScmAccessEntryA conceptual row containing information about SCM access list for each physical interface. CadScmAccessEntry .1.3.6.1.4.1.4998.1.1.35.1.1.1 |
cadScmAccIfIndexThe value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which SCM access control is applied InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.35.1.1.1.1 |
cadScmAccListNumberThe value of this object identifies entry(or entries) in the hjpolAccListTable. The identified entry(or entries) contains SCM access parameters to be used when filtering traffic from individual interface sent to SCM.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.1.1.2 |
cadScmAccRowStatusControl Object for row creation and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.1.1.3 |
cadDistListInTableDistribute List In Table SEQUENCE OF CadDistListInEntry .1.3.6.1.4.1.4998.1.1.35.1.2 |
cadDistListInEntryA row in Distribute List In table CadDistListInEntry .1.3.6.1.4.1.4998.1.1.35.1.2.1 |
cadDistListInProtocolProtocol for which distribute list is applied.ro CadPolicyProtocol .1.3.6.1.4.1.4998.1.1.35.1.2.1.1 |
cadDistListInProtocolProcessVRF for which distribute list is applied.ro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.2.1.2 |
cadDistListInIfIndexInterface for which distribute list is applied. The value will be 1 if the distribute list is applied to all interfaces.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.35.1.2.1.3 |
cadDistListInAccessListNumThe configured distribute in list refers to the access list specified.ro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.2.1.4 |
cadDistListInAccessListNameName of the access list referred by distribute in list.rw OCTET STRING .1.3.6.1.4.1.4998.1.1.35.1.2.1.5 |
cadDistListInStatusThe row status variable, used according to row installation and removal conventions. Once access list specified default row status is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.2.1.6 |
cadPolicyRateLimitTableA table of rate limiting policies applied to a physical interface. SEQUENCE OF CadPolicyRateLimitEntry .1.3.6.1.4.1.4998.1.1.35.1.4 |
cadPolicyRateLimitEntryAn ordered list of the rate limit polices CadPolicyRateLimitEntry .1.3.6.1.4.1.4998.1.1.35.1.4.1 |
cadPolicyRateLimitIfIndexThe value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which the rate limit policy is applied InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.35.1.4.1.1 |
cadPolicyRateLimitDirectionDirection of traffic on interface to apply the rate limit policy CadIfDirection (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.4.1.2 |
cadPolicyRateLimitIndexIndex of rate limit policy. Policies are applied in the order specified by this index value INTEGER .1.3.6.1.4.1.4998.1.1.35.1.4.1.3 |
cadPolicyRateLimitStatusCreate and delete table row entries.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.4.1.4 |
cadPolicyRateLimitAclTypeType of ACL associated with rate limit policyrw CadAclType (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.4.1.5 |
cadPolicyRateLimitAclNumACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IP traffic matches the policy.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.4.1.6 |
cadPolicyRateLimitBpsAverage rate, in bits per second (bps).rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.4.1.7 |
cadPolicyRateLimitBurstNormalNormal burst size, in bytes. The minimum value is bps divided by 2000.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.4.1.8 |
cadPolicyRateLimitBurstMaxExcess burst size, in bytes. Must be equal to or larger than cadPolicyRateLimitBurstNormalrw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.4.1.9 |
cadPolicyRateLimitConformActionAction to take on packets that conform to the specified rate limit.rw CadPolicyRateLimitAction .1.3.6.1.4.1.4998.1.1.35.1.4.1.10 |
cadPolicyRateLimitConformValueValue to set if action is set-prec-transmit, set-dscp-transmit or set-priority-transmit. For set-priority-transmit,the valid value range is 0-7.rw INTEGER .1.3.6.1.4.1.4998.1.1.35.1.4.1.11 |
cadPolicyRateLimitExceedActionAction to take on packets that exceed to the specified rate limit.rw CadPolicyRateLimitAction .1.3.6.1.4.1.4998.1.1.35.1.4.1.12 |
cadPolicyRateLimitExceedValueValue to set if action is set-prec-transmit, set-dscp-transmit or set-priority-transmit. For set-priority-transmit,the valid value range is 0-7.rw INTEGER .1.3.6.1.4.1.4998.1.1.35.1.4.1.13 |
cadPolicyRateLimitClearCountsIf set to true, clear the counts in the CadPolicyRateLimitStatusEntry. When read, this field always returns false. The correct way to clear the counts is to first read them, then set ClearCounts to true.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.4.1.14 |
cadPolicyRateLimitStatusTableA table of counts of rate limiting policies applied to a physical interface. SEQUENCE OF CadPolicyRateLimitStatusEntry .1.3.6.1.4.1.4998.1.1.35.1.5 |
cadPolicyRateLimitStatusEntryDyanmic status associated with a rate limit policy CadPolicyRateLimitStatusEntry .1.3.6.1.4.1.4998.1.1.35.1.5.1 |
cadPolicyRateLimitConformPacketsNumber of packets conforming to the policy ratero Counter64 .1.3.6.1.4.1.4998.1.1.35.1.5.1.1 |
cadPolicyRateLimitConformBytesNumber of bytes conforming to the policy ratero Counter64 .1.3.6.1.4.1.4998.1.1.35.1.5.1.2 |
cadPolicyRateLimitExceedPacketsNumber of packets exceeding to the policy ratero Counter64 .1.3.6.1.4.1.4998.1.1.35.1.5.1.3 |
cadPolicyRateLimitExceedBytesNumber of bytes exceeding to the policy ratero Counter64 .1.3.6.1.4.1.4998.1.1.35.1.5.1.4 |
cadPolicyRateLimitCurrentBurstThe current number of bytes in the burst exceeding the average bps ratero Integer32 .1.3.6.1.4.1.4998.1.1.35.1.5.1.5 |
cadPolicyRateLimitLastClearedThe value of SysUptime when the rate limit counters were last cleared.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.5.1.6 |
cadPolicyAclTableA table contains access control list (ACL) information. Each row corresponds to an access control entry (ACE), and each ACL may have multiple ACEs that are applied in order to the packet being inspected. SEQUENCE OF CadPolicyAclEntry .1.3.6.1.4.1.4998.1.1.35.1.6 |
cadPolicyAclEntryA conceptual row containing information about SCM access list for each physical interface. CadPolicyAclEntry .1.3.6.1.4.1.4998.1.1.35.1.6.1 |
cadAclNumberIPv6 ACL number. IPv6 ACLs are in the range 200-399. Extended ACL number. Extended ACLs are in the range 100-199. Standard ACLs are in the range 1-99. Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.1 |
cadAclIndexOrder in which this ACE is used in the ACL. Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.2 |
cadAclTypeIndicates whether this EACE is used as a standard, extended, or remark ACL. The rate-limiting type is not valid for this table. Remark is the only valid type that can be set, standard and extended are set by the agent when the ACE is created.rw CadAclType (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.3 |
cadAclStatusRowStatus used to add and remove ACEs. ACEs that contain only remarks should have their status set to notInService and should be created with createAndWait.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.4 |
cadAclPermitPermit or Deny the packet when matched.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.5 |
cadAclProtocolProtocol number to matchrw CadProtocolType (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.6 |
cadAclSrcIpSource IP address to matchrw InetAddressIPv4or6 (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.7 |
cadAclSrcIpMaskSource IP wildcard mask to match. Default to match anythingrw InetAddressIPv4or6 (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.8 |
cadAclSrcPortOpSource port condition (lt,gt,eq,ne) to match.rw CadExtAclCondition (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.9 |
cadAclSrcPortLoFirst Source port number to match. -1 indicates that this field is not used.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.10 |
cadAclSrcPortHiSecond Source port number to match. -1 indicates that this field is not used.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.11 |
cadAclDstIpDestination IP address to matchrw InetAddressIPv4or6 (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.12 |
cadAclDstIpMaskDestination IP wildcard (inverse) mask to match. Default to match anything.rw InetAddressIPv4or6 (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.13 |
cadAclDstPortOpDestination port condition (lt,gt,eq,ne) to match.rw CadExtAclCondition (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.14 |
cadAclDstPortLoFirst Destination port number to match. -1 indicates that this field is not used.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.15 |
cadAclDstPortHiSecond Destination port number to match. -1 indicates that this field is not usedrw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.16 |
cadAclLoggingTurn on or off the ACE matching logrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.17 |
cadAclProtoTypeSub-protocol qualifiers. For protocol type ICMP, this value matches the ICMP message type (0 - 255). For IGMP, this value matches the IGMP message type (0-15). A value of -1 means that this field is not used.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.18 |
cadAclProtoCodeSub-protocol qualifiers. For protocol type ICMP, this value matches the ICMP message type code (0 - 255). A value of -1 indicates this value is not used.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.6.1.19 |
cadAclIpTosMatches the TOS field of the IP header.rw CadIpTos (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.20 |
cadAclIpTosMaskMask to apply to the IpTos object when finding a mactch on the TOS field of the IP header. A value of 0 is used to indicate that the TOS is not used.rw CadIpTosMask (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.21 |
cadAclTcpFlagsMatches the flags field of the TCP header.rw CadTcpFlags (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.22 |
cadAclTcpFlagsMaskMask to apply to the TcpFlags object when finding a mactch on the flags field of the TCP header.rw CadTcpFlags (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.23 |
cadAclFragmentsIndicates whether this EACE applies to noninitial fragments of packets. The default is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.24 |
cadAclRemarkThe comment associated with the access control entry. This is only valid for ACEs of type remark.rw CadAclString (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.6.1.26 |
cadAclIpAddrTypeIP Address typerw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4998.1.1.35.1.6.1.27 |
cadSnmpCommAccessTableA table contains the access list information associated with the community string. Each community string defined in snmpCommunithTable can be configured with one access list number. C4 can permit/deny access usnig access list filtering. Filtering will occur in software, after the SNMP traffic passed through the OSE protocol stack and received by the agent. Standard ACLs will be used to enforce the access restrictions SEQUENCE OF CadSnmpCommAccessEntry .1.3.6.1.4.1.4998.1.1.35.1.7 |
cadSnmpCommAccessEntryA conceptual row containing information about access list filtering associated with community string. CadSnmpCommAccessEntry .1.3.6.1.4.1.4998.1.1.35.1.7.1 |
cadSnmpCommAccessNameThe index value that uniquely identifies an entry in snmpCommunityTable. SnmpAdminString .1.3.6.1.4.1.4998.1.1.35.1.7.1.1 |
cadSnmpCommAccessListThe value of this object identifies entry (or entries) in the cadPolicyAclTable. The identified entry (or entries) contains access parameters to be used when filtering traffic sent to SNMP agent.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.7.1.2 |
cadSnmpCommAccessStatusControl Object for row creation and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.7.1.3 |
cadPolicyAccessGroupTableA table of access group policies applied to a physical interface. SEQUENCE OF CadPolicyAccessGroupEntry .1.3.6.1.4.1.4998.1.1.35.1.8 |
cadPolicyAccessGroupEntryAn ordered list of the access group polices CadPolicyAccessGroupEntry .1.3.6.1.4.1.4998.1.1.35.1.8.1 |
cadPolicyAccessGroupIfIndexThe value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which the access group policy is applied InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.35.1.8.1.1 |
cadPolicyAccessGroupDirectionDirection of traffic on interface to apply the access group policy CadIfDirection (CADANT-TC) .1.3.6.1.4.1.4998.1.1.35.1.8.1.2 |
cadPolicyAccessGroupStatusThis table supports sets of createAndGo(4) and destroy(6)rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.8.1.3 |
cadPolicyAccessGroupIpv4AclNumACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IPv4 traffic matches the policy.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.8.1.4 |
cadPolicyAccessGroupClearCountsIf set to true, clear the counts in the CadPolicyAccessGroupStatusEntry. When read, this field always returns false. The correct way to clear the counts is to first read them, then set ClearCounts to true.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.8.1.5 |
cadPolicyAccessGroupIpv6AclNumACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IPv6 traffic matches the policy.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.8.1.6 |
cadPolicyAccessGroupIpv6AclNameACL name.rw SnmpAdminString .1.3.6.1.4.1.4998.1.1.35.1.8.1.7 |
cadPolicyAccessGroupStatusTableA table of counts of rate limiting policies applied to a physical interface. SEQUENCE OF CadPolicyAccessGroupStatusEntry .1.3.6.1.4.1.4998.1.1.35.1.9 |
cadPolicyAccessGroupStatusEntryDyanmic status associated with a rate limit policy CadPolicyAccessGroupStatusEntry .1.3.6.1.4.1.4998.1.1.35.1.9.1 |
cadPolicyAccessGroupPermitPacketsNumber of packets conforming to the access group policy permit ACLro Counter64 .1.3.6.1.4.1.4998.1.1.35.1.9.1.1 |
cadPolicyAccessGroupDenyPacketsNumber of packets conforming to the access group policy deny ACLro Counter64 .1.3.6.1.4.1.4998.1.1.35.1.9.1.2 |
cadPolicyAccessGroupLastClearedThe value of SysUptime when the access group policy counters were last cleared.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.9.1.3 |
cadPolicyPfxListTablePrefix List Table SEQUENCE OF CadPolicyPfxListEntry .1.3.6.1.4.1.4998.1.1.35.1.11 |
cadPolicyPfxListEntryA row in Prefix list table CadPolicyPfxListEntry .1.3.6.1.4.1.4998.1.1.35.1.11.1 |
cadPolicyPfxListNumberPrefix list is identified by number value of 0 should be passed for this object if prefix list is configured by namero Integer32 .1.3.6.1.4.1.4998.1.1.35.1.11.1.1 |
cadPolicyPfxListNameName of prefix list.Null value is assigned to this Object if the prefix list is identified by numberro OCTET STRING .1.3.6.1.4.1.4998.1.1.35.1.11.1.2 |
cadPolicyPfxListSeqNumberA sequence in the prefix list is identified by sequence number. If no sequence is specified defalut sequence of 5 is assumend. IF one more sequence is configured sequence number 10 is assigned (multiples of 5)ro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.11.1.3 |
cadPolicyPfxListIpAddressThis is the source ipv4 or ipv6 address on which the filtering needs to be appliedro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4998.1.1.35.1.11.1.4 |
cadPolicyPfxListIpAddMaskLenMask length of the Source IP addressro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.11.1.5 |
cadPolicyPfxListMaskGeValueIf the received route matches the source address and the mask length is greater than the value specified, apply the specified action to the routero Integer32 .1.3.6.1.4.1.4998.1.1.35.1.11.1.6 |
cadPolicyPfxListMaskLeValueThis value specifies if the received route mask length is less the value specified here do the action specified (permit/deny)ro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.11.1.7 |
cadPolicyPfxListActionspecifies the action to be taken. Possible actions include permit(1) and deny(2)rw CadPolicyAction .1.3.6.1.4.1.4998.1.1.35.1.11.1.8 |
cadPolicyPfxListStatusThe row status variable, used according to row installation and removal conventions.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.11.1.9 |
cadPolicyPfxListAfiThis is the Address Family Identifier (AFI) of the prefix that will follow. Only IPv4 or IPv6 prefix-list will be supported. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4998.1.1.35.1.11.1.10 |
cadPolicyPfxListSafiThis is the Subsequent Address Family Identifier (SAFI) of the prefix that will follow. Enumeration .1.3.6.1.4.1.4998.1.1.35.1.11.1.11 |
cadPolicyDistListOutTableDistribute List Out Table SEQUENCE OF CadPolicyDistListOutEntry .1.3.6.1.4.1.4998.1.1.35.1.12 |
cadPolicyDistListOutEntryA row in Distribute List Out table CadPolicyDistListOutEntry .1.3.6.1.4.1.4998.1.1.35.1.12.1 |
cadPolicyDistListOutSrcProtocolSource Protocol under which distribute list is configured.ro CadPolicyProtocol .1.3.6.1.4.1.4998.1.1.35.1.12.1.1 |
cadPolicyDistListOutSrcProtocolProcessSource VRF ID under which distribute list is configured.ro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.12.1.2 |
cadPolicyDistListOutRoutingProtocolDestination Protocol to which routes need to be sent.ro CadPolicyProtocol .1.3.6.1.4.1.4998.1.1.35.1.12.1.3 |
cadPolicyDistListOutRoutingProcessDestination VRF ID under which distribute list is configured.ro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.12.1.4 |
cadPolicyDistListOutAutonomousSystemNumAutonomous system number of BGP to which routes need to be redistributed. If destination protocol is BGP appropriate AS number needs to be filled for this object. Otherwise set a value of 1 for this object.ro Integer32 (-1..2147483647) .1.3.6.1.4.1.4998.1.1.35.1.12.1.5 |
cadPolicyDistListOutAccessListNumThe configured distribute out list refers to the access list specified. The access list number must be in the range of 1 - 99ro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.12.1.6 |
cadPolicyDistListOutAccessListNameName of the access list referred by distribute list. The access list name must be less than 32 charactersrw OCTET STRING .1.3.6.1.4.1.4998.1.1.35.1.12.1.7 |
cadPolicyDistListOutStatusThe row status variable, used according to row installation and removal conventions. Once access list specified default row status is UP.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.12.1.8 |
cadPolicyDistListOutIfIndexInterface for which distribute list is applied. The value will be 1 if the distribute list is applied to all interfaces.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.35.1.12.1.9 |
cadDistListOutTableDistribute List Out Table SEQUENCE OF CadDistListOutEntry .1.3.6.1.4.1.4998.1.1.35.1.13 |
cadDistListOutEntryA row in Distribute List Out table CadDistListOutEntry .1.3.6.1.4.1.4998.1.1.35.1.13.1 |
cadDistListOutVrIndexvirtual router indexro Integer32 .1.3.6.1.4.1.4998.1.1.35.1.13.1.1 |
cadDistListOutDestProtocolDestination protocol for which distribute list is applied.ro InfoSourceDest (DC-RTM-MIB) .1.3.6.1.4.1.4998.1.1.35.1.13.1.2 |
cadDistListOutSrcProtocolSource protocol for which distribute list is applied.ro InfoSourceDest (DC-RTM-MIB) .1.3.6.1.4.1.4998.1.1.35.1.13.1.3 |
cadDistListOutAccessListNumAccess List Numberrw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.13.1.4 |
cadDistListOutStatusThe row status variable, used according to row installation and removal conventions. Once access list specified default row status is active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.13.1.5 |
cadDistListOutAccessListNameAccess List Namerw SnmpAdminString .1.3.6.1.4.1.4998.1.1.35.1.13.1.6 |
cadAclNameTableThis table maps names to ACL entries. Each row associates a name with the indexed ACL. SEQUENCE OF CadAclNameEntry .1.3.6.1.4.1.4998.1.1.35.1.14 |
cadAclNameEntryA conceptual row containing name information about an ACL. CadAclNameEntry .1.3.6.1.4.1.4998.1.1.35.1.14.1 |
cadNameAclNameThe name of the access control list. SnmpAdminString .1.3.6.1.4.1.4998.1.1.35.1.14.1.1 |
cadNameAclNumberExtended ACL number. Extended ACLs are in the range 100-199. Standard ACLs are in the range 1-99. Integer32 .1.3.6.1.4.1.4998.1.1.35.1.14.1.2 |
cadNameAclStatusRowStatus used to add and remove names for ACLs. When an ACL is removed, the associated name is also removed.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.14.1.3 |
cadAclControl OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.35.1.15 |
cadAclOrderAclThis variable always returns false(2) upon reading. When set to true(1), the ACL identified in cadAclOrderAclIndex is renumbered with interval cadAclOrderAclInterval.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.15.1 |
cadAclOrderAclIndexThis variable identifies the ACL that should be renumbered.rw INTEGER .1.3.6.1.4.1.4998.1.1.35.1.15.2 |
cadAclOrderAclIntervalThis variable specifies the numbering interval used between each ACE when reordering an ACL.rw INTEGER .1.3.6.1.4.1.4998.1.1.35.1.15.3 |
cadAclOrderAclStartThis variable specifies the index that ACL reordering will use as the base for the first ACE.rw INTEGER .1.3.6.1.4.1.4998.1.1.35.1.15.4 |
cadAclClearIpv4AclCountsThis variable specifies the access list number for which all IPv4 per-entry counts will be cleared. This number may correspond to an individual access list (1..199). Setting to '0' will cause the per-entry counts to be cleared for ALL IPv4 configured access lists. This variable always returns '0' upon readingrw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.15.5 |
cadAclClearIpv6AclCountsThis variable specifies the access list number for which all IPv6 per-entry counts will be cleared. This number may correspond to an individual access list (200..399). Setting to '0' will cause the per-entry counts to be cleared for ALL IPv6 configured access lists. This variable always returns '0' upon readingrw Integer32(0 | 200..399) .1.3.6.1.4.1.4998.1.1.35.1.15.6 |
cadPolicyAclExtTableThe cadPolicyAclExtTable augments the cadPolicyAclTable with a count for total number of times the access list entry has been matched by all referencing applications. SEQUENCE OF CadPolicyAclExtEntry .1.3.6.1.4.1.4998.1.1.35.1.16 |
cadPolicyAclExtEntryInformation about the policy access list entry. CadPolicyAclExtEntry .1.3.6.1.4.1.4998.1.1.35.1.16.1 |
cadAclEntryCountTotal number of times the access list entry has been matched by all referencing applications.ro Counter64 .1.3.6.1.4.1.4998.1.1.35.1.16.1.1 |
cadPolicyRouting OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.35.1.30 |
cadRouteMapTagTableThis table maps policy route map names to route map entries. Each row associates a name with the indexed policy route map. SEQUENCE OF CadRouteMapTagEntry .1.3.6.1.4.1.4998.1.1.35.1.30.1 |
cadRouteMapTagEntryA conceptual row containing name information for a policy route map. CadRouteMapTagEntry .1.3.6.1.4.1.4998.1.1.35.1.30.1.1 |
cadRouteMapTagNameName to used for this policy route map SnmpAdminString .1.3.6.1.4.1.4998.1.1.35.1.30.1.1.1 |
cadRouteMapTagIdId used to associate entries in the policy route map table to this name.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.30.1.1.2 |
cadRouteMapTagRowStatusThe row status variable used according to row installation and removal convention. In our case, we have simplified this to the usage of only the following states - active, createAndGo, and destroy. Other three states notInService, notReady and createAndWait are not permitted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.1.1.3 |
cadRouteMapTableThis table contains policy route map data where each row contains information about the ACL being used and what set operations should be applied to the IP packet on a match. SEQUENCE OF CadRouteMapEntry .1.3.6.1.4.1.4998.1.1.35.1.30.2 |
cadRouteMapEntryA conceptual row containing information for a policy route map entry. CadRouteMapEntry .1.3.6.1.4.1.4998.1.1.35.1.30.2.1 |
cadRouteMapIdId used to associate entries in the policy route map table. Integer32 .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.1 |
cadRouteMapSeqNumSequence number used to order the match statements. Integer32 .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.2 |
cadRouteMapMatchTypeType of match to used for this entry. Permit matches on the provided ACL and then applies the defined set operations before destination routing. Deny matches on the provided ACL and then directly routes to the destination without applying any of the set critera to the packet.rw Enumeration .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.3 |
cadRouteMapMatchAclACL used to match the incoming packet. Since IPv4 is the only supported address type, the ACL number must be an extended or standard ACL. A value 0 implies that no ACL is used and all packets will match this entry.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.4 |
cadRouteMapSetIpPrecIndicates whether the IP Precedence should be changed on the packet if it matches the ACL and this is a permit type of match.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.5 |
cadRouteMapIpPrecThe IP precedence value that should be used to replace the existing IP precedence of the matching packet.rw Enumeration .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.6 |
cadRouteMapSetIpTosIndicates whether the IP TOS should be changed on the packet if it matches the ACL and this is a permit type of match.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.7 |
cadRouteMapIpTosThe IP TOS value that should be used to replace the existing IP TOS of the matching packet.rw Enumeration .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.8 |
cadRouteMapSetNextHopIndicates whether the next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.9 |
cadRouteMapNextHopAddrTypeThe address type of the next hop and backup next hop addresses. Currently IPv4 is the only supported address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.10 |
cadRouteMapNextHopThe address of the adjacent next hop router to use in forwading the matching packet. The next hop router address must be the address of an ajacent router, and the routing table (VRF?) is used to verify that the address can be directly reached. Only IPv4 addresses are currently supported.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.11 |
cadRouteMapSetBackupNextHopIndicates whether the backup next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet. This only would be done if the primary next hop was not set or was unreachable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.12 |
cadRouteMapBackupNextHopThe address type of a second next hop, that can be used only if the primary next hop address can not be reached. Only Ipv4 addresses are currently supported.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.13 |
cadRouteMapSetNullInterfaceIf set to true and the packet matches the ACL, it will be dropped.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.14 |
cadRouteMapRowStatusThe row status variable used according to row installation and removal convention. In our case, we have simplified this to the usage of only the following states - active, createAndGo, and destroy. Other three states notInService, notReady and createAndWait are not permitted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.15 |
cadRouteMapSetIpDscpIndicates whether the IP DSCP should be changed on the packet if it matches the ACL and this is a permit type of match.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.16 |
cadRouteMapIpDscpThe IP DSCP value that should be used to replace the existing IP DSCP of the matching packet.rw INTEGER .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.17 |
cadRouteMapSetRecursiveNextHopIndicates whether the recursive next hop setting should be used to specify the next hop for the remote router when forwarding the matching packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.18 |
cadRouteMapRecursiveNextHopThe address type of a remote router next hop, that is used to perform a recursive route lookup. Only Ipv4 addresses are currently supported.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.19 |
cadRouteMapStatsTableThis table contains policy route map counts where each row contains information about the number of packets that match the specified ACL and were successfully changed with the defined set operations, as well as those that matched the ACL but failed the set operations. SEQUENCE OF CadRouteMapStatsEntry .1.3.6.1.4.1.4998.1.1.35.1.30.3 |
cadRouteMapStatsEntryA conceptual row containing counts information for a policy route map entry. CadRouteMapStatsEntry .1.3.6.1.4.1.4998.1.1.35.1.30.3.1 |
cadRouteMapPktMatchedThe number of packets that match the ACL defined in the route map entry and where the action was also successful. For matches of type deny, the packet is routed by destination, and for packets of type match, the packet is successfully modified and sent.ro Counter32 .1.3.6.1.4.1.4998.1.1.35.1.30.3.1.1 |
cadRouteMapByteMatchedThe number of bytes that match the ACL defined in the route map entry and where the action was also successful. For matches of type deny, the packet is routed by destination, and for packets of type match, the packet is successfully modified and sent.ro Counter64 .1.3.6.1.4.1.4998.1.1.35.1.30.3.1.2 |
cadRouteMapPktFailedThe number of packets that match the ACL defined in the route map entry and where the action failed. For route map entries of type match, the set operation failed.ro Counter32 .1.3.6.1.4.1.4998.1.1.35.1.30.3.1.3 |
cadRouteMapByteFailedThe number of packets that match the ACL defined in the route map entry and where the action failed. For route map entries of type match, the set operation failed.ro Counter64 .1.3.6.1.4.1.4998.1.1.35.1.30.3.1.4 |
cadRouteMapClearStatsSetting this value will reset all the byte and packet counts for a route map. A value of 0 indicates no reset is performed.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.30.4 |
cadLocalPolicyRouteMapThis value contains the mapId of the policy route map to be used for local policy based routing. A value of 0 indicates no local policy routing is performed.rw Integer32 .1.3.6.1.4.1.4998.1.1.35.1.30.5 |