BIANCA-BRICK-X21-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for BIANCA-BRICK-X21-MIB.
31
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
31 total| Object Name |
|---|
org OBJECT IDENTIFIER .1.3 |
RFC1155-SMI Unknown .1.3 |
dod OBJECT IDENTIFIER .1.3.6 |
internet OBJECT IDENTIFIER .1.3.6.1 |
private OBJECT IDENTIFIER .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
bintec OBJECT IDENTIFIER .1.3.6.1.4.1.272 |
bibo OBJECT IDENTIFIER .1.3.6.1.4.1.272.4 |
x21 OBJECT IDENTIFIER .1.3.6.1.4.1.272.4.10 |
x21IfTableThe x21IfTable contains information relating to the
interfaces found on the system. Each entry corresponds to
a connected X21 interface. Entries can only be added or
deleted by the system.
Creating entries: Entries are created by the system
only when a new X21 module is installed.
Deleting entries: Entries are removed by the system
after the appropriate X21 module is removed. SEQUENCE OF X21IfEntry .1.3.6.1.4.1.272.4.10.1 |
x21IfEntry X21IfEntry .1.3.6.1.4.1.272.4.10.1.1 |
x21IfIndexUnique index of the X21 interface.ro INTEGER .1.3.6.1.4.1.272.4.10.1.1.1 |
x21IfL1StateThe X21 physical layer state
dn(1) physical layer is inactive;
up(2) physical layer is active;ro Enumeration .1.3.6.1.4.1.272.4.10.1.1.2 |
x21IfL1ModeThe physical layer (layer 1) mode. When configured as
DCE(2) the X21 interface provides the clock.rw Enumeration .1.3.6.1.4.1.272.4.10.1.1.3 |
x21IfIfLeadsThe value of IfLeads has influence on the state of the
physical layer (L1State). When configured as
IfLeads=enabled(1), the state of the physical layer
depends on the signals of the X.21 interface pins
`Indication' and `Control'. When configured as
IfLeads=disabled(2), the state of the physical layer
stays always up.rw Enumeration .1.3.6.1.4.1.272.4.10.1.1.4 |
x21IfSpeedThe X21 interface speed in bits per second. The range
can be configured between 2Mbits and 2400 Bits per
second.rw Enumeration .1.3.6.1.4.1.272.4.10.1.1.5 |
x21IfL2ModeThe layer 2 mode. This value has influence on the
HDLC address field (first byte of a HDCL frame). When
configured as DTE(1) the address in a command frame is
0x01, when configured as DCE(2) it is 0x03. For
response frames it is vice versa. When configured as
AUTO(3), layer 2 is set to the same mode like L1Mode is
set.rw Enumeration .1.3.6.1.4.1.272.4.10.1.1.6 |
x21IfSpeedRealThe measured X21 interface speed in bits per second.ro Counter .1.3.6.1.4.1.272.4.10.1.1.7 |
x21IfRxPacketsCount of received valid Frames.ro Counter .1.3.6.1.4.1.272.4.10.1.1.8 |
x21IfRxOctetsCount of received bytes.ro Counter .1.3.6.1.4.1.272.4.10.1.1.9 |
x21IfTxPacketsCount of transmitted valid Frames.ro Counter .1.3.6.1.4.1.272.4.10.1.1.10 |
x21IfTxOctetsCount of transmitted bytes.ro Counter .1.3.6.1.4.1.272.4.10.1.1.11 |
x21IfRxResetsCount of receiver resets. Under rare circumstances it
might be necessary to reset the receiver to work
properly.ro Counter .1.3.6.1.4.1.272.4.10.1.1.12 |
x21IfRxAbortsCount of receiver aborts. The sender of a frame can
indicate a frame as aborted with a special Abort
sequence.ro Counter .1.3.6.1.4.1.272.4.10.1.1.13 |
x21IfRxOverrunsCount of receiver overruns. If the X21 card is unable
to grant sufficiently soon/often the bus, the
32-character RxFIFO may fill up. This leads to loss of
data.ro Counter .1.3.6.1.4.1.272.4.10.1.1.14 |
x21IfRxCRCErrorsCount of corrupted frames. Errors due to interference
on the X21 cable.ro Counter .1.3.6.1.4.1.272.4.10.1.1.15 |
x21IfRxGiantFramesCount of received frames with illegal framesize. This
can occur if a frame delimiter is destroyed.ro Counter .1.3.6.1.4.1.272.4.10.1.1.16 |
x21IfTxResetsCount of transmitter resets. Under rare circumstances
it might be necessary to reset the transmitter to work
properly.ro Counter .1.3.6.1.4.1.272.4.10.1.1.17 |
x21IfTxAbortsCount of transmitter aborts. While sending a frame it
might be necessary to indicate this frame as aborted. In
this case the receiver regards this frame as illegal.ro Counter .1.3.6.1.4.1.272.4.10.1.1.18 |
x21IfTxUnderrunsCount of transmitter underruns. The serial data for the
X21 card is supplied too slowly.ro Counter .1.3.6.1.4.1.272.4.10.1.1.19 |
x21IfTxGiantFramesCount of transmitted frames with illegal
framesize. This can occur if an upper module creates
packets with more than the maximum allowed packet size.ro Counter .1.3.6.1.4.1.272.4.10.1.1.20 |