BIANCA-BRICK-IP-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
185
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
185 total| Object Name |
|---|
org OBJECT IDENTIFIER .1.3 |
RFC1155-SMI Unknown .1.3 |
dod OBJECT IDENTIFIER .1.3.6 |
internet OBJECT IDENTIFIER .1.3.6.1 |
private OBJECT IDENTIFIER .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
bintec OBJECT IDENTIFIER .1.3.6.1.4.1.272 |
bibo OBJECT IDENTIFIER .1.3.6.1.4.1.272.4 |
biboip OBJECT IDENTIFIER .1.3.6.1.4.1.272.4.5 |
ipExtIfTableThe ipExtIfTable contains extended information related to
IP and the interfaces found on the system. Entries can only
be added or deleted by the system. SEQUENCE OF IpExtIfEntry .1.3.6.1.4.1.272.4.5.3 |
ipExtIfEntry IpExtIfEntry .1.3.6.1.4.1.272.4.5.3.1 |
ipExtIfIndexUnique interface indexro INTEGER .1.3.6.1.4.1.272.4.5.3.1.1 |
ipExtIfRipSendspecifies which versions of RIP messages are sent
to that interface. Usually RIP messages are sent as
broadcast, except this object is set to ripV2mcast. In
this case RIP V2 messages are sent to the multicast
address 224.0.0.9 .rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.3 |
ipExtIfRipReceivespecifies which versions of RIP messages are accepted
from that interface. RIP V2 messages are received
regardless if they are sent as broadcast or multicast.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.4 |
ipExtIfProxyArpSwitch for Proxy ARP on this interface.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.5 |
ipExtIfNatThis object can be used to switch NAT on and off for
a specific interface.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.6 |
ipExtIfNatRmvFinThis object specifies, wether entries in the IpNatTable
shall be removed, when TCP-FINS have been received and
acknowledged in both directions, a TCP-RST has been received
or a ICMP-ERROR message has been received for the entry.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.7 |
ipExtIfNatTcpTimeoutTCP NAT entries vanish unconditionally after not being
used for the amount of time specified by this object
in seconds.rw INTEGER .1.3.6.1.4.1.272.4.5.3.1.8 |
ipExtIfNatOtherTimeoutNon-TCP NAT entries vanish unconditionally after not being
used for the amount of time specified by this object
in seconds.rw INTEGER .1.3.6.1.4.1.272.4.5.3.1.9 |
ipExtIfNatOutXlatThis object can be used to switch the outgoing address
translation off. Then, all addresses are passed instead
of being translated. The session mechanism remains
active and implements a security mechanism.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.10 |
ipExtIfAccountingSwitch for accounting on the specified interface. An IP
packet is being accounted, when this object is set to
on for either the source or the destination interface.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.11 |
ipExtIfTcpSpoofingSwitch for TCP spoofing on this interface. TCP keepalive
polls are answered by the BRICK to prevent unnecessary
ISDN connections. Set this object to on for ISDN
dialup interfaces.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.12 |
ipExtIfAccessActionThis object describes the action, that is done,
when a packet received from the interface has been
filtered out. When set to ignore, no action takes
place. When set to refuse, an ICMP unreachable message
is being sent to the originator of the packet.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.13 |
ipExtIfAccessReportThis object specifies, how a packed filtered by accesslists
should be logged. When set to none, no logging takes place.
When set to info, protocol, ip-addresses and portnumbers
are logged. When set to dump, a dump of the first 64 bytes
of the packet will be written to the syslog table.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.14 |
ipExtIfOspfConfigure the OSPF status of this interface. Routing
information about routes on passive and active interfaces is
propagated on active interfaces. Only active interfaces run
the OSPF protocol. When set to off the interface and its
associated routes are invisible to the OSPF protocol.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.15 |
ipExtIfOspfMetricConfigure the metric calculation of OSPF interfaces. If set
to auto the metric is calculated based on ifSpeed. If set
to fixed the metric is taken from the ospfIfMetricTable.
Additionaly the metric adjustment for dialup interfaces
can be configured. If set to auto-adjust or fixed-adjust
the basic metric value is reduced if the operational status
of the dialup interface is up.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.16 |
ipExtIfTcpCksumEnable or disable the TCP checksum check for local packets
received on the corresponding interface. Disabling the check
may improve performance for some local applications (i.e.
remote CAPI). This object should only be set to dont-check
on interfaces for LANs without further routers. Packets
received from routers may have a corrupted TCP checksum
and TCP will no longer be able to detect those packets. The
TCP checksum must be checked by the receiving TCP under any
circumstances, when TCP header compression is used on any
router.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.17 |
ipExtIfBackRtVerifyThis object activates an additional check for incoming
packets. If set to on, incoming packets are only accepted
if return packets sent back to their source IP address
would be sent over the same interface. This prevents
packets being passed from untrusted interfaces to this
interface.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.18 |
ipExtIfRuleIndexThis object defines the index of the first access rule
that is applied for incoming packets. If set to 0 or if
there is no access rule with this index no access rules
are applied for this interface.rw INTEGER .1.3.6.1.4.1.272.4.5.3.1.19 |
ipExtIfAuthenticationThis object defines the authentication scheme used for
incoming packets.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.20 |
ipExtIfAuthModeThis object defines the authentication mode. If set to strict
each source IP address must be authenticated. If set to
loose all source IP addresses are allowed if at least one
IP address is successfully authenticated.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.21 |
ipExtIfAuthLifeTimeThis object defines the time in seconds a successful
authentication is valid since the IP partner was
authenticated.rw INTEGER .1.3.6.1.4.1.272.4.5.3.1.22 |
ipExtIfAuthKeepaliveThis object defines the period between short authentications
that are invisible to the userrw INTEGER .1.3.6.1.4.1.272.4.5.3.1.23 |
ipExtIfRouteAnnounceThis object defines the condition when routes on this
interface are propagated by routing protocols.
If set to up-only routes are only propagated
if the operational status of the interface is up. If set
to up-dormant routes are propagated if the status is
up or dormant. If set to always routes are propagated
independent of the operational status.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.24 |
ipExtIfIpFragmentationThis object defines different modes used for fragmentation
of IP datagrams greater than the MTU of the destination
interface. If set to enabled (1) each IP datagram will be
splitted into a first fragment MTU sized and the last one
smaller than the first. If set to disabled (2) an ICMP
unreachable message will be performed. The equal (3) mode
defines a fragmentation technique wich generates fragments
having approximately the same size whereon the reverse (4)
mode starts with a small fragment followed by MTU sized
fragment(s).rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.25 |
ipExtIfReroutingThis object enables or disables rerouting on this interface.
The default value is enabled. If set to disabled, then only
the better one route from two or more possible routes is
chosen, even if the ifOperStatus of the interface for this
route is dormant.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.26 |
ipExtIfBodRuleIndexThis object defines the index of the first rule used for
Bandwidth on Demand (BOD) that is applied for incoming and/or
outgoing traffic. If set to 0 or if there is no entry in
the ipBodRuleTable with this index no BOD-specific information
is applied for this interface.rw INTEGER .1.3.6.1.4.1.272.4.5.3.1.27 |
ipExtIfQosRuleIndexThis object defines the index of the first rule used for
Qos (Qualtiy of Service) rules applied for IP traffic.
If set to 0 or if there is no entry in the ipQoSTable with
this index no QoS-specific information is applied for this
interface.rw INTEGER .1.3.6.1.4.1.272.4.5.3.1.28 |
ipExtIfIpsecAccountingThis object determines, whether packets which are en- or
decapsulated by IPSec should be accounted with encapsulation
header(ipsec) or without the encapsulation header (clear),
or even twice (both).rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.29 |
ipExtIfMulticastEnable that multicast frames are accepted
from that interface.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.30 |
ipExtIfNatSilentDenyThis object specifies - if NAT is enabled (see ipExtIfNat) -
wether incoming IP packets not passed by the NAT barrier
should answered with an ICMP Host Unreachable or TCP RST
message addressed to to packet originator. If set to
enabled(2), such incoming IP packets will be silently
discarded.rw Enumeration .1.3.6.1.4.1.272.4.5.3.1.31 |
ipExtRtTableThe ipExtRtTable can be used in addition (not instead of)
to the ipRouteTable to specify routing of IP datagrams.
The selection of datagram-types is more specific with
the ipExtRtTable, so routing of different services over different pathes is possible. The specification of local
IP-addresses is not possible in the ipExtRtTable.
The ipExtRtTable will be searched before the ipRouteTable.
If a matching entry is found, it will be taken for routing
and no further lookup in the ipRouteTable will happen. SEQUENCE OF IpExtRtEntry .1.3.6.1.4.1.272.4.5.4 |
ipExtRtEntryEach entry in the ipExtRtTable describes a set of IP
datagrams and the destination interface for that set.
Metric parameters allow for ordering of the different
specifications for overlapping sets. IpExtRtEntry .1.3.6.1.4.1.272.4.5.4.1 |
ipExtRtProtocolThis object specifies the value of the protocolfield in
the ip header for all IP-datagrams belonging to the set.
If this object is set to dont-verify, the value of the
protocol field is not specified and can take any value.rw Enumeration .1.3.6.1.4.1.272.4.5.4.1.1 |
ipExtRtSrcIfIndexThis object specifies the source index of the IP-datagrams.
If this object has a value other than 0, only datagrams
received over the interface with the appropriate interface
index are considered to be part of the set. If this object
is set to 0, the source interface index for the datagrams
belonging to the set is not specified.rw INTEGER .1.3.6.1.4.1.272.4.5.4.1.2 |
ipExtRtSrcAddrThis object describes together with ipExtRtSrcMask the
range of the source-addresses of the IP-datagrams belonging
to the set. If both objects are set to 0.0.0.0 the source-
addresses for the datagrams in the set is not specified
and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.4.1.3 |
ipExtRtSrcMaskThis object describes together with ipExtRtSrcAddr the
range of the source-addresses of the IP-datagrams belonging
to the set. If both objects are set to 0.0.0.0 the source-
addresses for the datagrams in the set is not specified
and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.4.1.4 |
ipExtRtSrcPortThis object describes together with ipExtRtSrcPortRange the
range of source portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the source
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.4.1.5 |
ipExtRtSrcPortRangeThis object describes together with ipExtRtSrcPort the
range of source portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the source
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.4.1.6 |
ipExtRtDstAddrThis object describes together with ipExtRtDstMask the
range of the target-addresses of the IP-datagrams belonging
to the set. If both objects are set to 0.0.0.0 the target-
addresses for the datagrams in the set is not specified
and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.4.1.7 |
ipExtRtDstMaskThis object describes together with ipExtRtDstAddr the
range of the target-addresses of the IP-datagrams belonging
to the set. If both objects are set to 0.0.0.0 the target-
addresses for the datagrams in the set is not specified
and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.4.1.8 |
ipExtRtDstPortThis object describes together with ipExtRtDstPortRange the
range of target-portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the target
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.4.1.9 |
ipExtRtDstPortRangeThis object describes together with ipExtRtDstPort the
range of target-portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the target
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.4.1.10 |
ipExtRtTosThis object describes together with ipExtRtTosMask the
range of the Type of Service field (TOS) in the IP-header
of the IP-datagrams belonging to the set. A TOS value is
considered within the range, when the following equation
is valid:
(tos & ipExtRtTosMask) == (ipExtRtTos & ipExtRtTosMask)
If both objects are set to 0 the TOS value of the datagrams
in the set is not specified and can take any value.rw INTEGER .1.3.6.1.4.1.272.4.5.4.1.11 |
ipExtRtTosMaskThis object describes together with ipExtRtTos the
range of the Type of Service field (TOS) in the IP-header
of the IP-datagrams belonging to the set. A TOS value is
considered within the range, when the following equation
is valid:
(tos & ipExtRtTosMask) == (ipExtRtTos & ipExtRtTosMask)
If both objects are set to 0 the TOS value of the datagrams
in the set is not specified and can take any value.rw INTEGER .1.3.6.1.4.1.272.4.5.4.1.12 |
ipExtRtDstIfModeThis object describes different behavior depending on the
ifOperStatus of the destination interface:
dialup-wait:
The route matches, when the ifOperStatus of the
destination interface is either up or dormant.
If the status is dormant, the ifAdminStatus is
set to dialup to bring the interface to the up
state. The datagram will wait until the ifOperStatus
reaches the up state.
For all other states, the routing tables will be
searched for a different matching entry.
dialup-continue:
The route matches, if the ifOperStatus of the
destination interface is up. For all other states,
the routing tables are searched for different matching
entry. However, if the ifOperStatus was dormant,
the ifAdminStatus will be set to dialup to bring
the interface to the up state.
This setting can be used to establish a better
path for a specific service and to use an existing
path for that service as long as the better path
could not be established.
up-only:
The route matches, if the ifOperStatus of the
destination interface is up. For all other states,
the routing tables are searched for different matching
entry.
always:
The route matches independantly of the ifOperStatus
of the destination interface. If it is up, the
interface is used. If the state is dormant,
ifAdminStatus is set to dialup to bring the interface
in the up state. For all other states, the destination
is considered unreachable.rw Enumeration .1.3.6.1.4.1.272.4.5.4.1.13 |
ipExtRtDstIfIndexThis object specifies the destination interface for the
IP-datagrams belonging to the set. If the value of this
object is set to 0, the datagrams of the set are discarded
and an ICMP destination unreachable datagram is sent
back to the originator.rw INTEGER .1.3.6.1.4.1.272.4.5.4.1.14 |
ipExtRtNextHopThis object is used on point-to-multipoint interfaces
with indirect routes (see ipExrRtType) to specify
the IP-address of the gateway on the network, where
the datagram should be routed to.rw IpAddress .1.3.6.1.4.1.272.4.5.4.1.15 |
ipExtRtTypeThis object specifies, on point-to-multipoint interface
wether the datagram shall be sent to the destination
IP address in the IP datagram header (direct) or
to a gateway (indirect). In the later case, the IP-addres
of the gateway is specified by ipExtRtNextHop.
If this object is set to other, the entry is not
used for routing.
The complete entry can also be deleted, by setting this
object to invalid.rw Enumeration .1.3.6.1.4.1.272.4.5.4.1.16 |
ipExtRtMetric1This object is used to specify an order on the entries
in the ipExtRtTable. If a datagram is matching multiple
entries, the entry with the lowest value of ipExtRtMetric1
is choosen. The decision is undefined, when even after
interpreting the metric, there are still multiple entries
matching the IP-datagram.rw INTEGER .1.3.6.1.4.1.272.4.5.4.1.17 |
ipExtRtMetric2Undefined yet; for further extensionrw INTEGER .1.3.6.1.4.1.272.4.5.4.1.18 |
ipExtRtMetric3Undefined yet; for further extensionrw INTEGER .1.3.6.1.4.1.272.4.5.4.1.19 |
ipExtRtMetric4Undefined yet; for further extensionrw INTEGER .1.3.6.1.4.1.272.4.5.4.1.20 |
ipExtRtMetric5Undefined yet; for further extensionrw INTEGER .1.3.6.1.4.1.272.4.5.4.1.21 |
ipExtRtProtoThis object describes, how the route has been gained.
This will normaly be netmgmt, because there is currently
no routing protocol, that is able to handle extended routes.rw Enumeration .1.3.6.1.4.1.272.4.5.4.1.22 |
ipExtRtAgeThis object specifies the age of the route.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.272.4.5.4.1.23 |
ipNatTableIf NAT is switched on for an interface, this table contains
an entry for each session running over the interface. Table
entries are creates by the system whenever a valid session
is established. A session may be either a tcp connection,
a udp connection or an icmp connection with icmp-echo messages
(ping). A valid session is either an outgoing session or
an incoming session specified in the ipNatPresetTable.
Everything behind an interface with NAT enabled is called
outside. The BRICK itself and all networks connected
to it via interfaces without NAT are called inside.
Table entries are removed after timeout. This timeout
is
specified by ipExtIfNatOtherTimeout for UDP
and ICMP sessions.
specified by ipExtIfTcpTimeout for TCP sessions
16 seconds for closed TCP-sessions (FIN has been
received and acknowledged in both directions. SEQUENCE OF IpNatEntry .1.3.6.1.4.1.272.4.5.5 |
ipNatEntry IpNatEntry .1.3.6.1.4.1.272.4.5.5.1 |
ipNatIfIndexThis object specifies the interface, for which the session
is monitored.ro INTEGER .1.3.6.1.4.1.272.4.5.5.1.1 |
ipNatProtocolThis object specifies the protocol, the session is using.
The value icmp specifies an icmp-echo (ping) session. ICMP
error messages are processed by the appropriate tcp or
udp session.ro Enumeration .1.3.6.1.4.1.272.4.5.5.1.2 |
ipNatIntAddrThis object specifies the internal local IP Address used for
the session. The internal address is only visible to
inside networks and is translated to the external address,
when a packet is being sent outside.ro IpAddress .1.3.6.1.4.1.272.4.5.5.1.3 |
ipNatIntPortThis object specifies the internal local portnumber used for
the session. The internal portnumber is only visible to
inside networks and is translated to the external portnumber
whenever a packet is being sent outside.ro INTEGER .1.3.6.1.4.1.272.4.5.5.1.4 |
ipNatExtAddrThis object specifies the external local address used for
the session. This address is visible outside only and
will be translated to the internal address, whenever
a packet is received from outside.ro IpAddress .1.3.6.1.4.1.272.4.5.5.1.5 |
ipNatExtPortThis object specifies the external local portnumber used for
the session. This address is visible outside only and is
translated to the internal portnumber, whenever a packet
is received from outside.ro INTEGER .1.3.6.1.4.1.272.4.5.5.1.6 |
ipNatRemoteAddrThis object specifies the remote IP-address used for the
session. This is an outside address. However, it is visible
to outside networks and also to inside networks.ro IpAddress .1.3.6.1.4.1.272.4.5.5.1.7 |
ipNatRemotePortThis object specifies the remote portnumber used for the
session. This is an outside portnumber. However, it is visible
to outside networks and also to inside networks.ro INTEGER .1.3.6.1.4.1.272.4.5.5.1.8 |
ipNatDirectionThis object specifies, whether the session is incoming
(from outside to inside) or outgoing (from inside to
outside).ro Enumeration .1.3.6.1.4.1.272.4.5.5.1.9 |
ipNatAgeThis object specifies how long no packet has been
transferred for the session and is used internally
for timeout purposes.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.272.4.5.5.1.10 |
ipNatPresetTableThis table specifies the IP addresses and port numbers
for sessions requested from outside. If this table is
empty and NAT is enabled, only packets for sessions
initiated from inside are forwarded.
The IP address and the port number of the internal server
can be specified individually for each combination of
- protocol (udp/tcp/icmp)
- initiating hosts IP address (RemoteAddr, RemoteMask)
- called hosts IP address (ExtAddr, ExtMask)
- called port number (ExtPort, ExtPortRange)
Entries in the table are created and removed manually
by network management. SEQUENCE OF IpNatPresetEntry .1.3.6.1.4.1.272.4.5.6 |
ipNatPresetEntry IpNatPresetEntry .1.3.6.1.4.1.272.4.5.6.1 |
ipNatPrIfIndexThis object specifies the interface index, for which the
table entry shall be valid. If set to 0, the entry will
be valid for all interfaces configured to use NAT.rw INTEGER .1.3.6.1.4.1.272.4.5.6.1.1 |
ipNatPrProtocolThis object specifies the protocol, for which the table
entry shall be valid.rw Enumeration .1.3.6.1.4.1.272.4.5.6.1.2 |
ipNatPrRemoteAddrThis object specifies together with ipNatPrRemoteMask the
the set of IP addresses of remote hosts initiating the
connection. The table entry will be valid for an incoming
call, when the IP adress of the remote host initiating
the connection lies in the range specified by both objects.
If both objects are set to 0.0.0.0, the table entry will
be valid for any remote host.rw IpAddress .1.3.6.1.4.1.272.4.5.6.1.3 |
ipNatPrRemoteMaskThis object specifies together with ipNatPrRemoteAddr the
the set of IP addresses of remote hosts initiating the
connection. The table entry will be valid for an incoming
call, when the IP adress of the remote host initiating
the connection lies in the range specified by both objects.
If both objects are set to 0.0.0.0, the table entry will
be valid for any remote host.rw IpAddress .1.3.6.1.4.1.272.4.5.6.1.4 |
ipNatPrExtAddrThis object specifies together with ipNatPrExtMask the
the set of called IP addresses, for which the table entry
shall be valid. The entry is valid, if the called IP address
of an incoming calls setup packet lies in the range specified
by both objects.
If both objects are set to 0.0.0.0, the table entry will
be valid for any called IP address.rw IpAddress .1.3.6.1.4.1.272.4.5.6.1.5 |
ipNatPrExtMaskThis object specifies together with ipNatPrExtAddr the
the set of called IP addresses, for which the table entry
shall be valid. The entry is valid, if the called IP address
of an incoming calls setup packet lies in the range specified
by both objects.
If both objects are set to 0.0.0.0, the table entry will
be valid for any called IP address.rw IpAddress .1.3.6.1.4.1.272.4.5.6.1.6 |
ipNatPrExtPortThis object specifies together with ipNatPrExtPortRange the
range of portnumbers for incoming call, for which the table
entry shall be valid. If both objects are set to -1, the
entry is valid for all portnumbers. If ipNatPrPortRange
is set to -1, the entry is only valid, when the called
portnumber of an incoming call is equal to ipNatPrExtPort.
Otherwise, the entry is valid, if the called portnumber
lies in the range ExtPort .. ExtPortRange.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.6.1.7 |
ipNatPrExtPortRangeThis object specifies together with ipNatPrExtPort the
range of portnumbers for incoming call, for which the table
entry shall be valid. If both objects are set to -1, the
entry is valid for all portnumbers. If ipNatPrPortRange
is set to -1, the entry is only valid, when the called
portnumber of an incoming call is equal to ipNatPrExtPort.
Otherwise, the entry is valid, if the called portnumber
lies in the range ExtPort .. ExtPortRange.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.6.1.8 |
ipNatPrIntAddrThis object specifies the internal target hosts IP address
for incoming calls matching the table entry.
An incoming call matching this entry will be routed
to the internal server specified by this object.
If this object is set to 0.0.0.0 the target host will be
the original target host in the incoming calls setup
packet. No translation of the IP-addresses take place
in this case.rw IpAddress .1.3.6.1.4.1.272.4.5.6.1.9 |
ipNatPrIntPortThis object specifies the internal target hosts port-number
for incoming calls matching the table entry. If this
object is set to -1, the target portnumber will be
taken from the original incoming calls setup packet.
No translation of the portnumber will take place in this
case. If the set of portnumbers for this table entry is
a range instead of a single portnumber, this object will
specify the base of the target range of portnumbers. The
internal portnumber will be constructed as follows:
new-target-port := old-target-port
- ipNatPrExtPort
+ ipNatPrIntPortrw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.6.1.10 |
ipSessionTable SEQUENCE OF IpSessionEntry .1.3.6.1.4.1.272.4.5.7 |
ipSessionEntry IpSessionEntry .1.3.6.1.4.1.272.4.5.7.1 |
ipSessionSrcAddrro IpAddress .1.3.6.1.4.1.272.4.5.7.1.1 |
ipSessionSrcPortro INTEGER .1.3.6.1.4.1.272.4.5.7.1.2 |
ipSessionDstAddrro IpAddress .1.3.6.1.4.1.272.4.5.7.1.3 |
ipSessionDstPortro INTEGER .1.3.6.1.4.1.272.4.5.7.1.4 |
ipSessionOutPktsro Counter .1.3.6.1.4.1.272.4.5.7.1.5 |
ipSessionOutOctetsro Counter .1.3.6.1.4.1.272.4.5.7.1.6 |
ipSessionInPktsro Counter .1.3.6.1.4.1.272.4.5.7.1.7 |
ipSessionInOctetsro Counter .1.3.6.1.4.1.272.4.5.7.1.8 |
ipSessionProtocolro Enumeration .1.3.6.1.4.1.272.4.5.7.1.9 |
ipSessionAgero TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.272.4.5.7.1.10 |
ipSessionIdlero TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.272.4.5.7.1.11 |
ipSessionSrcIfIndexro INTEGER .1.3.6.1.4.1.272.4.5.7.1.12 |
ipSessionDstIfIndexro INTEGER .1.3.6.1.4.1.272.4.5.7.1.13 |
ipImportTableThis table specifies how routes from one routing protocol
are imported into another routing protocol. The dummy
protocol default-route allows the generation of a default
route for the routing domain. Not all combinations of
source and destination protocols might be valid or
implemented. SEQUENCE OF IpImportEntry .1.3.6.1.4.1.272.4.5.12 |
ipImportEntry IpImportEntry .1.3.6.1.4.1.272.4.5.12.1 |
ipImportSrcProtoThis object describes the protocol that generated the route
and inserted it into the routing table.rw Enumeration .1.3.6.1.4.1.272.4.5.12.1.1 |
ipImportDstProtoThis object describes the destination protocol into that the
routes should be imported.rw Enumeration .1.3.6.1.4.1.272.4.5.12.1.2 |
ipImportMetric1This object defines the metric in the context of the
destination protocol the imported routes should get.
If set to -1 these routes get a protocol specific
default metric.rw INTEGER .1.3.6.1.4.1.272.4.5.12.1.3 |
ipImportTypeThis object might define protocol specific properties of
the imported routes in the context of the destination
protocol.rw INTEGER .1.3.6.1.4.1.272.4.5.12.1.4 |
ipImportAddrThis object specifies together with ipImportMask the range
of IP addresses for which the table entry should be valid.
The entry is valid if the destination IP address of the
route lies in the range specified by both objects.
If both objects are set to 0.0.0.0, the table entry will
be valid for destination.rw IpAddress .1.3.6.1.4.1.272.4.5.12.1.5 |
ipImportMaskThis object specifies together with ipImportAddr the range
of IP addresses for which the table entry should be valid.
The entry is valid if the destination IP address of the
route lies in the range specified by both objects.
If both objects are set to 0.0.0.0, the table entry will
be valid for destination.rw IpAddress .1.3.6.1.4.1.272.4.5.12.1.6 |
ipImportEffectThis object defines the effect this row should have. If set
to import, the importation from ipImportSrcProto to
ipImportDstProto takes place. If set to doNotImport the
importation is prevented.rw Enumeration .1.3.6.1.4.1.272.4.5.12.1.7 |
ipImportIfIndexThis object specifies the interface index of the interface
for which the entry should be valid. If set to 0 it will be
valid for all interfaces.rw INTEGER .1.3.6.1.4.1.272.4.5.12.1.8 |
ipPriorityTableThis table defines the order, in which routes from different
protocols are being used to determine the destination of an
ip packet. The table will contain an entry for each type
of routing protocol including STATIC and DIRECT routes.
A priority-value can be configured for each of those protocols
to get an order between the different protocols. The table
contains a fixed number of entries. Only the priority may be
configured. SEQUENCE OF IpPriorityEntry .1.3.6.1.4.1.272.4.5.13 |
ipPriorityEntry IpPriorityEntry .1.3.6.1.4.1.272.4.5.13.1 |
ipPriorityProtoThis object specifies the routig-protocol, for which the
entry is valid.ro Enumeration .1.3.6.1.4.1.272.4.5.13.1.1 |
ipPriorityValueThis object contains the priority-value for a specific routing
protocol. Low values mean high precedence.rw INTEGER .1.3.6.1.4.1.272.4.5.13.1.2 |
ipFilterTableThe ipFilterTable defines filters that describe subsets
of IP packets. The filter matches if all conditions defined
are true when comparing with the header of an IP packet. SEQUENCE OF IpFilterEntry .1.3.6.1.4.1.272.4.5.15 |
ipFilterEntry IpFilterEntry .1.3.6.1.4.1.272.4.5.15.1 |
ipFilterIndexThis object uniquely references this filter. The index
value is generated automatically.ro INTEGER .1.3.6.1.4.1.272.4.5.15.1.1 |
ipFilterDescrA textual string describing this filter.rw DisplayString .1.3.6.1.4.1.272.4.5.15.1.2 |
ipFilterProtocolThis object specifies the value of the protocol field in
the ip header for all IP-datagrams belonging to the set.
If this object is set to dont-verify, the value of the
protocol field is not specified and can take any value.rw Enumeration .1.3.6.1.4.1.272.4.5.15.1.3 |
ipFilterSrcAddrThis object specifies together with ipFilterSrcMask
the set of IP addresses of datagrams that belong to the
subset defined by this entry. If both objects are set to
0.0.0.0 the source-addresses for the datagrams in the set
is not specified and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.15.1.4 |
ipFilterSrcMaskThis object specifies together with ipFilterSrcAddr
the set of IP addresses of datagrams that belong to the
subset defined by this entry. If both objects are set to
0.0.0.0 the source-addresses for the datagrams in the set
is not specified and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.15.1.5 |
ipFilterSrcPortThis object describes together with ipFilterSrcPortRange the
range of source portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the source
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.15.1.6 |
ipFilterSrcPortRangeThis object describes together with ipFilterDstPort the
range of source portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the source
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.15.1.7 |
ipFilterDstAddrThis object describes together with ipFilterDstMask the
range of the target-addresses of the IP-datagrams belonging
to the set. If both objects are set to 0.0.0.0 the target-
addresses for the datagrams in the set is not specified
and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.15.1.8 |
ipFilterDstMaskThis object describes together with ipFilterDstAddr the
range of the target-addresses of the IP-datagrams belonging
to the set. If both objects are set to 0.0.0.0 the target-
addresses for the datagrams in the set is not specified
and can take any value.rw IpAddress .1.3.6.1.4.1.272.4.5.15.1.9 |
ipFilterDstPortThis object describes together with ipFilterDstPortRange the
range of target-portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the target
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.15.1.10 |
ipFilterDstPortRangeThis object describes together with ipFilterDstPort the
range of target-portnumbers of the IP-datagrams belonging to
the set. All portnumbers between and including the two
objects are within the range.
If both objects are the to -1, the value of the target
portnumber is not specified and can take any value.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.15.1.11 |
ipFilterTcpConnStateThis object describes the state of the TCP connection
associated with the packets belonging to the set.
If this object is set to established, the value of the TCP
flags of incoming packets is checked. Packets with flags
that initiate TCP connections are excluded from the set.
If this object is set to dont-verify, the TCP flags are
not checked and can be any value.rw Enumeration .1.3.6.1.4.1.272.4.5.15.1.12 |
ipFilterIcmpTypeThis object describes the ICMP type of the packets belonging
to the set. If this object is set to dont-verify, the value
of the ICMP type field is not specified and can take any
value.rw Enumeration .1.3.6.1.4.1.272.4.5.15.1.13 |
ipFilterTosThis object describes together with ipFilterTosMask the
range of the Type of Service field (TOS) in the IP-header
of the IP-datagrams belonging to the set. A TOS value is
considered within the range, when the following equation
is valid:
(tos & ipFilterTosMask) == (ipFilterTos & ipFilterTosMask)
If both objects are set to 0 the TOS value of the datagrams
in the set is not specified and can take any value.rw INTEGER .1.3.6.1.4.1.272.4.5.15.1.14 |
ipFilterTosMaskThis object describes together with ipFilterTos the
range of the Type of Service field (TOS) in the IP-header
of the IP-datagrams belonging to the set. A TOS value is
considered within the range, when the following equation
is valid:
(tos & ipFilterTosMask) == (ipFilterTos & ipFilterTosMask)
If both objects are set to 0 the TOS value of the datagrams
in the set is not specified and can take any value.rw INTEGER .1.3.6.1.4.1.272.4.5.15.1.15 |
ipRuleTableThe ipRuleTable defines access rules for checking incoming
IP packets. The rules are processed in order, i.e. each rule
has a link to the next rule. The set of rules is processed
until a match occurs, that means the rule's associated filter
matches and the specified action is performed (either accept
or deny a packet). The last rule is implicitly a deny rule.
The set of rules to be processed can be defined for each
interface SEQUENCE OF IpRuleEntry .1.3.6.1.4.1.272.4.5.16 |
ipRuleEntry IpRuleEntry .1.3.6.1.4.1.272.4.5.16.1 |
ipRuleIndexUnique rule index.ro INTEGER .1.3.6.1.4.1.272.4.5.16.1.1 |
ipRuleFilterIndexReferences the rule's associated filter.rw INTEGER .1.3.6.1.4.1.272.4.5.16.1.2 |
ipRuleActionThis object specifies the action to be performed if the
rule's associated filter matches. If set to ignore the
filter is not consulted and the next rule is processed
immediately.rw Enumeration .1.3.6.1.4.1.272.4.5.16.1.3 |
ipRuleNextRuleIndexSpecifies the next rule to be processed if the rule's
associated filter does not match. The value 0 is used
to mark the end of the rule set.rw INTEGER .1.3.6.1.4.1.272.4.5.16.1.4 |
ipNatOutTableThis table specifies the IP address translation for
outgoing sessions. If no matching entry is found the
IP address is set to the IP address defined on the
interface configured for NAT. If a matching entry is
found, the source IP address of outgoing IP packets
is set to the value of ipNatOutExtAddr.
This table is only used if the outgoing address
translation is activated (ipExtIfNatOutXlat).
Entries in the table are created and removed manually
by network management. SEQUENCE OF IpNatOutEntry .1.3.6.1.4.1.272.4.5.18 |
ipNatOutEntry IpNatOutEntry .1.3.6.1.4.1.272.4.5.18.1 |
ipNatOutIfIndexThis object specifies the interface index, for which the
table entry shall be valid. If set to 0, the entry will
be valid for all interfaces configured to use NAT.rw INTEGER .1.3.6.1.4.1.272.4.5.18.1.1 |
ipNatOutProtocolThis object specifies the protocol, for which the table
entry shall be valid.rw Enumeration .1.3.6.1.4.1.272.4.5.18.1.2 |
ipNatOutRemoteAddrThis object specifies together with ipNatOutRemoteMask the
set of target IP addresses for which the table entry is
valid. If both objects are set to 0.0.0.0, the table entry
will be valid for any target IP address.rw IpAddress .1.3.6.1.4.1.272.4.5.18.1.3 |
ipNatOutRemoteMaskThis object specifies together with ipNatOutRemoteAddr the
set of target IP addresses for which the table entry is
valid. If both objects are set to 0.0.0.0, the table entry
will be valid for any target IP address.rw IpAddress .1.3.6.1.4.1.272.4.5.18.1.4 |
ipNatOutExtAddrThis object specifies the external IP address to which
the internal IP address is mapped.rw IpAddress .1.3.6.1.4.1.272.4.5.18.1.5 |
ipNatOutRemotePortThis object specifies together with ipNatOutRemotePortRange
the range of portnumbers for outgoing calls, for which the
table entry shall be valid. If both objects are set to -1, the
entry is valid for all portnumbers. If ipNatOutPortRange
is set to -1, the entry is only valid, when the portnumber
of an outgoing call is equal to ipNatOutRemotePort.
Otherwise, the entry is valid, if the called portnumber
lies in the range RemotePort .. RemotePortRange.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.18.1.6 |
ipNatOutRemotePortRangeThis object specifies together with ipNatOutRemotePort
the range of portnumbers for outgoing calls, for which the
table entry shall be valid. If both objects are set to -1, the
entry is valid for all portnumbers. If ipNatOutPortRange
is set to -1, the entry is only valid, when the portnumber
of an outgoing call is equal to ipNatOutRemotePort.
Otherwise, the entry is valid, if the called portnumber
lies in the range RemotePort .. RemotePortRange.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.18.1.7 |
ipNatOutIntAddrThis object specifies together with ipNatOutIntMask
the internal hosts IP address for outgoing calls
matching the table entry. If both objects are set to
0.0.0.0, the table entry will be valid for any source
IP address.rw IpAddress .1.3.6.1.4.1.272.4.5.18.1.8 |
ipNatOutIntMaskThis object specifies together with ipNatOutIntAddr
the internal hosts IP address for outgoing calls
matching the table entry. If both objects are set to
0.0.0.0, the table entry will be valid for any source
IP address.rw IpAddress .1.3.6.1.4.1.272.4.5.18.1.9 |
ipNatOutIntPortThis object specifies the internal source port for which the
table entry shall be valid. If this object is set to -1,
any internal source port matches this entry.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.18.1.10 |
ipNatOutExtPortThis object may be used to specify a fixed external source
port to which the internal source port is mapped.
If this object is set to -1, the port is mapped to the next
free source port available.rw INTEGER (-1..65535) .1.3.6.1.4.1.272.4.5.18.1.11 |
ipHostsAliveTableThis table specifies the watched IP addresses.
Entries in the table are created and removed manually
by network management. SEQUENCE OF IpHostsAliveEntry .1.3.6.1.4.1.272.4.5.19 |
ipHostsAliveEntry IpHostsAliveEntry .1.3.6.1.4.1.272.4.5.19.1 |
ipHostsAliveGroupThe group of the watched IP-Addressesrw INTEGER .1.3.6.1.4.1.272.4.5.19.1.1 |
ipHostsAliveIPAddressThe watched IP-Addressrw IpAddress .1.3.6.1.4.1.272.4.5.19.1.2 |
ipHostsAliveStateThe State of the watched IP-Addressro Enumeration .1.3.6.1.4.1.272.4.5.19.1.3 |
ipHostsAliveIntervalThis is the timeinterval for state verificationrw INTEGER .1.3.6.1.4.1.272.4.5.19.1.4 |
ipHostsAliveDownActionThis action must be perform, if the hosts do not answerrw Enumeration .1.3.6.1.4.1.272.4.5.19.1.5 |
ipHostsAliveFirstIfIndexThe first ifcrw INTEGER .1.3.6.1.4.1.272.4.5.19.1.6 |
ipHostsAliveRangeThe range of all ifcsrw INTEGER .1.3.6.1.4.1.272.4.5.19.1.7 |
ipBodRuleTableThe ipBodRuleTable defines access rules for checking incoming
IP packets. The rules are processed in order, i.e. each rule
has a link to the next rule. The set of rules is processed
until a match occurs, that means the rule's associated filter
matches and the specified action is performed (either request
or deny additional bandwidth). The last rule is implicitly a
deny rule. The set of rules to be processed can be defined
for each interface. SEQUENCE OF IpBodRuleEntry .1.3.6.1.4.1.272.4.5.21 |
ipBodRuleEntry IpBodRuleEntry .1.3.6.1.4.1.272.4.5.21.1 |
ipBodRuleIndexUnique rule index.ro INTEGER .1.3.6.1.4.1.272.4.5.21.1.1 |
ipBodRuleFilterIndexReferences the rule's associated filter.rw INTEGER .1.3.6.1.4.1.272.4.5.21.1.2 |
ipBodRuleActionThis object specifies the action to be performed if the
rule's associated filter matches. If set to ignore the
filter is not consulted and the next rule is processed
immediately.rw Enumeration .1.3.6.1.4.1.272.4.5.21.1.3 |
ipBodRuleDirectionThis object specifies the direction of the packets for
which the rule is processed.rw Enumeration .1.3.6.1.4.1.272.4.5.21.1.4 |
ipBodRuleChannelsThe number of B-channels to invoke if the rule's
associated filter matches.rw INTEGER .1.3.6.1.4.1.272.4.5.21.1.5 |
ipBodRuleNextRuleIndexSpecifies the next rule to be processed if the rule's
associated filter does not match. The value 0 is used
to mark the end of the rule set.rw INTEGER .1.3.6.1.4.1.272.4.5.21.1.6 |
ipBodRuleIdleTimeSpecifies the time in seconds the interface-specific
shorthold interval (see biboPPPTable) is extended if the
rule's associated filter matches. When set to zero this
setting is ignored. When set to -1 matching packets are
sent piggyback, they are not considered for shorthold mode.rw INTEGER (-1..3600) .1.3.6.1.4.1.272.4.5.21.1.7 |
ipQoSTableThe ipQosTable defines the classifier rules that are applied
to IP traffic arriving this interface in a particular
direction. The rules are processed in order, i.e. each rule
has a link to the next rule. The set of rules is processed
until a match occurs, that means the rule's associated filter
matches and the specified action is performed (set the IP
headers TOS field, specify a service class for QoS). The
set of these rules to be processed can be defined for each
interface. SEQUENCE OF IpQoSEntry .1.3.6.1.4.1.272.4.5.22 |
ipQoSEntry IpQoSEntry .1.3.6.1.4.1.272.4.5.22.1 |
ipQoSIndexUnique rule index.ro INTEGER .1.3.6.1.4.1.272.4.5.22.1.1 |
ipQoSFilterIndexReferences the associated filter (see IpFilterTable).rw INTEGER .1.3.6.1.4.1.272.4.5.22.1.2 |
ipQoSNextRuleIndexSpecifies the next classifier rule to be processed if the
rule's associated filter does not match. The value 0 is used
to mark the end of the rule set.rw INTEGER .1.3.6.1.4.1.272.4.5.22.1.3 |
ipQoSActionThis object specifies the action to be performed if the
associated filter matches. If set to ignore the filter is
not consulted and the next rule is processed immediately,
possible values:
classify(1) = filter matches, set TOS & classify packet
classify-if-not(2) = classify if filter doesn't match
disabled(3) = ignore rule and skip to next rule
delete(4) = delete the entry from the table.rw Enumeration .1.3.6.1.4.1.272.4.5.22.1.4 |
ipQoSTosValue for TOS field inside IP header to be set.rw INTEGER .1.3.6.1.4.1.272.4.5.22.1.5 |
ipQoSTosSetRateMaximum amount of packets per second that should be TOS
changed.rw INTEGER .1.3.6.1.4.1.272.4.5.22.1.7 |
ipQoSTosSetBurstMaximum amount of packets per second additional to the
ipQosSetRate that could be TOS changed.rw INTEGER .1.3.6.1.4.1.272.4.5.22.1.8 |
ipQoSServiceClassThis object specifies together with ipQoSClassId the class
of service used for the congestion management, priorization
and traffic shapping. If set to high-priority(2) (high
priority service class) the related traffic will be always
handled first and ipQoSClassId is ignored.rw Enumeration .1.3.6.1.4.1.272.4.5.22.1.11 |
ipQoSClassIdThis object specifies together with ipQoSServiceClass
(normal(1) only) the class of service used for congestion
avoidance, congestion management, priorization and traffic
shapping. Note that this ID is not used to give a nominal
priority to the related IP traffic.rw INTEGER .1.3.6.1.4.1.272.4.5.22.1.12 |
ipQoSDirectionThis object specifies the direction for witch this classifier
rule applies on this interface, possible values:
outgoing(1) = used for outgoing packets only
incoming(2) = used for incoming packets only
both(3) = used for both directions.rw Enumeration .1.3.6.1.4.1.272.4.5.22.1.13 |