BIANCA-BOX-ISDN-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for BIANCA-BOX-ISDN-MIB.
162
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
162 total| Object Name |
|---|
org OBJECT IDENTIFIER .1.3 |
dod OBJECT IDENTIFIER .1.3.6 |
internet OBJECT IDENTIFIER .1.3.6.1 |
private OBJECT IDENTIFIER .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
bintec OBJECT IDENTIFIER .1.3.6.1.4.1.272 |
bibo OBJECT IDENTIFIER .1.3.6.1.4.1.272.4 |
isdn OBJECT IDENTIFIER .1.3.6.1.4.1.272.4.2 |
isdnIfTableThe isdnIfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected ISDN interface (BRI or PRI). Entries can only be added or deleted by the system. Creating entries: Entries are created by the system only when a new BRI or PRI module is installed. Deleting entries: Entries are removed by the system after the appropriate BRI or PRI module is removed. SEQUENCE OF IsdnIfEntry .1.3.6.1.4.1.272.4.2.1 |
isdnIfEntry IsdnIfEntry .1.3.6.1.4.1.272.4.2.1.1 |
isdnIfIndexUnique index of the basic or primary rate interface.ro INTEGER .1.3.6.1.4.1.272.4.2.1.1.1 |
isdnIfDescriptionTextual description of the basic rate interface including its slot and number (e.g. bri2-0 means slot 2, unit 0).ro DisplayString .1.3.6.1.4.1.272.4.2.1.1.2 |
isdnIfLayer1StateThe ISDN physical layer state according to I.430 f1(1) = inactive; f2(2) = sensing; f3(3) = deactivated; f4(4) = awaiting signal; f5(5) = identifying input; f6(6) = synchronized; f7(7) = activated; f8(8) = lost framing; g1(9) = deactive; g2(10) = pending activation; g3(11) = active; g4(12) = pending deactivationro Enumeration .1.3.6.1.4.1.272.4.2.1.1.3 |
isdnIfBchannelControlB-channels are controlled by a call control protocol in the D-channel. Otherwise they may be used as permanent links.ro Enumeration .1.3.6.1.4.1.272.4.2.1.1.4 |
isdnIfActivationRequestWhen this object is set to 'activate' the BRICK will start an activation sequence of ISDN-Layer1 of the basic rate interface.rw Enumeration .1.3.6.1.4.1.272.4.2.1.1.5 |
isdnIfModeSpecifies the mode of the interface. TE or NT Mode will be set for ISDN interfaces without PABX control. For PRI both NT (network termination) and TE (terminal equipment) modes are supported.rw Enumeration .1.3.6.1.4.1.272.4.2.1.1.6 |
isdnIfTimerT3Value of Timer T3 in milliseconds.T3 is started whenever ISDNLayer-1 is activated (i.e. Activation Request is started).rw INTEGER .1.3.6.1.4.1.272.4.2.1.1.7 |
isdnIfUsePowerDetectorUse the PS1 Power Detector to control the layer 1 automaton.This object is only valid for basic rate interfaces.rw Enumeration .1.3.6.1.4.1.272.4.2.1.1.8 |
isdnIfNumberOfChannelsNumber of Channels including the D channel, that are available on this ISDN Interface (3 = BRI, 31 = PRI).ro INTEGER .1.3.6.1.4.1.272.4.2.1.1.9 |
isdnIfTimeoutsNumber of timeouts of T3 during lifetime of the system.ro Counter .1.3.6.1.4.1.272.4.2.1.1.10 |
isdnIfActivatesNumber of successful activation cycles during lifetime of the system.ro Counter .1.3.6.1.4.1.272.4.2.1.1.11 |
isdnIfDeactivatesNumber of deactivations during lifetime of the system.ro Counter .1.3.6.1.4.1.272.4.2.1.1.12 |
isdnIfAutoconfigStateStart auto configuration on this ISDN Interface. Auto configuration is a mechanism to automatically detect the attributes of an ISDN interface. This can be done at boot time (if isdnIfAutoConfig is set to 'on') or by manually setting this field to 'start'. Refer to Chapter 3 on Features and Methods.rw Enumeration .1.3.6.1.4.1.272.4.2.1.1.13 |
isdnIfAutoconfigStart Autoconfiguration on this ISDN interface at bootup.rw Enumeration .1.3.6.1.4.1.272.4.2.1.1.14 |
isdnIfSlipsSlip conditions detected since startup. Flags that the frequency of receive clock is different than frequency of internal system clock.ro Counter .1.3.6.1.4.1.272.4.2.1.1.21 |
isdnChTableThe isdnChTable contains information for each physical B or D channel on the system. The entries contain information regarding the configuration of the channel and various statistical data for active connections. Only the system can add entries to this table. Creating entries: Entries are created by the system when a new interface appears in the isdnIfTable; when a new BRI or PRI module is installed. Deleting entries: Are not possible. SEQUENCE OF IsdnChEntry .1.3.6.1.4.1.272.4.2.2 |
isdnChEntry IsdnChEntry .1.3.6.1.4.1.272.4.2.2.1 |
isdnChIsdnIfIndexUnique index of an Interface.ro INTEGER .1.3.6.1.4.1.272.4.2.2.1.1 |
isdnChNumberThe channel number. 0 is D-channel, 1..2 are the B- channels of a BRI module, and 1..31 are the B-channels of a PRI module.ro INTEGER .1.3.6.1.4.1.272.4.2.2.1.2 |
isdnChStateStatus of the Channel controlled either by the call control protocol or the physical state of the interface.ro Enumeration .1.3.6.1.4.1.272.4.2.2.1.3 |
isdnChTypeType of Channel.Setting this object to one of the leased values creates a new entry in the ifTable.rw Enumeration .1.3.6.1.4.1.272.4.2.2.1.4 |
isdnChBundleIndex of the bundle to aggregate multiple Channels to one interface. Not valid in dialup mode.rw INTEGER .1.3.6.1.4.1.272.4.2.2.1.5 |
isdnChThroughputThroughput of the channel in bits/second (64000 for B-channels, 16000 for BRI D-Channels.ro INTEGER .1.3.6.1.4.1.272.4.2.2.1.6 |
isdnChReceivedPacketsCount of received valid HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.2.1.7 |
isdnChReceivedOctetsCount of received valid HDLC bytes.ro Counter .1.3.6.1.4.1.272.4.2.2.1.8 |
isdnChReceivedErrorsCount of received valid errors (can be detected by HDLC-Checksum-Errors).ro Counter .1.3.6.1.4.1.272.4.2.2.1.9 |
isdnChTransmitPacketsCount of received valid HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.2.1.10 |
isdnChTransmitOctetsCount of received valid HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.2.1.11 |
isdnChTransmitErrorsCount of transmitted valid HDLC errors. Can occur when the transmitter can not be reloaded fast enough when transmitting large packets. This should only happen when the system is over encumbered.ro Counter .1.3.6.1.4.1.272.4.2.2.1.12 |
isdnStkTableThe isdnStkTable contains information for each ISDN protocol stack currently configured on the system. Entries are normally created by the system at boot time, during the auto configuration process, but can also be added manually. Creating entries: Entries are created by the system during the ISDN auto configuration procedure at boot time (see Chapter 3). Entries can also be created by assigning a value to the Number and isdnIfNumber objects. Deleting entries: Entries can be removed by assigning the value 'delete' to the ProtocolProfile object. SEQUENCE OF IsdnStkEntry .1.3.6.1.4.1.272.4.2.3 |
isdnStkEntry IsdnStkEntry .1.3.6.1.4.1.272.4.2.3.1 |
isdnStkNumberUnique number of an ISDN stack (0..n). This number can be used in the isdnDispatchTable.rw INTEGER .1.3.6.1.4.1.272.4.2.3.1.1 |
isdnStkIsdnIfIndexThe index of the ISDN interface. The isdnIfTable lists all available ISDN interfaces.rw INTEGER .1.3.6.1.4.1.272.4.2.3.1.3 |
isdnStkProtocolProfileThe protocol for the D channel. Assigning `delete' to this object has the effect of removing the entry from this table.rw Enumeration .1.3.6.1.4.1.272.4.2.3.1.4 |
isdnStkConfigurationrw Enumeration .1.3.6.1.4.1.272.4.2.3.1.5 |
isdnStkSPIDThe service profile identifier; only required for the national ISDN1 protocol in North America.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.3.1.6 |
isdnStkTeiProcThe Tei procedure used. Note that for point-to-point configurations this object should be set to fixed(2).rw Enumeration .1.3.6.1.4.1.272.4.2.3.1.7 |
isdnStkTeiValueThe Tei value. Note that for point-to-point configurations this object should be 0.rw INTEGER (-1..126) .1.3.6.1.4.1.272.4.2.3.1.8 |
isdnStkClearAllCallsSetting this value to clear(2) will force all current connections on this stack to terminate.rw Enumeration .1.3.6.1.4.1.272.4.2.3.1.22 |
isdnStkStatusShows the status of this ISDN stack. If auto configuration was successful for this stack, this object will be loaded(1). If this stack is not loaded, ISDN calls are not possible.ro Enumeration .1.3.6.1.4.1.272.4.2.3.1.23 |
isdnStkLayer2StateShows the current state of Layer2. To allow ISDN connections, the state established(4) must be assigned.ro Enumeration .1.3.6.1.4.1.272.4.2.3.1.24 |
isdnStkBchannelsNumber of B channels that correspond to that stack.rw INTEGER .1.3.6.1.4.1.272.4.2.3.1.25 |
isdnStkDialOutPrefixPrefix for PABX dialout. This entry is added to a dialing number provided by the calling site via PPP negotiation (LCP Callback Option / PPP Bandwith Alllocation Protocol).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.3.1.26 |
isdnCallTableThe isdnCallTable displays all currently active ISDN calls (incoming and outgoing). Only the system can add or remove entries to this table. Creating entries: Entries are added when an outgoing call is made or when an incoming call is connected. Deleting entries: Entries are removed once the respective call is disconnected. SEQUENCE OF IsdnCallEntry .1.3.6.1.4.1.272.4.2.4 |
isdnCallEntry IsdnCallEntry .1.3.6.1.4.1.272.4.2.4.1 |
isdnCallStkNumberThe number of the ISDN-Stack, this call is going through. Refer to the isdnStkTable.ro INTEGER .1.3.6.1.4.1.272.4.2.4.1.1 |
isdnCallTypeThe direction of the call.ro Enumeration .1.3.6.1.4.1.272.4.2.4.1.2 |
isdnCallReferenceThe corresponding Call-Reference Value on the ISDN D-channel.ro INTEGER .1.3.6.1.4.1.272.4.2.4.1.3 |
isdnCallAgeThe age of the call. For outgoing calls, the time since the call began, or for incoming calls, the time since the call was received. The format is in hh:mm:ss.00.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.272.4.2.4.1.4 |
isdnCallStateThe state of the call.rw Enumeration .1.3.6.1.4.1.272.4.2.4.1.5 |
isdnCallIsdnIfIndexThe corresponding ISDN interface that is used for this call. Refer to the isdnIfTable.ro INTEGER .1.3.6.1.4.1.272.4.2.4.1.6 |
isdnCallChannelThe corresponding B-channel on this ISDN interface. Refer to the isdnIfTable.ro INTEGER .1.3.6.1.4.1.272.4.2.4.1.7 |
isdnCallDspItemThe item to or from which this call is connected. For any routing tasks (IP, IPX, X.25, bridging, ...) the ppp(1) item is used. For the isdnlogin program, login(2) is used. For CAPI 1.1 programs, the items eaz0(48) .. eaz9(57) are used.ro Enumeration .1.3.6.1.4.1.272.4.2.4.1.8 |
isdnCallRemoteNumberThe ISDN number that was called (for outgoing calls) or was calling (for incoming calls).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.4.1.9 |
isdnCallRemoteSubaddressThe subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnCallRemoteNumber.ro OCTET STRING .1.3.6.1.4.1.272.4.2.4.1.10 |
isdnCallLocalNumberThe calling party number that was sent (with the outgoing call) or was received (with incoming calls). Refer to the isdnStkTable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.4.1.11 |
isdnCallLocalSubaddressThe subaddress of the calling party number. See isdnCallRLocalNumber.ro OCTET STRING .1.3.6.1.4.1.272.4.2.4.1.12 |
isdnCallServiceIndicatorService indicator that was sent on the ISDN D-channel when the call was established.ro Enumeration .1.3.6.1.4.1.272.4.2.4.1.13 |
isdnCallAddInfoAdditional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol.ro INTEGER .1.3.6.1.4.1.272.4.2.4.1.14 |
isdnCallBCBearer Capability that was sent on the ISDN D-channel when the call was established.ro OCTET STRING .1.3.6.1.4.1.272.4.2.4.1.15 |
isdnCallLLCLow Layer Capability that was sent on the ISDN D-channel when the call was established.ro OCTET STRING .1.3.6.1.4.1.272.4.2.4.1.16 |
isdnCallHLCThe number of charging ticks received since this connection was established. Actual charges can be computed by multiplying this value with the unit price (e.g. .12 DM in Germany). If you aren't receiving charging information for outgoing calls, verify with your local ISDN provider to make sure this option is being provided/is available.ro OCTET STRING .1.3.6.1.4.1.272.4.2.4.1.17 |
isdnCallChargeThis object contains the charge for this call either as units or as 1/1000 of the respective currency. Which type of information is choosen, depends on the information provided by the ISDN service provide. See also ChargeInfo for textual information.ro INTEGER .1.3.6.1.4.1.272.4.2.4.1.18 |
isdnCallReceivedPacketsCount of received valid HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.4.1.19 |
isdnCallReceivedOctetsCount of received valid HDLC Octets.ro Counter .1.3.6.1.4.1.272.4.2.4.1.20 |
isdnCallReceivedErrorsCount of received invalid HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.4.1.21 |
isdnCallTransmitPacketsCount of transmitted HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.4.1.22 |
isdnCallTransmitOctetsCount of transmitted Octets.ro Counter .1.3.6.1.4.1.272.4.2.4.1.23 |
isdnCallTransmitErrorsCount of transmit errors (Collision, TX underrun).ro Counter .1.3.6.1.4.1.272.4.2.4.1.24 |
isdnCallChargeInfoTextual information of charge, i.e. 0.12 DM or 3 unitsro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.4.1.25 |
isdnCallScreeningScreening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by the telephone switching station. If the CPN was assigned by the user the switching station may optionally verify the address. indicator: CPN assigned: verification: `user' by user none `user-verified' by user verification successful `user-failed' by user verification failed `network' by network nonero Enumeration .1.3.6.1.4.1.272.4.2.4.1.26 |
isdnCallInfoAdditional information to identify the callro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.4.1.27 |
isdnDispatchTableThe isdnDispatchTable is the central distribution center for all incoming ISDN connections. Incoming ISDN connections are `dispatched' to a service (isdnDspItem) based on the calling party's number sent over the ISDN. Creating entries: Entries can be created by assigning a value to both the isdnDspStkNumber and isdnDspItem objects within one operation. Deleting entries: Entries are removed by setting the isdnDspItem to 'delete'. SEQUENCE OF IsdnDispatchEntry .1.3.6.1.4.1.272.4.2.5 |
isdnDispatchEntry IsdnDispatchEntry .1.3.6.1.4.1.272.4.2.5.1 |
isdnDspStkNumberThe ISDN stack number for this entry.rw INTEGER (-1..31) .1.3.6.1.4.1.272.4.2.5.1.1 |
isdnDspItemThe item to connect this call to. Routing tasks (IP, IPX, X.25, bridging, ...) should use the ppp(1). For the isdnlogin program use the login(2) item. For CAPI 1.1 programs, use items eaz0(48) .. eaz9(57).rw Enumeration .1.3.6.1.4.1.272.4.2.5.1.2 |
isdnDspLocalNumberIf the Called Party Number of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing calls from this item, the local number is sent as the Calling Party Number. Note: The matching of isdnDspLocalNumber value is done from right to left based on the number of digits in isdnDspLocalNumber. For example: if isdnDspLocalNumber is set to 124 then an incoming Called Party Number of 6501124 would match while one with 650024 would not.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.5.1.3 |
isdnDspLocalSubaddressIf the Called Party Subaddress of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing calls from this item, the local subaddress is sent as the Calling Party Subaddress. Note: The matching of isdnDspLocalSubaddress values is done by comparing the entire string of numbers in the Called Party Subaddress field. For example: if issdnDspLocalSubaddress is set to 072522 then only calls with an incoming Called Party Subaddress of 072522 would match, i.e. one with 522 would not match.rw OCTET STRING .1.3.6.1.4.1.272.4.2.5.1.4 |
isdnDspBearerThe isdnDspBearer is used for dispatching different types of callsrw Enumeration .1.3.6.1.4.1.272.4.2.5.1.5 |
isdnDspSlotIdentification number of the used slot.rw INTEGER .1.3.6.1.4.1.272.4.2.5.1.6 |
isdnDspUnitIdentification number of the used unit.rw INTEGER .1.3.6.1.4.1.272.4.2.5.1.7 |
isdnDspDirectionSpecifies whether the entry is to be used for outgoing calls, incoming calls or both.rw Enumeration .1.3.6.1.4.1.272.4.2.5.1.8 |
isdnDspModeThis object specifies the matching direction for incoming calls. When set to right-to-left, the rightmost digits of the called address of an incoming call are compared against the LocalNumber. This is useful for normal basic rate interfaces without DDI, because only few last digits have to be specified to be unique. When set to left-to-right, the leftmost digits of an incoming call are compared against the LocalNumber. Only the latter mode may be used for direct dialing in (DDI).rw Enumeration .1.3.6.1.4.1.272.4.2.5.1.9 |
isdnDspUserNameThe name of the user.rw DisplayString .1.3.6.1.4.1.272.4.2.5.1.10 |
isdnDChanX31TableThe isdnDChanX31Table contains information for the X.31 stack for each available ISDN D-channel. This information is mainly used for X.25 packet-switching functions but can be used for CAPI applications. The table is initialized during the auto configure process. By default the system polls each D-channel for an assigned TEI (terminal endpoint identifier). Creating entries: Entries can be added by assigning a new value (valid IfIndex) to isdnX31IsdnIfIndex. Deleting entries: Entries are removed by assigning 'delete' to the approprate isdnX31IsdnAssignedTo object. SEQUENCE OF IsdnDChanX31Entry .1.3.6.1.4.1.272.4.2.6 |
isdnDChanX31Entry IsdnDChanX31Entry .1.3.6.1.4.1.272.4.2.6.1 |
isdnX31IsdnIfIndexThe corresponding ISDN interface that is used for this call. Refer to the isdnIfTable.rw INTEGER .1.3.6.1.4.1.272.4.2.6.1.1 |
isdnX31TeiProcThe procedure used for polling of TEI (terminal end-point identifiers) values.rw Enumeration .1.3.6.1.4.1.272.4.2.6.1.2 |
isdnX31TeiValueThe TEI value for this interface.rw INTEGER (-1..126) .1.3.6.1.4.1.272.4.2.6.1.3 |
isdnX31AssignedToThe service this TEI value is assigned to.rw Enumeration .1.3.6.1.4.1.272.4.2.6.1.5 |
isdnAccountingTemplateSpecifies the format of accounting messages sent by the syslog protocol. The format can consist of any order of the following variables. Tag Meaning %S Date the connection opened; in DD.MM.YY format. %s Time the connection was established: in HH:MM:SS format %R Date the connection closed; in DD.MM.YY format. %r Time the connection was closed: in HH:MM:SS format. %d The duration of the connection in seconds. %D Call identification: internal/external, ID, slot/unit (PABX only) %P Call classification: Private/Business, project number (PABX only) %y Total number of bytes received over the connection. %Y Total number of bytes sent over the connection. %g Total packets received over the connection %G Total packets sent over the connection. %c Total number of charging units (value) incurred for the connection. %C Total number of charging units (string) incurred for the connection. %n The call's direction; either incoming (I) or outgoing (O). %Z The local address (Calling or Called party's number, see %n). %z The local subaddress (Calling or Called party's number, see %n). %T The remote address (Calling or Called party's number %n). %t The remote subaddress (Calling or Called party's number %n). %i Service indicator and additional information for the call. %b Bearer capability for the call. %l Low layer capability for the call. %h High layer capability for the call. %u DSS1 error cause, if applicable. %U 1tr6 error cause, if applicable. %L Local (internal) error cause. %F Call reference (internal). %e Calling extension (for call assiciation; PABX only) %I Information about the subsystem the call was given to. The default accounting template setting contains the following tags: %S,%s,%r,%d,%y,%Y,%g,%G,%C,%n,%Z,%T,%i,%u,%L,%I. This template produces accounting messages similar to the following. ISDN:18.08.1997,13:53:19,13:53:34,12,1096,1875,33,33,1Units,O,2,091196730,7/0,9F,0rw DisplayString .1.3.6.1.4.1.272.4.2.7 |
isdnCallHistoryTableThe isdnCallHistoryTable contains information pertaining to the last 20 ISDN calls made, since the last system startup. Each call that appears in the isdnCallTable, will have its information stored here (temporarily), once it disconnects. Creating entries: Entries are added by the system once a call is disconnected. Deleting entries: Entries are removed by the system. The table is designed as a circular queue (or FIFO); the most calls are stored at inx 19 with older calls rolling off the top of the table at inx 00. SEQUENCE OF IsdnCallHistoryEntry .1.3.6.1.4.1.272.4.2.8 |
isdnCallHistoryEntry IsdnCallEntry .1.3.6.1.4.1.272.4.2.8.1 |
isdnCallHistoryStkNumberThe number of the ISDN-Stack, this call went through.ro INTEGER .1.3.6.1.4.1.272.4.2.8.1.1 |
isdnCallHistoryTypeThe direction of the call, incoming or outgoing.ro Enumeration .1.3.6.1.4.1.272.4.2.8.1.2 |
isdnCallHistoryTimeThe time the call was received (incoming) or was placed (outgoing).ro Date .1.3.6.1.4.1.272.4.2.8.1.3 |
isdnCallHistoryDurationThe duration of the call in seconds.ro INTEGER .1.3.6.1.4.1.272.4.2.8.1.4 |
isdnCallHistoryIsdnIfIndexThe corresponding ISDN interface that this call used.ro INTEGER .1.3.6.1.4.1.272.4.2.8.1.5 |
isdnCallHistoryChannelThe corresponding B-channel on this ISDN interface.ro INTEGER .1.3.6.1.4.1.272.4.2.8.1.6 |
isdnCallHistoryDspItemThe item this call was connected to. Routing tasks (IP, IPX, X.25, bridging, ...) use ppp(1). The isdnlogin program uses login(2). CAPI 1.1 programs, use the items eaz0(48) .. eaz9(57) are used.ro Enumeration .1.3.6.1.4.1.272.4.2.8.1.7 |
isdnCallHistoryRemoteNumberThe ISDN number that was called (for outgoing calls) or was calling (for incoming calls).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.8.1.8 |
isdnCallHistoryRemoteSubaddressThe subaddress of the remote number. See isdnCall- HistoryRemoteNumber.ro OCTET STRING .1.3.6.1.4.1.272.4.2.8.1.9 |
isdnCallHistoryLocalNumberThe calling party number that was sent (with the outgoing call) or was received (with incoming calls).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.8.1.10 |
isdnCallHistoryLocalSubaddressThe subaddress of the calling party number.ro OCTET STRING .1.3.6.1.4.1.272.4.2.8.1.11 |
isdnCallHistoryServiceIndicatorService indicator that was sent on the ISDN D-channel when the call was established.ro Enumeration .1.3.6.1.4.1.272.4.2.8.1.12 |
isdnCallHistoryAddInfoAdditional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol.ro INTEGER .1.3.6.1.4.1.272.4.2.8.1.13 |
isdnCallHistoryBCBearer Capability that was sent on the ISDN D-channel when the call was established.ro OCTET STRING .1.3.6.1.4.1.272.4.2.8.1.14 |
isdnCallHistoryLLCLow Layer Capability that was sent on the ISDN D-channel when the call was established.ro OCTET STRING .1.3.6.1.4.1.272.4.2.8.1.15 |
isdnCallHistoryHLCHigh Layer Capability that was sent on the ISDN D-channel when the call was established.ro OCTET STRING .1.3.6.1.4.1.272.4.2.8.1.16 |
isdnCallHistoryChargeThe number of charging ticks received for this connection. Actual charges can be computed by multiplying this value with the unit price, e.g. .12 DM in Germany. If you aren't receiving charging information for outgoing calls, verify with your local ISDN provider to make sure this option being provided/is available. As an option, this Object may contain the charge measured in 1/1000 of the respective currency. See also ChargeInfo for textual information.ro INTEGER .1.3.6.1.4.1.272.4.2.8.1.17 |
isdnCallHistoryDSS1CauseISDN error condition reported by the DSS1 protocol, for Euro ISDN. See Appendix C in the User's Guide.ro HexValue .1.3.6.1.4.1.272.4.2.8.1.18 |
isdnCallHistory1TR6CauseISDN error condition reported by the 1TR6 protocol, for National ISDN in Germany. See Appendix C in the User's Guide.ro HexValue .1.3.6.1.4.1.272.4.2.8.1.19 |
isdnCallHistoryLocalCauseISDN error condition reported by the system locally. See Appendix C in the User's Guide.ro Enumeration .1.3.6.1.4.1.272.4.2.8.1.20 |
isdnCallHistoryChargeInfoTextual information of charge, i.e. 0.12 DM or 3 unitsro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.8.1.21 |
isdnCallHistoryScreeningScreening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by the telephone switching station. If the CPN was assigned by the user the switching station may optionally verify the address. indicator: CPN assigned: verification: `user' by user none `user-verified' by user verification successful `user-failed' by user verification failed `network' by network nonero Enumeration .1.3.6.1.4.1.272.4.2.8.1.22 |
isdnCallHistoryInfoAdditional information to identify the callro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.8.1.23 |
isdnCallHistoryReceivedPacketsCount of received valid HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.8.1.24 |
isdnCallHistoryReceivedOctetsCount of received valid HDLC Octets.ro Counter .1.3.6.1.4.1.272.4.2.8.1.25 |
isdnCallHistoryReceivedErrorsCount of received invalid HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.8.1.26 |
isdnCallHistoryTransmitPacketsCount of transmitted HDLC Frames.ro Counter .1.3.6.1.4.1.272.4.2.8.1.27 |
isdnCallHistoryTransmitOctetsCount of transmitted Octets.ro Counter .1.3.6.1.4.1.272.4.2.8.1.28 |
isdnCallHistoryTransmitErrorsCount of transmit errors (Collision, TX underrun).ro Counter .1.3.6.1.4.1.272.4.2.8.1.29 |
isdnLoginOnPPPDispatchAllows or disallows incoming ISDN calls (with an ISDN service indicator of 'telephony'), to be connected to the isdnlogin daemon even though the call has a matching service in the isdnDispatchTable (isdnDspItem). These calls must be initiated using isdnlogin <telno> telephony.rw Enumeration .1.3.6.1.4.1.272.4.2.9 |
isdnHistoryMaxEntriesMaximum number of isdnCallHistory entries in memory.rw INTEGER .1.3.6.1.4.1.272.4.2.10 |
isdnloginAllowTableThe isdnloginAllowTable contains information about the ISDN partners that are allowed to login to the BRICK via the isdnlogin service. ISDN callers are identified by their calling partner number. Incoming isdnlogin requests can be restricted to single ISDN stacks. If this table is empty all calls given to the isdnlogind, are accepted. (Note that the isdnDispatchTable is consulted first.) Creating entries: Entries are created by assigning a value to the isdnloginAllowStkNumber object. Deleting entries: An entry can be removed by assigning the value `delete' to its isdnloginAllowScreening object. SEQUENCE OF IsdnloginAllowEntry .1.3.6.1.4.1.272.4.2.11 |
isdnloginAllowEntry IsdnloginAllowEntry .1.3.6.1.4.1.272.4.2.11.1 |
isdnloginAllowStkNumberThe number of the ISDN stack, that accepts incoming isdnlogin calls. Refer to the isdnStkTable. The value `-1' matches all available stacks.rw INTEGER (-1..31) .1.3.6.1.4.1.272.4.2.11.1.1 |
isdnloginAllowRemoteNumberThe number of the ISDN partner that is allowed to login via isdnlogin through the corresponding ISDN Stack. The wildcards '*', '?', '[', ']', '{', '}' may be used. See isdnCallRemoteNumber.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.272.4.2.11.1.2 |
isdnloginAllowRemoteSubaddressThe subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnloginAllowRemoteNumber.rw OCTET STRING .1.3.6.1.4.1.272.4.2.11.1.3 |
isdnloginAllowScreeningThe screening indicator of the calling party number (CPN). The isdnloginAllowScreening field can be used to gauge the `trustworthiness' of the CPN field (see isdnCallScreening). Indicators are ordered from highest to lowest as follows: indicator: CPN assigned: verification: `network' by network none `user-verified' by user verification successful `user' by user none `user-failed' by user verification failed Set this field to `dont-care' to accept all calls. Set this field to `delete' to delete this entry. Otherwise calls are accepted only if the screening indicator matches or is higher than the set value.rw Enumeration .1.3.6.1.4.1.272.4.2.11.1.4 |
isdnCreditsTableThe isdnCreditsTable contains informations about current used resources and maximum allowed resources for each during a specified interval subsystem. Creating entries: Entries are added by the system during startup. Deleting entries: Is not possible. SEQUENCE OF IsdnCreditsEntry .1.3.6.1.4.1.272.4.2.12 |
isdnCreditsEntry IsdnCreditsEntry .1.3.6.1.4.1.272.4.2.12.1 |
isdnCreditsSubsysNumberType of Subsystem.ro Enumeration .1.3.6.1.4.1.272.4.2.12.1.1 |
isdnCreditsSurveillanceSurveillance on or off.rw Enumeration .1.3.6.1.4.1.272.4.2.12.1.2 |
isdnCreditsMeasuretimeTime of one observation interval in seconds.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.3 |
isdnCreditsMaxInConMaximum number of allowed incoming connections during the observation interval. -1 disables this limit.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.4 |
isdnCreditsMaxOutConMaximum number of allowed outgoing connections during the observation interval. -1 disables this limit.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.5 |
isdnCreditsMaxChargeMaximum allowed charge amount during the observation interval. -1 disables this limit.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.6 |
isdnCreditsMaxInDurationMaximum connect time for incoming connections in seconds during the observation interval. -1 disables this limit.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.7 |
isdnCreditsMaxOutDurationMaximum connect time for outgoing connections in seconds during the observation interval. -1 disables this limitrw INTEGER .1.3.6.1.4.1.272.4.2.12.1.8 |
isdnCreditsTimeleftTime in seconds left in current interval. Writing to Timeleft will restart the observation interval.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.9 |
isdnCreditsCurrentInConCurrent number of incoming connections.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.10 |
isdnCreditsCurrentOutConCurrent number of outgoing connections.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.11 |
isdnCreditsTotalInConTotal count of incoming connections during the observation interval.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.12 |
isdnCreditsTotalOutConTotal count of outgoing connections during the observation interval.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.13 |
isdnCreditsTotalMaxConMaximum number of simultaniously established connections during the observation interval.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.14 |
isdnCreditsTotalChargeTotal accounted charge during the observation interval.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.15 |
isdnCreditsTotalInDurationTotal connect time of incoming connections during the observation interval.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.16 |
isdnCreditsTotalOutDurationTotal connect time of outgoing connections during the observation interval.ro INTEGER .1.3.6.1.4.1.272.4.2.12.1.17 |
isdnCreditsMaxCurrentInConMaximum number of currently allowed incoming connections. -1 disables this limit.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.18 |
isdnCreditsMaxCurrentOutConMaximum number of currently allowed outgoing connections. -1 disables this limit.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.19 |
isdnCreditsMaxCurrentConMaximum number of currently allowed connections in both directions. -1 disables this limit.rw INTEGER .1.3.6.1.4.1.272.4.2.12.1.20 |