BIANCA-BRICK-HDSL2SHDSL2-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for BIANCA-BRICK-HDSL2SHDSL2-MIB.
82
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
82 total| Object Name |
|---|
bintec OBJECT IDENTIFIER .1.3.6.1.4.1.272 |
RFC-1215 Unknown .1.3.6.1.4.1.272 |
bibo OBJECT IDENTIFIER .1.3.6.1.4.1.272.4 |
hdsl2shdsl OBJECT IDENTIFIER .1.3.6.1.4.1.272.4.35 |
hdsl2ShdslLineMib OBJECT IDENTIFIER .1.3.6.1.4.1.272.4.35.1 |
hdsl2ShdslMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.272.4.35.1.1 |
hdsl2ShdslInventoryTableThis table supports retrieval of unit inventory information
available via the EOC from units in a HDSL2/SHDSL line.
Entries in this table are dynamically created during the
line discovery process. The life cycle for these entries
is as follows:
- xtu discovers a device, either a far-end xtu or an xru
- an inventory table entry is created for the device
- the line goes down for whatever reason
- inventory table entries for unreachable devices are
destroyed.
As these entries are created/destroyed dynamically, they
are NOT persistent. SEQUENCE OF Hdsl2ShdslInventoryEntry .1.3.6.1.4.1.272.4.35.1.1.3 |
hdsl2ShdslInventoryEntryAn entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line. Hdsl2ShdslInventoryEntry .1.3.6.1.4.1.272.4.35.1.1.3.1 |
hdsl2ShdslInvIfIndexThis object specifies the associated interface index of
this HDSL2/SHDSL line.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.3.1.1 |
hdsl2ShdslInvIndexEach entry in this table corresponds to a physical element
in a HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC.ro Enumeration .1.3.6.1.4.1.272.4.35.1.1.3.1.2 |
hdsl2ShdslInvVendorIDVendor ID as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.3 |
hdsl2ShdslInvVendorModelNumberVendor model number as reported in an Inventory Response
message.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.4 |
hdsl2ShdslInvVendorSerialNumberVendor serial number as reported in an Inventory Response
message.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.5 |
hdsl2ShdslInvVendorEOCSoftwareVersionVendor EOC version as reported in a Discovery Response
message.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.3.1.6 |
hdsl2ShdslInvStandardVersionVersion of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.3.1.7 |
hdsl2ShdslInvVendorListNumberVendor list number as reported in an Inventory Response
message.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.8 |
hdsl2ShdslInvVendorIssueNumberVendor issue number as reported in an Inventory Response
message.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.9 |
hdsl2ShdslInvVendorSoftwareVersionVendor software version as reported in an Inventory Response
message.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.10 |
hdsl2ShdslInvEquipmentCodeEquipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.11 |
hdsl2ShdslInvVendorOtherOther vendor information as reported in an Inventory Response
message.ro OCTET STRING .1.3.6.1.4.1.272.4.35.1.1.3.1.12 |
hdsl2ShdslInvTransmissionModeCapabilityContains the transmission mode capability of the SHDSL unit:
region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex Bro Enumeration .1.3.6.1.4.1.272.4.35.1.1.3.1.13 |
hdsl2ShdslEndpointConfTableThis table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner.
Entries in this table are created by the system only. SEQUENCE OF Hdsl2ShdslEndpointConfEntry .1.3.6.1.4.1.272.4.35.1.1.4 |
hdsl2ShdslEndpointConfEntryAn entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line. Hdsl2ShdslEndpointConfEntry .1.3.6.1.4.1.272.4.35.1.1.4.1 |
hdsl2ShdslEndpointConfIfIndexThis object specifies the associated interface index of
this HDSL2/SHDSL line.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.1 |
hdsl2ShdslEndpointConfSideThe side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide textual
convention.rw Enumeration .1.3.6.1.4.1.272.4.35.1.1.4.1.2 |
hdsl2ShdslEndpointConfWireInterfaceThis object configures the bonding mode of
the SHDSL Line.
twoWire(1) : no bonding is used
fourWire(2) : four-wire mode
fourWireStandard(3) : four-wire mode, disable globespan enhanced mode
fourWireIMA(4) : 2 wire pairs bonded with IMA
sixWire(5) : 3 wire pairs in m-pair mode
sixWireIMA(6) : 3 wire pairs bonded with IMA
eightWire(7) : 4 wire pairs in m-pair mode
eightWireIMA(8) : 4 wire pairs bonded with IMA
not-used(9) : wire pair inactive
groupMember(10) : wire pair belongs to a bonding group
twoWireEFM(11) : 2 wire EFM mode
fourWireEFM(12) : 2 wire pairs in EFM mode with PAF bonding
sixWireEFM(13) : 3 wire pairs in EFM mode with PAF bonding
eightWireEFM(14) : 4 wire pairs in EFM mode with PAF bondingrw Enumeration .1.3.6.1.4.1.272.4.35.1.1.4.1.5 |
hdsl2ShdslEndpointConfMinLineRateThis object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.6 |
hdsl2ShdslEndpointConfMaxLineRateThis object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.7 |
hdsl2ShdslEndpointConfTransmissionModeThis object specifies the regional setting for the SHDSL
line:
region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex Brw Enumeration .1.3.6.1.4.1.272.4.35.1.1.4.1.8 |
hdsl2ShdslEndpointConfWorstCaseTargetMarginDownThis object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.11 |
hdsl2ShdslEndpointConfWorstCaseTargetMarginUpThis object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit.rw INTEGER (-10..21) -- UNITS "dB" .1.3.6.1.4.1.272.4.35.1.1.4.1.13 |
hdsl2ShdslEndpointConfGroupIdThis object defines which wire-pairs belong to the same
M-pair group or IMA group. Members of the same group have
the same entry.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.14 |
hdsl2ShdslEndpointConfLineProbeEnableThis object specifies the configuration of the PMMS
behavior:
auto - Line Probe is enabled if hdsl2ShdslEndpointConfMinLineRate
< hdsl2ShdslEndpointConfMaxLineRate.
disable - Line Probe is disabled.
enable - Line Probe is enabled.
enable_std - Line Probe is enabled and standard
compliant behaviour is enforced.rw Enumeration .1.3.6.1.4.1.272.4.35.1.1.4.1.15 |
hdsl2ShdslEndpointConfLicenseUsageShows which license type is currently used for this
SHDSL interface.ro Enumeration .1.3.6.1.4.1.272.4.35.1.1.4.1.16 |
hdsl2ShdslEndpointConfPamModeThis object specifies which modulation modes are allowed
for this wire pair.
16 - 16-TCPAM, used for Annex A,B and F,G.
32 - 32-TCPAM, used for Annex F,G only.
4, 8, 64, 128 - non standard proprietary modes.
On CPE site more than one mode can be allowed by adding
the values.
On CO site only the highest mode is used if several
values are added.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.17 |
hdsl2ShdslEndpointConfTotalMinLineRateThis object configures the minimum transmission rate
in bits-per-second (bps) for the associated SHDSL bundle.
The associated interfaces go up only when the sum of the
data rates of the associated wire pairs in state Showtime
reaches or exceeds the specified value.
This variable has no effect with single pair modes.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.18 |
hdsl2ShdslEndpointConfMinWirePairsThis object configures the minimum number of wire pairs
for the associated SHDSL bundle. The associated interfaces
go up only when at least the specified number of wire pairs
is connected and in Showtime.
This variable has no effect with single pair modes.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.4.1.19 |
hdsl2ShdslEndpointConfCapListStyleThis object specifies the data format of the capability list,
that is exchanged during the G.994.1 handshake:
auto - automatic detection of the used capability list style.
old - only ATM modes till 2312 kbps can be negotiated.
new - all modes can be negotiated.rw Enumeration .1.3.6.1.4.1.272.4.35.1.1.4.1.20 |
hdsl2ShdslEndpointCurrTableThis table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner. Entries in this
table are created by the system only. SEQUENCE OF Hdsl2ShdslEndpointCurrEntry .1.3.6.1.4.1.272.4.35.1.1.5 |
hdsl2ShdslEndpointCurrEntryAn entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line. Hdsl2ShdslEndpointCurrEntry .1.3.6.1.4.1.272.4.35.1.1.5.1 |
hdsl2ShdslEndpointCurrIfIndexThis object specifies the associated interface index of
this HDSL2/SHDSL line.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.1 |
hdsl2ShdslEndpointCurrReceivedBlksCount of all encoded blocks received on this channel
since agent reset.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.2 |
hdsl2ShdslEndpointCurrTransmittedBlksCount of all encoded blocks transmitted on this channel
since agent reset.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.3 |
hdsl2ShdslEndpointCurrCorrectedBlksCount of all blocks received with errors that were
corrected since agent reset. These blocks are passed
on as good data.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.4 |
hdsl2ShdslEndpointCurrUncorrectBlksCount of all blocks received with uncorrectable errors
since agent reset.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.5 |
hdsl2ShdslEndpointCurrAtnThe current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message.ro INTEGER (-127..128) -- UNITS "dB" .1.3.6.1.4.1.272.4.35.1.1.5.1.6 |
hdsl2ShdslEndpointCurrSnrMgnThe current SNR margin for this endpoint as reported in a
Status Response/SNR message.ro INTEGER (-127..128) -- UNITS "dB" .1.3.6.1.4.1.272.4.35.1.1.5.1.7 |
hdsl2ShdslEndpointCurrStatusContains the current state of the endpoint. This is a
bitmap of possible conditions. The various bit positions
are:
noDefect There no defects on the line.
powerBackoff Indicates enhanced Power Backoff.
deviceFault Indicates a vendor-dependent
diagnostic or self-test fault
has been detected.
dcContinuityFault Indicates vendor-dependent
conditions that interfere with
span powering such as short and
open circuits.
snrMarginAlarm Indicates that the SNR margin
has dropped below the alarm threshold.
loopAttenuationAlarm Indicates that the loop attenuation
exceeds the alarm threshold.
(not supported by GlobeSpan !)
loswFailureAlarm Indicates a forward LOSW alarm.
configInitFailure Endpoint failure during initialization
due to paired endpoint not able to
support requested configuration.
protocolInitFailure Endpoint failure during initialization
due to incompatible protocol used by
the paired endpoint.
noNeighborPresent Endpoint failure during initialization
due to no activation sequence detected
from paired endpoint.
loopbackActive A loopback is currently active at this
Segment Endpoint.
This is intended to supplement ifOperStatus. Note that there
is a 1-1 relationship between the status bits defined in this
object and the notification thresholds defined elsewhere in
this MIB.ro Enumeration .1.3.6.1.4.1.272.4.35.1.1.5.1.8 |
hdsl2ShdslEndpointESCount of Errored Seconds (ES) on this endpoint since the xU
was last restarted.ro Counter -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.9 |
hdsl2ShdslEndpointSESCount of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted.ro Counter -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.10 |
hdsl2ShdslEndpointCRCanomaliesCount of CRC anomalies on this endpoint since the xU was
last restarted.ro Counter -- UNITS "detected CRC Anomalies" .1.3.6.1.4.1.272.4.35.1.1.5.1.11 |
hdsl2ShdslEndpointLOSWSCount of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted.ro Counter -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.12 |
hdsl2ShdslEndpointUASCount of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted.ro Counter -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.13 |
hdsl2ShdslEndpointCurr15MinReceivedBlksCount of all encoded blocks received on this channel
within the mandatory 15 minute interval.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.14 |
hdsl2ShdslEndpointCurr15MinTransmittedBlksCount of all encoded blocks transmitted on this channel
within the mandatory 15 minute interval.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.15 |
hdsl2ShdslEndpointCurr15MinCorrectedBlksCount of all blocks received with errors that were
corrected on this channel within the mandatory 15 minute
interval.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.16 |
hdsl2ShdslEndpointCurr15MinUncorrectBlksCount of all blocks received with uncorrectable errors
on this channel within the mandatory 15 minute interval.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.17 |
hdsl2ShdslEndpointCurr15MinTimeElapsedTotal elapsed seconds in the current 15-minute interval.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.18 |
hdsl2ShdslEndpointCurr15MinESCount of Errored Seconds (ES) in the current 15-minute
interval.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.19 |
hdsl2ShdslEndpointCurr15MinSESCount of Severely Errored Seconds (SES) in the current
15-minute interval.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.20 |
hdsl2ShdslEndpointCurr15MinCRCanomaliesCount of CRC anomalies in the current 15-minute interval.ro INTEGER -- UNITS "detected CRC Anomalies" .1.3.6.1.4.1.272.4.35.1.1.5.1.21 |
hdsl2ShdslEndpointCurr15MinLOSWSCount of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.22 |
hdsl2ShdslEndpointCurr15MinUASCount of Unavailable Seconds (UAS) in the current 15-minute
interval.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.23 |
hdsl2ShdslEndpointCurr1DayReceivedBlksCount of all encoded blocks received on this channel
during the mandatory day as measured by
hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.24 |
hdsl2ShdslEndpointCurr1DayTransmittedBlksCount of all encoded blocks transmitted on this channel
during the mandatory day as measured by
hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.25 |
hdsl2ShdslEndpointCurr1DayCorrectedBlksCount of all blocks received with errors that were
corrected on this channel during the mandatory day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.26 |
hdsl2ShdslEndpointCurr1DayUncorrectBlksCount of all blocks received with uncorrectable errors
on this channel during the mandatory day as measured by
hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.27 |
hdsl2ShdslEndpointCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of
the current 1-day interval.ro INTEGER .1.3.6.1.4.1.272.4.35.1.1.5.1.28 |
hdsl2ShdslEndpointCurr1DayESCount of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.29 |
hdsl2ShdslEndpointCurr1DaySESCount of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.30 |
hdsl2ShdslEndpointCurr1DayCRCanomaliesCount of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER -- UNITS "detected CRC Anomalies" .1.3.6.1.4.1.272.4.35.1.1.5.1.31 |
hdsl2ShdslEndpointCurr1DayLOSWSCount of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.32 |
hdsl2ShdslEndpointCurr1DayUASCount of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro INTEGER -- UNITS "seconds" .1.3.6.1.4.1.272.4.35.1.1.5.1.33 |
hdsl2ShdslSpanConfProfileTableThis table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner. Entries in this table are created by
the system only. SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry .1.3.6.1.4.1.272.4.35.1.1.10 |
hdsl2ShdslSpanConfProfileEntryEach entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted only by the system. Hdsl2ShdslSpanConfProfileEntry .1.3.6.1.4.1.272.4.35.1.1.10.1 |
hdsl2ShdslSpanConfProfileNameThis object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry.ro DisplayString .1.3.6.1.4.1.272.4.35.1.1.10.1.1 |
hdsl2ShdslSpanConfWireInterfaceThis object configures the bonding mode of
the SHDSL Line.
twoWire(1) : no bonding is used
fourWire(2) : four-wire mode
fourWireStandard(3) : four-wire mode, disable globespan enhanced mode
fourWireIMA(4) : 2 wire pairs bonded with IMA
sixWire(5) : 3 wire pairs in m-pair mode
sixWireIMA(6) : 3 wire pairs bonded with IMA
eightWire(7) : 4 wire pairs in m-pair mode
eightWireIMA(8) : 4 wire pairs bonded with IMA
not-used(9) : wire pair inactive
groupMember(10) : wire pair belongs to a bonding group
twoWireEFM(11) : 2 wire EFM mode
fourWireEFM(12) : 2 wire pairs in EFM mode with PAF bonding
sixWireEFM(13) : 3 wire pairs in EFM mode with PAF bonding
eightWireEFM(14) : 4 wire pairs in EFM mode with PAF bondingrw Enumeration .1.3.6.1.4.1.272.4.35.1.1.10.1.2 |
hdsl2ShdslSpanConfMinLineRateThis object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.10.1.3 |
hdsl2ShdslSpanConfMaxLineRateThis object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.10.1.4 |
hdsl2ShdslSpanConfTransmissionModeThis object specifies the regional setting for the SHDSL
line:
region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex Brw Enumeration .1.3.6.1.4.1.272.4.35.1.1.10.1.6 |
hdsl2ShdslSpanConfWorstCaseTargetMarginDownThis object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit.rw INTEGER .1.3.6.1.4.1.272.4.35.1.1.10.1.10 |
hdsl2ShdslSpanConfWorstCaseTargetMarginUpThis object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit.rw INTEGER (-10..21) -- UNITS "dB" .1.3.6.1.4.1.272.4.35.1.1.10.1.12 |